media: ti: cal: Implement get_frame_desc for camera-rx

CAL uses get_frame_desc to get the VC and DT for the incoming CSI-2
stream, but does it in a bit hacky way. Clean this up by implementing
.get_

media: ti: cal: Implement get_frame_desc for camera-rx

CAL uses get_frame_desc to get the VC and DT for the incoming CSI-2
stream, but does it in a bit hacky way. Clean this up by implementing
.get_frame_desc to camera-rx, and calling that from cal.c.

No functional change intended.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>

show more ...

media: ti: cal: Use subdev state

Change TI CAL driver to use subdev state. No functional changes
(intended).

This allows us to get rid of the 'formats' field, as the formats are
kept in the state,

media: ti: cal: Use subdev state

Change TI CAL driver to use subdev state. No functional changes
(intended).

This allows us to get rid of the 'formats' field, as the formats are
kept in the state, and also the 'mutex' as we already have state locking.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>

show more ...

media: ti: cal: Fix cal_camerarx_create() error handling

We don't do a proper job at freeing resources in cal_camerarx_create's
error paths.

Fix these, and also switch the phy allcation from kzallo

media: ti: cal: Fix cal_camerarx_create() error handling

We don't do a proper job at freeing resources in cal_camerarx_create's
error paths.

Fix these, and also switch the phy allcation from kzalloc to
devm_kzalloc to simplify the code further.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>

show more ...

media: ti: cal: Clean up mbus formats uses

Clean up the CAL drivers uses of mbus formats:

- Switch all YUV formats from 2X8 formats to 1X16, as those are what
should be used for CSI-2 bus.

- Dro

media: ti: cal: Clean up mbus formats uses

Clean up the CAL drivers uses of mbus formats:

- Switch all YUV formats from 2X8 formats to 1X16, as those are what
should be used for CSI-2 bus.

- Drop 24 and 32 bit formats, as the driver doesn't support them (see
cal_ctx_pix_proc_config()).

- Switch RGB565_2X8_LE to RGB565_1X16 (for the same reason as for the
YUV formats) and drop RGB565_2X8_BE as it cannot be supported with
CSI-2.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>

show more ...

media: ti: cal: use CSI-2 frame number for seq number

The userspace needs a way to match received metadata buffers to pixel
data buffers. The obvious way to do this is to use the CSI-2 frame
number,

media: ti: cal: use CSI-2 frame number for seq number

The userspace needs a way to match received metadata buffers to pixel
data buffers. The obvious way to do this is to use the CSI-2 frame
number, as both the metadata and the pixel data have the same frame
number as they come from the same frame.

However, we don't have means to convey the frame number to userspace. We
do have the 'sequence' field, which with a few tricks can be used for
this purpose.

To achieve this, track the frame number for each virtual channel and
increase the sequence for each virtual channel by frame-number -
previous-frame-number, also taking into account the eventual wrap of the
CSI-2 frame number. If the CSI-2 peripheral does not support frame
numbers, CAL increases the frame number register by one each frame.

This way we get a monotonically increasing sequence number which is
common to all streams using the same virtual channel.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

show more ...

media: ti: cal: rename sd_state to state

Rename 'sd_state' parameters to 'state'. There are no other states, so
there is no ambiguity.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com

media: ti: cal: rename sd_state to state

Rename 'sd_state' parameters to 'state'. There are no other states, so
there is no ambiguity.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

show more ...

media: mc-entity: Rename media_entity_remote_pad() to media_pad_remote_pad_first()

The media_entity_remote_pad() is misnamed, as it operates on a pad and
not an entity. Rename it to media_pad_remote

media: mc-entity: Rename media_entity_remote_pad() to media_pad_remote_pad_first()

The media_entity_remote_pad() is misnamed, as it operates on a pad and
not an entity. Rename it to media_pad_remote_pad_first() to clarify its
behaviour.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

show more ...

media: ti: drop unexpected word 'a' in comments

there is an unexpected word 'a' in the comments that need to be dropped

file - drivers/media/platform/ti/cal/cal-camerarx.c
line - 308

* DRA80xM TR

media: ti: drop unexpected word 'a' in comments

there is an unexpected word 'a' in the comments that need to be dropped

file - drivers/media/platform/ti/cal/cal-camerarx.c
line - 308

* DRA80xM TRMs have a a slightly simplified sequence.

changed to:

* DRA80xM TRMs have a slightly simplified sequence.

Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

show more ...

media: ti: cal: use frame desc to get vc and dt

Use get_frame_desc() to get the frame desc from the connected source,
and use the provided virtual channel and datatype instead of hardcoded
ones.

ge

media: ti: cal: use frame desc to get vc and dt

Use get_frame_desc() to get the frame desc from the connected source,
and use the provided virtual channel and datatype instead of hardcoded
ones.

get_frame_desc() can contain multiple streams, but as we don't support
multiple streams yet, we will just always use the first stream.

If the source doesn't support get_frame_desc(), fall back to the
previous method of always capturing virtual channel 0 and any datatype.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

show more ...

media: platform: re-structure TI drivers

The ti-vpe/ sub-directory does not only contain the VPE-specific things.
It also contains the CAL driver, which is a completely different
subsystem. This is

media: platform: re-structure TI drivers

The ti-vpe/ sub-directory does not only contain the VPE-specific things.
It also contains the CAL driver, which is a completely different
subsystem. This is also not a good place to add new drivers for other TI
platforms since they will all get mixed up.

Separate the VPE and CAL parts into different sub-directories and rename
the ti-vpe/ sub-directory to ti/. This is now the place where new TI
platform drivers can be added.

[mchehab: rebased to apple on the top of media/platform/Kconfig series]
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

show more ...