1 // SPDX-License-Identifier: GPL-2.0 2 // 3 // Secure Digital Host Controller 4 // 5 // Copyright (C) 2018 Spreadtrum, Inc. 6 // Author: Chunyan Zhang <chunyan.zhang@unisoc.com> 7 8 #include <linux/delay.h> 9 #include <linux/dma-mapping.h> 10 #include <linux/highmem.h> 11 #include <linux/iopoll.h> 12 #include <linux/module.h> 13 #include <linux/of.h> 14 #include <linux/of_device.h> 15 #include <linux/of_gpio.h> 16 #include <linux/pinctrl/consumer.h> 17 #include <linux/platform_device.h> 18 #include <linux/pm_runtime.h> 19 #include <linux/regulator/consumer.h> 20 #include <linux/slab.h> 21 22 #include "sdhci-pltfm.h" 23 #include "mmc_hsq.h" 24 25 /* SDHCI_ARGUMENT2 register high 16bit */ 26 #define SDHCI_SPRD_ARG2_STUFF GENMASK(31, 16) 27 28 #define SDHCI_SPRD_REG_32_DLL_CFG 0x200 29 #define SDHCI_SPRD_DLL_ALL_CPST_EN (BIT(18) | BIT(24) | BIT(25) | BIT(26) | BIT(27)) 30 #define SDHCI_SPRD_DLL_EN BIT(21) 31 #define SDHCI_SPRD_DLL_SEARCH_MODE BIT(16) 32 #define SDHCI_SPRD_DLL_INIT_COUNT 0xc00 33 #define SDHCI_SPRD_DLL_PHASE_INTERNAL 0x3 34 35 #define SDHCI_SPRD_REG_32_DLL_DLY 0x204 36 37 #define SDHCI_SPRD_REG_32_DLL_DLY_OFFSET 0x208 38 #define SDHCIBSPRD_IT_WR_DLY_INV BIT(5) 39 #define SDHCI_SPRD_BIT_CMD_DLY_INV BIT(13) 40 #define SDHCI_SPRD_BIT_POSRD_DLY_INV BIT(21) 41 #define SDHCI_SPRD_BIT_NEGRD_DLY_INV BIT(29) 42 43 #define SDHCI_SPRD_REG_32_DLL_STS0 0x210 44 #define SDHCI_SPRD_DLL_LOCKED BIT(18) 45 46 #define SDHCI_SPRD_REG_32_BUSY_POSI 0x250 47 #define SDHCI_SPRD_BIT_OUTR_CLK_AUTO_EN BIT(25) 48 #define SDHCI_SPRD_BIT_INNR_CLK_AUTO_EN BIT(24) 49 50 #define SDHCI_SPRD_REG_DEBOUNCE 0x28C 51 #define SDHCI_SPRD_BIT_DLL_BAK BIT(0) 52 #define SDHCI_SPRD_BIT_DLL_VAL BIT(1) 53 54 #define SDHCI_SPRD_INT_SIGNAL_MASK 0x1B7F410B 55 56 /* SDHCI_HOST_CONTROL2 */ 57 #define SDHCI_SPRD_CTRL_HS200 0x0005 58 #define SDHCI_SPRD_CTRL_HS400 0x0006 59 #define SDHCI_SPRD_CTRL_HS400ES 0x0007 60 61 /* 62 * According to the standard specification, BIT(3) of SDHCI_SOFTWARE_RESET is 63 * reserved, and only used on Spreadtrum's design, the hardware cannot work 64 * if this bit is cleared. 65 * 1 : normal work 66 * 0 : hardware reset 67 */ 68 #define SDHCI_HW_RESET_CARD BIT(3) 69 70 #define SDHCI_SPRD_MAX_CUR 0xFFFFFF 71 #define SDHCI_SPRD_CLK_MAX_DIV 1023 72 73 #define SDHCI_SPRD_CLK_DEF_RATE 26000000 74 #define SDHCI_SPRD_PHY_DLL_CLK 52000000 75 76 struct sdhci_sprd_host { 77 u32 version; 78 struct clk *clk_sdio; 79 struct clk *clk_enable; 80 struct clk *clk_2x_enable; 81 struct pinctrl *pinctrl; 82 struct pinctrl_state *pins_uhs; 83 struct pinctrl_state *pins_default; 84 u32 base_rate; 85 int flags; /* backup of host attribute */ 86 u32 phy_delay[MMC_TIMING_MMC_HS400 + 2]; 87 }; 88 89 struct sdhci_sprd_phy_cfg { 90 const char *property; 91 u8 timing; 92 }; 93 94 static const struct sdhci_sprd_phy_cfg sdhci_sprd_phy_cfgs[] = { 95 { "sprd,phy-delay-legacy", MMC_TIMING_LEGACY, }, 96 { "sprd,phy-delay-sd-highspeed", MMC_TIMING_SD_HS, }, 97 { "sprd,phy-delay-sd-uhs-sdr50", MMC_TIMING_UHS_SDR50, }, 98 { "sprd,phy-delay-sd-uhs-sdr104", MMC_TIMING_UHS_SDR104, }, 99 { "sprd,phy-delay-mmc-highspeed", MMC_TIMING_MMC_HS, }, 100 { "sprd,phy-delay-mmc-ddr52", MMC_TIMING_MMC_DDR52, }, 101 { "sprd,phy-delay-mmc-hs200", MMC_TIMING_MMC_HS200, }, 102 { "sprd,phy-delay-mmc-hs400", MMC_TIMING_MMC_HS400, }, 103 { "sprd,phy-delay-mmc-hs400es", MMC_TIMING_MMC_HS400 + 1, }, 104 }; 105 106 #define TO_SPRD_HOST(host) sdhci_pltfm_priv(sdhci_priv(host)) 107 108 static void sdhci_sprd_init_config(struct sdhci_host *host) 109 { 110 u16 val; 111 112 /* set dll backup mode */ 113 val = sdhci_readl(host, SDHCI_SPRD_REG_DEBOUNCE); 114 val |= SDHCI_SPRD_BIT_DLL_BAK | SDHCI_SPRD_BIT_DLL_VAL; 115 sdhci_writel(host, val, SDHCI_SPRD_REG_DEBOUNCE); 116 } 117 118 static inline u32 sdhci_sprd_readl(struct sdhci_host *host, int reg) 119 { 120 if (unlikely(reg == SDHCI_MAX_CURRENT)) 121 return SDHCI_SPRD_MAX_CUR; 122 123 return readl_relaxed(host->ioaddr + reg); 124 } 125 126 static inline void sdhci_sprd_writel(struct sdhci_host *host, u32 val, int reg) 127 { 128 /* SDHCI_MAX_CURRENT is reserved on Spreadtrum's platform */ 129 if (unlikely(reg == SDHCI_MAX_CURRENT)) 130 return; 131 132 if (unlikely(reg == SDHCI_SIGNAL_ENABLE || reg == SDHCI_INT_ENABLE)) 133 val = val & SDHCI_SPRD_INT_SIGNAL_MASK; 134 135 writel_relaxed(val, host->ioaddr + reg); 136 } 137 138 static inline void sdhci_sprd_writew(struct sdhci_host *host, u16 val, int reg) 139 { 140 /* SDHCI_BLOCK_COUNT is Read Only on Spreadtrum's platform */ 141 if (unlikely(reg == SDHCI_BLOCK_COUNT)) 142 return; 143 144 writew_relaxed(val, host->ioaddr + reg); 145 } 146 147 static inline void sdhci_sprd_writeb(struct sdhci_host *host, u8 val, int reg) 148 { 149 /* 150 * Since BIT(3) of SDHCI_SOFTWARE_RESET is reserved according to the 151 * standard specification, sdhci_reset() write this register directly 152 * without checking other reserved bits, that will clear BIT(3) which 153 * is defined as hardware reset on Spreadtrum's platform and clearing 154 * it by mistake will lead the card not work. So here we need to work 155 * around it. 156 */ 157 if (unlikely(reg == SDHCI_SOFTWARE_RESET)) { 158 if (readb_relaxed(host->ioaddr + reg) & SDHCI_HW_RESET_CARD) 159 val |= SDHCI_HW_RESET_CARD; 160 } 161 162 writeb_relaxed(val, host->ioaddr + reg); 163 } 164 165 static inline void sdhci_sprd_sd_clk_off(struct sdhci_host *host) 166 { 167 u16 ctrl = sdhci_readw(host, SDHCI_CLOCK_CONTROL); 168 169 ctrl &= ~SDHCI_CLOCK_CARD_EN; 170 sdhci_writew(host, ctrl, SDHCI_CLOCK_CONTROL); 171 } 172 173 static inline void sdhci_sprd_sd_clk_on(struct sdhci_host *host) 174 { 175 u16 ctrl; 176 177 ctrl = sdhci_readw(host, SDHCI_CLOCK_CONTROL); 178 ctrl |= SDHCI_CLOCK_CARD_EN; 179 sdhci_writew(host, ctrl, SDHCI_CLOCK_CONTROL); 180 } 181 182 static inline void 183 sdhci_sprd_set_dll_invert(struct sdhci_host *host, u32 mask, bool en) 184 { 185 u32 dll_dly_offset; 186 187 dll_dly_offset = sdhci_readl(host, SDHCI_SPRD_REG_32_DLL_DLY_OFFSET); 188 if (en) 189 dll_dly_offset |= mask; 190 else 191 dll_dly_offset &= ~mask; 192 sdhci_writel(host, dll_dly_offset, SDHCI_SPRD_REG_32_DLL_DLY_OFFSET); 193 } 194 195 static inline u32 sdhci_sprd_calc_div(u32 base_clk, u32 clk) 196 { 197 u32 div; 198 199 /* select 2x clock source */ 200 if (base_clk <= clk * 2) 201 return 0; 202 203 div = (u32) (base_clk / (clk * 2)); 204 205 if ((base_clk / div) > (clk * 2)) 206 div++; 207 208 if (div % 2) 209 div = (div + 1) / 2; 210 else 211 div = div / 2; 212 213 if (div > SDHCI_SPRD_CLK_MAX_DIV) 214 div = SDHCI_SPRD_CLK_MAX_DIV; 215 216 return div; 217 } 218 219 static inline void _sdhci_sprd_set_clock(struct sdhci_host *host, 220 unsigned int clk) 221 { 222 struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host); 223 u32 div, val, mask; 224 225 sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL); 226 227 div = sdhci_sprd_calc_div(sprd_host->base_rate, clk); 228 div = ((div & 0x300) >> 2) | ((div & 0xFF) << 8); 229 sdhci_enable_clk(host, div); 230 231 /* enable auto gate sdhc_enable_auto_gate */ 232 val = sdhci_readl(host, SDHCI_SPRD_REG_32_BUSY_POSI); 233 mask = SDHCI_SPRD_BIT_OUTR_CLK_AUTO_EN | 234 SDHCI_SPRD_BIT_INNR_CLK_AUTO_EN; 235 if (mask != (val & mask)) { 236 val |= mask; 237 sdhci_writel(host, val, SDHCI_SPRD_REG_32_BUSY_POSI); 238 } 239 } 240 241 static void sdhci_sprd_enable_phy_dll(struct sdhci_host *host) 242 { 243 u32 tmp; 244 245 tmp = sdhci_readl(host, SDHCI_SPRD_REG_32_DLL_CFG); 246 tmp &= ~(SDHCI_SPRD_DLL_EN | SDHCI_SPRD_DLL_ALL_CPST_EN); 247 sdhci_writel(host, tmp, SDHCI_SPRD_REG_32_DLL_CFG); 248 /* wait 1ms */ 249 usleep_range(1000, 1250); 250 251 tmp = sdhci_readl(host, SDHCI_SPRD_REG_32_DLL_CFG); 252 tmp |= SDHCI_SPRD_DLL_ALL_CPST_EN | SDHCI_SPRD_DLL_SEARCH_MODE | 253 SDHCI_SPRD_DLL_INIT_COUNT | SDHCI_SPRD_DLL_PHASE_INTERNAL; 254 sdhci_writel(host, tmp, SDHCI_SPRD_REG_32_DLL_CFG); 255 /* wait 1ms */ 256 usleep_range(1000, 1250); 257 258 tmp = sdhci_readl(host, SDHCI_SPRD_REG_32_DLL_CFG); 259 tmp |= SDHCI_SPRD_DLL_EN; 260 sdhci_writel(host, tmp, SDHCI_SPRD_REG_32_DLL_CFG); 261 /* wait 1ms */ 262 usleep_range(1000, 1250); 263 264 if (read_poll_timeout(sdhci_readl, tmp, (tmp & SDHCI_SPRD_DLL_LOCKED), 265 2000, USEC_PER_SEC, false, host, SDHCI_SPRD_REG_32_DLL_STS0)) { 266 pr_err("%s: DLL locked fail!\n", mmc_hostname(host->mmc)); 267 pr_info("%s: DLL_STS0 : 0x%x, DLL_CFG : 0x%x\n", 268 mmc_hostname(host->mmc), 269 sdhci_readl(host, SDHCI_SPRD_REG_32_DLL_STS0), 270 sdhci_readl(host, SDHCI_SPRD_REG_32_DLL_CFG)); 271 } 272 } 273 274 static void sdhci_sprd_set_clock(struct sdhci_host *host, unsigned int clock) 275 { 276 bool en = false, clk_changed = false; 277 278 if (clock == 0) { 279 sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL); 280 } else if (clock != host->clock) { 281 sdhci_sprd_sd_clk_off(host); 282 _sdhci_sprd_set_clock(host, clock); 283 284 if (clock <= 400000) 285 en = true; 286 sdhci_sprd_set_dll_invert(host, SDHCI_SPRD_BIT_CMD_DLY_INV | 287 SDHCI_SPRD_BIT_POSRD_DLY_INV, en); 288 clk_changed = true; 289 } else { 290 _sdhci_sprd_set_clock(host, clock); 291 } 292 293 /* 294 * According to the Spreadtrum SD host specification, when we changed 295 * the clock to be more than 52M, we should enable the PHY DLL which 296 * is used to track the clock frequency to make the clock work more 297 * stable. Otherwise deviation may occur of the higher clock. 298 */ 299 if (clk_changed && clock > SDHCI_SPRD_PHY_DLL_CLK) 300 sdhci_sprd_enable_phy_dll(host); 301 } 302 303 static unsigned int sdhci_sprd_get_max_clock(struct sdhci_host *host) 304 { 305 struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host); 306 307 return clk_round_rate(sprd_host->clk_sdio, ULONG_MAX); 308 } 309 310 static unsigned int sdhci_sprd_get_min_clock(struct sdhci_host *host) 311 { 312 return 100000; 313 } 314 315 static void sdhci_sprd_set_uhs_signaling(struct sdhci_host *host, 316 unsigned int timing) 317 { 318 struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host); 319 struct mmc_host *mmc = host->mmc; 320 u32 *p = sprd_host->phy_delay; 321 u16 ctrl_2; 322 323 if (timing == host->timing) 324 return; 325 326 ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2); 327 /* Select Bus Speed Mode for host */ 328 ctrl_2 &= ~SDHCI_CTRL_UHS_MASK; 329 switch (timing) { 330 case MMC_TIMING_UHS_SDR12: 331 ctrl_2 |= SDHCI_CTRL_UHS_SDR12; 332 break; 333 case MMC_TIMING_MMC_HS: 334 case MMC_TIMING_SD_HS: 335 case MMC_TIMING_UHS_SDR25: 336 ctrl_2 |= SDHCI_CTRL_UHS_SDR25; 337 break; 338 case MMC_TIMING_UHS_SDR50: 339 ctrl_2 |= SDHCI_CTRL_UHS_SDR50; 340 break; 341 case MMC_TIMING_UHS_SDR104: 342 ctrl_2 |= SDHCI_CTRL_UHS_SDR104; 343 break; 344 case MMC_TIMING_UHS_DDR50: 345 case MMC_TIMING_MMC_DDR52: 346 ctrl_2 |= SDHCI_CTRL_UHS_DDR50; 347 break; 348 case MMC_TIMING_MMC_HS200: 349 ctrl_2 |= SDHCI_SPRD_CTRL_HS200; 350 break; 351 case MMC_TIMING_MMC_HS400: 352 ctrl_2 |= SDHCI_SPRD_CTRL_HS400; 353 break; 354 default: 355 break; 356 } 357 358 sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2); 359 360 if (!mmc->ios.enhanced_strobe) 361 sdhci_writel(host, p[timing], SDHCI_SPRD_REG_32_DLL_DLY); 362 } 363 364 static void sdhci_sprd_hw_reset(struct sdhci_host *host) 365 { 366 int val; 367 368 /* 369 * Note: don't use sdhci_writeb() API here since it is redirected to 370 * sdhci_sprd_writeb() in which we have a workaround for 371 * SDHCI_SOFTWARE_RESET which would make bit SDHCI_HW_RESET_CARD can 372 * not be cleared. 373 */ 374 val = readb_relaxed(host->ioaddr + SDHCI_SOFTWARE_RESET); 375 val &= ~SDHCI_HW_RESET_CARD; 376 writeb_relaxed(val, host->ioaddr + SDHCI_SOFTWARE_RESET); 377 /* wait for 10 us */ 378 usleep_range(10, 20); 379 380 val |= SDHCI_HW_RESET_CARD; 381 writeb_relaxed(val, host->ioaddr + SDHCI_SOFTWARE_RESET); 382 usleep_range(300, 500); 383 } 384 385 static unsigned int sdhci_sprd_get_max_timeout_count(struct sdhci_host *host) 386 { 387 /* The Spredtrum controller actual maximum timeout count is 1 << 31 */ 388 return 1 << 31; 389 } 390 391 static unsigned int sdhci_sprd_get_ro(struct sdhci_host *host) 392 { 393 return 0; 394 } 395 396 static void sdhci_sprd_request_done(struct sdhci_host *host, 397 struct mmc_request *mrq) 398 { 399 /* Validate if the request was from software queue firstly. */ 400 if (mmc_hsq_finalize_request(host->mmc, mrq)) 401 return; 402 403 mmc_request_done(host->mmc, mrq); 404 } 405 406 static struct sdhci_ops sdhci_sprd_ops = { 407 .read_l = sdhci_sprd_readl, 408 .write_l = sdhci_sprd_writel, 409 .write_w = sdhci_sprd_writew, 410 .write_b = sdhci_sprd_writeb, 411 .set_clock = sdhci_sprd_set_clock, 412 .get_max_clock = sdhci_sprd_get_max_clock, 413 .get_min_clock = sdhci_sprd_get_min_clock, 414 .set_bus_width = sdhci_set_bus_width, 415 .reset = sdhci_reset, 416 .set_uhs_signaling = sdhci_sprd_set_uhs_signaling, 417 .hw_reset = sdhci_sprd_hw_reset, 418 .get_max_timeout_count = sdhci_sprd_get_max_timeout_count, 419 .get_ro = sdhci_sprd_get_ro, 420 .request_done = sdhci_sprd_request_done, 421 }; 422 423 static void sdhci_sprd_check_auto_cmd23(struct mmc_host *mmc, 424 struct mmc_request *mrq) 425 { 426 struct sdhci_host *host = mmc_priv(mmc); 427 struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host); 428 429 host->flags |= sprd_host->flags & SDHCI_AUTO_CMD23; 430 431 /* 432 * From version 4.10 onward, ARGUMENT2 register is also as 32-bit 433 * block count register which doesn't support stuff bits of 434 * CMD23 argument on Spreadtrum's sd host controller. 435 */ 436 if (host->version >= SDHCI_SPEC_410 && 437 mrq->sbc && (mrq->sbc->arg & SDHCI_SPRD_ARG2_STUFF) && 438 (host->flags & SDHCI_AUTO_CMD23)) 439 host->flags &= ~SDHCI_AUTO_CMD23; 440 } 441 442 static void sdhci_sprd_request(struct mmc_host *mmc, struct mmc_request *mrq) 443 { 444 sdhci_sprd_check_auto_cmd23(mmc, mrq); 445 446 sdhci_request(mmc, mrq); 447 } 448 449 static int sdhci_sprd_request_atomic(struct mmc_host *mmc, 450 struct mmc_request *mrq) 451 { 452 sdhci_sprd_check_auto_cmd23(mmc, mrq); 453 454 return sdhci_request_atomic(mmc, mrq); 455 } 456 457 static int sdhci_sprd_voltage_switch(struct mmc_host *mmc, struct mmc_ios *ios) 458 { 459 struct sdhci_host *host = mmc_priv(mmc); 460 struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host); 461 int ret; 462 463 if (!IS_ERR(mmc->supply.vqmmc)) { 464 ret = mmc_regulator_set_vqmmc(mmc, ios); 465 if (ret < 0) { 466 pr_err("%s: Switching signalling voltage failed\n", 467 mmc_hostname(mmc)); 468 return ret; 469 } 470 } 471 472 if (IS_ERR(sprd_host->pinctrl)) 473 return 0; 474 475 switch (ios->signal_voltage) { 476 case MMC_SIGNAL_VOLTAGE_180: 477 ret = pinctrl_select_state(sprd_host->pinctrl, 478 sprd_host->pins_uhs); 479 if (ret) { 480 pr_err("%s: failed to select uhs pin state\n", 481 mmc_hostname(mmc)); 482 return ret; 483 } 484 break; 485 486 default: 487 fallthrough; 488 case MMC_SIGNAL_VOLTAGE_330: 489 ret = pinctrl_select_state(sprd_host->pinctrl, 490 sprd_host->pins_default); 491 if (ret) { 492 pr_err("%s: failed to select default pin state\n", 493 mmc_hostname(mmc)); 494 return ret; 495 } 496 break; 497 } 498 499 /* Wait for 300 ~ 500 us for pin state stable */ 500 usleep_range(300, 500); 501 sdhci_reset(host, SDHCI_RESET_CMD | SDHCI_RESET_DATA); 502 503 return 0; 504 } 505 506 static void sdhci_sprd_hs400_enhanced_strobe(struct mmc_host *mmc, 507 struct mmc_ios *ios) 508 { 509 struct sdhci_host *host = mmc_priv(mmc); 510 struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host); 511 u32 *p = sprd_host->phy_delay; 512 u16 ctrl_2; 513 514 if (!ios->enhanced_strobe) 515 return; 516 517 sdhci_sprd_sd_clk_off(host); 518 519 /* Set HS400 enhanced strobe mode */ 520 ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2); 521 ctrl_2 &= ~SDHCI_CTRL_UHS_MASK; 522 ctrl_2 |= SDHCI_SPRD_CTRL_HS400ES; 523 sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2); 524 525 sdhci_sprd_sd_clk_on(host); 526 527 /* Set the PHY DLL delay value for HS400 enhanced strobe mode */ 528 sdhci_writel(host, p[MMC_TIMING_MMC_HS400 + 1], 529 SDHCI_SPRD_REG_32_DLL_DLY); 530 } 531 532 static void sdhci_sprd_phy_param_parse(struct sdhci_sprd_host *sprd_host, 533 struct device_node *np) 534 { 535 u32 *p = sprd_host->phy_delay; 536 int ret, i, index; 537 u32 val[4]; 538 539 for (i = 0; i < ARRAY_SIZE(sdhci_sprd_phy_cfgs); i++) { 540 ret = of_property_read_u32_array(np, 541 sdhci_sprd_phy_cfgs[i].property, val, 4); 542 if (ret) 543 continue; 544 545 index = sdhci_sprd_phy_cfgs[i].timing; 546 p[index] = val[0] | (val[1] << 8) | (val[2] << 16) | (val[3] << 24); 547 } 548 } 549 550 static const struct sdhci_pltfm_data sdhci_sprd_pdata = { 551 .quirks = SDHCI_QUIRK_BROKEN_CARD_DETECTION | 552 SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK | 553 SDHCI_QUIRK_MISSING_CAPS, 554 .quirks2 = SDHCI_QUIRK2_BROKEN_HS200 | 555 SDHCI_QUIRK2_USE_32BIT_BLK_CNT | 556 SDHCI_QUIRK2_PRESET_VALUE_BROKEN, 557 .ops = &sdhci_sprd_ops, 558 }; 559 560 static int sdhci_sprd_probe(struct platform_device *pdev) 561 { 562 struct sdhci_host *host; 563 struct sdhci_sprd_host *sprd_host; 564 struct mmc_hsq *hsq; 565 struct clk *clk; 566 int ret = 0; 567 568 host = sdhci_pltfm_init(pdev, &sdhci_sprd_pdata, sizeof(*sprd_host)); 569 if (IS_ERR(host)) 570 return PTR_ERR(host); 571 572 host->dma_mask = DMA_BIT_MASK(64); 573 pdev->dev.dma_mask = &host->dma_mask; 574 host->mmc_host_ops.request = sdhci_sprd_request; 575 host->mmc_host_ops.hs400_enhanced_strobe = 576 sdhci_sprd_hs400_enhanced_strobe; 577 /* 578 * We can not use the standard ops to change and detect the voltage 579 * signal for Spreadtrum SD host controller, since our voltage regulator 580 * for I/O is fixed in hardware, that means we do not need control 581 * the standard SD host controller to change the I/O voltage. 582 */ 583 host->mmc_host_ops.start_signal_voltage_switch = 584 sdhci_sprd_voltage_switch; 585 586 host->mmc->caps = MMC_CAP_SD_HIGHSPEED | MMC_CAP_MMC_HIGHSPEED | 587 MMC_CAP_WAIT_WHILE_BUSY; 588 589 ret = mmc_of_parse(host->mmc); 590 if (ret) 591 goto pltfm_free; 592 593 if (!mmc_card_is_removable(host->mmc)) 594 host->mmc_host_ops.request_atomic = sdhci_sprd_request_atomic; 595 else 596 host->always_defer_done = true; 597 598 sprd_host = TO_SPRD_HOST(host); 599 sdhci_sprd_phy_param_parse(sprd_host, pdev->dev.of_node); 600 601 sprd_host->pinctrl = devm_pinctrl_get(&pdev->dev); 602 if (!IS_ERR(sprd_host->pinctrl)) { 603 sprd_host->pins_uhs = 604 pinctrl_lookup_state(sprd_host->pinctrl, "state_uhs"); 605 if (IS_ERR(sprd_host->pins_uhs)) { 606 ret = PTR_ERR(sprd_host->pins_uhs); 607 goto pltfm_free; 608 } 609 610 sprd_host->pins_default = 611 pinctrl_lookup_state(sprd_host->pinctrl, "default"); 612 if (IS_ERR(sprd_host->pins_default)) { 613 ret = PTR_ERR(sprd_host->pins_default); 614 goto pltfm_free; 615 } 616 } 617 618 clk = devm_clk_get(&pdev->dev, "sdio"); 619 if (IS_ERR(clk)) { 620 ret = PTR_ERR(clk); 621 goto pltfm_free; 622 } 623 sprd_host->clk_sdio = clk; 624 sprd_host->base_rate = clk_get_rate(sprd_host->clk_sdio); 625 if (!sprd_host->base_rate) 626 sprd_host->base_rate = SDHCI_SPRD_CLK_DEF_RATE; 627 628 clk = devm_clk_get(&pdev->dev, "enable"); 629 if (IS_ERR(clk)) { 630 ret = PTR_ERR(clk); 631 goto pltfm_free; 632 } 633 sprd_host->clk_enable = clk; 634 635 clk = devm_clk_get(&pdev->dev, "2x_enable"); 636 if (!IS_ERR(clk)) 637 sprd_host->clk_2x_enable = clk; 638 639 ret = clk_prepare_enable(sprd_host->clk_sdio); 640 if (ret) 641 goto pltfm_free; 642 643 ret = clk_prepare_enable(sprd_host->clk_enable); 644 if (ret) 645 goto clk_disable; 646 647 ret = clk_prepare_enable(sprd_host->clk_2x_enable); 648 if (ret) 649 goto clk_disable2; 650 651 sdhci_sprd_init_config(host); 652 host->version = sdhci_readw(host, SDHCI_HOST_VERSION); 653 sprd_host->version = ((host->version & SDHCI_VENDOR_VER_MASK) >> 654 SDHCI_VENDOR_VER_SHIFT); 655 656 pm_runtime_get_noresume(&pdev->dev); 657 pm_runtime_set_active(&pdev->dev); 658 pm_runtime_enable(&pdev->dev); 659 pm_runtime_set_autosuspend_delay(&pdev->dev, 50); 660 pm_runtime_use_autosuspend(&pdev->dev); 661 pm_suspend_ignore_children(&pdev->dev, 1); 662 663 sdhci_enable_v4_mode(host); 664 665 /* 666 * Supply the existing CAPS, but clear the UHS-I modes. This 667 * will allow these modes to be specified only by device 668 * tree properties through mmc_of_parse(). 669 */ 670 host->caps = sdhci_readl(host, SDHCI_CAPABILITIES); 671 host->caps1 = sdhci_readl(host, SDHCI_CAPABILITIES_1); 672 host->caps1 &= ~(SDHCI_SUPPORT_SDR50 | SDHCI_SUPPORT_SDR104 | 673 SDHCI_SUPPORT_DDR50); 674 675 ret = sdhci_setup_host(host); 676 if (ret) 677 goto pm_runtime_disable; 678 679 sprd_host->flags = host->flags; 680 681 hsq = devm_kzalloc(&pdev->dev, sizeof(*hsq), GFP_KERNEL); 682 if (!hsq) { 683 ret = -ENOMEM; 684 goto err_cleanup_host; 685 } 686 687 ret = mmc_hsq_init(hsq, host->mmc); 688 if (ret) 689 goto err_cleanup_host; 690 691 ret = __sdhci_add_host(host); 692 if (ret) 693 goto err_cleanup_host; 694 695 pm_runtime_mark_last_busy(&pdev->dev); 696 pm_runtime_put_autosuspend(&pdev->dev); 697 698 return 0; 699 700 err_cleanup_host: 701 sdhci_cleanup_host(host); 702 703 pm_runtime_disable: 704 pm_runtime_put_noidle(&pdev->dev); 705 pm_runtime_disable(&pdev->dev); 706 pm_runtime_set_suspended(&pdev->dev); 707 708 clk_disable_unprepare(sprd_host->clk_2x_enable); 709 710 clk_disable2: 711 clk_disable_unprepare(sprd_host->clk_enable); 712 713 clk_disable: 714 clk_disable_unprepare(sprd_host->clk_sdio); 715 716 pltfm_free: 717 sdhci_pltfm_free(pdev); 718 return ret; 719 } 720 721 static int sdhci_sprd_remove(struct platform_device *pdev) 722 { 723 struct sdhci_host *host = platform_get_drvdata(pdev); 724 struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host); 725 726 sdhci_remove_host(host, 0); 727 728 clk_disable_unprepare(sprd_host->clk_sdio); 729 clk_disable_unprepare(sprd_host->clk_enable); 730 clk_disable_unprepare(sprd_host->clk_2x_enable); 731 732 sdhci_pltfm_free(pdev); 733 734 return 0; 735 } 736 737 static const struct of_device_id sdhci_sprd_of_match[] = { 738 { .compatible = "sprd,sdhci-r11", }, 739 { } 740 }; 741 MODULE_DEVICE_TABLE(of, sdhci_sprd_of_match); 742 743 #ifdef CONFIG_PM 744 static int sdhci_sprd_runtime_suspend(struct device *dev) 745 { 746 struct sdhci_host *host = dev_get_drvdata(dev); 747 struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host); 748 749 mmc_hsq_suspend(host->mmc); 750 sdhci_runtime_suspend_host(host); 751 752 clk_disable_unprepare(sprd_host->clk_sdio); 753 clk_disable_unprepare(sprd_host->clk_enable); 754 clk_disable_unprepare(sprd_host->clk_2x_enable); 755 756 return 0; 757 } 758 759 static int sdhci_sprd_runtime_resume(struct device *dev) 760 { 761 struct sdhci_host *host = dev_get_drvdata(dev); 762 struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host); 763 int ret; 764 765 ret = clk_prepare_enable(sprd_host->clk_2x_enable); 766 if (ret) 767 return ret; 768 769 ret = clk_prepare_enable(sprd_host->clk_enable); 770 if (ret) 771 goto clk_2x_disable; 772 773 ret = clk_prepare_enable(sprd_host->clk_sdio); 774 if (ret) 775 goto clk_disable; 776 777 sdhci_runtime_resume_host(host, 1); 778 mmc_hsq_resume(host->mmc); 779 780 return 0; 781 782 clk_disable: 783 clk_disable_unprepare(sprd_host->clk_enable); 784 785 clk_2x_disable: 786 clk_disable_unprepare(sprd_host->clk_2x_enable); 787 788 return ret; 789 } 790 #endif 791 792 static const struct dev_pm_ops sdhci_sprd_pm_ops = { 793 SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend, 794 pm_runtime_force_resume) 795 SET_RUNTIME_PM_OPS(sdhci_sprd_runtime_suspend, 796 sdhci_sprd_runtime_resume, NULL) 797 }; 798 799 static struct platform_driver sdhci_sprd_driver = { 800 .probe = sdhci_sprd_probe, 801 .remove = sdhci_sprd_remove, 802 .driver = { 803 .name = "sdhci_sprd_r11", 804 .probe_type = PROBE_PREFER_ASYNCHRONOUS, 805 .of_match_table = sdhci_sprd_of_match, 806 .pm = &sdhci_sprd_pm_ops, 807 }, 808 }; 809 module_platform_driver(sdhci_sprd_driver); 810 811 MODULE_DESCRIPTION("Spreadtrum sdio host controller r11 driver"); 812 MODULE_LICENSE("GPL v2"); 813 MODULE_ALIAS("platform:sdhci-sprd-r11"); 814