1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * Copyright (C) 2015 Microchip Technology 4 */ 5 #include <linux/kernel.h> 6 #include <linux/module.h> 7 #include <linux/mii.h> 8 #include <linux/ethtool.h> 9 #include <linux/phy.h> 10 #include <linux/microchipphy.h> 11 #include <linux/delay.h> 12 #include <linux/of.h> 13 #include <dt-bindings/net/microchip-lan78xx.h> 14 15 #define DRIVER_AUTHOR "WOOJUNG HUH <woojung.huh@microchip.com>" 16 #define DRIVER_DESC "Microchip LAN88XX PHY driver" 17 18 struct lan88xx_priv { 19 int chip_id; 20 int chip_rev; 21 __u32 wolopts; 22 }; 23 24 static int lan88xx_read_page(struct phy_device *phydev) 25 { 26 return __phy_read(phydev, LAN88XX_EXT_PAGE_ACCESS); 27 } 28 29 static int lan88xx_write_page(struct phy_device *phydev, int page) 30 { 31 return __phy_write(phydev, LAN88XX_EXT_PAGE_ACCESS, page); 32 } 33 34 static int lan88xx_phy_config_intr(struct phy_device *phydev) 35 { 36 int rc; 37 38 if (phydev->interrupts == PHY_INTERRUPT_ENABLED) { 39 /* unmask all source and clear them before enable */ 40 rc = phy_write(phydev, LAN88XX_INT_MASK, 0x7FFF); 41 rc = phy_read(phydev, LAN88XX_INT_STS); 42 rc = phy_write(phydev, LAN88XX_INT_MASK, 43 LAN88XX_INT_MASK_MDINTPIN_EN_ | 44 LAN88XX_INT_MASK_LINK_CHANGE_); 45 } else { 46 rc = phy_write(phydev, LAN88XX_INT_MASK, 0); 47 if (rc) 48 return rc; 49 50 /* Ack interrupts after they have been disabled */ 51 rc = phy_read(phydev, LAN88XX_INT_STS); 52 } 53 54 return rc < 0 ? rc : 0; 55 } 56 57 static irqreturn_t lan88xx_handle_interrupt(struct phy_device *phydev) 58 { 59 int irq_status; 60 61 irq_status = phy_read(phydev, LAN88XX_INT_STS); 62 if (irq_status < 0) { 63 phy_error(phydev); 64 return IRQ_NONE; 65 } 66 67 if (!(irq_status & LAN88XX_INT_STS_LINK_CHANGE_)) 68 return IRQ_NONE; 69 70 phy_trigger_machine(phydev); 71 72 return IRQ_HANDLED; 73 } 74 75 static int lan88xx_suspend(struct phy_device *phydev) 76 { 77 struct lan88xx_priv *priv = phydev->priv; 78 79 /* do not power down PHY when WOL is enabled */ 80 if (!priv->wolopts) 81 genphy_suspend(phydev); 82 83 return 0; 84 } 85 86 static int lan88xx_TR_reg_set(struct phy_device *phydev, u16 regaddr, 87 u32 data) 88 { 89 int val, save_page, ret = 0; 90 u16 buf; 91 92 /* Save current page */ 93 save_page = phy_save_page(phydev); 94 if (save_page < 0) { 95 phydev_warn(phydev, "Failed to get current page\n"); 96 goto err; 97 } 98 99 /* Switch to TR page */ 100 lan88xx_write_page(phydev, LAN88XX_EXT_PAGE_ACCESS_TR); 101 102 ret = __phy_write(phydev, LAN88XX_EXT_PAGE_TR_LOW_DATA, 103 (data & 0xFFFF)); 104 if (ret < 0) { 105 phydev_warn(phydev, "Failed to write TR low data\n"); 106 goto err; 107 } 108 109 ret = __phy_write(phydev, LAN88XX_EXT_PAGE_TR_HIGH_DATA, 110 (data & 0x00FF0000) >> 16); 111 if (ret < 0) { 112 phydev_warn(phydev, "Failed to write TR high data\n"); 113 goto err; 114 } 115 116 /* Config control bits [15:13] of register */ 117 buf = (regaddr & ~(0x3 << 13));/* Clr [14:13] to write data in reg */ 118 buf |= 0x8000; /* Set [15] to Packet transmit */ 119 120 ret = __phy_write(phydev, LAN88XX_EXT_PAGE_TR_CR, buf); 121 if (ret < 0) { 122 phydev_warn(phydev, "Failed to write data in reg\n"); 123 goto err; 124 } 125 126 usleep_range(1000, 2000);/* Wait for Data to be written */ 127 val = __phy_read(phydev, LAN88XX_EXT_PAGE_TR_CR); 128 if (!(val & 0x8000)) 129 phydev_warn(phydev, "TR Register[0x%X] configuration failed\n", 130 regaddr); 131 err: 132 return phy_restore_page(phydev, save_page, ret); 133 } 134 135 static void lan88xx_config_TR_regs(struct phy_device *phydev) 136 { 137 int err; 138 139 /* Get access to Channel 0x1, Node 0xF , Register 0x01. 140 * Write 24-bit value 0x12B00A to register. Setting MrvlTrFix1000Kf, 141 * MrvlTrFix1000Kp, MasterEnableTR bits. 142 */ 143 err = lan88xx_TR_reg_set(phydev, 0x0F82, 0x12B00A); 144 if (err < 0) 145 phydev_warn(phydev, "Failed to Set Register[0x0F82]\n"); 146 147 /* Get access to Channel b'10, Node b'1101, Register 0x06. 148 * Write 24-bit value 0xD2C46F to register. Setting SSTrKf1000Slv, 149 * SSTrKp1000Mas bits. 150 */ 151 err = lan88xx_TR_reg_set(phydev, 0x168C, 0xD2C46F); 152 if (err < 0) 153 phydev_warn(phydev, "Failed to Set Register[0x168C]\n"); 154 155 /* Get access to Channel b'10, Node b'1111, Register 0x11. 156 * Write 24-bit value 0x620 to register. Setting rem_upd_done_thresh 157 * bits 158 */ 159 err = lan88xx_TR_reg_set(phydev, 0x17A2, 0x620); 160 if (err < 0) 161 phydev_warn(phydev, "Failed to Set Register[0x17A2]\n"); 162 163 /* Get access to Channel b'10, Node b'1101, Register 0x10. 164 * Write 24-bit value 0xEEFFDD to register. Setting 165 * eee_TrKp1Long_1000, eee_TrKp2Long_1000, eee_TrKp3Long_1000, 166 * eee_TrKp1Short_1000,eee_TrKp2Short_1000, eee_TrKp3Short_1000 bits. 167 */ 168 err = lan88xx_TR_reg_set(phydev, 0x16A0, 0xEEFFDD); 169 if (err < 0) 170 phydev_warn(phydev, "Failed to Set Register[0x16A0]\n"); 171 172 /* Get access to Channel b'10, Node b'1101, Register 0x13. 173 * Write 24-bit value 0x071448 to register. Setting 174 * slv_lpi_tr_tmr_val1, slv_lpi_tr_tmr_val2 bits. 175 */ 176 err = lan88xx_TR_reg_set(phydev, 0x16A6, 0x071448); 177 if (err < 0) 178 phydev_warn(phydev, "Failed to Set Register[0x16A6]\n"); 179 180 /* Get access to Channel b'10, Node b'1101, Register 0x12. 181 * Write 24-bit value 0x13132F to register. Setting 182 * slv_sigdet_timer_val1, slv_sigdet_timer_val2 bits. 183 */ 184 err = lan88xx_TR_reg_set(phydev, 0x16A4, 0x13132F); 185 if (err < 0) 186 phydev_warn(phydev, "Failed to Set Register[0x16A4]\n"); 187 188 /* Get access to Channel b'10, Node b'1101, Register 0x14. 189 * Write 24-bit value 0x0 to register. Setting eee_3level_delay, 190 * eee_TrKf_freeze_delay bits. 191 */ 192 err = lan88xx_TR_reg_set(phydev, 0x16A8, 0x0); 193 if (err < 0) 194 phydev_warn(phydev, "Failed to Set Register[0x16A8]\n"); 195 196 /* Get access to Channel b'01, Node b'1111, Register 0x34. 197 * Write 24-bit value 0x91B06C to register. Setting 198 * FastMseSearchThreshLong1000, FastMseSearchThreshShort1000, 199 * FastMseSearchUpdGain1000 bits. 200 */ 201 err = lan88xx_TR_reg_set(phydev, 0x0FE8, 0x91B06C); 202 if (err < 0) 203 phydev_warn(phydev, "Failed to Set Register[0x0FE8]\n"); 204 205 /* Get access to Channel b'01, Node b'1111, Register 0x3E. 206 * Write 24-bit value 0xC0A028 to register. Setting 207 * FastMseKp2ThreshLong1000, FastMseKp2ThreshShort1000, 208 * FastMseKp2UpdGain1000, FastMseKp2ExitEn1000 bits. 209 */ 210 err = lan88xx_TR_reg_set(phydev, 0x0FFC, 0xC0A028); 211 if (err < 0) 212 phydev_warn(phydev, "Failed to Set Register[0x0FFC]\n"); 213 214 /* Get access to Channel b'01, Node b'1111, Register 0x35. 215 * Write 24-bit value 0x041600 to register. Setting 216 * FastMseSearchPhShNum1000, FastMseSearchClksPerPh1000, 217 * FastMsePhChangeDelay1000 bits. 218 */ 219 err = lan88xx_TR_reg_set(phydev, 0x0FEA, 0x041600); 220 if (err < 0) 221 phydev_warn(phydev, "Failed to Set Register[0x0FEA]\n"); 222 223 /* Get access to Channel b'10, Node b'1101, Register 0x03. 224 * Write 24-bit value 0x000004 to register. Setting TrFreeze bits. 225 */ 226 err = lan88xx_TR_reg_set(phydev, 0x1686, 0x000004); 227 if (err < 0) 228 phydev_warn(phydev, "Failed to Set Register[0x1686]\n"); 229 } 230 231 static int lan88xx_probe(struct phy_device *phydev) 232 { 233 struct device *dev = &phydev->mdio.dev; 234 struct lan88xx_priv *priv; 235 u32 led_modes[4]; 236 int len; 237 238 priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); 239 if (!priv) 240 return -ENOMEM; 241 242 priv->wolopts = 0; 243 244 len = of_property_read_variable_u32_array(dev->of_node, 245 "microchip,led-modes", 246 led_modes, 247 0, 248 ARRAY_SIZE(led_modes)); 249 if (len >= 0) { 250 u32 reg = 0; 251 int i; 252 253 for (i = 0; i < len; i++) { 254 if (led_modes[i] > 15) 255 return -EINVAL; 256 reg |= led_modes[i] << (i * 4); 257 } 258 for (; i < ARRAY_SIZE(led_modes); i++) 259 reg |= LAN78XX_FORCE_LED_OFF << (i * 4); 260 (void)phy_write(phydev, LAN78XX_PHY_LED_MODE_SELECT, reg); 261 } else if (len == -EOVERFLOW) { 262 return -EINVAL; 263 } 264 265 /* these values can be used to identify internal PHY */ 266 priv->chip_id = phy_read_mmd(phydev, 3, LAN88XX_MMD3_CHIP_ID); 267 priv->chip_rev = phy_read_mmd(phydev, 3, LAN88XX_MMD3_CHIP_REV); 268 269 phydev->priv = priv; 270 271 return 0; 272 } 273 274 static void lan88xx_remove(struct phy_device *phydev) 275 { 276 struct device *dev = &phydev->mdio.dev; 277 struct lan88xx_priv *priv = phydev->priv; 278 279 if (priv) 280 devm_kfree(dev, priv); 281 } 282 283 static int lan88xx_set_wol(struct phy_device *phydev, 284 struct ethtool_wolinfo *wol) 285 { 286 struct lan88xx_priv *priv = phydev->priv; 287 288 priv->wolopts = wol->wolopts; 289 290 return 0; 291 } 292 293 static void lan88xx_set_mdix(struct phy_device *phydev) 294 { 295 int buf; 296 int val; 297 298 switch (phydev->mdix_ctrl) { 299 case ETH_TP_MDI: 300 val = LAN88XX_EXT_MODE_CTRL_MDI_; 301 break; 302 case ETH_TP_MDI_X: 303 val = LAN88XX_EXT_MODE_CTRL_MDI_X_; 304 break; 305 case ETH_TP_MDI_AUTO: 306 val = LAN88XX_EXT_MODE_CTRL_AUTO_MDIX_; 307 break; 308 default: 309 return; 310 } 311 312 phy_write(phydev, LAN88XX_EXT_PAGE_ACCESS, LAN88XX_EXT_PAGE_SPACE_1); 313 buf = phy_read(phydev, LAN88XX_EXT_MODE_CTRL); 314 buf &= ~LAN88XX_EXT_MODE_CTRL_MDIX_MASK_; 315 buf |= val; 316 phy_write(phydev, LAN88XX_EXT_MODE_CTRL, buf); 317 phy_write(phydev, LAN88XX_EXT_PAGE_ACCESS, LAN88XX_EXT_PAGE_SPACE_0); 318 } 319 320 static int lan88xx_config_init(struct phy_device *phydev) 321 { 322 int val; 323 324 /*Zerodetect delay enable */ 325 val = phy_read_mmd(phydev, MDIO_MMD_PCS, 326 PHY_ARDENNES_MMD_DEV_3_PHY_CFG); 327 val |= PHY_ARDENNES_MMD_DEV_3_PHY_CFG_ZD_DLY_EN_; 328 329 phy_write_mmd(phydev, MDIO_MMD_PCS, PHY_ARDENNES_MMD_DEV_3_PHY_CFG, 330 val); 331 332 /* Config DSP registers */ 333 lan88xx_config_TR_regs(phydev); 334 335 return 0; 336 } 337 338 static int lan88xx_config_aneg(struct phy_device *phydev) 339 { 340 lan88xx_set_mdix(phydev); 341 342 return genphy_config_aneg(phydev); 343 } 344 345 static void lan88xx_link_change_notify(struct phy_device *phydev) 346 { 347 int temp; 348 349 /* At forced 100 F/H mode, chip may fail to set mode correctly 350 * when cable is switched between long(~50+m) and short one. 351 * As workaround, set to 10 before setting to 100 352 * at forced 100 F/H mode. 353 */ 354 if (!phydev->autoneg && phydev->speed == 100) { 355 /* disable phy interrupt */ 356 temp = phy_read(phydev, LAN88XX_INT_MASK); 357 temp &= ~LAN88XX_INT_MASK_MDINTPIN_EN_; 358 phy_write(phydev, LAN88XX_INT_MASK, temp); 359 360 temp = phy_read(phydev, MII_BMCR); 361 temp &= ~(BMCR_SPEED100 | BMCR_SPEED1000); 362 phy_write(phydev, MII_BMCR, temp); /* set to 10 first */ 363 temp |= BMCR_SPEED100; 364 phy_write(phydev, MII_BMCR, temp); /* set to 100 later */ 365 366 /* clear pending interrupt generated while workaround */ 367 temp = phy_read(phydev, LAN88XX_INT_STS); 368 369 /* enable phy interrupt back */ 370 temp = phy_read(phydev, LAN88XX_INT_MASK); 371 temp |= LAN88XX_INT_MASK_MDINTPIN_EN_; 372 phy_write(phydev, LAN88XX_INT_MASK, temp); 373 } 374 } 375 376 static struct phy_driver microchip_phy_driver[] = { 377 { 378 .phy_id = 0x0007c132, 379 /* This mask (0xfffffff2) is to differentiate from 380 * LAN8742 (phy_id 0x0007c130 and 0x0007c131) 381 * and allows future phy_id revisions. 382 */ 383 .phy_id_mask = 0xfffffff2, 384 .name = "Microchip LAN88xx", 385 386 /* PHY_GBIT_FEATURES */ 387 388 .probe = lan88xx_probe, 389 .remove = lan88xx_remove, 390 391 .config_init = lan88xx_config_init, 392 .config_aneg = lan88xx_config_aneg, 393 .link_change_notify = lan88xx_link_change_notify, 394 395 .config_intr = lan88xx_phy_config_intr, 396 .handle_interrupt = lan88xx_handle_interrupt, 397 398 .suspend = lan88xx_suspend, 399 .resume = genphy_resume, 400 .set_wol = lan88xx_set_wol, 401 .read_page = lan88xx_read_page, 402 .write_page = lan88xx_write_page, 403 } }; 404 405 module_phy_driver(microchip_phy_driver); 406 407 static struct mdio_device_id __maybe_unused microchip_tbl[] = { 408 { 0x0007c132, 0xfffffff2 }, 409 { } 410 }; 411 412 MODULE_DEVICE_TABLE(mdio, microchip_tbl); 413 414 MODULE_AUTHOR(DRIVER_AUTHOR); 415 MODULE_DESCRIPTION(DRIVER_DESC); 416 MODULE_LICENSE("GPL"); 417