1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * TI Camera Access Layer (CAL) - CAMERARX 4 * 5 * Copyright (c) 2015-2020 Texas Instruments Inc. 6 * 7 * Authors: 8 * Benoit Parrot <bparrot@ti.com> 9 * Laurent Pinchart <laurent.pinchart@ideasonboard.com> 10 */ 11 12 #include <linux/clk.h> 13 #include <linux/delay.h> 14 #include <linux/mfd/syscon.h> 15 #include <linux/module.h> 16 #include <linux/of_graph.h> 17 #include <linux/platform_device.h> 18 #include <linux/regmap.h> 19 #include <linux/slab.h> 20 21 #include <media/v4l2-ctrls.h> 22 #include <media/v4l2-fwnode.h> 23 #include <media/v4l2-subdev.h> 24 25 #include "cal.h" 26 #include "cal_regs.h" 27 28 /* ------------------------------------------------------------------ 29 * I/O Register Accessors 30 * ------------------------------------------------------------------ 31 */ 32 33 static inline u32 camerarx_read(struct cal_camerarx *phy, u32 offset) 34 { 35 return ioread32(phy->base + offset); 36 } 37 38 static inline void camerarx_write(struct cal_camerarx *phy, u32 offset, u32 val) 39 { 40 iowrite32(val, phy->base + offset); 41 } 42 43 /* ------------------------------------------------------------------ 44 * CAMERARX Management 45 * ------------------------------------------------------------------ 46 */ 47 48 static s64 cal_camerarx_get_ext_link_freq(struct cal_camerarx *phy) 49 { 50 struct v4l2_mbus_config_mipi_csi2 *mipi_csi2 = &phy->endpoint.bus.mipi_csi2; 51 u32 num_lanes = mipi_csi2->num_data_lanes; 52 const struct cal_format_info *fmtinfo; 53 u32 bpp; 54 s64 freq; 55 56 fmtinfo = cal_format_by_code(phy->formats[CAL_CAMERARX_PAD_SINK].code); 57 if (!fmtinfo) 58 return -EINVAL; 59 60 bpp = fmtinfo->bpp; 61 62 freq = v4l2_get_link_freq(phy->source->ctrl_handler, bpp, 2 * num_lanes); 63 if (freq < 0) { 64 phy_err(phy, "failed to get link freq for subdev '%s'\n", 65 phy->source->name); 66 return freq; 67 } 68 69 phy_dbg(3, phy, "Source Link Freq: %llu\n", freq); 70 71 return freq; 72 } 73 74 static void cal_camerarx_lane_config(struct cal_camerarx *phy) 75 { 76 u32 val = cal_read(phy->cal, CAL_CSI2_COMPLEXIO_CFG(phy->instance)); 77 u32 lane_mask = CAL_CSI2_COMPLEXIO_CFG_CLOCK_POSITION_MASK; 78 u32 polarity_mask = CAL_CSI2_COMPLEXIO_CFG_CLOCK_POL_MASK; 79 struct v4l2_mbus_config_mipi_csi2 *mipi_csi2 = 80 &phy->endpoint.bus.mipi_csi2; 81 int lane; 82 83 cal_set_field(&val, mipi_csi2->clock_lane + 1, lane_mask); 84 cal_set_field(&val, mipi_csi2->lane_polarities[0], polarity_mask); 85 for (lane = 0; lane < mipi_csi2->num_data_lanes; lane++) { 86 /* 87 * Every lane are one nibble apart starting with the 88 * clock followed by the data lanes so shift masks by 4. 89 */ 90 lane_mask <<= 4; 91 polarity_mask <<= 4; 92 cal_set_field(&val, mipi_csi2->data_lanes[lane] + 1, lane_mask); 93 cal_set_field(&val, mipi_csi2->lane_polarities[lane + 1], 94 polarity_mask); 95 } 96 97 cal_write(phy->cal, CAL_CSI2_COMPLEXIO_CFG(phy->instance), val); 98 phy_dbg(3, phy, "CAL_CSI2_COMPLEXIO_CFG(%d) = 0x%08x\n", 99 phy->instance, val); 100 } 101 102 static void cal_camerarx_enable(struct cal_camerarx *phy) 103 { 104 u32 num_lanes = phy->cal->data->camerarx[phy->instance].num_lanes; 105 106 regmap_field_write(phy->fields[F_CAMMODE], 0); 107 /* Always enable all lanes at the phy control level */ 108 regmap_field_write(phy->fields[F_LANEENABLE], (1 << num_lanes) - 1); 109 /* F_CSI_MODE is not present on every architecture */ 110 if (phy->fields[F_CSI_MODE]) 111 regmap_field_write(phy->fields[F_CSI_MODE], 1); 112 regmap_field_write(phy->fields[F_CTRLCLKEN], 1); 113 } 114 115 void cal_camerarx_disable(struct cal_camerarx *phy) 116 { 117 regmap_field_write(phy->fields[F_CTRLCLKEN], 0); 118 } 119 120 /* 121 * TCLK values are OK at their reset values 122 */ 123 #define TCLK_TERM 0 124 #define TCLK_MISS 1 125 #define TCLK_SETTLE 14 126 127 static void cal_camerarx_config(struct cal_camerarx *phy, s64 link_freq) 128 { 129 unsigned int reg0, reg1; 130 unsigned int ths_term, ths_settle; 131 132 /* DPHY timing configuration */ 133 134 /* THS_TERM: Programmed value = floor(20 ns/DDRClk period) */ 135 ths_term = div_s64(20 * link_freq, 1000 * 1000 * 1000); 136 phy_dbg(1, phy, "ths_term: %d (0x%02x)\n", ths_term, ths_term); 137 138 /* THS_SETTLE: Programmed value = floor(105 ns/DDRClk period) + 4 */ 139 ths_settle = div_s64(105 * link_freq, 1000 * 1000 * 1000) + 4; 140 phy_dbg(1, phy, "ths_settle: %d (0x%02x)\n", ths_settle, ths_settle); 141 142 reg0 = camerarx_read(phy, CAL_CSI2_PHY_REG0); 143 cal_set_field(®0, CAL_CSI2_PHY_REG0_HSCLOCKCONFIG_DISABLE, 144 CAL_CSI2_PHY_REG0_HSCLOCKCONFIG_MASK); 145 cal_set_field(®0, ths_term, CAL_CSI2_PHY_REG0_THS_TERM_MASK); 146 cal_set_field(®0, ths_settle, CAL_CSI2_PHY_REG0_THS_SETTLE_MASK); 147 148 phy_dbg(1, phy, "CSI2_%d_REG0 = 0x%08x\n", phy->instance, reg0); 149 camerarx_write(phy, CAL_CSI2_PHY_REG0, reg0); 150 151 reg1 = camerarx_read(phy, CAL_CSI2_PHY_REG1); 152 cal_set_field(®1, TCLK_TERM, CAL_CSI2_PHY_REG1_TCLK_TERM_MASK); 153 cal_set_field(®1, 0xb8, CAL_CSI2_PHY_REG1_DPHY_HS_SYNC_PATTERN_MASK); 154 cal_set_field(®1, TCLK_MISS, 155 CAL_CSI2_PHY_REG1_CTRLCLK_DIV_FACTOR_MASK); 156 cal_set_field(®1, TCLK_SETTLE, CAL_CSI2_PHY_REG1_TCLK_SETTLE_MASK); 157 158 phy_dbg(1, phy, "CSI2_%d_REG1 = 0x%08x\n", phy->instance, reg1); 159 camerarx_write(phy, CAL_CSI2_PHY_REG1, reg1); 160 } 161 162 static void cal_camerarx_power(struct cal_camerarx *phy, bool enable) 163 { 164 u32 target_state; 165 unsigned int i; 166 167 target_state = enable ? CAL_CSI2_COMPLEXIO_CFG_PWR_CMD_STATE_ON : 168 CAL_CSI2_COMPLEXIO_CFG_PWR_CMD_STATE_OFF; 169 170 cal_write_field(phy->cal, CAL_CSI2_COMPLEXIO_CFG(phy->instance), 171 target_state, CAL_CSI2_COMPLEXIO_CFG_PWR_CMD_MASK); 172 173 for (i = 0; i < 10; i++) { 174 u32 current_state; 175 176 current_state = cal_read_field(phy->cal, 177 CAL_CSI2_COMPLEXIO_CFG(phy->instance), 178 CAL_CSI2_COMPLEXIO_CFG_PWR_STATUS_MASK); 179 180 if (current_state == target_state) 181 break; 182 183 usleep_range(1000, 1100); 184 } 185 186 if (i == 10) 187 phy_err(phy, "Failed to power %s complexio\n", 188 enable ? "up" : "down"); 189 } 190 191 static void cal_camerarx_wait_reset(struct cal_camerarx *phy) 192 { 193 unsigned long timeout; 194 195 timeout = jiffies + msecs_to_jiffies(750); 196 while (time_before(jiffies, timeout)) { 197 if (cal_read_field(phy->cal, 198 CAL_CSI2_COMPLEXIO_CFG(phy->instance), 199 CAL_CSI2_COMPLEXIO_CFG_RESET_DONE_MASK) == 200 CAL_CSI2_COMPLEXIO_CFG_RESET_DONE_RESETCOMPLETED) 201 break; 202 usleep_range(500, 5000); 203 } 204 205 if (cal_read_field(phy->cal, CAL_CSI2_COMPLEXIO_CFG(phy->instance), 206 CAL_CSI2_COMPLEXIO_CFG_RESET_DONE_MASK) != 207 CAL_CSI2_COMPLEXIO_CFG_RESET_DONE_RESETCOMPLETED) 208 phy_err(phy, "Timeout waiting for Complex IO reset done\n"); 209 } 210 211 static void cal_camerarx_wait_stop_state(struct cal_camerarx *phy) 212 { 213 unsigned long timeout; 214 215 timeout = jiffies + msecs_to_jiffies(750); 216 while (time_before(jiffies, timeout)) { 217 if (cal_read_field(phy->cal, 218 CAL_CSI2_TIMING(phy->instance), 219 CAL_CSI2_TIMING_FORCE_RX_MODE_IO1_MASK) == 0) 220 break; 221 usleep_range(500, 5000); 222 } 223 224 if (cal_read_field(phy->cal, CAL_CSI2_TIMING(phy->instance), 225 CAL_CSI2_TIMING_FORCE_RX_MODE_IO1_MASK) != 0) 226 phy_err(phy, "Timeout waiting for stop state\n"); 227 } 228 229 static void cal_camerarx_enable_irqs(struct cal_camerarx *phy) 230 { 231 const u32 cio_err_mask = 232 CAL_CSI2_COMPLEXIO_IRQ_LANE_ERRORS_MASK | 233 CAL_CSI2_COMPLEXIO_IRQ_FIFO_OVR_MASK | 234 CAL_CSI2_COMPLEXIO_IRQ_SHORT_PACKET_MASK | 235 CAL_CSI2_COMPLEXIO_IRQ_ECC_NO_CORRECTION_MASK; 236 const u32 vc_err_mask = 237 CAL_CSI2_VC_IRQ_CS_IRQ_MASK(0) | 238 CAL_CSI2_VC_IRQ_CS_IRQ_MASK(1) | 239 CAL_CSI2_VC_IRQ_CS_IRQ_MASK(2) | 240 CAL_CSI2_VC_IRQ_CS_IRQ_MASK(3) | 241 CAL_CSI2_VC_IRQ_ECC_CORRECTION_IRQ_MASK(0) | 242 CAL_CSI2_VC_IRQ_ECC_CORRECTION_IRQ_MASK(1) | 243 CAL_CSI2_VC_IRQ_ECC_CORRECTION_IRQ_MASK(2) | 244 CAL_CSI2_VC_IRQ_ECC_CORRECTION_IRQ_MASK(3); 245 246 /* Enable CIO & VC error IRQs. */ 247 cal_write(phy->cal, CAL_HL_IRQENABLE_SET(0), 248 CAL_HL_IRQ_CIO_MASK(phy->instance) | 249 CAL_HL_IRQ_VC_MASK(phy->instance)); 250 cal_write(phy->cal, CAL_CSI2_COMPLEXIO_IRQENABLE(phy->instance), 251 cio_err_mask); 252 cal_write(phy->cal, CAL_CSI2_VC_IRQENABLE(phy->instance), 253 vc_err_mask); 254 } 255 256 static void cal_camerarx_disable_irqs(struct cal_camerarx *phy) 257 { 258 /* Disable CIO error irqs */ 259 cal_write(phy->cal, CAL_HL_IRQENABLE_CLR(0), 260 CAL_HL_IRQ_CIO_MASK(phy->instance) | 261 CAL_HL_IRQ_VC_MASK(phy->instance)); 262 cal_write(phy->cal, CAL_CSI2_COMPLEXIO_IRQENABLE(phy->instance), 0); 263 cal_write(phy->cal, CAL_CSI2_VC_IRQENABLE(phy->instance), 0); 264 } 265 266 static void cal_camerarx_ppi_enable(struct cal_camerarx *phy) 267 { 268 cal_write_field(phy->cal, CAL_CSI2_PPI_CTRL(phy->instance), 269 1, CAL_CSI2_PPI_CTRL_ECC_EN_MASK); 270 271 cal_write_field(phy->cal, CAL_CSI2_PPI_CTRL(phy->instance), 272 1, CAL_CSI2_PPI_CTRL_IF_EN_MASK); 273 } 274 275 static void cal_camerarx_ppi_disable(struct cal_camerarx *phy) 276 { 277 cal_write_field(phy->cal, CAL_CSI2_PPI_CTRL(phy->instance), 278 0, CAL_CSI2_PPI_CTRL_IF_EN_MASK); 279 } 280 281 static int cal_camerarx_start(struct cal_camerarx *phy) 282 { 283 s64 link_freq; 284 u32 sscounter; 285 u32 val; 286 int ret; 287 288 if (phy->enable_count > 0) { 289 phy->enable_count++; 290 return 0; 291 } 292 293 link_freq = cal_camerarx_get_ext_link_freq(phy); 294 if (link_freq < 0) 295 return link_freq; 296 297 ret = v4l2_subdev_call(phy->source, core, s_power, 1); 298 if (ret < 0 && ret != -ENOIOCTLCMD && ret != -ENODEV) { 299 phy_err(phy, "power on failed in subdev\n"); 300 return ret; 301 } 302 303 cal_camerarx_enable_irqs(phy); 304 305 /* 306 * CSI-2 PHY Link Initialization Sequence, according to the DRA74xP / 307 * DRA75xP / DRA76xP / DRA77xP TRM. The DRA71x / DRA72x and the AM65x / 308 * DRA80xM TRMs have a slightly simplified sequence. 309 */ 310 311 /* 312 * 1. Configure all CSI-2 low level protocol registers to be ready to 313 * receive signals/data from the CSI-2 PHY. 314 * 315 * i.-v. Configure the lanes position and polarity. 316 */ 317 cal_camerarx_lane_config(phy); 318 319 /* 320 * vi.-vii. Configure D-PHY mode, enable the required lanes and 321 * enable the CAMERARX clock. 322 */ 323 cal_camerarx_enable(phy); 324 325 /* 326 * 2. CSI PHY and link initialization sequence. 327 * 328 * a. Deassert the CSI-2 PHY reset. Do not wait for reset completion 329 * at this point, as it requires the external source to send the 330 * CSI-2 HS clock. 331 */ 332 cal_write_field(phy->cal, CAL_CSI2_COMPLEXIO_CFG(phy->instance), 333 CAL_CSI2_COMPLEXIO_CFG_RESET_CTRL_OPERATIONAL, 334 CAL_CSI2_COMPLEXIO_CFG_RESET_CTRL_MASK); 335 phy_dbg(3, phy, "CAL_CSI2_COMPLEXIO_CFG(%d) = 0x%08x De-assert Complex IO Reset\n", 336 phy->instance, 337 cal_read(phy->cal, CAL_CSI2_COMPLEXIO_CFG(phy->instance))); 338 339 /* Dummy read to allow SCP reset to complete. */ 340 camerarx_read(phy, CAL_CSI2_PHY_REG0); 341 342 /* Program the PHY timing parameters. */ 343 cal_camerarx_config(phy, link_freq); 344 345 /* 346 * b. Assert the FORCERXMODE signal. 347 * 348 * The stop-state-counter is based on fclk cycles, and we always use 349 * the x16 and x4 settings, so stop-state-timeout = 350 * fclk-cycle * 16 * 4 * counter. 351 * 352 * Stop-state-timeout must be more than 100us as per CSI-2 spec, so we 353 * calculate a timeout that's 100us (rounding up). 354 */ 355 sscounter = DIV_ROUND_UP(clk_get_rate(phy->cal->fclk), 10000 * 16 * 4); 356 357 val = cal_read(phy->cal, CAL_CSI2_TIMING(phy->instance)); 358 cal_set_field(&val, 1, CAL_CSI2_TIMING_STOP_STATE_X16_IO1_MASK); 359 cal_set_field(&val, 1, CAL_CSI2_TIMING_STOP_STATE_X4_IO1_MASK); 360 cal_set_field(&val, sscounter, 361 CAL_CSI2_TIMING_STOP_STATE_COUNTER_IO1_MASK); 362 cal_write(phy->cal, CAL_CSI2_TIMING(phy->instance), val); 363 phy_dbg(3, phy, "CAL_CSI2_TIMING(%d) = 0x%08x Stop States\n", 364 phy->instance, 365 cal_read(phy->cal, CAL_CSI2_TIMING(phy->instance))); 366 367 /* Assert the FORCERXMODE signal. */ 368 cal_write_field(phy->cal, CAL_CSI2_TIMING(phy->instance), 369 1, CAL_CSI2_TIMING_FORCE_RX_MODE_IO1_MASK); 370 phy_dbg(3, phy, "CAL_CSI2_TIMING(%d) = 0x%08x Force RXMODE\n", 371 phy->instance, 372 cal_read(phy->cal, CAL_CSI2_TIMING(phy->instance))); 373 374 /* 375 * c. Connect pull-down on CSI-2 PHY link (using pad control). 376 * 377 * This is not required on DRA71x, DRA72x, AM65x and DRA80xM. Not 378 * implemented. 379 */ 380 381 /* 382 * d. Power up the CSI-2 PHY. 383 * e. Check whether the state status reaches the ON state. 384 */ 385 cal_camerarx_power(phy, true); 386 387 /* 388 * Start the source to enable the CSI-2 HS clock. We can now wait for 389 * CSI-2 PHY reset to complete. 390 */ 391 ret = v4l2_subdev_call(phy->source, video, s_stream, 1); 392 if (ret) { 393 v4l2_subdev_call(phy->source, core, s_power, 0); 394 cal_camerarx_disable_irqs(phy); 395 phy_err(phy, "stream on failed in subdev\n"); 396 return ret; 397 } 398 399 cal_camerarx_wait_reset(phy); 400 401 /* f. Wait for STOPSTATE=1 for all enabled lane modules. */ 402 cal_camerarx_wait_stop_state(phy); 403 404 phy_dbg(1, phy, "CSI2_%u_REG1 = 0x%08x (bits 31-28 should be set)\n", 405 phy->instance, camerarx_read(phy, CAL_CSI2_PHY_REG1)); 406 407 /* 408 * g. Disable pull-down on CSI-2 PHY link (using pad control). 409 * 410 * This is not required on DRA71x, DRA72x, AM65x and DRA80xM. Not 411 * implemented. 412 */ 413 414 /* Finally, enable the PHY Protocol Interface (PPI). */ 415 cal_camerarx_ppi_enable(phy); 416 417 phy->enable_count++; 418 419 return 0; 420 } 421 422 static void cal_camerarx_stop(struct cal_camerarx *phy) 423 { 424 int ret; 425 426 if (--phy->enable_count > 0) 427 return; 428 429 cal_camerarx_ppi_disable(phy); 430 431 cal_camerarx_disable_irqs(phy); 432 433 cal_camerarx_power(phy, false); 434 435 /* Assert Complex IO Reset */ 436 cal_write_field(phy->cal, CAL_CSI2_COMPLEXIO_CFG(phy->instance), 437 CAL_CSI2_COMPLEXIO_CFG_RESET_CTRL, 438 CAL_CSI2_COMPLEXIO_CFG_RESET_CTRL_MASK); 439 440 phy_dbg(3, phy, "CAL_CSI2_COMPLEXIO_CFG(%d) = 0x%08x Complex IO in Reset\n", 441 phy->instance, 442 cal_read(phy->cal, CAL_CSI2_COMPLEXIO_CFG(phy->instance))); 443 444 /* Disable the phy */ 445 cal_camerarx_disable(phy); 446 447 if (v4l2_subdev_call(phy->source, video, s_stream, 0)) 448 phy_err(phy, "stream off failed in subdev\n"); 449 450 ret = v4l2_subdev_call(phy->source, core, s_power, 0); 451 if (ret < 0 && ret != -ENOIOCTLCMD && ret != -ENODEV) 452 phy_err(phy, "power off failed in subdev\n"); 453 } 454 455 /* 456 * Errata i913: CSI2 LDO Needs to be disabled when module is powered on 457 * 458 * Enabling CSI2 LDO shorts it to core supply. It is crucial the 2 CSI2 459 * LDOs on the device are disabled if CSI-2 module is powered on 460 * (0x4845 B304 | 0x4845 B384 [28:27] = 0x1) or in ULPS (0x4845 B304 461 * | 0x4845 B384 [28:27] = 0x2) mode. Common concerns include: high 462 * current draw on the module supply in active mode. 463 * 464 * Errata does not apply when CSI-2 module is powered off 465 * (0x4845 B304 | 0x4845 B384 [28:27] = 0x0). 466 * 467 * SW Workaround: 468 * Set the following register bits to disable the LDO, 469 * which is essentially CSI2 REG10 bit 6: 470 * 471 * Core 0: 0x4845 B828 = 0x0000 0040 472 * Core 1: 0x4845 B928 = 0x0000 0040 473 */ 474 void cal_camerarx_i913_errata(struct cal_camerarx *phy) 475 { 476 u32 reg10 = camerarx_read(phy, CAL_CSI2_PHY_REG10); 477 478 cal_set_field(®10, 1, CAL_CSI2_PHY_REG10_I933_LDO_DISABLE_MASK); 479 480 phy_dbg(1, phy, "CSI2_%d_REG10 = 0x%08x\n", phy->instance, reg10); 481 camerarx_write(phy, CAL_CSI2_PHY_REG10, reg10); 482 } 483 484 static int cal_camerarx_regmap_init(struct cal_dev *cal, 485 struct cal_camerarx *phy) 486 { 487 const struct cal_camerarx_data *phy_data; 488 unsigned int i; 489 490 if (!cal->data) 491 return -EINVAL; 492 493 phy_data = &cal->data->camerarx[phy->instance]; 494 495 for (i = 0; i < F_MAX_FIELDS; i++) { 496 struct reg_field field = { 497 .reg = cal->syscon_camerrx_offset, 498 .lsb = phy_data->fields[i].lsb, 499 .msb = phy_data->fields[i].msb, 500 }; 501 502 /* 503 * Here we update the reg offset with the 504 * value found in DT 505 */ 506 phy->fields[i] = devm_regmap_field_alloc(cal->dev, 507 cal->syscon_camerrx, 508 field); 509 if (IS_ERR(phy->fields[i])) { 510 cal_err(cal, "Unable to allocate regmap fields\n"); 511 return PTR_ERR(phy->fields[i]); 512 } 513 } 514 515 return 0; 516 } 517 518 static int cal_camerarx_parse_dt(struct cal_camerarx *phy) 519 { 520 struct v4l2_fwnode_endpoint *endpoint = &phy->endpoint; 521 char data_lanes[V4L2_MBUS_CSI2_MAX_DATA_LANES * 2]; 522 struct device_node *ep_node; 523 unsigned int i; 524 int ret; 525 526 /* 527 * Find the endpoint node for the port corresponding to the PHY 528 * instance, and parse its CSI-2-related properties. 529 */ 530 ep_node = of_graph_get_endpoint_by_regs(phy->cal->dev->of_node, 531 phy->instance, 0); 532 if (!ep_node) { 533 /* 534 * The endpoint is not mandatory, not all PHY instances need to 535 * be connected in DT. 536 */ 537 phy_dbg(3, phy, "Port has no endpoint\n"); 538 return 0; 539 } 540 541 endpoint->bus_type = V4L2_MBUS_CSI2_DPHY; 542 ret = v4l2_fwnode_endpoint_parse(of_fwnode_handle(ep_node), endpoint); 543 if (ret < 0) { 544 phy_err(phy, "Failed to parse endpoint\n"); 545 goto done; 546 } 547 548 for (i = 0; i < endpoint->bus.mipi_csi2.num_data_lanes; i++) { 549 unsigned int lane = endpoint->bus.mipi_csi2.data_lanes[i]; 550 551 if (lane > 4) { 552 phy_err(phy, "Invalid position %u for data lane %u\n", 553 lane, i); 554 ret = -EINVAL; 555 goto done; 556 } 557 558 data_lanes[i*2] = '0' + lane; 559 data_lanes[i*2+1] = ' '; 560 } 561 562 data_lanes[i*2-1] = '\0'; 563 564 phy_dbg(3, phy, 565 "CSI-2 bus: clock lane <%u>, data lanes <%s>, flags 0x%08x\n", 566 endpoint->bus.mipi_csi2.clock_lane, data_lanes, 567 endpoint->bus.mipi_csi2.flags); 568 569 /* Retrieve the connected device and store it for later use. */ 570 phy->source_ep_node = of_graph_get_remote_endpoint(ep_node); 571 phy->source_node = of_graph_get_port_parent(phy->source_ep_node); 572 if (!phy->source_node) { 573 phy_dbg(3, phy, "Can't get remote parent\n"); 574 of_node_put(phy->source_ep_node); 575 ret = -EINVAL; 576 goto done; 577 } 578 579 phy_dbg(1, phy, "Found connected device %pOFn\n", phy->source_node); 580 581 done: 582 of_node_put(ep_node); 583 return ret; 584 } 585 586 int cal_camerarx_get_remote_frame_desc(struct cal_camerarx *phy, 587 struct v4l2_mbus_frame_desc *desc) 588 { 589 struct media_pad *pad; 590 int ret; 591 592 if (!phy->source) 593 return -EPIPE; 594 595 pad = media_pad_remote_pad_first(&phy->pads[CAL_CAMERARX_PAD_SINK]); 596 if (!pad) 597 return -EPIPE; 598 599 ret = v4l2_subdev_call(phy->source, pad, get_frame_desc, pad->index, 600 desc); 601 if (ret) 602 return ret; 603 604 if (desc->type != V4L2_MBUS_FRAME_DESC_TYPE_CSI2) { 605 dev_err(phy->cal->dev, 606 "Frame descriptor does not describe CSI-2 link"); 607 return -EINVAL; 608 } 609 610 return 0; 611 } 612 613 /* ------------------------------------------------------------------ 614 * V4L2 Subdev Operations 615 * ------------------------------------------------------------------ 616 */ 617 618 static inline struct cal_camerarx *to_cal_camerarx(struct v4l2_subdev *sd) 619 { 620 return container_of(sd, struct cal_camerarx, subdev); 621 } 622 623 static struct v4l2_mbus_framefmt * 624 cal_camerarx_get_pad_format(struct cal_camerarx *phy, 625 struct v4l2_subdev_state *sd_state, 626 unsigned int pad, u32 which) 627 { 628 switch (which) { 629 case V4L2_SUBDEV_FORMAT_TRY: 630 return v4l2_subdev_get_try_format(&phy->subdev, sd_state, pad); 631 case V4L2_SUBDEV_FORMAT_ACTIVE: 632 return &phy->formats[pad]; 633 default: 634 return NULL; 635 } 636 } 637 638 static int cal_camerarx_sd_s_stream(struct v4l2_subdev *sd, int enable) 639 { 640 struct cal_camerarx *phy = to_cal_camerarx(sd); 641 int ret = 0; 642 643 mutex_lock(&phy->mutex); 644 645 if (enable) 646 ret = cal_camerarx_start(phy); 647 else 648 cal_camerarx_stop(phy); 649 650 mutex_unlock(&phy->mutex); 651 652 return ret; 653 } 654 655 static int cal_camerarx_sd_enum_mbus_code(struct v4l2_subdev *sd, 656 struct v4l2_subdev_state *sd_state, 657 struct v4l2_subdev_mbus_code_enum *code) 658 { 659 struct cal_camerarx *phy = to_cal_camerarx(sd); 660 int ret = 0; 661 662 mutex_lock(&phy->mutex); 663 664 /* No transcoding, source and sink codes must match. */ 665 if (cal_rx_pad_is_source(code->pad)) { 666 struct v4l2_mbus_framefmt *fmt; 667 668 if (code->index > 0) { 669 ret = -EINVAL; 670 goto out; 671 } 672 673 fmt = cal_camerarx_get_pad_format(phy, sd_state, 674 CAL_CAMERARX_PAD_SINK, 675 code->which); 676 code->code = fmt->code; 677 } else { 678 if (code->index >= cal_num_formats) { 679 ret = -EINVAL; 680 goto out; 681 } 682 683 code->code = cal_formats[code->index].code; 684 } 685 686 out: 687 mutex_unlock(&phy->mutex); 688 689 return ret; 690 } 691 692 static int cal_camerarx_sd_enum_frame_size(struct v4l2_subdev *sd, 693 struct v4l2_subdev_state *sd_state, 694 struct v4l2_subdev_frame_size_enum *fse) 695 { 696 struct cal_camerarx *phy = to_cal_camerarx(sd); 697 const struct cal_format_info *fmtinfo; 698 int ret = 0; 699 700 if (fse->index > 0) 701 return -EINVAL; 702 703 mutex_lock(&phy->mutex); 704 705 /* No transcoding, source and sink formats must match. */ 706 if (cal_rx_pad_is_source(fse->pad)) { 707 struct v4l2_mbus_framefmt *fmt; 708 709 fmt = cal_camerarx_get_pad_format(phy, sd_state, 710 CAL_CAMERARX_PAD_SINK, 711 fse->which); 712 if (fse->code != fmt->code) { 713 ret = -EINVAL; 714 goto out; 715 } 716 717 fse->min_width = fmt->width; 718 fse->max_width = fmt->width; 719 fse->min_height = fmt->height; 720 fse->max_height = fmt->height; 721 } else { 722 fmtinfo = cal_format_by_code(fse->code); 723 if (!fmtinfo) { 724 ret = -EINVAL; 725 goto out; 726 } 727 728 fse->min_width = CAL_MIN_WIDTH_BYTES * 8 / ALIGN(fmtinfo->bpp, 8); 729 fse->max_width = CAL_MAX_WIDTH_BYTES * 8 / ALIGN(fmtinfo->bpp, 8); 730 fse->min_height = CAL_MIN_HEIGHT_LINES; 731 fse->max_height = CAL_MAX_HEIGHT_LINES; 732 } 733 734 out: 735 mutex_unlock(&phy->mutex); 736 737 return ret; 738 } 739 740 static int cal_camerarx_sd_get_fmt(struct v4l2_subdev *sd, 741 struct v4l2_subdev_state *sd_state, 742 struct v4l2_subdev_format *format) 743 { 744 struct cal_camerarx *phy = to_cal_camerarx(sd); 745 struct v4l2_mbus_framefmt *fmt; 746 747 mutex_lock(&phy->mutex); 748 749 fmt = cal_camerarx_get_pad_format(phy, sd_state, format->pad, 750 format->which); 751 format->format = *fmt; 752 753 mutex_unlock(&phy->mutex); 754 755 return 0; 756 } 757 758 static int cal_camerarx_sd_set_fmt(struct v4l2_subdev *sd, 759 struct v4l2_subdev_state *sd_state, 760 struct v4l2_subdev_format *format) 761 { 762 struct cal_camerarx *phy = to_cal_camerarx(sd); 763 const struct cal_format_info *fmtinfo; 764 struct v4l2_mbus_framefmt *fmt; 765 unsigned int bpp; 766 767 /* No transcoding, source and sink formats must match. */ 768 if (cal_rx_pad_is_source(format->pad)) 769 return cal_camerarx_sd_get_fmt(sd, sd_state, format); 770 771 /* 772 * Default to the first format if the requested media bus code isn't 773 * supported. 774 */ 775 fmtinfo = cal_format_by_code(format->format.code); 776 if (!fmtinfo) 777 fmtinfo = &cal_formats[0]; 778 779 /* Clamp the size, update the code. The colorspace is accepted as-is. */ 780 bpp = ALIGN(fmtinfo->bpp, 8); 781 782 format->format.width = clamp_t(unsigned int, format->format.width, 783 CAL_MIN_WIDTH_BYTES * 8 / bpp, 784 CAL_MAX_WIDTH_BYTES * 8 / bpp); 785 format->format.height = clamp_t(unsigned int, format->format.height, 786 CAL_MIN_HEIGHT_LINES, 787 CAL_MAX_HEIGHT_LINES); 788 format->format.code = fmtinfo->code; 789 format->format.field = V4L2_FIELD_NONE; 790 791 /* Store the format and propagate it to the source pad. */ 792 793 mutex_lock(&phy->mutex); 794 795 fmt = cal_camerarx_get_pad_format(phy, sd_state, 796 CAL_CAMERARX_PAD_SINK, 797 format->which); 798 *fmt = format->format; 799 800 fmt = cal_camerarx_get_pad_format(phy, sd_state, 801 CAL_CAMERARX_PAD_FIRST_SOURCE, 802 format->which); 803 *fmt = format->format; 804 805 mutex_unlock(&phy->mutex); 806 807 return 0; 808 } 809 810 static int cal_camerarx_sd_init_cfg(struct v4l2_subdev *sd, 811 struct v4l2_subdev_state *sd_state) 812 { 813 struct v4l2_subdev_format format = { 814 .which = sd_state ? V4L2_SUBDEV_FORMAT_TRY 815 : V4L2_SUBDEV_FORMAT_ACTIVE, 816 .pad = CAL_CAMERARX_PAD_SINK, 817 .format = { 818 .width = 640, 819 .height = 480, 820 .code = MEDIA_BUS_FMT_UYVY8_2X8, 821 .field = V4L2_FIELD_NONE, 822 .colorspace = V4L2_COLORSPACE_SRGB, 823 .ycbcr_enc = V4L2_YCBCR_ENC_601, 824 .quantization = V4L2_QUANTIZATION_LIM_RANGE, 825 .xfer_func = V4L2_XFER_FUNC_SRGB, 826 }, 827 }; 828 829 return cal_camerarx_sd_set_fmt(sd, sd_state, &format); 830 } 831 832 static const struct v4l2_subdev_video_ops cal_camerarx_video_ops = { 833 .s_stream = cal_camerarx_sd_s_stream, 834 }; 835 836 static const struct v4l2_subdev_pad_ops cal_camerarx_pad_ops = { 837 .init_cfg = cal_camerarx_sd_init_cfg, 838 .enum_mbus_code = cal_camerarx_sd_enum_mbus_code, 839 .enum_frame_size = cal_camerarx_sd_enum_frame_size, 840 .get_fmt = cal_camerarx_sd_get_fmt, 841 .set_fmt = cal_camerarx_sd_set_fmt, 842 }; 843 844 static const struct v4l2_subdev_ops cal_camerarx_subdev_ops = { 845 .video = &cal_camerarx_video_ops, 846 .pad = &cal_camerarx_pad_ops, 847 }; 848 849 static struct media_entity_operations cal_camerarx_media_ops = { 850 .link_validate = v4l2_subdev_link_validate, 851 }; 852 853 /* ------------------------------------------------------------------ 854 * Create and Destroy 855 * ------------------------------------------------------------------ 856 */ 857 858 struct cal_camerarx *cal_camerarx_create(struct cal_dev *cal, 859 unsigned int instance) 860 { 861 struct platform_device *pdev = to_platform_device(cal->dev); 862 struct cal_camerarx *phy; 863 struct v4l2_subdev *sd; 864 unsigned int i; 865 int ret; 866 867 phy = kzalloc(sizeof(*phy), GFP_KERNEL); 868 if (!phy) 869 return ERR_PTR(-ENOMEM); 870 871 phy->cal = cal; 872 phy->instance = instance; 873 874 mutex_init(&phy->mutex); 875 876 phy->res = platform_get_resource_byname(pdev, IORESOURCE_MEM, 877 (instance == 0) ? 878 "cal_rx_core0" : 879 "cal_rx_core1"); 880 phy->base = devm_ioremap_resource(cal->dev, phy->res); 881 if (IS_ERR(phy->base)) { 882 cal_err(cal, "failed to ioremap\n"); 883 ret = PTR_ERR(phy->base); 884 goto error; 885 } 886 887 cal_dbg(1, cal, "ioresource %s at %pa - %pa\n", 888 phy->res->name, &phy->res->start, &phy->res->end); 889 890 ret = cal_camerarx_regmap_init(cal, phy); 891 if (ret) 892 goto error; 893 894 ret = cal_camerarx_parse_dt(phy); 895 if (ret) 896 goto error; 897 898 /* Initialize the V4L2 subdev and media entity. */ 899 sd = &phy->subdev; 900 v4l2_subdev_init(sd, &cal_camerarx_subdev_ops); 901 sd->entity.function = MEDIA_ENT_F_VID_IF_BRIDGE; 902 sd->flags = V4L2_SUBDEV_FL_HAS_DEVNODE; 903 snprintf(sd->name, sizeof(sd->name), "CAMERARX%u", instance); 904 sd->dev = cal->dev; 905 906 phy->pads[CAL_CAMERARX_PAD_SINK].flags = MEDIA_PAD_FL_SINK; 907 for (i = CAL_CAMERARX_PAD_FIRST_SOURCE; i < CAL_CAMERARX_NUM_PADS; ++i) 908 phy->pads[i].flags = MEDIA_PAD_FL_SOURCE; 909 sd->entity.ops = &cal_camerarx_media_ops; 910 ret = media_entity_pads_init(&sd->entity, ARRAY_SIZE(phy->pads), 911 phy->pads); 912 if (ret) 913 goto error; 914 915 ret = cal_camerarx_sd_init_cfg(sd, NULL); 916 if (ret) 917 goto error; 918 919 ret = v4l2_device_register_subdev(&cal->v4l2_dev, sd); 920 if (ret) 921 goto error; 922 923 return phy; 924 925 error: 926 media_entity_cleanup(&phy->subdev.entity); 927 kfree(phy); 928 return ERR_PTR(ret); 929 } 930 931 void cal_camerarx_destroy(struct cal_camerarx *phy) 932 { 933 if (!phy) 934 return; 935 936 v4l2_device_unregister_subdev(&phy->subdev); 937 media_entity_cleanup(&phy->subdev.entity); 938 of_node_put(phy->source_ep_node); 939 of_node_put(phy->source_node); 940 mutex_destroy(&phy->mutex); 941 kfree(phy); 942 } 943