1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * Texas Instruments ADS7950 SPI ADC driver 4 * 5 * Copyright 2016 David Lechner <david@lechnology.com> 6 * 7 * Based on iio/ad7923.c: 8 * Copyright 2011 Analog Devices Inc 9 * Copyright 2012 CS Systemes d'Information 10 * 11 * And also on hwmon/ads79xx.c 12 * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/ 13 * Nishanth Menon 14 */ 15 16 #include <linux/acpi.h> 17 #include <linux/bitops.h> 18 #include <linux/device.h> 19 #include <linux/err.h> 20 #include <linux/gpio/driver.h> 21 #include <linux/interrupt.h> 22 #include <linux/kernel.h> 23 #include <linux/module.h> 24 #include <linux/regulator/consumer.h> 25 #include <linux/slab.h> 26 #include <linux/spi/spi.h> 27 28 #include <linux/iio/buffer.h> 29 #include <linux/iio/iio.h> 30 #include <linux/iio/sysfs.h> 31 #include <linux/iio/trigger_consumer.h> 32 #include <linux/iio/triggered_buffer.h> 33 34 /* 35 * In case of ACPI, we use the 5000 mV as default for the reference pin. 36 * Device tree users encode that via the vref-supply regulator. 37 */ 38 #define TI_ADS7950_VA_MV_ACPI_DEFAULT 5000 39 40 #define TI_ADS7950_CR_GPIO BIT(14) 41 #define TI_ADS7950_CR_MANUAL BIT(12) 42 #define TI_ADS7950_CR_WRITE BIT(11) 43 #define TI_ADS7950_CR_CHAN(ch) ((ch) << 7) 44 #define TI_ADS7950_CR_RANGE_5V BIT(6) 45 #define TI_ADS7950_CR_GPIO_DATA BIT(4) 46 47 #define TI_ADS7950_MAX_CHAN 16 48 #define TI_ADS7950_NUM_GPIOS 4 49 50 #define TI_ADS7950_TIMESTAMP_SIZE (sizeof(int64_t) / sizeof(__be16)) 51 52 /* val = value, dec = left shift, bits = number of bits of the mask */ 53 #define TI_ADS7950_EXTRACT(val, dec, bits) \ 54 (((val) >> (dec)) & ((1 << (bits)) - 1)) 55 56 #define TI_ADS7950_MAN_CMD(cmd) (TI_ADS7950_CR_MANUAL | (cmd)) 57 #define TI_ADS7950_GPIO_CMD(cmd) (TI_ADS7950_CR_GPIO | (cmd)) 58 59 /* Manual mode configuration */ 60 #define TI_ADS7950_MAN_CMD_SETTINGS(st) \ 61 (TI_ADS7950_MAN_CMD(TI_ADS7950_CR_WRITE | st->cmd_settings_bitmask)) 62 /* GPIO mode configuration */ 63 #define TI_ADS7950_GPIO_CMD_SETTINGS(st) \ 64 (TI_ADS7950_GPIO_CMD(st->gpio_cmd_settings_bitmask)) 65 66 struct ti_ads7950_state { 67 struct spi_device *spi; 68 struct spi_transfer ring_xfer; 69 struct spi_transfer scan_single_xfer[3]; 70 struct spi_message ring_msg; 71 struct spi_message scan_single_msg; 72 73 /* Lock to protect the spi xfer buffers */ 74 struct mutex slock; 75 struct gpio_chip chip; 76 77 struct regulator *reg; 78 unsigned int vref_mv; 79 80 /* 81 * Bitmask of lower 7 bits used for configuration 82 * These bits only can be written when TI_ADS7950_CR_WRITE 83 * is set, otherwise it retains its original state. 84 * [0-3] GPIO signal 85 * [4] Set following frame to return GPIO signal values 86 * [5] Powers down device 87 * [6] Sets Vref range1(2.5v) or range2(5v) 88 * 89 * Bits present on Manual/Auto1/Auto2 commands 90 */ 91 unsigned int cmd_settings_bitmask; 92 93 /* 94 * Bitmask of GPIO command 95 * [0-3] GPIO direction 96 * [4-6] Different GPIO alarm mode configurations 97 * [7] GPIO 2 as device range input 98 * [8] GPIO 3 as device power down input 99 * [9] Reset all registers 100 * [10-11] N/A 101 */ 102 unsigned int gpio_cmd_settings_bitmask; 103 104 /* 105 * DMA (thus cache coherency maintenance) requires the 106 * transfer buffers to live in their own cache lines. 107 */ 108 u16 rx_buf[TI_ADS7950_MAX_CHAN + 2 + TI_ADS7950_TIMESTAMP_SIZE] 109 ____cacheline_aligned; 110 u16 tx_buf[TI_ADS7950_MAX_CHAN + 2]; 111 u16 single_tx; 112 u16 single_rx; 113 114 }; 115 116 struct ti_ads7950_chip_info { 117 const struct iio_chan_spec *channels; 118 unsigned int num_channels; 119 }; 120 121 enum ti_ads7950_id { 122 TI_ADS7950, 123 TI_ADS7951, 124 TI_ADS7952, 125 TI_ADS7953, 126 TI_ADS7954, 127 TI_ADS7955, 128 TI_ADS7956, 129 TI_ADS7957, 130 TI_ADS7958, 131 TI_ADS7959, 132 TI_ADS7960, 133 TI_ADS7961, 134 }; 135 136 #define TI_ADS7950_V_CHAN(index, bits) \ 137 { \ 138 .type = IIO_VOLTAGE, \ 139 .indexed = 1, \ 140 .channel = index, \ 141 .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \ 142 .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \ 143 .address = index, \ 144 .datasheet_name = "CH##index", \ 145 .scan_index = index, \ 146 .scan_type = { \ 147 .sign = 'u', \ 148 .realbits = bits, \ 149 .storagebits = 16, \ 150 .shift = 12 - (bits), \ 151 .endianness = IIO_CPU, \ 152 }, \ 153 } 154 155 #define DECLARE_TI_ADS7950_4_CHANNELS(name, bits) \ 156 const struct iio_chan_spec name ## _channels[] = { \ 157 TI_ADS7950_V_CHAN(0, bits), \ 158 TI_ADS7950_V_CHAN(1, bits), \ 159 TI_ADS7950_V_CHAN(2, bits), \ 160 TI_ADS7950_V_CHAN(3, bits), \ 161 IIO_CHAN_SOFT_TIMESTAMP(4), \ 162 } 163 164 #define DECLARE_TI_ADS7950_8_CHANNELS(name, bits) \ 165 const struct iio_chan_spec name ## _channels[] = { \ 166 TI_ADS7950_V_CHAN(0, bits), \ 167 TI_ADS7950_V_CHAN(1, bits), \ 168 TI_ADS7950_V_CHAN(2, bits), \ 169 TI_ADS7950_V_CHAN(3, bits), \ 170 TI_ADS7950_V_CHAN(4, bits), \ 171 TI_ADS7950_V_CHAN(5, bits), \ 172 TI_ADS7950_V_CHAN(6, bits), \ 173 TI_ADS7950_V_CHAN(7, bits), \ 174 IIO_CHAN_SOFT_TIMESTAMP(8), \ 175 } 176 177 #define DECLARE_TI_ADS7950_12_CHANNELS(name, bits) \ 178 const struct iio_chan_spec name ## _channels[] = { \ 179 TI_ADS7950_V_CHAN(0, bits), \ 180 TI_ADS7950_V_CHAN(1, bits), \ 181 TI_ADS7950_V_CHAN(2, bits), \ 182 TI_ADS7950_V_CHAN(3, bits), \ 183 TI_ADS7950_V_CHAN(4, bits), \ 184 TI_ADS7950_V_CHAN(5, bits), \ 185 TI_ADS7950_V_CHAN(6, bits), \ 186 TI_ADS7950_V_CHAN(7, bits), \ 187 TI_ADS7950_V_CHAN(8, bits), \ 188 TI_ADS7950_V_CHAN(9, bits), \ 189 TI_ADS7950_V_CHAN(10, bits), \ 190 TI_ADS7950_V_CHAN(11, bits), \ 191 IIO_CHAN_SOFT_TIMESTAMP(12), \ 192 } 193 194 #define DECLARE_TI_ADS7950_16_CHANNELS(name, bits) \ 195 const struct iio_chan_spec name ## _channels[] = { \ 196 TI_ADS7950_V_CHAN(0, bits), \ 197 TI_ADS7950_V_CHAN(1, bits), \ 198 TI_ADS7950_V_CHAN(2, bits), \ 199 TI_ADS7950_V_CHAN(3, bits), \ 200 TI_ADS7950_V_CHAN(4, bits), \ 201 TI_ADS7950_V_CHAN(5, bits), \ 202 TI_ADS7950_V_CHAN(6, bits), \ 203 TI_ADS7950_V_CHAN(7, bits), \ 204 TI_ADS7950_V_CHAN(8, bits), \ 205 TI_ADS7950_V_CHAN(9, bits), \ 206 TI_ADS7950_V_CHAN(10, bits), \ 207 TI_ADS7950_V_CHAN(11, bits), \ 208 TI_ADS7950_V_CHAN(12, bits), \ 209 TI_ADS7950_V_CHAN(13, bits), \ 210 TI_ADS7950_V_CHAN(14, bits), \ 211 TI_ADS7950_V_CHAN(15, bits), \ 212 IIO_CHAN_SOFT_TIMESTAMP(16), \ 213 } 214 215 static DECLARE_TI_ADS7950_4_CHANNELS(ti_ads7950, 12); 216 static DECLARE_TI_ADS7950_8_CHANNELS(ti_ads7951, 12); 217 static DECLARE_TI_ADS7950_12_CHANNELS(ti_ads7952, 12); 218 static DECLARE_TI_ADS7950_16_CHANNELS(ti_ads7953, 12); 219 static DECLARE_TI_ADS7950_4_CHANNELS(ti_ads7954, 10); 220 static DECLARE_TI_ADS7950_8_CHANNELS(ti_ads7955, 10); 221 static DECLARE_TI_ADS7950_12_CHANNELS(ti_ads7956, 10); 222 static DECLARE_TI_ADS7950_16_CHANNELS(ti_ads7957, 10); 223 static DECLARE_TI_ADS7950_4_CHANNELS(ti_ads7958, 8); 224 static DECLARE_TI_ADS7950_8_CHANNELS(ti_ads7959, 8); 225 static DECLARE_TI_ADS7950_12_CHANNELS(ti_ads7960, 8); 226 static DECLARE_TI_ADS7950_16_CHANNELS(ti_ads7961, 8); 227 228 static const struct ti_ads7950_chip_info ti_ads7950_chip_info[] = { 229 [TI_ADS7950] = { 230 .channels = ti_ads7950_channels, 231 .num_channels = ARRAY_SIZE(ti_ads7950_channels), 232 }, 233 [TI_ADS7951] = { 234 .channels = ti_ads7951_channels, 235 .num_channels = ARRAY_SIZE(ti_ads7951_channels), 236 }, 237 [TI_ADS7952] = { 238 .channels = ti_ads7952_channels, 239 .num_channels = ARRAY_SIZE(ti_ads7952_channels), 240 }, 241 [TI_ADS7953] = { 242 .channels = ti_ads7953_channels, 243 .num_channels = ARRAY_SIZE(ti_ads7953_channels), 244 }, 245 [TI_ADS7954] = { 246 .channels = ti_ads7954_channels, 247 .num_channels = ARRAY_SIZE(ti_ads7954_channels), 248 }, 249 [TI_ADS7955] = { 250 .channels = ti_ads7955_channels, 251 .num_channels = ARRAY_SIZE(ti_ads7955_channels), 252 }, 253 [TI_ADS7956] = { 254 .channels = ti_ads7956_channels, 255 .num_channels = ARRAY_SIZE(ti_ads7956_channels), 256 }, 257 [TI_ADS7957] = { 258 .channels = ti_ads7957_channels, 259 .num_channels = ARRAY_SIZE(ti_ads7957_channels), 260 }, 261 [TI_ADS7958] = { 262 .channels = ti_ads7958_channels, 263 .num_channels = ARRAY_SIZE(ti_ads7958_channels), 264 }, 265 [TI_ADS7959] = { 266 .channels = ti_ads7959_channels, 267 .num_channels = ARRAY_SIZE(ti_ads7959_channels), 268 }, 269 [TI_ADS7960] = { 270 .channels = ti_ads7960_channels, 271 .num_channels = ARRAY_SIZE(ti_ads7960_channels), 272 }, 273 [TI_ADS7961] = { 274 .channels = ti_ads7961_channels, 275 .num_channels = ARRAY_SIZE(ti_ads7961_channels), 276 }, 277 }; 278 279 /* 280 * ti_ads7950_update_scan_mode() setup the spi transfer buffer for the new 281 * scan mask 282 */ 283 static int ti_ads7950_update_scan_mode(struct iio_dev *indio_dev, 284 const unsigned long *active_scan_mask) 285 { 286 struct ti_ads7950_state *st = iio_priv(indio_dev); 287 int i, cmd, len; 288 289 len = 0; 290 for_each_set_bit(i, active_scan_mask, indio_dev->num_channels) { 291 cmd = TI_ADS7950_MAN_CMD(TI_ADS7950_CR_CHAN(i)); 292 st->tx_buf[len++] = cmd; 293 } 294 295 /* Data for the 1st channel is not returned until the 3rd transfer */ 296 st->tx_buf[len++] = 0; 297 st->tx_buf[len++] = 0; 298 299 st->ring_xfer.len = len * 2; 300 301 return 0; 302 } 303 304 static irqreturn_t ti_ads7950_trigger_handler(int irq, void *p) 305 { 306 struct iio_poll_func *pf = p; 307 struct iio_dev *indio_dev = pf->indio_dev; 308 struct ti_ads7950_state *st = iio_priv(indio_dev); 309 int ret; 310 311 mutex_lock(&st->slock); 312 ret = spi_sync(st->spi, &st->ring_msg); 313 if (ret < 0) 314 goto out; 315 316 iio_push_to_buffers_with_timestamp(indio_dev, &st->rx_buf[2], 317 iio_get_time_ns(indio_dev)); 318 319 out: 320 mutex_unlock(&st->slock); 321 iio_trigger_notify_done(indio_dev->trig); 322 323 return IRQ_HANDLED; 324 } 325 326 static int ti_ads7950_scan_direct(struct iio_dev *indio_dev, unsigned int ch) 327 { 328 struct ti_ads7950_state *st = iio_priv(indio_dev); 329 int ret, cmd; 330 331 mutex_lock(&st->slock); 332 cmd = TI_ADS7950_MAN_CMD(TI_ADS7950_CR_CHAN(ch)); 333 st->single_tx = cmd; 334 335 ret = spi_sync(st->spi, &st->scan_single_msg); 336 if (ret) 337 goto out; 338 339 ret = st->single_rx; 340 341 out: 342 mutex_unlock(&st->slock); 343 344 return ret; 345 } 346 347 static int ti_ads7950_get_range(struct ti_ads7950_state *st) 348 { 349 int vref; 350 351 if (st->vref_mv) { 352 vref = st->vref_mv; 353 } else { 354 vref = regulator_get_voltage(st->reg); 355 if (vref < 0) 356 return vref; 357 358 vref /= 1000; 359 } 360 361 if (st->cmd_settings_bitmask & TI_ADS7950_CR_RANGE_5V) 362 vref *= 2; 363 364 return vref; 365 } 366 367 static int ti_ads7950_read_raw(struct iio_dev *indio_dev, 368 struct iio_chan_spec const *chan, 369 int *val, int *val2, long m) 370 { 371 struct ti_ads7950_state *st = iio_priv(indio_dev); 372 int ret; 373 374 switch (m) { 375 case IIO_CHAN_INFO_RAW: 376 ret = ti_ads7950_scan_direct(indio_dev, chan->address); 377 if (ret < 0) 378 return ret; 379 380 if (chan->address != TI_ADS7950_EXTRACT(ret, 12, 4)) 381 return -EIO; 382 383 *val = TI_ADS7950_EXTRACT(ret, chan->scan_type.shift, 384 chan->scan_type.realbits); 385 386 return IIO_VAL_INT; 387 case IIO_CHAN_INFO_SCALE: 388 ret = ti_ads7950_get_range(st); 389 if (ret < 0) 390 return ret; 391 392 *val = ret; 393 *val2 = (1 << chan->scan_type.realbits) - 1; 394 395 return IIO_VAL_FRACTIONAL; 396 } 397 398 return -EINVAL; 399 } 400 401 static const struct iio_info ti_ads7950_info = { 402 .read_raw = &ti_ads7950_read_raw, 403 .update_scan_mode = ti_ads7950_update_scan_mode, 404 }; 405 406 static void ti_ads7950_set(struct gpio_chip *chip, unsigned int offset, 407 int value) 408 { 409 struct ti_ads7950_state *st = gpiochip_get_data(chip); 410 411 mutex_lock(&st->slock); 412 413 if (value) 414 st->cmd_settings_bitmask |= BIT(offset); 415 else 416 st->cmd_settings_bitmask &= ~BIT(offset); 417 418 st->single_tx = TI_ADS7950_MAN_CMD_SETTINGS(st); 419 spi_sync(st->spi, &st->scan_single_msg); 420 421 mutex_unlock(&st->slock); 422 } 423 424 static int ti_ads7950_get(struct gpio_chip *chip, unsigned int offset) 425 { 426 struct ti_ads7950_state *st = gpiochip_get_data(chip); 427 int ret; 428 429 mutex_lock(&st->slock); 430 431 /* If set as output, return the output */ 432 if (st->gpio_cmd_settings_bitmask & BIT(offset)) { 433 ret = st->cmd_settings_bitmask & BIT(offset); 434 goto out; 435 } 436 437 /* GPIO data bit sets SDO bits 12-15 to GPIO input */ 438 st->cmd_settings_bitmask |= TI_ADS7950_CR_GPIO_DATA; 439 st->single_tx = TI_ADS7950_MAN_CMD_SETTINGS(st); 440 ret = spi_sync(st->spi, &st->scan_single_msg); 441 if (ret) 442 goto out; 443 444 ret = ((st->single_rx >> 12) & BIT(offset)) ? 1 : 0; 445 446 /* Revert back to original settings */ 447 st->cmd_settings_bitmask &= ~TI_ADS7950_CR_GPIO_DATA; 448 st->single_tx = TI_ADS7950_MAN_CMD_SETTINGS(st); 449 ret = spi_sync(st->spi, &st->scan_single_msg); 450 if (ret) 451 goto out; 452 453 out: 454 mutex_unlock(&st->slock); 455 456 return ret; 457 } 458 459 static int ti_ads7950_get_direction(struct gpio_chip *chip, 460 unsigned int offset) 461 { 462 struct ti_ads7950_state *st = gpiochip_get_data(chip); 463 464 /* Bitmask is inverted from GPIO framework 0=input/1=output */ 465 return !(st->gpio_cmd_settings_bitmask & BIT(offset)); 466 } 467 468 static int _ti_ads7950_set_direction(struct gpio_chip *chip, int offset, 469 int input) 470 { 471 struct ti_ads7950_state *st = gpiochip_get_data(chip); 472 int ret = 0; 473 474 mutex_lock(&st->slock); 475 476 /* Only change direction if needed */ 477 if (input && (st->gpio_cmd_settings_bitmask & BIT(offset))) 478 st->gpio_cmd_settings_bitmask &= ~BIT(offset); 479 else if (!input && !(st->gpio_cmd_settings_bitmask & BIT(offset))) 480 st->gpio_cmd_settings_bitmask |= BIT(offset); 481 else 482 goto out; 483 484 st->single_tx = TI_ADS7950_GPIO_CMD_SETTINGS(st); 485 ret = spi_sync(st->spi, &st->scan_single_msg); 486 487 out: 488 mutex_unlock(&st->slock); 489 490 return ret; 491 } 492 493 static int ti_ads7950_direction_input(struct gpio_chip *chip, 494 unsigned int offset) 495 { 496 return _ti_ads7950_set_direction(chip, offset, 1); 497 } 498 499 static int ti_ads7950_direction_output(struct gpio_chip *chip, 500 unsigned int offset, int value) 501 { 502 ti_ads7950_set(chip, offset, value); 503 504 return _ti_ads7950_set_direction(chip, offset, 0); 505 } 506 507 static int ti_ads7950_init_hw(struct ti_ads7950_state *st) 508 { 509 int ret = 0; 510 511 mutex_lock(&st->slock); 512 513 /* Settings for Manual/Auto1/Auto2 commands */ 514 /* Default to 5v ref */ 515 st->cmd_settings_bitmask = TI_ADS7950_CR_RANGE_5V; 516 st->single_tx = TI_ADS7950_MAN_CMD_SETTINGS(st); 517 ret = spi_sync(st->spi, &st->scan_single_msg); 518 if (ret) 519 goto out; 520 521 /* Settings for GPIO command */ 522 st->gpio_cmd_settings_bitmask = 0x0; 523 st->single_tx = TI_ADS7950_GPIO_CMD_SETTINGS(st); 524 ret = spi_sync(st->spi, &st->scan_single_msg); 525 526 out: 527 mutex_unlock(&st->slock); 528 529 return ret; 530 } 531 532 static int ti_ads7950_probe(struct spi_device *spi) 533 { 534 struct ti_ads7950_state *st; 535 struct iio_dev *indio_dev; 536 const struct ti_ads7950_chip_info *info; 537 int ret; 538 539 spi->bits_per_word = 16; 540 spi->mode |= SPI_CS_WORD; 541 ret = spi_setup(spi); 542 if (ret < 0) { 543 dev_err(&spi->dev, "Error in spi setup\n"); 544 return ret; 545 } 546 547 indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*st)); 548 if (!indio_dev) 549 return -ENOMEM; 550 551 st = iio_priv(indio_dev); 552 553 spi_set_drvdata(spi, indio_dev); 554 555 st->spi = spi; 556 557 info = &ti_ads7950_chip_info[spi_get_device_id(spi)->driver_data]; 558 559 indio_dev->name = spi_get_device_id(spi)->name; 560 indio_dev->modes = INDIO_DIRECT_MODE; 561 indio_dev->channels = info->channels; 562 indio_dev->num_channels = info->num_channels; 563 indio_dev->info = &ti_ads7950_info; 564 565 /* build spi ring message */ 566 spi_message_init(&st->ring_msg); 567 568 st->ring_xfer.tx_buf = &st->tx_buf[0]; 569 st->ring_xfer.rx_buf = &st->rx_buf[0]; 570 /* len will be set later */ 571 st->ring_xfer.cs_change = true; 572 573 spi_message_add_tail(&st->ring_xfer, &st->ring_msg); 574 575 /* 576 * Setup default message. The sample is read at the end of the first 577 * transfer, then it takes one full cycle to convert the sample and one 578 * more cycle to send the value. The conversion process is driven by 579 * the SPI clock, which is why we have 3 transfers. The middle one is 580 * just dummy data sent while the chip is converting the sample that 581 * was read at the end of the first transfer. 582 */ 583 584 st->scan_single_xfer[0].tx_buf = &st->single_tx; 585 st->scan_single_xfer[0].len = 2; 586 st->scan_single_xfer[0].cs_change = 1; 587 st->scan_single_xfer[1].tx_buf = &st->single_tx; 588 st->scan_single_xfer[1].len = 2; 589 st->scan_single_xfer[1].cs_change = 1; 590 st->scan_single_xfer[2].rx_buf = &st->single_rx; 591 st->scan_single_xfer[2].len = 2; 592 593 spi_message_init_with_transfers(&st->scan_single_msg, 594 st->scan_single_xfer, 3); 595 596 /* Use hard coded value for reference voltage in ACPI case */ 597 if (ACPI_COMPANION(&spi->dev)) 598 st->vref_mv = TI_ADS7950_VA_MV_ACPI_DEFAULT; 599 600 mutex_init(&st->slock); 601 602 st->reg = devm_regulator_get(&spi->dev, "vref"); 603 if (IS_ERR(st->reg)) { 604 dev_err(&spi->dev, "Failed to get regulator \"vref\"\n"); 605 ret = PTR_ERR(st->reg); 606 goto error_destroy_mutex; 607 } 608 609 ret = regulator_enable(st->reg); 610 if (ret) { 611 dev_err(&spi->dev, "Failed to enable regulator \"vref\"\n"); 612 goto error_destroy_mutex; 613 } 614 615 ret = iio_triggered_buffer_setup(indio_dev, NULL, 616 &ti_ads7950_trigger_handler, NULL); 617 if (ret) { 618 dev_err(&spi->dev, "Failed to setup triggered buffer\n"); 619 goto error_disable_reg; 620 } 621 622 ret = ti_ads7950_init_hw(st); 623 if (ret) { 624 dev_err(&spi->dev, "Failed to init adc chip\n"); 625 goto error_cleanup_ring; 626 } 627 628 ret = iio_device_register(indio_dev); 629 if (ret) { 630 dev_err(&spi->dev, "Failed to register iio device\n"); 631 goto error_cleanup_ring; 632 } 633 634 /* Add GPIO chip */ 635 st->chip.label = dev_name(&st->spi->dev); 636 st->chip.parent = &st->spi->dev; 637 st->chip.owner = THIS_MODULE; 638 st->chip.base = -1; 639 st->chip.ngpio = TI_ADS7950_NUM_GPIOS; 640 st->chip.get_direction = ti_ads7950_get_direction; 641 st->chip.direction_input = ti_ads7950_direction_input; 642 st->chip.direction_output = ti_ads7950_direction_output; 643 st->chip.get = ti_ads7950_get; 644 st->chip.set = ti_ads7950_set; 645 646 ret = gpiochip_add_data(&st->chip, st); 647 if (ret) { 648 dev_err(&spi->dev, "Failed to init GPIOs\n"); 649 goto error_iio_device; 650 } 651 652 return 0; 653 654 error_iio_device: 655 iio_device_unregister(indio_dev); 656 error_cleanup_ring: 657 iio_triggered_buffer_cleanup(indio_dev); 658 error_disable_reg: 659 regulator_disable(st->reg); 660 error_destroy_mutex: 661 mutex_destroy(&st->slock); 662 663 return ret; 664 } 665 666 static int ti_ads7950_remove(struct spi_device *spi) 667 { 668 struct iio_dev *indio_dev = spi_get_drvdata(spi); 669 struct ti_ads7950_state *st = iio_priv(indio_dev); 670 671 gpiochip_remove(&st->chip); 672 iio_device_unregister(indio_dev); 673 iio_triggered_buffer_cleanup(indio_dev); 674 regulator_disable(st->reg); 675 mutex_destroy(&st->slock); 676 677 return 0; 678 } 679 680 static const struct spi_device_id ti_ads7950_id[] = { 681 { "ads7950", TI_ADS7950 }, 682 { "ads7951", TI_ADS7951 }, 683 { "ads7952", TI_ADS7952 }, 684 { "ads7953", TI_ADS7953 }, 685 { "ads7954", TI_ADS7954 }, 686 { "ads7955", TI_ADS7955 }, 687 { "ads7956", TI_ADS7956 }, 688 { "ads7957", TI_ADS7957 }, 689 { "ads7958", TI_ADS7958 }, 690 { "ads7959", TI_ADS7959 }, 691 { "ads7960", TI_ADS7960 }, 692 { "ads7961", TI_ADS7961 }, 693 { } 694 }; 695 MODULE_DEVICE_TABLE(spi, ti_ads7950_id); 696 697 static const struct of_device_id ads7950_of_table[] = { 698 { .compatible = "ti,ads7950", .data = &ti_ads7950_chip_info[TI_ADS7950] }, 699 { .compatible = "ti,ads7951", .data = &ti_ads7950_chip_info[TI_ADS7951] }, 700 { .compatible = "ti,ads7952", .data = &ti_ads7950_chip_info[TI_ADS7952] }, 701 { .compatible = "ti,ads7953", .data = &ti_ads7950_chip_info[TI_ADS7953] }, 702 { .compatible = "ti,ads7954", .data = &ti_ads7950_chip_info[TI_ADS7954] }, 703 { .compatible = "ti,ads7955", .data = &ti_ads7950_chip_info[TI_ADS7955] }, 704 { .compatible = "ti,ads7956", .data = &ti_ads7950_chip_info[TI_ADS7956] }, 705 { .compatible = "ti,ads7957", .data = &ti_ads7950_chip_info[TI_ADS7957] }, 706 { .compatible = "ti,ads7958", .data = &ti_ads7950_chip_info[TI_ADS7958] }, 707 { .compatible = "ti,ads7959", .data = &ti_ads7950_chip_info[TI_ADS7959] }, 708 { .compatible = "ti,ads7960", .data = &ti_ads7950_chip_info[TI_ADS7960] }, 709 { .compatible = "ti,ads7961", .data = &ti_ads7950_chip_info[TI_ADS7961] }, 710 { }, 711 }; 712 MODULE_DEVICE_TABLE(of, ads7950_of_table); 713 714 static struct spi_driver ti_ads7950_driver = { 715 .driver = { 716 .name = "ads7950", 717 .of_match_table = ads7950_of_table, 718 }, 719 .probe = ti_ads7950_probe, 720 .remove = ti_ads7950_remove, 721 .id_table = ti_ads7950_id, 722 }; 723 module_spi_driver(ti_ads7950_driver); 724 725 MODULE_AUTHOR("David Lechner <david@lechnology.com>"); 726 MODULE_DESCRIPTION("TI TI_ADS7950 ADC"); 727 MODULE_LICENSE("GPL v2"); 728