net: lan78xx: fix accessing the LAN7800's internal phy specific registers from the MAC driver

Move the LAN7800 internal phy (phy ID 0x0007c132) specific register
accesses to the phy driver (microch

net: lan78xx: fix accessing the LAN7800's internal phy specific registers from the MAC driver

Move the LAN7800 internal phy (phy ID 0x0007c132) specific register
accesses to the phy driver (microchip.c).

Fix the error reported by Enguerrand de Ribaucourt in December 2022,
"Some operations during the cable switch workaround modify the register
LAN88XX_INT_MASK of the PHY. However, this register is specific to the
LAN8835 PHY. For instance, if a DP8322I PHY is connected to the LAN7801,
that register (0x19), corresponds to the LED and MAC address
configuration, resulting in unapropriate behavior."

I did not test with the DP8322I PHY, but I tested with an EVB-LAN7800
with the internal PHY.

Fixes: 14437e3fa284 ("lan78xx: workaround of forced 100 Full/Half duplex mode error")
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230301154307.30438-1-yuiko.oshino@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

net: phy: microchip: add comments for the modified LAN88xx phy ID mask.

add comments for the updated LAN88xx phy ID mask in the previous patch.

Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.c

net: phy: microchip: add comments for the modified LAN88xx phy ID mask.

add comments for the updated LAN88xx phy ID mask in the previous patch.

Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

net: phy: microchip: update LAN88xx phy ID and phy ID mask.

update LAN88xx phy ID and phy ID mask because the existing code conflicts with the LAN8742 phy.

The current phy IDs on the available hard

net: phy: microchip: update LAN88xx phy ID and phy ID mask.

update LAN88xx phy ID and phy ID mask because the existing code conflicts with the LAN8742 phy.

The current phy IDs on the available hardware.
LAN8742 0x0007C130, 0x0007C131
LAN88xx 0x0007C132

Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: microchip: remove the use of .ack_interrupt()

In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where i

net: phy: microchip: remove the use of .ack_interrupt()

In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.

This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.

Cc: Nisar Sayed <Nisar.Sayed@microchip.com>
Cc: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

net: phy: microchip: implement generic .handle_interrupt() callback

In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or

net: phy: microchip: implement generic .handle_interrupt() callback

In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.

Cc: Nisar Sayed <Nisar.Sayed@microchip.com>
Cc: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

net: phy: remove calls to genphy_config_init

Supported PHY features are either auto-detected or explicitly set.
In both cases calling genphy_config_init isn't needed. All that
genphy_config_init doe

net: phy: remove calls to genphy_config_init

Supported PHY features are either auto-detected or explicitly set.
In both cases calling genphy_config_init isn't needed. All that
genphy_config_init does is removing features that are set as
supported but can't be auto-detected. Basically it duplicates the
code in genphy_read_abilities. Therefore remove such calls from
all PHY drivers.

v2:
- remove call also from new adin PHY driver
v3:
- pass NULL as config_init function pointer for dp83848

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: switch drivers to use dynamic feature detection

Recently genphy_read_abilities() has been added that dynamically detects
clause 22 PHY abilities. I *think* this detection should work with

net: phy: switch drivers to use dynamic feature detection

Recently genphy_read_abilities() has been added that dynamically detects
clause 22 PHY abilities. I *think* this detection should work with all
supported PHY's, at least for the ones with basic features sets, i.e.
PHY_BASIC_FEATURES and PHY_GBIT_FEATURES. So let's remove setting these
features explicitly and rely on phylib feature detection.

I don't have access to most of these PHY's, therefore I'd appreciate
regression testing.

v2:
- make the feature constant a comment so that readers know which
features are supported by the respective PHY

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: Convert some PHY and MDIO driver files to SPDX headers

Where the license text and the MODULE_LICENSE() value agree, convert
to using an SPDX header, removing the license text.

Signed-off-

net: phy: Convert some PHY and MDIO driver files to SPDX headers

Where the license text and the MODULE_LICENSE() value agree, convert
to using an SPDX header, removing the license text.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: remove flag PHY_HAS_INTERRUPT from driver configs

Now that flag PHY_HAS_INTERRUPT has been replaced with a check for
callbacks config_intr and ack_interrupt, we can remove setting this
fla

net: phy: remove flag PHY_HAS_INTERRUPT from driver configs

Now that flag PHY_HAS_INTERRUPT has been replaced with a check for
callbacks config_intr and ack_interrupt, we can remove setting this
flag from all driver configs.
Last but not least remove flag PHY_HAS_INTERRUPT completely.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: Add phydev_warn()

Not all new style LINK_MODE bits can be converted into old style
SUPPORTED bits. We need to warn when such a conversion is attempted.
Add a helper for this.

Convert all

net: phy: Add phydev_warn()

Not all new style LINK_MODE bits can be converted into old style
SUPPORTED bits. We need to warn when such a conversion is attempted.
Add a helper for this.

Convert all pr_warn() calls to phydev_warn() where possible.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

lan78xx: Read LED states from Device Tree

Add support for DT property "microchip,led-modes", a vector of zero
to four cells (u32s) in the range 0-15, each of which sets the mode
for one of the LEDs.

lan78xx: Read LED states from Device Tree

Add support for DT property "microchip,led-modes", a vector of zero
to four cells (u32s) in the range 0-15, each of which sets the mode
for one of the LEDs. Some possible values are:

0=link/activity 1=link1000/activity
2=link100/activity 3=link10/activity
4=link100/1000/activity 5=link10/1000/activity
6=link10/100/activity 14=off 15=on

These values are given symbolic constants in a dt-bindings header.

Also use the presence of the DT property to indicate that the
LEDs should be enabled - necessary in the event that no valid OTP
or EEPROM is available.

Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

lan78xx: PHY DSP registers initialization to address EEE link drop issues with long cables

The patch is to configure DSP registers of PHY device
to handle Gbe-EEE failures with >40m cable length.

F

lan78xx: PHY DSP registers initialization to address EEE link drop issues with long cables

The patch is to configure DSP registers of PHY device
to handle Gbe-EEE failures with >40m cable length.

Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Raghuram Chary J <raghuramchary.jallipalli@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: remove generic settings for callbacks config_aneg and read_status from drivers

Remove generic settings for callbacks config_aneg and read_status
from drivers.

Signed-off-by: Heiner Kallwe

net: phy: remove generic settings for callbacks config_aneg and read_status from drivers

Remove generic settings for callbacks config_aneg and read_status
from drivers.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: Remove residual magic from PHY drivers

commit fa8cddaf903c ("net phylib: Remove unnecessary condition check in phy")
removed the only place where the PHY flag PHY_HAS_MAGICANEG was
checked

net: phy: Remove residual magic from PHY drivers

commit fa8cddaf903c ("net phylib: Remove unnecessary condition check in phy")
removed the only place where the PHY flag PHY_HAS_MAGICANEG was
checked. But it left the flag being set in the drivers. Remove the flag.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: switch remaining users to phy_(read|write)_mmd()

Switch everyone over to using phy_read_mmd() and phy_write_mmd() now
that they are able to handle both Clause 22 indirect addressing and
Cl

net: phy: switch remaining users to phy_(read|write)_mmd()

Switch everyone over to using phy_read_mmd() and phy_write_mmd() now
that they are able to handle both Clause 22 indirect addressing and
Clause 45 direct addressing methods to the MMD registers.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: phy drivers should not set SUPPORTED_[Asym_]Pause

Instead of having individual PHY drivers set the SUPPORTED_Pause and
SUPPORTED_Asym_Pause flags, phylib itself should set those flags,
unl

net: phy: phy drivers should not set SUPPORTED_[Asym_]Pause

Instead of having individual PHY drivers set the SUPPORTED_Pause and
SUPPORTED_Asym_Pause flags, phylib itself should set those flags,
unless there is a hardware erratum or other special case. During
autonegotiation, the PHYs will determine whether to enable pause
frame support.

Pause frames are a feature that is supported by the MAC. It is the MAC
that generates the frames and that processes them. The PHY can only be
configured to allow them to pass through.

This commit also effectively reverts the recently applied c7a61319
("net: phy: dp83848: Support ethernet pause frames").

So the new process is:

1) Unless the PHY driver overrides it, phylib sets the SUPPORTED_Pause
and SUPPORTED_AsymPause bits in phydev->supported. This indicates that
the PHY supports pause frames.

2) The MAC driver checks phydev->supported before it calls phy_start().
If (SUPPORTED_Pause | SUPPORTED_AsymPause) is set, then the MAC driver
sets those bits in phydev->advertising, if it wants to enable pause
frame support.

3) When the link state changes, the MAC driver checks phydev->pause and
phydev->asym_pause, If the bits are set, then it enables the corresponding
features in the MAC. The algorithm is:

if (phydev->pause)
The MAC should be programmed to receive and honor
pause frames it receives, i.e. enable receive flow control.

if (phydev->pause != phydev->asym_pause)
The MAC should be programmed to transmit pause
frames when needed, i.e. enable transmit flow control.

Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: Fix the mdix_ctrl changes

PHY drivers to have an eth_tp_mdix_ctrl to indicate what is the configured
MDI setting, and read eth_tp_mdi to indicate what is the current status,

Add new param

net: phy: Fix the mdix_ctrl changes

PHY drivers to have an eth_tp_mdix_ctrl to indicate what is the configured
MDI setting, and read eth_tp_mdi to indicate what is the current status,

Add new parameter mdix_ctrl in phy_device structure and fix driver.

Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

lan78xx: relocate mdix setting to phy driver

Relocate mdix code to phy driver to be called at config_init().

Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Reviewed-by: Florian Fainelli <f.

lan78xx: relocate mdix setting to phy driver

Relocate mdix code to phy driver to be called at config_init().

Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

phy: mark lan88xx_suspend() static

We get 1 warning when building kernel with W=1:
drivers/net/phy/microchip.c:58:5: warning: no previous prototype for 'lan88xx_suspend' [-Wmissing-prototypes]

In f

phy: mark lan88xx_suspend() static

We get 1 warning when building kernel with W=1:
drivers/net/phy/microchip.c:58:5: warning: no previous prototype for 'lan88xx_suspend' [-Wmissing-prototypes]

In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
so this patch marks this function with 'static'.

Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

phy: Centralize setting driver module owner

Rather than have each driver set the driver owner field, do it once in
the core code. This will also help with later changes, when the device
structure wi

phy: Centralize setting driver module owner

Rather than have each driver set the driver owner field, do it once in
the core code. This will also help with later changes, when the device
structure will move.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

phy: Add an mdio_device structure

Not all devices attached to an MDIO bus are phys. So add an
mdio_device structure to represent the generic parts of an mdio
device, and place this structure into th

phy: Add an mdio_device structure

Not all devices attached to an MDIO bus are phys. So add an
mdio_device structure to represent the generic parts of an mdio
device, and place this structure into the phy_device.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

phy: phy_{read|write}_mmd_indirect: get addr from phydev

The address of the device can be determined from the phydev structure,
rather than passing it as a parameter.

Signed-off-by: Andrew Lunn <an

phy: phy_{read|write}_mmd_indirect: get addr from phydev

The address of the device can be determined from the phydev structure,
rather than passing it as a parameter.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

add microchip LAN88xx phy driver

Add Microchip LAN88XX phy driver for phylib.

Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: remove calls to genphy_config_init

Supported PHY features are either auto-detected or explicitly set.
In both cases calling genphy_config_init isn't needed. All that
genphy

net: phy: remove calls to genphy_config_init

Supported PHY features are either auto-detected or explicitly set.
In both cases calling genphy_config_init isn't needed. All that
genphy_config_init does is removing features that are set as
supported but can't be auto-detected. Basically it duplicates the
code in genphy_read_abilities. Therefore remove such calls from
all PHY drivers.

v2:
- remove call also from new adin PHY driver
v3:
- pass NULL as config_init function pointer for dp83848

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: switch drivers to use dynamic feature detection

Recently genphy_read_abilities() has been added that dynamically detects
clause 22 PHY abilities. I *think* this detection shoul

net: phy: switch drivers to use dynamic feature detection

Recently genphy_read_abilities() has been added that dynamically detects
clause 22 PHY abilities. I *think* this detection should work with all
supported PHY's, at least for the ones with basic features sets, i.e.
PHY_BASIC_FEATURES and PHY_GBIT_FEATURES. So let's remove setting these
features explicitly and rely on phylib feature detection.

I don't have access to most of these PHY's, therefore I'd appreciate
regression testing.

v2:
- make the feature constant a comment so that readers know which
features are supported by the respective PHY

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...