1 // SPDX-License-Identifier: GPL-2.0 2 // 3 // Secure Digital Host Controller 4 // 5 // Copyright (C) 2018 Spreadtrum, Inc. 6 // Author: Chunyan Zhang <chunyan.zhang@unisoc.com> 7 8 #include <linux/delay.h> 9 #include <linux/dma-mapping.h> 10 #include <linux/highmem.h> 11 #include <linux/module.h> 12 #include <linux/of.h> 13 #include <linux/of_device.h> 14 #include <linux/of_gpio.h> 15 #include <linux/pinctrl/consumer.h> 16 #include <linux/platform_device.h> 17 #include <linux/pm_runtime.h> 18 #include <linux/regulator/consumer.h> 19 #include <linux/slab.h> 20 21 #include "sdhci-pltfm.h" 22 #include "mmc_hsq.h" 23 24 /* SDHCI_ARGUMENT2 register high 16bit */ 25 #define SDHCI_SPRD_ARG2_STUFF GENMASK(31, 16) 26 27 #define SDHCI_SPRD_REG_32_DLL_CFG 0x200 28 #define SDHCI_SPRD_DLL_ALL_CPST_EN (BIT(18) | BIT(24) | BIT(25) | BIT(26) | BIT(27)) 29 #define SDHCI_SPRD_DLL_EN BIT(21) 30 #define SDHCI_SPRD_DLL_SEARCH_MODE BIT(16) 31 #define SDHCI_SPRD_DLL_INIT_COUNT 0xc00 32 #define SDHCI_SPRD_DLL_PHASE_INTERNAL 0x3 33 34 #define SDHCI_SPRD_REG_32_DLL_DLY 0x204 35 36 #define SDHCI_SPRD_REG_32_DLL_DLY_OFFSET 0x208 37 #define SDHCIBSPRD_IT_WR_DLY_INV BIT(5) 38 #define SDHCI_SPRD_BIT_CMD_DLY_INV BIT(13) 39 #define SDHCI_SPRD_BIT_POSRD_DLY_INV BIT(21) 40 #define SDHCI_SPRD_BIT_NEGRD_DLY_INV BIT(29) 41 42 #define SDHCI_SPRD_REG_32_BUSY_POSI 0x250 43 #define SDHCI_SPRD_BIT_OUTR_CLK_AUTO_EN BIT(25) 44 #define SDHCI_SPRD_BIT_INNR_CLK_AUTO_EN BIT(24) 45 46 #define SDHCI_SPRD_REG_DEBOUNCE 0x28C 47 #define SDHCI_SPRD_BIT_DLL_BAK BIT(0) 48 #define SDHCI_SPRD_BIT_DLL_VAL BIT(1) 49 50 #define SDHCI_SPRD_INT_SIGNAL_MASK 0x1B7F410B 51 52 /* SDHCI_HOST_CONTROL2 */ 53 #define SDHCI_SPRD_CTRL_HS200 0x0005 54 #define SDHCI_SPRD_CTRL_HS400 0x0006 55 #define SDHCI_SPRD_CTRL_HS400ES 0x0007 56 57 /* 58 * According to the standard specification, BIT(3) of SDHCI_SOFTWARE_RESET is 59 * reserved, and only used on Spreadtrum's design, the hardware cannot work 60 * if this bit is cleared. 61 * 1 : normal work 62 * 0 : hardware reset 63 */ 64 #define SDHCI_HW_RESET_CARD BIT(3) 65 66 #define SDHCI_SPRD_MAX_CUR 0xFFFFFF 67 #define SDHCI_SPRD_CLK_MAX_DIV 1023 68 69 #define SDHCI_SPRD_CLK_DEF_RATE 26000000 70 #define SDHCI_SPRD_PHY_DLL_CLK 52000000 71 72 struct sdhci_sprd_host { 73 u32 version; 74 struct clk *clk_sdio; 75 struct clk *clk_enable; 76 struct clk *clk_2x_enable; 77 struct pinctrl *pinctrl; 78 struct pinctrl_state *pins_uhs; 79 struct pinctrl_state *pins_default; 80 u32 base_rate; 81 int flags; /* backup of host attribute */ 82 u32 phy_delay[MMC_TIMING_MMC_HS400 + 2]; 83 }; 84 85 struct sdhci_sprd_phy_cfg { 86 const char *property; 87 u8 timing; 88 }; 89 90 static const struct sdhci_sprd_phy_cfg sdhci_sprd_phy_cfgs[] = { 91 { "sprd,phy-delay-legacy", MMC_TIMING_LEGACY, }, 92 { "sprd,phy-delay-sd-highspeed", MMC_TIMING_SD_HS, }, 93 { "sprd,phy-delay-sd-uhs-sdr50", MMC_TIMING_UHS_SDR50, }, 94 { "sprd,phy-delay-sd-uhs-sdr104", MMC_TIMING_UHS_SDR104, }, 95 { "sprd,phy-delay-mmc-highspeed", MMC_TIMING_MMC_HS, }, 96 { "sprd,phy-delay-mmc-ddr52", MMC_TIMING_MMC_DDR52, }, 97 { "sprd,phy-delay-mmc-hs200", MMC_TIMING_MMC_HS200, }, 98 { "sprd,phy-delay-mmc-hs400", MMC_TIMING_MMC_HS400, }, 99 { "sprd,phy-delay-mmc-hs400es", MMC_TIMING_MMC_HS400 + 1, }, 100 }; 101 102 #define TO_SPRD_HOST(host) sdhci_pltfm_priv(sdhci_priv(host)) 103 104 static void sdhci_sprd_init_config(struct sdhci_host *host) 105 { 106 u16 val; 107 108 /* set dll backup mode */ 109 val = sdhci_readl(host, SDHCI_SPRD_REG_DEBOUNCE); 110 val |= SDHCI_SPRD_BIT_DLL_BAK | SDHCI_SPRD_BIT_DLL_VAL; 111 sdhci_writel(host, val, SDHCI_SPRD_REG_DEBOUNCE); 112 } 113 114 static inline u32 sdhci_sprd_readl(struct sdhci_host *host, int reg) 115 { 116 if (unlikely(reg == SDHCI_MAX_CURRENT)) 117 return SDHCI_SPRD_MAX_CUR; 118 119 return readl_relaxed(host->ioaddr + reg); 120 } 121 122 static inline void sdhci_sprd_writel(struct sdhci_host *host, u32 val, int reg) 123 { 124 /* SDHCI_MAX_CURRENT is reserved on Spreadtrum's platform */ 125 if (unlikely(reg == SDHCI_MAX_CURRENT)) 126 return; 127 128 if (unlikely(reg == SDHCI_SIGNAL_ENABLE || reg == SDHCI_INT_ENABLE)) 129 val = val & SDHCI_SPRD_INT_SIGNAL_MASK; 130 131 writel_relaxed(val, host->ioaddr + reg); 132 } 133 134 static inline void sdhci_sprd_writew(struct sdhci_host *host, u16 val, int reg) 135 { 136 /* SDHCI_BLOCK_COUNT is Read Only on Spreadtrum's platform */ 137 if (unlikely(reg == SDHCI_BLOCK_COUNT)) 138 return; 139 140 writew_relaxed(val, host->ioaddr + reg); 141 } 142 143 static inline void sdhci_sprd_writeb(struct sdhci_host *host, u8 val, int reg) 144 { 145 /* 146 * Since BIT(3) of SDHCI_SOFTWARE_RESET is reserved according to the 147 * standard specification, sdhci_reset() write this register directly 148 * without checking other reserved bits, that will clear BIT(3) which 149 * is defined as hardware reset on Spreadtrum's platform and clearing 150 * it by mistake will lead the card not work. So here we need to work 151 * around it. 152 */ 153 if (unlikely(reg == SDHCI_SOFTWARE_RESET)) { 154 if (readb_relaxed(host->ioaddr + reg) & SDHCI_HW_RESET_CARD) 155 val |= SDHCI_HW_RESET_CARD; 156 } 157 158 writeb_relaxed(val, host->ioaddr + reg); 159 } 160 161 static inline void sdhci_sprd_sd_clk_off(struct sdhci_host *host) 162 { 163 u16 ctrl = sdhci_readw(host, SDHCI_CLOCK_CONTROL); 164 165 ctrl &= ~SDHCI_CLOCK_CARD_EN; 166 sdhci_writew(host, ctrl, SDHCI_CLOCK_CONTROL); 167 } 168 169 static inline void sdhci_sprd_sd_clk_on(struct sdhci_host *host) 170 { 171 u16 ctrl; 172 173 ctrl = sdhci_readw(host, SDHCI_CLOCK_CONTROL); 174 ctrl |= SDHCI_CLOCK_CARD_EN; 175 sdhci_writew(host, ctrl, SDHCI_CLOCK_CONTROL); 176 } 177 178 static inline void 179 sdhci_sprd_set_dll_invert(struct sdhci_host *host, u32 mask, bool en) 180 { 181 u32 dll_dly_offset; 182 183 dll_dly_offset = sdhci_readl(host, SDHCI_SPRD_REG_32_DLL_DLY_OFFSET); 184 if (en) 185 dll_dly_offset |= mask; 186 else 187 dll_dly_offset &= ~mask; 188 sdhci_writel(host, dll_dly_offset, SDHCI_SPRD_REG_32_DLL_DLY_OFFSET); 189 } 190 191 static inline u32 sdhci_sprd_calc_div(u32 base_clk, u32 clk) 192 { 193 u32 div; 194 195 /* select 2x clock source */ 196 if (base_clk <= clk * 2) 197 return 0; 198 199 div = (u32) (base_clk / (clk * 2)); 200 201 if ((base_clk / div) > (clk * 2)) 202 div++; 203 204 if (div > SDHCI_SPRD_CLK_MAX_DIV) 205 div = SDHCI_SPRD_CLK_MAX_DIV; 206 207 if (div % 2) 208 div = (div + 1) / 2; 209 else 210 div = div / 2; 211 212 return div; 213 } 214 215 static inline void _sdhci_sprd_set_clock(struct sdhci_host *host, 216 unsigned int clk) 217 { 218 struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host); 219 u32 div, val, mask; 220 221 sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL); 222 223 div = sdhci_sprd_calc_div(sprd_host->base_rate, clk); 224 div = ((div & 0x300) >> 2) | ((div & 0xFF) << 8); 225 sdhci_enable_clk(host, div); 226 227 /* enable auto gate sdhc_enable_auto_gate */ 228 val = sdhci_readl(host, SDHCI_SPRD_REG_32_BUSY_POSI); 229 mask = SDHCI_SPRD_BIT_OUTR_CLK_AUTO_EN | 230 SDHCI_SPRD_BIT_INNR_CLK_AUTO_EN; 231 if (mask != (val & mask)) { 232 val |= mask; 233 sdhci_writel(host, val, SDHCI_SPRD_REG_32_BUSY_POSI); 234 } 235 } 236 237 static void sdhci_sprd_enable_phy_dll(struct sdhci_host *host) 238 { 239 u32 tmp; 240 241 tmp = sdhci_readl(host, SDHCI_SPRD_REG_32_DLL_CFG); 242 tmp &= ~(SDHCI_SPRD_DLL_EN | SDHCI_SPRD_DLL_ALL_CPST_EN); 243 sdhci_writel(host, tmp, SDHCI_SPRD_REG_32_DLL_CFG); 244 /* wait 1ms */ 245 usleep_range(1000, 1250); 246 247 tmp = sdhci_readl(host, SDHCI_SPRD_REG_32_DLL_CFG); 248 tmp |= SDHCI_SPRD_DLL_ALL_CPST_EN | SDHCI_SPRD_DLL_SEARCH_MODE | 249 SDHCI_SPRD_DLL_INIT_COUNT | SDHCI_SPRD_DLL_PHASE_INTERNAL; 250 sdhci_writel(host, tmp, SDHCI_SPRD_REG_32_DLL_CFG); 251 /* wait 1ms */ 252 usleep_range(1000, 1250); 253 254 tmp = sdhci_readl(host, SDHCI_SPRD_REG_32_DLL_CFG); 255 tmp |= SDHCI_SPRD_DLL_EN; 256 sdhci_writel(host, tmp, SDHCI_SPRD_REG_32_DLL_CFG); 257 /* wait 1ms */ 258 usleep_range(1000, 1250); 259 } 260 261 static void sdhci_sprd_set_clock(struct sdhci_host *host, unsigned int clock) 262 { 263 bool en = false, clk_changed = false; 264 265 if (clock == 0) { 266 sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL); 267 } else if (clock != host->clock) { 268 sdhci_sprd_sd_clk_off(host); 269 _sdhci_sprd_set_clock(host, clock); 270 271 if (clock <= 400000) 272 en = true; 273 sdhci_sprd_set_dll_invert(host, SDHCI_SPRD_BIT_CMD_DLY_INV | 274 SDHCI_SPRD_BIT_POSRD_DLY_INV, en); 275 clk_changed = true; 276 } else { 277 _sdhci_sprd_set_clock(host, clock); 278 } 279 280 /* 281 * According to the Spreadtrum SD host specification, when we changed 282 * the clock to be more than 52M, we should enable the PHY DLL which 283 * is used to track the clock frequency to make the clock work more 284 * stable. Otherwise deviation may occur of the higher clock. 285 */ 286 if (clk_changed && clock > SDHCI_SPRD_PHY_DLL_CLK) 287 sdhci_sprd_enable_phy_dll(host); 288 } 289 290 static unsigned int sdhci_sprd_get_max_clock(struct sdhci_host *host) 291 { 292 struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host); 293 294 return clk_round_rate(sprd_host->clk_sdio, ULONG_MAX); 295 } 296 297 static unsigned int sdhci_sprd_get_min_clock(struct sdhci_host *host) 298 { 299 return 400000; 300 } 301 302 static void sdhci_sprd_set_uhs_signaling(struct sdhci_host *host, 303 unsigned int timing) 304 { 305 struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host); 306 struct mmc_host *mmc = host->mmc; 307 u32 *p = sprd_host->phy_delay; 308 u16 ctrl_2; 309 310 if (timing == host->timing) 311 return; 312 313 ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2); 314 /* Select Bus Speed Mode for host */ 315 ctrl_2 &= ~SDHCI_CTRL_UHS_MASK; 316 switch (timing) { 317 case MMC_TIMING_UHS_SDR12: 318 ctrl_2 |= SDHCI_CTRL_UHS_SDR12; 319 break; 320 case MMC_TIMING_MMC_HS: 321 case MMC_TIMING_SD_HS: 322 case MMC_TIMING_UHS_SDR25: 323 ctrl_2 |= SDHCI_CTRL_UHS_SDR25; 324 break; 325 case MMC_TIMING_UHS_SDR50: 326 ctrl_2 |= SDHCI_CTRL_UHS_SDR50; 327 break; 328 case MMC_TIMING_UHS_SDR104: 329 ctrl_2 |= SDHCI_CTRL_UHS_SDR104; 330 break; 331 case MMC_TIMING_UHS_DDR50: 332 case MMC_TIMING_MMC_DDR52: 333 ctrl_2 |= SDHCI_CTRL_UHS_DDR50; 334 break; 335 case MMC_TIMING_MMC_HS200: 336 ctrl_2 |= SDHCI_SPRD_CTRL_HS200; 337 break; 338 case MMC_TIMING_MMC_HS400: 339 ctrl_2 |= SDHCI_SPRD_CTRL_HS400; 340 break; 341 default: 342 break; 343 } 344 345 sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2); 346 347 if (!mmc->ios.enhanced_strobe) 348 sdhci_writel(host, p[timing], SDHCI_SPRD_REG_32_DLL_DLY); 349 } 350 351 static void sdhci_sprd_hw_reset(struct sdhci_host *host) 352 { 353 int val; 354 355 /* 356 * Note: don't use sdhci_writeb() API here since it is redirected to 357 * sdhci_sprd_writeb() in which we have a workaround for 358 * SDHCI_SOFTWARE_RESET which would make bit SDHCI_HW_RESET_CARD can 359 * not be cleared. 360 */ 361 val = readb_relaxed(host->ioaddr + SDHCI_SOFTWARE_RESET); 362 val &= ~SDHCI_HW_RESET_CARD; 363 writeb_relaxed(val, host->ioaddr + SDHCI_SOFTWARE_RESET); 364 /* wait for 10 us */ 365 usleep_range(10, 20); 366 367 val |= SDHCI_HW_RESET_CARD; 368 writeb_relaxed(val, host->ioaddr + SDHCI_SOFTWARE_RESET); 369 usleep_range(300, 500); 370 } 371 372 static unsigned int sdhci_sprd_get_max_timeout_count(struct sdhci_host *host) 373 { 374 /* The Spredtrum controller actual maximum timeout count is 1 << 31 */ 375 return 1 << 31; 376 } 377 378 static unsigned int sdhci_sprd_get_ro(struct sdhci_host *host) 379 { 380 return 0; 381 } 382 383 static void sdhci_sprd_request_done(struct sdhci_host *host, 384 struct mmc_request *mrq) 385 { 386 /* Validate if the request was from software queue firstly. */ 387 if (mmc_hsq_finalize_request(host->mmc, mrq)) 388 return; 389 390 mmc_request_done(host->mmc, mrq); 391 } 392 393 static struct sdhci_ops sdhci_sprd_ops = { 394 .read_l = sdhci_sprd_readl, 395 .write_l = sdhci_sprd_writel, 396 .write_b = sdhci_sprd_writeb, 397 .set_clock = sdhci_sprd_set_clock, 398 .get_max_clock = sdhci_sprd_get_max_clock, 399 .get_min_clock = sdhci_sprd_get_min_clock, 400 .set_bus_width = sdhci_set_bus_width, 401 .reset = sdhci_reset, 402 .set_uhs_signaling = sdhci_sprd_set_uhs_signaling, 403 .hw_reset = sdhci_sprd_hw_reset, 404 .get_max_timeout_count = sdhci_sprd_get_max_timeout_count, 405 .get_ro = sdhci_sprd_get_ro, 406 .request_done = sdhci_sprd_request_done, 407 }; 408 409 static void sdhci_sprd_check_auto_cmd23(struct mmc_host *mmc, 410 struct mmc_request *mrq) 411 { 412 struct sdhci_host *host = mmc_priv(mmc); 413 struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host); 414 415 host->flags |= sprd_host->flags & SDHCI_AUTO_CMD23; 416 417 /* 418 * From version 4.10 onward, ARGUMENT2 register is also as 32-bit 419 * block count register which doesn't support stuff bits of 420 * CMD23 argument on Spreadtrum's sd host controller. 421 */ 422 if (host->version >= SDHCI_SPEC_410 && 423 mrq->sbc && (mrq->sbc->arg & SDHCI_SPRD_ARG2_STUFF) && 424 (host->flags & SDHCI_AUTO_CMD23)) 425 host->flags &= ~SDHCI_AUTO_CMD23; 426 } 427 428 static void sdhci_sprd_request(struct mmc_host *mmc, struct mmc_request *mrq) 429 { 430 sdhci_sprd_check_auto_cmd23(mmc, mrq); 431 432 sdhci_request(mmc, mrq); 433 } 434 435 static int sdhci_sprd_request_atomic(struct mmc_host *mmc, 436 struct mmc_request *mrq) 437 { 438 sdhci_sprd_check_auto_cmd23(mmc, mrq); 439 440 return sdhci_request_atomic(mmc, mrq); 441 } 442 443 static int sdhci_sprd_voltage_switch(struct mmc_host *mmc, struct mmc_ios *ios) 444 { 445 struct sdhci_host *host = mmc_priv(mmc); 446 struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host); 447 int ret; 448 449 if (!IS_ERR(mmc->supply.vqmmc)) { 450 ret = mmc_regulator_set_vqmmc(mmc, ios); 451 if (ret < 0) { 452 pr_err("%s: Switching signalling voltage failed\n", 453 mmc_hostname(mmc)); 454 return ret; 455 } 456 } 457 458 if (IS_ERR(sprd_host->pinctrl)) 459 return 0; 460 461 switch (ios->signal_voltage) { 462 case MMC_SIGNAL_VOLTAGE_180: 463 ret = pinctrl_select_state(sprd_host->pinctrl, 464 sprd_host->pins_uhs); 465 if (ret) { 466 pr_err("%s: failed to select uhs pin state\n", 467 mmc_hostname(mmc)); 468 return ret; 469 } 470 break; 471 472 default: 473 fallthrough; 474 case MMC_SIGNAL_VOLTAGE_330: 475 ret = pinctrl_select_state(sprd_host->pinctrl, 476 sprd_host->pins_default); 477 if (ret) { 478 pr_err("%s: failed to select default pin state\n", 479 mmc_hostname(mmc)); 480 return ret; 481 } 482 break; 483 } 484 485 /* Wait for 300 ~ 500 us for pin state stable */ 486 usleep_range(300, 500); 487 sdhci_reset(host, SDHCI_RESET_CMD | SDHCI_RESET_DATA); 488 489 return 0; 490 } 491 492 static void sdhci_sprd_hs400_enhanced_strobe(struct mmc_host *mmc, 493 struct mmc_ios *ios) 494 { 495 struct sdhci_host *host = mmc_priv(mmc); 496 struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host); 497 u32 *p = sprd_host->phy_delay; 498 u16 ctrl_2; 499 500 if (!ios->enhanced_strobe) 501 return; 502 503 sdhci_sprd_sd_clk_off(host); 504 505 /* Set HS400 enhanced strobe mode */ 506 ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2); 507 ctrl_2 &= ~SDHCI_CTRL_UHS_MASK; 508 ctrl_2 |= SDHCI_SPRD_CTRL_HS400ES; 509 sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2); 510 511 sdhci_sprd_sd_clk_on(host); 512 513 /* Set the PHY DLL delay value for HS400 enhanced strobe mode */ 514 sdhci_writel(host, p[MMC_TIMING_MMC_HS400 + 1], 515 SDHCI_SPRD_REG_32_DLL_DLY); 516 } 517 518 static void sdhci_sprd_phy_param_parse(struct sdhci_sprd_host *sprd_host, 519 struct device_node *np) 520 { 521 u32 *p = sprd_host->phy_delay; 522 int ret, i, index; 523 u32 val[4]; 524 525 for (i = 0; i < ARRAY_SIZE(sdhci_sprd_phy_cfgs); i++) { 526 ret = of_property_read_u32_array(np, 527 sdhci_sprd_phy_cfgs[i].property, val, 4); 528 if (ret) 529 continue; 530 531 index = sdhci_sprd_phy_cfgs[i].timing; 532 p[index] = val[0] | (val[1] << 8) | (val[2] << 16) | (val[3] << 24); 533 } 534 } 535 536 static const struct sdhci_pltfm_data sdhci_sprd_pdata = { 537 .quirks = SDHCI_QUIRK_BROKEN_CARD_DETECTION | 538 SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK | 539 SDHCI_QUIRK_MISSING_CAPS, 540 .quirks2 = SDHCI_QUIRK2_BROKEN_HS200 | 541 SDHCI_QUIRK2_USE_32BIT_BLK_CNT | 542 SDHCI_QUIRK2_PRESET_VALUE_BROKEN, 543 .ops = &sdhci_sprd_ops, 544 }; 545 546 static int sdhci_sprd_probe(struct platform_device *pdev) 547 { 548 struct sdhci_host *host; 549 struct sdhci_sprd_host *sprd_host; 550 struct mmc_hsq *hsq; 551 struct clk *clk; 552 int ret = 0; 553 554 host = sdhci_pltfm_init(pdev, &sdhci_sprd_pdata, sizeof(*sprd_host)); 555 if (IS_ERR(host)) 556 return PTR_ERR(host); 557 558 host->dma_mask = DMA_BIT_MASK(64); 559 pdev->dev.dma_mask = &host->dma_mask; 560 host->mmc_host_ops.request = sdhci_sprd_request; 561 host->mmc_host_ops.hs400_enhanced_strobe = 562 sdhci_sprd_hs400_enhanced_strobe; 563 /* 564 * We can not use the standard ops to change and detect the voltage 565 * signal for Spreadtrum SD host controller, since our voltage regulator 566 * for I/O is fixed in hardware, that means we do not need control 567 * the standard SD host controller to change the I/O voltage. 568 */ 569 host->mmc_host_ops.start_signal_voltage_switch = 570 sdhci_sprd_voltage_switch; 571 572 host->mmc->caps = MMC_CAP_SD_HIGHSPEED | MMC_CAP_MMC_HIGHSPEED | 573 MMC_CAP_WAIT_WHILE_BUSY; 574 575 ret = mmc_of_parse(host->mmc); 576 if (ret) 577 goto pltfm_free; 578 579 if (!mmc_card_is_removable(host->mmc)) 580 host->mmc_host_ops.request_atomic = sdhci_sprd_request_atomic; 581 else 582 host->always_defer_done = true; 583 584 sprd_host = TO_SPRD_HOST(host); 585 sdhci_sprd_phy_param_parse(sprd_host, pdev->dev.of_node); 586 587 sprd_host->pinctrl = devm_pinctrl_get(&pdev->dev); 588 if (!IS_ERR(sprd_host->pinctrl)) { 589 sprd_host->pins_uhs = 590 pinctrl_lookup_state(sprd_host->pinctrl, "state_uhs"); 591 if (IS_ERR(sprd_host->pins_uhs)) { 592 ret = PTR_ERR(sprd_host->pins_uhs); 593 goto pltfm_free; 594 } 595 596 sprd_host->pins_default = 597 pinctrl_lookup_state(sprd_host->pinctrl, "default"); 598 if (IS_ERR(sprd_host->pins_default)) { 599 ret = PTR_ERR(sprd_host->pins_default); 600 goto pltfm_free; 601 } 602 } 603 604 clk = devm_clk_get(&pdev->dev, "sdio"); 605 if (IS_ERR(clk)) { 606 ret = PTR_ERR(clk); 607 goto pltfm_free; 608 } 609 sprd_host->clk_sdio = clk; 610 sprd_host->base_rate = clk_get_rate(sprd_host->clk_sdio); 611 if (!sprd_host->base_rate) 612 sprd_host->base_rate = SDHCI_SPRD_CLK_DEF_RATE; 613 614 clk = devm_clk_get(&pdev->dev, "enable"); 615 if (IS_ERR(clk)) { 616 ret = PTR_ERR(clk); 617 goto pltfm_free; 618 } 619 sprd_host->clk_enable = clk; 620 621 clk = devm_clk_get(&pdev->dev, "2x_enable"); 622 if (!IS_ERR(clk)) 623 sprd_host->clk_2x_enable = clk; 624 625 ret = clk_prepare_enable(sprd_host->clk_sdio); 626 if (ret) 627 goto pltfm_free; 628 629 ret = clk_prepare_enable(sprd_host->clk_enable); 630 if (ret) 631 goto clk_disable; 632 633 ret = clk_prepare_enable(sprd_host->clk_2x_enable); 634 if (ret) 635 goto clk_disable2; 636 637 sdhci_sprd_init_config(host); 638 host->version = sdhci_readw(host, SDHCI_HOST_VERSION); 639 sprd_host->version = ((host->version & SDHCI_VENDOR_VER_MASK) >> 640 SDHCI_VENDOR_VER_SHIFT); 641 642 pm_runtime_get_noresume(&pdev->dev); 643 pm_runtime_set_active(&pdev->dev); 644 pm_runtime_enable(&pdev->dev); 645 pm_runtime_set_autosuspend_delay(&pdev->dev, 50); 646 pm_runtime_use_autosuspend(&pdev->dev); 647 pm_suspend_ignore_children(&pdev->dev, 1); 648 649 sdhci_enable_v4_mode(host); 650 651 /* 652 * Supply the existing CAPS, but clear the UHS-I modes. This 653 * will allow these modes to be specified only by device 654 * tree properties through mmc_of_parse(). 655 */ 656 host->caps = sdhci_readl(host, SDHCI_CAPABILITIES); 657 host->caps1 = sdhci_readl(host, SDHCI_CAPABILITIES_1); 658 host->caps1 &= ~(SDHCI_SUPPORT_SDR50 | SDHCI_SUPPORT_SDR104 | 659 SDHCI_SUPPORT_DDR50); 660 661 ret = sdhci_setup_host(host); 662 if (ret) 663 goto pm_runtime_disable; 664 665 sprd_host->flags = host->flags; 666 667 hsq = devm_kzalloc(&pdev->dev, sizeof(*hsq), GFP_KERNEL); 668 if (!hsq) { 669 ret = -ENOMEM; 670 goto err_cleanup_host; 671 } 672 673 ret = mmc_hsq_init(hsq, host->mmc); 674 if (ret) 675 goto err_cleanup_host; 676 677 ret = __sdhci_add_host(host); 678 if (ret) 679 goto err_cleanup_host; 680 681 pm_runtime_mark_last_busy(&pdev->dev); 682 pm_runtime_put_autosuspend(&pdev->dev); 683 684 return 0; 685 686 err_cleanup_host: 687 sdhci_cleanup_host(host); 688 689 pm_runtime_disable: 690 pm_runtime_put_noidle(&pdev->dev); 691 pm_runtime_disable(&pdev->dev); 692 pm_runtime_set_suspended(&pdev->dev); 693 694 clk_disable_unprepare(sprd_host->clk_2x_enable); 695 696 clk_disable2: 697 clk_disable_unprepare(sprd_host->clk_enable); 698 699 clk_disable: 700 clk_disable_unprepare(sprd_host->clk_sdio); 701 702 pltfm_free: 703 sdhci_pltfm_free(pdev); 704 return ret; 705 } 706 707 static int sdhci_sprd_remove(struct platform_device *pdev) 708 { 709 struct sdhci_host *host = platform_get_drvdata(pdev); 710 struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host); 711 712 sdhci_remove_host(host, 0); 713 714 clk_disable_unprepare(sprd_host->clk_sdio); 715 clk_disable_unprepare(sprd_host->clk_enable); 716 clk_disable_unprepare(sprd_host->clk_2x_enable); 717 718 sdhci_pltfm_free(pdev); 719 720 return 0; 721 } 722 723 static const struct of_device_id sdhci_sprd_of_match[] = { 724 { .compatible = "sprd,sdhci-r11", }, 725 { } 726 }; 727 MODULE_DEVICE_TABLE(of, sdhci_sprd_of_match); 728 729 #ifdef CONFIG_PM 730 static int sdhci_sprd_runtime_suspend(struct device *dev) 731 { 732 struct sdhci_host *host = dev_get_drvdata(dev); 733 struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host); 734 735 mmc_hsq_suspend(host->mmc); 736 sdhci_runtime_suspend_host(host); 737 738 clk_disable_unprepare(sprd_host->clk_sdio); 739 clk_disable_unprepare(sprd_host->clk_enable); 740 clk_disable_unprepare(sprd_host->clk_2x_enable); 741 742 return 0; 743 } 744 745 static int sdhci_sprd_runtime_resume(struct device *dev) 746 { 747 struct sdhci_host *host = dev_get_drvdata(dev); 748 struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host); 749 int ret; 750 751 ret = clk_prepare_enable(sprd_host->clk_2x_enable); 752 if (ret) 753 return ret; 754 755 ret = clk_prepare_enable(sprd_host->clk_enable); 756 if (ret) 757 goto clk_2x_disable; 758 759 ret = clk_prepare_enable(sprd_host->clk_sdio); 760 if (ret) 761 goto clk_disable; 762 763 sdhci_runtime_resume_host(host, 1); 764 mmc_hsq_resume(host->mmc); 765 766 return 0; 767 768 clk_disable: 769 clk_disable_unprepare(sprd_host->clk_enable); 770 771 clk_2x_disable: 772 clk_disable_unprepare(sprd_host->clk_2x_enable); 773 774 return ret; 775 } 776 #endif 777 778 static const struct dev_pm_ops sdhci_sprd_pm_ops = { 779 SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend, 780 pm_runtime_force_resume) 781 SET_RUNTIME_PM_OPS(sdhci_sprd_runtime_suspend, 782 sdhci_sprd_runtime_resume, NULL) 783 }; 784 785 static struct platform_driver sdhci_sprd_driver = { 786 .probe = sdhci_sprd_probe, 787 .remove = sdhci_sprd_remove, 788 .driver = { 789 .name = "sdhci_sprd_r11", 790 .probe_type = PROBE_PREFER_ASYNCHRONOUS, 791 .of_match_table = sdhci_sprd_of_match, 792 .pm = &sdhci_sprd_pm_ops, 793 }, 794 }; 795 module_platform_driver(sdhci_sprd_driver); 796 797 MODULE_DESCRIPTION("Spreadtrum sdio host controller r11 driver"); 798 MODULE_LICENSE("GPL v2"); 799 MODULE_ALIAS("platform:sdhci-sprd-r11"); 800