1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * TI AEMIF driver 4 * 5 * Copyright (C) 2010 - 2013 Texas Instruments Incorporated. http://www.ti.com/ 6 * 7 * Authors: 8 * Murali Karicheri <m-karicheri2@ti.com> 9 * Ivan Khoronzhuk <ivan.khoronzhuk@ti.com> 10 */ 11 12 #include <linux/clk.h> 13 #include <linux/err.h> 14 #include <linux/io.h> 15 #include <linux/kernel.h> 16 #include <linux/module.h> 17 #include <linux/of.h> 18 #include <linux/of_platform.h> 19 #include <linux/platform_device.h> 20 #include <linux/platform_data/ti-aemif.h> 21 22 #define TA_SHIFT 2 23 #define RHOLD_SHIFT 4 24 #define RSTROBE_SHIFT 7 25 #define RSETUP_SHIFT 13 26 #define WHOLD_SHIFT 17 27 #define WSTROBE_SHIFT 20 28 #define WSETUP_SHIFT 26 29 #define EW_SHIFT 30 30 #define SSTROBE_SHIFT 31 31 32 #define TA(x) ((x) << TA_SHIFT) 33 #define RHOLD(x) ((x) << RHOLD_SHIFT) 34 #define RSTROBE(x) ((x) << RSTROBE_SHIFT) 35 #define RSETUP(x) ((x) << RSETUP_SHIFT) 36 #define WHOLD(x) ((x) << WHOLD_SHIFT) 37 #define WSTROBE(x) ((x) << WSTROBE_SHIFT) 38 #define WSETUP(x) ((x) << WSETUP_SHIFT) 39 #define EW(x) ((x) << EW_SHIFT) 40 #define SSTROBE(x) ((x) << SSTROBE_SHIFT) 41 42 #define ASIZE_MAX 0x1 43 #define TA_MAX 0x3 44 #define RHOLD_MAX 0x7 45 #define RSTROBE_MAX 0x3f 46 #define RSETUP_MAX 0xf 47 #define WHOLD_MAX 0x7 48 #define WSTROBE_MAX 0x3f 49 #define WSETUP_MAX 0xf 50 #define EW_MAX 0x1 51 #define SSTROBE_MAX 0x1 52 #define NUM_CS 4 53 54 #define TA_VAL(x) (((x) & TA(TA_MAX)) >> TA_SHIFT) 55 #define RHOLD_VAL(x) (((x) & RHOLD(RHOLD_MAX)) >> RHOLD_SHIFT) 56 #define RSTROBE_VAL(x) (((x) & RSTROBE(RSTROBE_MAX)) >> RSTROBE_SHIFT) 57 #define RSETUP_VAL(x) (((x) & RSETUP(RSETUP_MAX)) >> RSETUP_SHIFT) 58 #define WHOLD_VAL(x) (((x) & WHOLD(WHOLD_MAX)) >> WHOLD_SHIFT) 59 #define WSTROBE_VAL(x) (((x) & WSTROBE(WSTROBE_MAX)) >> WSTROBE_SHIFT) 60 #define WSETUP_VAL(x) (((x) & WSETUP(WSETUP_MAX)) >> WSETUP_SHIFT) 61 #define EW_VAL(x) (((x) & EW(EW_MAX)) >> EW_SHIFT) 62 #define SSTROBE_VAL(x) (((x) & SSTROBE(SSTROBE_MAX)) >> SSTROBE_SHIFT) 63 64 #define NRCSR_OFFSET 0x00 65 #define AWCCR_OFFSET 0x04 66 #define A1CR_OFFSET 0x10 67 68 #define ACR_ASIZE_MASK 0x3 69 #define ACR_EW_MASK BIT(30) 70 #define ACR_SSTROBE_MASK BIT(31) 71 #define ASIZE_16BIT 1 72 73 #define CONFIG_MASK (TA(TA_MAX) | \ 74 RHOLD(RHOLD_MAX) | \ 75 RSTROBE(RSTROBE_MAX) | \ 76 RSETUP(RSETUP_MAX) | \ 77 WHOLD(WHOLD_MAX) | \ 78 WSTROBE(WSTROBE_MAX) | \ 79 WSETUP(WSETUP_MAX) | \ 80 EW(EW_MAX) | SSTROBE(SSTROBE_MAX) | \ 81 ASIZE_MAX) 82 83 /** 84 * struct aemif_cs_data: structure to hold cs parameters 85 * @cs: chip-select number 86 * @wstrobe: write strobe width, ns 87 * @rstrobe: read strobe width, ns 88 * @wsetup: write setup width, ns 89 * @whold: write hold width, ns 90 * @rsetup: read setup width, ns 91 * @rhold: read hold width, ns 92 * @ta: minimum turn around time, ns 93 * @enable_ss: enable/disable select strobe mode 94 * @enable_ew: enable/disable extended wait mode 95 * @asize: width of the asynchronous device's data bus 96 */ 97 struct aemif_cs_data { 98 u8 cs; 99 u16 wstrobe; 100 u16 rstrobe; 101 u8 wsetup; 102 u8 whold; 103 u8 rsetup; 104 u8 rhold; 105 u8 ta; 106 u8 enable_ss; 107 u8 enable_ew; 108 u8 asize; 109 }; 110 111 /** 112 * struct aemif_device: structure to hold device data 113 * @base: base address of AEMIF registers 114 * @clk: source clock 115 * @clk_rate: clock's rate in kHz 116 * @num_cs: number of assigned chip-selects 117 * @cs_offset: start number of cs nodes 118 * @cs_data: array of chip-select settings 119 */ 120 struct aemif_device { 121 void __iomem *base; 122 struct clk *clk; 123 unsigned long clk_rate; 124 u8 num_cs; 125 int cs_offset; 126 struct aemif_cs_data cs_data[NUM_CS]; 127 }; 128 129 /** 130 * aemif_calc_rate - calculate timing data. 131 * @pdev: platform device to calculate for 132 * @wanted: The cycle time needed in nanoseconds. 133 * @clk: The input clock rate in kHz. 134 * @max: The maximum divider value that can be programmed. 135 * 136 * On success, returns the calculated timing value minus 1 for easy 137 * programming into AEMIF timing registers, else negative errno. 138 */ 139 static int aemif_calc_rate(struct platform_device *pdev, int wanted, 140 unsigned long clk, int max) 141 { 142 int result; 143 144 result = DIV_ROUND_UP((wanted * clk), NSEC_PER_MSEC) - 1; 145 146 dev_dbg(&pdev->dev, "%s: result %d from %ld, %d\n", __func__, result, 147 clk, wanted); 148 149 /* It is generally OK to have a more relaxed timing than requested... */ 150 if (result < 0) 151 result = 0; 152 153 /* ... But configuring tighter timings is not an option. */ 154 else if (result > max) 155 result = -EINVAL; 156 157 return result; 158 } 159 160 /** 161 * aemif_config_abus - configure async bus parameters 162 * @pdev: platform device to configure for 163 * @csnum: aemif chip select number 164 * 165 * This function programs the given timing values (in real clock) into the 166 * AEMIF registers taking the AEMIF clock into account. 167 * 168 * This function does not use any locking while programming the AEMIF 169 * because it is expected that there is only one user of a given 170 * chip-select. 171 * 172 * Returns 0 on success, else negative errno. 173 */ 174 static int aemif_config_abus(struct platform_device *pdev, int csnum) 175 { 176 struct aemif_device *aemif = platform_get_drvdata(pdev); 177 struct aemif_cs_data *data = &aemif->cs_data[csnum]; 178 int ta, rhold, rstrobe, rsetup, whold, wstrobe, wsetup; 179 unsigned long clk_rate = aemif->clk_rate; 180 unsigned offset; 181 u32 set, val; 182 183 offset = A1CR_OFFSET + (data->cs - aemif->cs_offset) * 4; 184 185 ta = aemif_calc_rate(pdev, data->ta, clk_rate, TA_MAX); 186 rhold = aemif_calc_rate(pdev, data->rhold, clk_rate, RHOLD_MAX); 187 rstrobe = aemif_calc_rate(pdev, data->rstrobe, clk_rate, RSTROBE_MAX); 188 rsetup = aemif_calc_rate(pdev, data->rsetup, clk_rate, RSETUP_MAX); 189 whold = aemif_calc_rate(pdev, data->whold, clk_rate, WHOLD_MAX); 190 wstrobe = aemif_calc_rate(pdev, data->wstrobe, clk_rate, WSTROBE_MAX); 191 wsetup = aemif_calc_rate(pdev, data->wsetup, clk_rate, WSETUP_MAX); 192 193 if (ta < 0 || rhold < 0 || rstrobe < 0 || rsetup < 0 || 194 whold < 0 || wstrobe < 0 || wsetup < 0) { 195 dev_err(&pdev->dev, "%s: cannot get suitable timings\n", 196 __func__); 197 return -EINVAL; 198 } 199 200 set = TA(ta) | RHOLD(rhold) | RSTROBE(rstrobe) | RSETUP(rsetup) | 201 WHOLD(whold) | WSTROBE(wstrobe) | WSETUP(wsetup); 202 203 set |= (data->asize & ACR_ASIZE_MASK); 204 if (data->enable_ew) 205 set |= ACR_EW_MASK; 206 if (data->enable_ss) 207 set |= ACR_SSTROBE_MASK; 208 209 val = readl(aemif->base + offset); 210 val &= ~CONFIG_MASK; 211 val |= set; 212 writel(val, aemif->base + offset); 213 214 return 0; 215 } 216 217 static inline int aemif_cycles_to_nsec(int val, unsigned long clk_rate) 218 { 219 return ((val + 1) * NSEC_PER_MSEC) / clk_rate; 220 } 221 222 /** 223 * aemif_get_hw_params - function to read hw register values 224 * @pdev: platform device to read for 225 * @csnum: aemif chip select number 226 * 227 * This function reads the defaults from the registers and update 228 * the timing values. Required for get/set commands and also for 229 * the case when driver needs to use defaults in hardware. 230 */ 231 static void aemif_get_hw_params(struct platform_device *pdev, int csnum) 232 { 233 struct aemif_device *aemif = platform_get_drvdata(pdev); 234 struct aemif_cs_data *data = &aemif->cs_data[csnum]; 235 unsigned long clk_rate = aemif->clk_rate; 236 u32 val, offset; 237 238 offset = A1CR_OFFSET + (data->cs - aemif->cs_offset) * 4; 239 val = readl(aemif->base + offset); 240 241 data->ta = aemif_cycles_to_nsec(TA_VAL(val), clk_rate); 242 data->rhold = aemif_cycles_to_nsec(RHOLD_VAL(val), clk_rate); 243 data->rstrobe = aemif_cycles_to_nsec(RSTROBE_VAL(val), clk_rate); 244 data->rsetup = aemif_cycles_to_nsec(RSETUP_VAL(val), clk_rate); 245 data->whold = aemif_cycles_to_nsec(WHOLD_VAL(val), clk_rate); 246 data->wstrobe = aemif_cycles_to_nsec(WSTROBE_VAL(val), clk_rate); 247 data->wsetup = aemif_cycles_to_nsec(WSETUP_VAL(val), clk_rate); 248 data->enable_ew = EW_VAL(val); 249 data->enable_ss = SSTROBE_VAL(val); 250 data->asize = val & ASIZE_MAX; 251 } 252 253 /** 254 * of_aemif_parse_abus_config - parse CS configuration from DT 255 * @pdev: platform device to parse for 256 * @np: device node ptr 257 * 258 * This function update the emif async bus configuration based on the values 259 * configured in a cs device binding node. 260 */ 261 static int of_aemif_parse_abus_config(struct platform_device *pdev, 262 struct device_node *np) 263 { 264 struct aemif_device *aemif = platform_get_drvdata(pdev); 265 struct aemif_cs_data *data; 266 u32 cs; 267 u32 val; 268 269 if (of_property_read_u32(np, "ti,cs-chipselect", &cs)) { 270 dev_dbg(&pdev->dev, "cs property is required"); 271 return -EINVAL; 272 } 273 274 if (cs - aemif->cs_offset >= NUM_CS || cs < aemif->cs_offset) { 275 dev_dbg(&pdev->dev, "cs number is incorrect %d", cs); 276 return -EINVAL; 277 } 278 279 if (aemif->num_cs >= NUM_CS) { 280 dev_dbg(&pdev->dev, "cs count is more than %d", NUM_CS); 281 return -EINVAL; 282 } 283 284 data = &aemif->cs_data[aemif->num_cs]; 285 data->cs = cs; 286 287 /* read the current value in the hw register */ 288 aemif_get_hw_params(pdev, aemif->num_cs++); 289 290 /* override the values from device node */ 291 if (!of_property_read_u32(np, "ti,cs-min-turnaround-ns", &val)) 292 data->ta = val; 293 294 if (!of_property_read_u32(np, "ti,cs-read-hold-ns", &val)) 295 data->rhold = val; 296 297 if (!of_property_read_u32(np, "ti,cs-read-strobe-ns", &val)) 298 data->rstrobe = val; 299 300 if (!of_property_read_u32(np, "ti,cs-read-setup-ns", &val)) 301 data->rsetup = val; 302 303 if (!of_property_read_u32(np, "ti,cs-write-hold-ns", &val)) 304 data->whold = val; 305 306 if (!of_property_read_u32(np, "ti,cs-write-strobe-ns", &val)) 307 data->wstrobe = val; 308 309 if (!of_property_read_u32(np, "ti,cs-write-setup-ns", &val)) 310 data->wsetup = val; 311 312 if (!of_property_read_u32(np, "ti,cs-bus-width", &val)) 313 if (val == 16) 314 data->asize = 1; 315 data->enable_ew = of_property_read_bool(np, "ti,cs-extended-wait-mode"); 316 data->enable_ss = of_property_read_bool(np, "ti,cs-select-strobe-mode"); 317 return 0; 318 } 319 320 static const struct of_device_id aemif_of_match[] = { 321 { .compatible = "ti,davinci-aemif", }, 322 { .compatible = "ti,da850-aemif", }, 323 {}, 324 }; 325 MODULE_DEVICE_TABLE(of, aemif_of_match); 326 327 static int aemif_probe(struct platform_device *pdev) 328 { 329 int i; 330 int ret = -ENODEV; 331 struct device *dev = &pdev->dev; 332 struct device_node *np = dev->of_node; 333 struct device_node *child_np; 334 struct aemif_device *aemif; 335 struct aemif_platform_data *pdata; 336 struct of_dev_auxdata *dev_lookup; 337 338 aemif = devm_kzalloc(dev, sizeof(*aemif), GFP_KERNEL); 339 if (!aemif) 340 return -ENOMEM; 341 342 pdata = dev_get_platdata(&pdev->dev); 343 dev_lookup = pdata ? pdata->dev_lookup : NULL; 344 345 platform_set_drvdata(pdev, aemif); 346 347 aemif->clk = devm_clk_get(dev, NULL); 348 if (IS_ERR(aemif->clk)) { 349 dev_err(dev, "cannot get clock 'aemif'\n"); 350 return PTR_ERR(aemif->clk); 351 } 352 353 ret = clk_prepare_enable(aemif->clk); 354 if (ret) 355 return ret; 356 357 aemif->clk_rate = clk_get_rate(aemif->clk) / MSEC_PER_SEC; 358 359 if (np && of_device_is_compatible(np, "ti,da850-aemif")) 360 aemif->cs_offset = 2; 361 else if (pdata) 362 aemif->cs_offset = pdata->cs_offset; 363 364 aemif->base = devm_platform_ioremap_resource(pdev, 0); 365 if (IS_ERR(aemif->base)) { 366 ret = PTR_ERR(aemif->base); 367 goto error; 368 } 369 370 if (np) { 371 /* 372 * For every controller device node, there is a cs device node 373 * that describe the bus configuration parameters. This 374 * functions iterate over these nodes and update the cs data 375 * array. 376 */ 377 for_each_available_child_of_node(np, child_np) { 378 ret = of_aemif_parse_abus_config(pdev, child_np); 379 if (ret < 0) { 380 of_node_put(child_np); 381 goto error; 382 } 383 } 384 } else if (pdata && pdata->num_abus_data > 0) { 385 for (i = 0; i < pdata->num_abus_data; i++, aemif->num_cs++) { 386 aemif->cs_data[i].cs = pdata->abus_data[i].cs; 387 aemif_get_hw_params(pdev, i); 388 } 389 } 390 391 for (i = 0; i < aemif->num_cs; i++) { 392 ret = aemif_config_abus(pdev, i); 393 if (ret < 0) { 394 dev_err(dev, "Error configuring chip select %d\n", 395 aemif->cs_data[i].cs); 396 goto error; 397 } 398 } 399 400 /* 401 * Create a child devices explicitly from here to guarantee that the 402 * child will be probed after the AEMIF timing parameters are set. 403 */ 404 if (np) { 405 for_each_available_child_of_node(np, child_np) { 406 ret = of_platform_populate(child_np, NULL, 407 dev_lookup, dev); 408 if (ret < 0) { 409 of_node_put(child_np); 410 goto error; 411 } 412 } 413 } else if (pdata) { 414 for (i = 0; i < pdata->num_sub_devices; i++) { 415 pdata->sub_devices[i].dev.parent = dev; 416 ret = platform_device_register(&pdata->sub_devices[i]); 417 if (ret) { 418 dev_warn(dev, "Error register sub device %s\n", 419 pdata->sub_devices[i].name); 420 } 421 } 422 } 423 424 return 0; 425 error: 426 clk_disable_unprepare(aemif->clk); 427 return ret; 428 } 429 430 static int aemif_remove(struct platform_device *pdev) 431 { 432 struct aemif_device *aemif = platform_get_drvdata(pdev); 433 434 clk_disable_unprepare(aemif->clk); 435 return 0; 436 } 437 438 static struct platform_driver aemif_driver = { 439 .probe = aemif_probe, 440 .remove = aemif_remove, 441 .driver = { 442 .name = "ti-aemif", 443 .of_match_table = of_match_ptr(aemif_of_match), 444 }, 445 }; 446 447 module_platform_driver(aemif_driver); 448 449 MODULE_AUTHOR("Murali Karicheri <m-karicheri2@ti.com>"); 450 MODULE_AUTHOR("Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>"); 451 MODULE_DESCRIPTION("Texas Instruments AEMIF driver"); 452 MODULE_LICENSE("GPL v2"); 453 MODULE_ALIAS("platform:" KBUILD_MODNAME); 454