1 // SPDX-License-Identifier: GPL-2.0 2 /* Driver for the Texas Instruments DP83867 PHY 3 * 4 * Copyright (C) 2015 Texas Instruments Inc. 5 */ 6 7 #include <linux/ethtool.h> 8 #include <linux/kernel.h> 9 #include <linux/mii.h> 10 #include <linux/module.h> 11 #include <linux/of.h> 12 #include <linux/phy.h> 13 #include <linux/delay.h> 14 #include <linux/netdevice.h> 15 #include <linux/etherdevice.h> 16 #include <linux/bitfield.h> 17 18 #include <dt-bindings/net/ti-dp83867.h> 19 20 #define DP83867_PHY_ID 0x2000a231 21 #define DP83867_DEVADDR 0x1f 22 23 #define MII_DP83867_PHYCTRL 0x10 24 #define MII_DP83867_PHYSTS 0x11 25 #define MII_DP83867_MICR 0x12 26 #define MII_DP83867_ISR 0x13 27 #define DP83867_CFG2 0x14 28 #define DP83867_CFG3 0x1e 29 #define DP83867_CTRL 0x1f 30 31 /* Extended Registers */ 32 #define DP83867_FLD_THR_CFG 0x002e 33 #define DP83867_CFG4 0x0031 34 #define DP83867_CFG4_SGMII_ANEG_MASK (BIT(5) | BIT(6)) 35 #define DP83867_CFG4_SGMII_ANEG_TIMER_11MS (3 << 5) 36 #define DP83867_CFG4_SGMII_ANEG_TIMER_800US (2 << 5) 37 #define DP83867_CFG4_SGMII_ANEG_TIMER_2US (1 << 5) 38 #define DP83867_CFG4_SGMII_ANEG_TIMER_16MS (0 << 5) 39 40 #define DP83867_RGMIICTL 0x0032 41 #define DP83867_STRAP_STS1 0x006E 42 #define DP83867_STRAP_STS2 0x006f 43 #define DP83867_RGMIIDCTL 0x0086 44 #define DP83867_RXFCFG 0x0134 45 #define DP83867_RXFPMD1 0x0136 46 #define DP83867_RXFPMD2 0x0137 47 #define DP83867_RXFPMD3 0x0138 48 #define DP83867_RXFSOP1 0x0139 49 #define DP83867_RXFSOP2 0x013A 50 #define DP83867_RXFSOP3 0x013B 51 #define DP83867_IO_MUX_CFG 0x0170 52 #define DP83867_SGMIICTL 0x00D3 53 #define DP83867_10M_SGMII_CFG 0x016F 54 #define DP83867_10M_SGMII_RATE_ADAPT_MASK BIT(7) 55 56 #define DP83867_SW_RESET BIT(15) 57 #define DP83867_SW_RESTART BIT(14) 58 59 /* MICR Interrupt bits */ 60 #define MII_DP83867_MICR_AN_ERR_INT_EN BIT(15) 61 #define MII_DP83867_MICR_SPEED_CHNG_INT_EN BIT(14) 62 #define MII_DP83867_MICR_DUP_MODE_CHNG_INT_EN BIT(13) 63 #define MII_DP83867_MICR_PAGE_RXD_INT_EN BIT(12) 64 #define MII_DP83867_MICR_AUTONEG_COMP_INT_EN BIT(11) 65 #define MII_DP83867_MICR_LINK_STS_CHNG_INT_EN BIT(10) 66 #define MII_DP83867_MICR_FALSE_CARRIER_INT_EN BIT(8) 67 #define MII_DP83867_MICR_SLEEP_MODE_CHNG_INT_EN BIT(4) 68 #define MII_DP83867_MICR_WOL_INT_EN BIT(3) 69 #define MII_DP83867_MICR_XGMII_ERR_INT_EN BIT(2) 70 #define MII_DP83867_MICR_POL_CHNG_INT_EN BIT(1) 71 #define MII_DP83867_MICR_JABBER_INT_EN BIT(0) 72 73 /* RGMIICTL bits */ 74 #define DP83867_RGMII_TX_CLK_DELAY_EN BIT(1) 75 #define DP83867_RGMII_RX_CLK_DELAY_EN BIT(0) 76 77 /* SGMIICTL bits */ 78 #define DP83867_SGMII_TYPE BIT(14) 79 80 /* RXFCFG bits*/ 81 #define DP83867_WOL_MAGIC_EN BIT(0) 82 #define DP83867_WOL_BCAST_EN BIT(2) 83 #define DP83867_WOL_UCAST_EN BIT(4) 84 #define DP83867_WOL_SEC_EN BIT(5) 85 #define DP83867_WOL_ENH_MAC BIT(7) 86 87 /* STRAP_STS1 bits */ 88 #define DP83867_STRAP_STS1_RESERVED BIT(11) 89 90 /* STRAP_STS2 bits */ 91 #define DP83867_STRAP_STS2_CLK_SKEW_TX_MASK GENMASK(6, 4) 92 #define DP83867_STRAP_STS2_CLK_SKEW_TX_SHIFT 4 93 #define DP83867_STRAP_STS2_CLK_SKEW_RX_MASK GENMASK(2, 0) 94 #define DP83867_STRAP_STS2_CLK_SKEW_RX_SHIFT 0 95 #define DP83867_STRAP_STS2_CLK_SKEW_NONE BIT(2) 96 #define DP83867_STRAP_STS2_STRAP_FLD BIT(10) 97 98 /* PHY CTRL bits */ 99 #define DP83867_PHYCR_TX_FIFO_DEPTH_SHIFT 14 100 #define DP83867_PHYCR_RX_FIFO_DEPTH_SHIFT 12 101 #define DP83867_PHYCR_FIFO_DEPTH_MAX 0x03 102 #define DP83867_PHYCR_TX_FIFO_DEPTH_MASK GENMASK(15, 14) 103 #define DP83867_PHYCR_RX_FIFO_DEPTH_MASK GENMASK(13, 12) 104 #define DP83867_PHYCR_RESERVED_MASK BIT(11) 105 #define DP83867_PHYCR_FORCE_LINK_GOOD BIT(10) 106 107 /* RGMIIDCTL bits */ 108 #define DP83867_RGMII_TX_CLK_DELAY_MAX 0xf 109 #define DP83867_RGMII_TX_CLK_DELAY_SHIFT 4 110 #define DP83867_RGMII_TX_CLK_DELAY_INV (DP83867_RGMII_TX_CLK_DELAY_MAX + 1) 111 #define DP83867_RGMII_RX_CLK_DELAY_MAX 0xf 112 #define DP83867_RGMII_RX_CLK_DELAY_SHIFT 0 113 #define DP83867_RGMII_RX_CLK_DELAY_INV (DP83867_RGMII_RX_CLK_DELAY_MAX + 1) 114 115 /* IO_MUX_CFG bits */ 116 #define DP83867_IO_MUX_CFG_IO_IMPEDANCE_MASK 0x1f 117 #define DP83867_IO_MUX_CFG_IO_IMPEDANCE_MAX 0x0 118 #define DP83867_IO_MUX_CFG_IO_IMPEDANCE_MIN 0x1f 119 #define DP83867_IO_MUX_CFG_CLK_O_DISABLE BIT(6) 120 #define DP83867_IO_MUX_CFG_CLK_O_SEL_MASK (0x1f << 8) 121 #define DP83867_IO_MUX_CFG_CLK_O_SEL_SHIFT 8 122 123 /* PHY STS bits */ 124 #define DP83867_PHYSTS_1000 BIT(15) 125 #define DP83867_PHYSTS_100 BIT(14) 126 #define DP83867_PHYSTS_DUPLEX BIT(13) 127 #define DP83867_PHYSTS_LINK BIT(10) 128 129 /* CFG2 bits */ 130 #define DP83867_DOWNSHIFT_EN (BIT(8) | BIT(9)) 131 #define DP83867_DOWNSHIFT_ATTEMPT_MASK (BIT(10) | BIT(11)) 132 #define DP83867_DOWNSHIFT_1_COUNT_VAL 0 133 #define DP83867_DOWNSHIFT_2_COUNT_VAL 1 134 #define DP83867_DOWNSHIFT_4_COUNT_VAL 2 135 #define DP83867_DOWNSHIFT_8_COUNT_VAL 3 136 #define DP83867_DOWNSHIFT_1_COUNT 1 137 #define DP83867_DOWNSHIFT_2_COUNT 2 138 #define DP83867_DOWNSHIFT_4_COUNT 4 139 #define DP83867_DOWNSHIFT_8_COUNT 8 140 141 /* CFG3 bits */ 142 #define DP83867_CFG3_INT_OE BIT(7) 143 #define DP83867_CFG3_ROBUST_AUTO_MDIX BIT(9) 144 145 /* CFG4 bits */ 146 #define DP83867_CFG4_PORT_MIRROR_EN BIT(0) 147 148 /* FLD_THR_CFG */ 149 #define DP83867_FLD_THR_CFG_ENERGY_LOST_THR_MASK 0x7 150 151 enum { 152 DP83867_PORT_MIRROING_KEEP, 153 DP83867_PORT_MIRROING_EN, 154 DP83867_PORT_MIRROING_DIS, 155 }; 156 157 struct dp83867_private { 158 u32 rx_id_delay; 159 u32 tx_id_delay; 160 u32 tx_fifo_depth; 161 u32 rx_fifo_depth; 162 int io_impedance; 163 int port_mirroring; 164 bool rxctrl_strap_quirk; 165 bool set_clk_output; 166 u32 clk_output_sel; 167 bool sgmii_ref_clk_en; 168 }; 169 170 static int dp83867_ack_interrupt(struct phy_device *phydev) 171 { 172 int err = phy_read(phydev, MII_DP83867_ISR); 173 174 if (err < 0) 175 return err; 176 177 return 0; 178 } 179 180 static int dp83867_set_wol(struct phy_device *phydev, 181 struct ethtool_wolinfo *wol) 182 { 183 struct net_device *ndev = phydev->attached_dev; 184 u16 val_rxcfg, val_micr; 185 u8 *mac; 186 187 val_rxcfg = phy_read_mmd(phydev, DP83867_DEVADDR, DP83867_RXFCFG); 188 val_micr = phy_read(phydev, MII_DP83867_MICR); 189 190 if (wol->wolopts & (WAKE_MAGIC | WAKE_MAGICSECURE | WAKE_UCAST | 191 WAKE_BCAST)) { 192 val_rxcfg |= DP83867_WOL_ENH_MAC; 193 val_micr |= MII_DP83867_MICR_WOL_INT_EN; 194 195 if (wol->wolopts & WAKE_MAGIC) { 196 mac = (u8 *)ndev->dev_addr; 197 198 if (!is_valid_ether_addr(mac)) 199 return -EINVAL; 200 201 phy_write_mmd(phydev, DP83867_DEVADDR, DP83867_RXFPMD1, 202 (mac[1] << 8 | mac[0])); 203 phy_write_mmd(phydev, DP83867_DEVADDR, DP83867_RXFPMD2, 204 (mac[3] << 8 | mac[2])); 205 phy_write_mmd(phydev, DP83867_DEVADDR, DP83867_RXFPMD3, 206 (mac[5] << 8 | mac[4])); 207 208 val_rxcfg |= DP83867_WOL_MAGIC_EN; 209 } else { 210 val_rxcfg &= ~DP83867_WOL_MAGIC_EN; 211 } 212 213 if (wol->wolopts & WAKE_MAGICSECURE) { 214 phy_write_mmd(phydev, DP83867_DEVADDR, DP83867_RXFSOP1, 215 (wol->sopass[1] << 8) | wol->sopass[0]); 216 phy_write_mmd(phydev, DP83867_DEVADDR, DP83867_RXFSOP2, 217 (wol->sopass[3] << 8) | wol->sopass[2]); 218 phy_write_mmd(phydev, DP83867_DEVADDR, DP83867_RXFSOP3, 219 (wol->sopass[5] << 8) | wol->sopass[4]); 220 221 val_rxcfg |= DP83867_WOL_SEC_EN; 222 } else { 223 val_rxcfg &= ~DP83867_WOL_SEC_EN; 224 } 225 226 if (wol->wolopts & WAKE_UCAST) 227 val_rxcfg |= DP83867_WOL_UCAST_EN; 228 else 229 val_rxcfg &= ~DP83867_WOL_UCAST_EN; 230 231 if (wol->wolopts & WAKE_BCAST) 232 val_rxcfg |= DP83867_WOL_BCAST_EN; 233 else 234 val_rxcfg &= ~DP83867_WOL_BCAST_EN; 235 } else { 236 val_rxcfg &= ~DP83867_WOL_ENH_MAC; 237 val_micr &= ~MII_DP83867_MICR_WOL_INT_EN; 238 } 239 240 phy_write_mmd(phydev, DP83867_DEVADDR, DP83867_RXFCFG, val_rxcfg); 241 phy_write(phydev, MII_DP83867_MICR, val_micr); 242 243 return 0; 244 } 245 246 static void dp83867_get_wol(struct phy_device *phydev, 247 struct ethtool_wolinfo *wol) 248 { 249 u16 value, sopass_val; 250 251 wol->supported = (WAKE_UCAST | WAKE_BCAST | WAKE_MAGIC | 252 WAKE_MAGICSECURE); 253 wol->wolopts = 0; 254 255 value = phy_read_mmd(phydev, DP83867_DEVADDR, DP83867_RXFCFG); 256 257 if (value & DP83867_WOL_UCAST_EN) 258 wol->wolopts |= WAKE_UCAST; 259 260 if (value & DP83867_WOL_BCAST_EN) 261 wol->wolopts |= WAKE_BCAST; 262 263 if (value & DP83867_WOL_MAGIC_EN) 264 wol->wolopts |= WAKE_MAGIC; 265 266 if (value & DP83867_WOL_SEC_EN) { 267 sopass_val = phy_read_mmd(phydev, DP83867_DEVADDR, 268 DP83867_RXFSOP1); 269 wol->sopass[0] = (sopass_val & 0xff); 270 wol->sopass[1] = (sopass_val >> 8); 271 272 sopass_val = phy_read_mmd(phydev, DP83867_DEVADDR, 273 DP83867_RXFSOP2); 274 wol->sopass[2] = (sopass_val & 0xff); 275 wol->sopass[3] = (sopass_val >> 8); 276 277 sopass_val = phy_read_mmd(phydev, DP83867_DEVADDR, 278 DP83867_RXFSOP3); 279 wol->sopass[4] = (sopass_val & 0xff); 280 wol->sopass[5] = (sopass_val >> 8); 281 282 wol->wolopts |= WAKE_MAGICSECURE; 283 } 284 285 if (!(value & DP83867_WOL_ENH_MAC)) 286 wol->wolopts = 0; 287 } 288 289 static int dp83867_config_intr(struct phy_device *phydev) 290 { 291 int micr_status, err; 292 293 if (phydev->interrupts == PHY_INTERRUPT_ENABLED) { 294 err = dp83867_ack_interrupt(phydev); 295 if (err) 296 return err; 297 298 micr_status = phy_read(phydev, MII_DP83867_MICR); 299 if (micr_status < 0) 300 return micr_status; 301 302 micr_status |= 303 (MII_DP83867_MICR_AN_ERR_INT_EN | 304 MII_DP83867_MICR_SPEED_CHNG_INT_EN | 305 MII_DP83867_MICR_AUTONEG_COMP_INT_EN | 306 MII_DP83867_MICR_LINK_STS_CHNG_INT_EN | 307 MII_DP83867_MICR_DUP_MODE_CHNG_INT_EN | 308 MII_DP83867_MICR_SLEEP_MODE_CHNG_INT_EN); 309 310 err = phy_write(phydev, MII_DP83867_MICR, micr_status); 311 } else { 312 micr_status = 0x0; 313 err = phy_write(phydev, MII_DP83867_MICR, micr_status); 314 if (err) 315 return err; 316 317 err = dp83867_ack_interrupt(phydev); 318 } 319 320 return err; 321 } 322 323 static irqreturn_t dp83867_handle_interrupt(struct phy_device *phydev) 324 { 325 int irq_status, irq_enabled; 326 327 irq_status = phy_read(phydev, MII_DP83867_ISR); 328 if (irq_status < 0) { 329 phy_error(phydev); 330 return IRQ_NONE; 331 } 332 333 irq_enabled = phy_read(phydev, MII_DP83867_MICR); 334 if (irq_enabled < 0) { 335 phy_error(phydev); 336 return IRQ_NONE; 337 } 338 339 if (!(irq_status & irq_enabled)) 340 return IRQ_NONE; 341 342 phy_trigger_machine(phydev); 343 344 return IRQ_HANDLED; 345 } 346 347 static int dp83867_read_status(struct phy_device *phydev) 348 { 349 int status = phy_read(phydev, MII_DP83867_PHYSTS); 350 int ret; 351 352 ret = genphy_read_status(phydev); 353 if (ret) 354 return ret; 355 356 if (status < 0) 357 return status; 358 359 if (status & DP83867_PHYSTS_DUPLEX) 360 phydev->duplex = DUPLEX_FULL; 361 else 362 phydev->duplex = DUPLEX_HALF; 363 364 if (status & DP83867_PHYSTS_1000) 365 phydev->speed = SPEED_1000; 366 else if (status & DP83867_PHYSTS_100) 367 phydev->speed = SPEED_100; 368 else 369 phydev->speed = SPEED_10; 370 371 return 0; 372 } 373 374 static int dp83867_get_downshift(struct phy_device *phydev, u8 *data) 375 { 376 int val, cnt, enable, count; 377 378 val = phy_read(phydev, DP83867_CFG2); 379 if (val < 0) 380 return val; 381 382 enable = FIELD_GET(DP83867_DOWNSHIFT_EN, val); 383 cnt = FIELD_GET(DP83867_DOWNSHIFT_ATTEMPT_MASK, val); 384 385 switch (cnt) { 386 case DP83867_DOWNSHIFT_1_COUNT_VAL: 387 count = DP83867_DOWNSHIFT_1_COUNT; 388 break; 389 case DP83867_DOWNSHIFT_2_COUNT_VAL: 390 count = DP83867_DOWNSHIFT_2_COUNT; 391 break; 392 case DP83867_DOWNSHIFT_4_COUNT_VAL: 393 count = DP83867_DOWNSHIFT_4_COUNT; 394 break; 395 case DP83867_DOWNSHIFT_8_COUNT_VAL: 396 count = DP83867_DOWNSHIFT_8_COUNT; 397 break; 398 default: 399 return -EINVAL; 400 } 401 402 *data = enable ? count : DOWNSHIFT_DEV_DISABLE; 403 404 return 0; 405 } 406 407 static int dp83867_set_downshift(struct phy_device *phydev, u8 cnt) 408 { 409 int val, count; 410 411 if (cnt > DP83867_DOWNSHIFT_8_COUNT) 412 return -E2BIG; 413 414 if (!cnt) 415 return phy_clear_bits(phydev, DP83867_CFG2, 416 DP83867_DOWNSHIFT_EN); 417 418 switch (cnt) { 419 case DP83867_DOWNSHIFT_1_COUNT: 420 count = DP83867_DOWNSHIFT_1_COUNT_VAL; 421 break; 422 case DP83867_DOWNSHIFT_2_COUNT: 423 count = DP83867_DOWNSHIFT_2_COUNT_VAL; 424 break; 425 case DP83867_DOWNSHIFT_4_COUNT: 426 count = DP83867_DOWNSHIFT_4_COUNT_VAL; 427 break; 428 case DP83867_DOWNSHIFT_8_COUNT: 429 count = DP83867_DOWNSHIFT_8_COUNT_VAL; 430 break; 431 default: 432 phydev_err(phydev, 433 "Downshift count must be 1, 2, 4 or 8\n"); 434 return -EINVAL; 435 } 436 437 val = DP83867_DOWNSHIFT_EN; 438 val |= FIELD_PREP(DP83867_DOWNSHIFT_ATTEMPT_MASK, count); 439 440 return phy_modify(phydev, DP83867_CFG2, 441 DP83867_DOWNSHIFT_EN | DP83867_DOWNSHIFT_ATTEMPT_MASK, 442 val); 443 } 444 445 static int dp83867_get_tunable(struct phy_device *phydev, 446 struct ethtool_tunable *tuna, void *data) 447 { 448 switch (tuna->id) { 449 case ETHTOOL_PHY_DOWNSHIFT: 450 return dp83867_get_downshift(phydev, data); 451 default: 452 return -EOPNOTSUPP; 453 } 454 } 455 456 static int dp83867_set_tunable(struct phy_device *phydev, 457 struct ethtool_tunable *tuna, const void *data) 458 { 459 switch (tuna->id) { 460 case ETHTOOL_PHY_DOWNSHIFT: 461 return dp83867_set_downshift(phydev, *(const u8 *)data); 462 default: 463 return -EOPNOTSUPP; 464 } 465 } 466 467 static int dp83867_config_port_mirroring(struct phy_device *phydev) 468 { 469 struct dp83867_private *dp83867 = 470 (struct dp83867_private *)phydev->priv; 471 472 if (dp83867->port_mirroring == DP83867_PORT_MIRROING_EN) 473 phy_set_bits_mmd(phydev, DP83867_DEVADDR, DP83867_CFG4, 474 DP83867_CFG4_PORT_MIRROR_EN); 475 else 476 phy_clear_bits_mmd(phydev, DP83867_DEVADDR, DP83867_CFG4, 477 DP83867_CFG4_PORT_MIRROR_EN); 478 return 0; 479 } 480 481 static int dp83867_verify_rgmii_cfg(struct phy_device *phydev) 482 { 483 struct dp83867_private *dp83867 = phydev->priv; 484 485 /* Existing behavior was to use default pin strapping delay in rgmii 486 * mode, but rgmii should have meant no delay. Warn existing users. 487 */ 488 if (phydev->interface == PHY_INTERFACE_MODE_RGMII) { 489 const u16 val = phy_read_mmd(phydev, DP83867_DEVADDR, 490 DP83867_STRAP_STS2); 491 const u16 txskew = (val & DP83867_STRAP_STS2_CLK_SKEW_TX_MASK) >> 492 DP83867_STRAP_STS2_CLK_SKEW_TX_SHIFT; 493 const u16 rxskew = (val & DP83867_STRAP_STS2_CLK_SKEW_RX_MASK) >> 494 DP83867_STRAP_STS2_CLK_SKEW_RX_SHIFT; 495 496 if (txskew != DP83867_STRAP_STS2_CLK_SKEW_NONE || 497 rxskew != DP83867_STRAP_STS2_CLK_SKEW_NONE) 498 phydev_warn(phydev, 499 "PHY has delays via pin strapping, but phy-mode = 'rgmii'\n" 500 "Should be 'rgmii-id' to use internal delays txskew:%x rxskew:%x\n", 501 txskew, rxskew); 502 } 503 504 /* RX delay *must* be specified if internal delay of RX is used. */ 505 if ((phydev->interface == PHY_INTERFACE_MODE_RGMII_ID || 506 phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) && 507 dp83867->rx_id_delay == DP83867_RGMII_RX_CLK_DELAY_INV) { 508 phydev_err(phydev, "ti,rx-internal-delay must be specified\n"); 509 return -EINVAL; 510 } 511 512 /* TX delay *must* be specified if internal delay of TX is used. */ 513 if ((phydev->interface == PHY_INTERFACE_MODE_RGMII_ID || 514 phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID) && 515 dp83867->tx_id_delay == DP83867_RGMII_TX_CLK_DELAY_INV) { 516 phydev_err(phydev, "ti,tx-internal-delay must be specified\n"); 517 return -EINVAL; 518 } 519 520 return 0; 521 } 522 523 #if IS_ENABLED(CONFIG_OF_MDIO) 524 static int dp83867_of_init(struct phy_device *phydev) 525 { 526 struct dp83867_private *dp83867 = phydev->priv; 527 struct device *dev = &phydev->mdio.dev; 528 struct device_node *of_node = dev->of_node; 529 int ret; 530 531 if (!of_node) 532 return -ENODEV; 533 534 /* Optional configuration */ 535 ret = of_property_read_u32(of_node, "ti,clk-output-sel", 536 &dp83867->clk_output_sel); 537 /* If not set, keep default */ 538 if (!ret) { 539 dp83867->set_clk_output = true; 540 /* Valid values are 0 to DP83867_CLK_O_SEL_REF_CLK or 541 * DP83867_CLK_O_SEL_OFF. 542 */ 543 if (dp83867->clk_output_sel > DP83867_CLK_O_SEL_REF_CLK && 544 dp83867->clk_output_sel != DP83867_CLK_O_SEL_OFF) { 545 phydev_err(phydev, "ti,clk-output-sel value %u out of range\n", 546 dp83867->clk_output_sel); 547 return -EINVAL; 548 } 549 } 550 551 if (of_property_read_bool(of_node, "ti,max-output-impedance")) 552 dp83867->io_impedance = DP83867_IO_MUX_CFG_IO_IMPEDANCE_MAX; 553 else if (of_property_read_bool(of_node, "ti,min-output-impedance")) 554 dp83867->io_impedance = DP83867_IO_MUX_CFG_IO_IMPEDANCE_MIN; 555 else 556 dp83867->io_impedance = -1; /* leave at default */ 557 558 dp83867->rxctrl_strap_quirk = of_property_read_bool(of_node, 559 "ti,dp83867-rxctrl-strap-quirk"); 560 561 dp83867->sgmii_ref_clk_en = of_property_read_bool(of_node, 562 "ti,sgmii-ref-clock-output-enable"); 563 564 dp83867->rx_id_delay = DP83867_RGMII_RX_CLK_DELAY_INV; 565 ret = of_property_read_u32(of_node, "ti,rx-internal-delay", 566 &dp83867->rx_id_delay); 567 if (!ret && dp83867->rx_id_delay > DP83867_RGMII_RX_CLK_DELAY_MAX) { 568 phydev_err(phydev, 569 "ti,rx-internal-delay value of %u out of range\n", 570 dp83867->rx_id_delay); 571 return -EINVAL; 572 } 573 574 dp83867->tx_id_delay = DP83867_RGMII_TX_CLK_DELAY_INV; 575 ret = of_property_read_u32(of_node, "ti,tx-internal-delay", 576 &dp83867->tx_id_delay); 577 if (!ret && dp83867->tx_id_delay > DP83867_RGMII_TX_CLK_DELAY_MAX) { 578 phydev_err(phydev, 579 "ti,tx-internal-delay value of %u out of range\n", 580 dp83867->tx_id_delay); 581 return -EINVAL; 582 } 583 584 if (of_property_read_bool(of_node, "enet-phy-lane-swap")) 585 dp83867->port_mirroring = DP83867_PORT_MIRROING_EN; 586 587 if (of_property_read_bool(of_node, "enet-phy-lane-no-swap")) 588 dp83867->port_mirroring = DP83867_PORT_MIRROING_DIS; 589 590 ret = of_property_read_u32(of_node, "ti,fifo-depth", 591 &dp83867->tx_fifo_depth); 592 if (ret) { 593 ret = of_property_read_u32(of_node, "tx-fifo-depth", 594 &dp83867->tx_fifo_depth); 595 if (ret) 596 dp83867->tx_fifo_depth = 597 DP83867_PHYCR_FIFO_DEPTH_4_B_NIB; 598 } 599 600 if (dp83867->tx_fifo_depth > DP83867_PHYCR_FIFO_DEPTH_MAX) { 601 phydev_err(phydev, "tx-fifo-depth value %u out of range\n", 602 dp83867->tx_fifo_depth); 603 return -EINVAL; 604 } 605 606 ret = of_property_read_u32(of_node, "rx-fifo-depth", 607 &dp83867->rx_fifo_depth); 608 if (ret) 609 dp83867->rx_fifo_depth = DP83867_PHYCR_FIFO_DEPTH_4_B_NIB; 610 611 if (dp83867->rx_fifo_depth > DP83867_PHYCR_FIFO_DEPTH_MAX) { 612 phydev_err(phydev, "rx-fifo-depth value %u out of range\n", 613 dp83867->rx_fifo_depth); 614 return -EINVAL; 615 } 616 617 return 0; 618 } 619 #else 620 static int dp83867_of_init(struct phy_device *phydev) 621 { 622 return 0; 623 } 624 #endif /* CONFIG_OF_MDIO */ 625 626 static int dp83867_probe(struct phy_device *phydev) 627 { 628 struct dp83867_private *dp83867; 629 630 dp83867 = devm_kzalloc(&phydev->mdio.dev, sizeof(*dp83867), 631 GFP_KERNEL); 632 if (!dp83867) 633 return -ENOMEM; 634 635 phydev->priv = dp83867; 636 637 return dp83867_of_init(phydev); 638 } 639 640 static int dp83867_config_init(struct phy_device *phydev) 641 { 642 struct dp83867_private *dp83867 = phydev->priv; 643 int ret, val, bs; 644 u16 delay; 645 646 /* Force speed optimization for the PHY even if it strapped */ 647 ret = phy_modify(phydev, DP83867_CFG2, DP83867_DOWNSHIFT_EN, 648 DP83867_DOWNSHIFT_EN); 649 if (ret) 650 return ret; 651 652 ret = dp83867_verify_rgmii_cfg(phydev); 653 if (ret) 654 return ret; 655 656 /* RX_DV/RX_CTRL strapped in mode 1 or mode 2 workaround */ 657 if (dp83867->rxctrl_strap_quirk) 658 phy_clear_bits_mmd(phydev, DP83867_DEVADDR, DP83867_CFG4, 659 BIT(7)); 660 661 bs = phy_read_mmd(phydev, DP83867_DEVADDR, DP83867_STRAP_STS2); 662 if (bs & DP83867_STRAP_STS2_STRAP_FLD) { 663 /* When using strap to enable FLD, the ENERGY_LOST_FLD_THR will 664 * be set to 0x2. This may causes the PHY link to be unstable - 665 * the default value 0x1 need to be restored. 666 */ 667 ret = phy_modify_mmd(phydev, DP83867_DEVADDR, 668 DP83867_FLD_THR_CFG, 669 DP83867_FLD_THR_CFG_ENERGY_LOST_THR_MASK, 670 0x1); 671 if (ret) 672 return ret; 673 } 674 675 if (phy_interface_is_rgmii(phydev) || 676 phydev->interface == PHY_INTERFACE_MODE_SGMII) { 677 val = phy_read(phydev, MII_DP83867_PHYCTRL); 678 if (val < 0) 679 return val; 680 681 val &= ~DP83867_PHYCR_TX_FIFO_DEPTH_MASK; 682 val |= (dp83867->tx_fifo_depth << 683 DP83867_PHYCR_TX_FIFO_DEPTH_SHIFT); 684 685 if (phydev->interface == PHY_INTERFACE_MODE_SGMII) { 686 val &= ~DP83867_PHYCR_RX_FIFO_DEPTH_MASK; 687 val |= (dp83867->rx_fifo_depth << 688 DP83867_PHYCR_RX_FIFO_DEPTH_SHIFT); 689 } 690 691 ret = phy_write(phydev, MII_DP83867_PHYCTRL, val); 692 if (ret) 693 return ret; 694 } 695 696 if (phy_interface_is_rgmii(phydev)) { 697 val = phy_read(phydev, MII_DP83867_PHYCTRL); 698 if (val < 0) 699 return val; 700 701 /* The code below checks if "port mirroring" N/A MODE4 has been 702 * enabled during power on bootstrap. 703 * 704 * Such N/A mode enabled by mistake can put PHY IC in some 705 * internal testing mode and disable RGMII transmission. 706 * 707 * In this particular case one needs to check STRAP_STS1 708 * register's bit 11 (marked as RESERVED). 709 */ 710 711 bs = phy_read_mmd(phydev, DP83867_DEVADDR, DP83867_STRAP_STS1); 712 if (bs & DP83867_STRAP_STS1_RESERVED) 713 val &= ~DP83867_PHYCR_RESERVED_MASK; 714 715 ret = phy_write(phydev, MII_DP83867_PHYCTRL, val); 716 if (ret) 717 return ret; 718 719 /* If rgmii mode with no internal delay is selected, we do NOT use 720 * aligned mode as one might expect. Instead we use the PHY's default 721 * based on pin strapping. And the "mode 0" default is to *use* 722 * internal delay with a value of 7 (2.00 ns). 723 * 724 * Set up RGMII delays 725 */ 726 val = phy_read_mmd(phydev, DP83867_DEVADDR, DP83867_RGMIICTL); 727 728 val &= ~(DP83867_RGMII_TX_CLK_DELAY_EN | DP83867_RGMII_RX_CLK_DELAY_EN); 729 if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) 730 val |= (DP83867_RGMII_TX_CLK_DELAY_EN | DP83867_RGMII_RX_CLK_DELAY_EN); 731 732 if (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID) 733 val |= DP83867_RGMII_TX_CLK_DELAY_EN; 734 735 if (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) 736 val |= DP83867_RGMII_RX_CLK_DELAY_EN; 737 738 phy_write_mmd(phydev, DP83867_DEVADDR, DP83867_RGMIICTL, val); 739 740 delay = 0; 741 if (dp83867->rx_id_delay != DP83867_RGMII_RX_CLK_DELAY_INV) 742 delay |= dp83867->rx_id_delay; 743 if (dp83867->tx_id_delay != DP83867_RGMII_TX_CLK_DELAY_INV) 744 delay |= dp83867->tx_id_delay << 745 DP83867_RGMII_TX_CLK_DELAY_SHIFT; 746 747 phy_write_mmd(phydev, DP83867_DEVADDR, DP83867_RGMIIDCTL, 748 delay); 749 } 750 751 /* If specified, set io impedance */ 752 if (dp83867->io_impedance >= 0) 753 phy_modify_mmd(phydev, DP83867_DEVADDR, DP83867_IO_MUX_CFG, 754 DP83867_IO_MUX_CFG_IO_IMPEDANCE_MASK, 755 dp83867->io_impedance); 756 757 if (phydev->interface == PHY_INTERFACE_MODE_SGMII) { 758 /* For support SPEED_10 in SGMII mode 759 * DP83867_10M_SGMII_RATE_ADAPT bit 760 * has to be cleared by software. That 761 * does not affect SPEED_100 and 762 * SPEED_1000. 763 */ 764 ret = phy_modify_mmd(phydev, DP83867_DEVADDR, 765 DP83867_10M_SGMII_CFG, 766 DP83867_10M_SGMII_RATE_ADAPT_MASK, 767 0); 768 if (ret) 769 return ret; 770 771 /* After reset SGMII Autoneg timer is set to 2us (bits 6 and 5 772 * are 01). That is not enough to finalize autoneg on some 773 * devices. Increase this timer duration to maximum 16ms. 774 */ 775 ret = phy_modify_mmd(phydev, DP83867_DEVADDR, 776 DP83867_CFG4, 777 DP83867_CFG4_SGMII_ANEG_MASK, 778 DP83867_CFG4_SGMII_ANEG_TIMER_16MS); 779 780 if (ret) 781 return ret; 782 783 val = phy_read_mmd(phydev, DP83867_DEVADDR, DP83867_SGMIICTL); 784 /* SGMII type is set to 4-wire mode by default. 785 * If we place appropriate property in dts (see above) 786 * switch on 6-wire mode. 787 */ 788 if (dp83867->sgmii_ref_clk_en) 789 val |= DP83867_SGMII_TYPE; 790 else 791 val &= ~DP83867_SGMII_TYPE; 792 phy_write_mmd(phydev, DP83867_DEVADDR, DP83867_SGMIICTL, val); 793 } 794 795 val = phy_read(phydev, DP83867_CFG3); 796 /* Enable Interrupt output INT_OE in CFG3 register */ 797 if (phy_interrupt_is_valid(phydev)) 798 val |= DP83867_CFG3_INT_OE; 799 800 val |= DP83867_CFG3_ROBUST_AUTO_MDIX; 801 phy_write(phydev, DP83867_CFG3, val); 802 803 if (dp83867->port_mirroring != DP83867_PORT_MIRROING_KEEP) 804 dp83867_config_port_mirroring(phydev); 805 806 /* Clock output selection if muxing property is set */ 807 if (dp83867->set_clk_output) { 808 u16 mask = DP83867_IO_MUX_CFG_CLK_O_DISABLE; 809 810 if (dp83867->clk_output_sel == DP83867_CLK_O_SEL_OFF) { 811 val = DP83867_IO_MUX_CFG_CLK_O_DISABLE; 812 } else { 813 mask |= DP83867_IO_MUX_CFG_CLK_O_SEL_MASK; 814 val = dp83867->clk_output_sel << 815 DP83867_IO_MUX_CFG_CLK_O_SEL_SHIFT; 816 } 817 818 phy_modify_mmd(phydev, DP83867_DEVADDR, DP83867_IO_MUX_CFG, 819 mask, val); 820 } 821 822 return 0; 823 } 824 825 static int dp83867_phy_reset(struct phy_device *phydev) 826 { 827 int err; 828 829 err = phy_write(phydev, DP83867_CTRL, DP83867_SW_RESTART); 830 if (err < 0) 831 return err; 832 833 usleep_range(10, 20); 834 835 return phy_modify(phydev, MII_DP83867_PHYCTRL, 836 DP83867_PHYCR_FORCE_LINK_GOOD, 0); 837 } 838 839 static struct phy_driver dp83867_driver[] = { 840 { 841 .phy_id = DP83867_PHY_ID, 842 .phy_id_mask = 0xfffffff0, 843 .name = "TI DP83867", 844 /* PHY_GBIT_FEATURES */ 845 846 .probe = dp83867_probe, 847 .config_init = dp83867_config_init, 848 .soft_reset = dp83867_phy_reset, 849 850 .read_status = dp83867_read_status, 851 .get_tunable = dp83867_get_tunable, 852 .set_tunable = dp83867_set_tunable, 853 854 .get_wol = dp83867_get_wol, 855 .set_wol = dp83867_set_wol, 856 857 /* IRQ related */ 858 .config_intr = dp83867_config_intr, 859 .handle_interrupt = dp83867_handle_interrupt, 860 861 .suspend = genphy_suspend, 862 .resume = genphy_resume, 863 }, 864 }; 865 module_phy_driver(dp83867_driver); 866 867 static struct mdio_device_id __maybe_unused dp83867_tbl[] = { 868 { DP83867_PHY_ID, 0xfffffff0 }, 869 { } 870 }; 871 872 MODULE_DEVICE_TABLE(mdio, dp83867_tbl); 873 874 MODULE_DESCRIPTION("Texas Instruments DP83867 PHY driver"); 875 MODULE_AUTHOR("Dan Murphy <dmurphy@ti.com"); 876 MODULE_LICENSE("GPL v2"); 877