iio: adc: ti-ads7950: Set `can_sleep` flag for GPIO chip

The ads7950 uses a mutex as well as SPI transfers in its GPIO callbacks.
This means these callbacks can sleep and the `can_sleep` flag should

iio: adc: ti-ads7950: Set `can_sleep` flag for GPIO chip

The ads7950 uses a mutex as well as SPI transfers in its GPIO callbacks.
This means these callbacks can sleep and the `can_sleep` flag should be
set.

Having the flag set will make sure that warnings are generated when calling
any of the callbacks from a potentially non-sleeping context.

Fixes: c97dce792dc8 ("iio: adc: ti-ads7950: add GPIO support")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: David Lechner <david@lechnology.com>
Link: https://lore.kernel.org/r/20230312210933.2275376-1-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...

iio: adc: ti-ads7950: Fix alignment for DMA safety

____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_

iio: adc: ti-ads7950: Fix alignment for DMA safety

____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_DMA_MINALIGN definition.

Update the comment to include 'may'.

Fixes: 902c4b2446d4 ("iio: adc: New driver for TI ADS7950 chips")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: David Lechner <david@lechnology.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-37-jic23@kernel.org

show more ...

spi: make remove callback a void function

The value returned by an spi driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignore

spi: make remove callback a void function

The value returned by an spi driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)

So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Claudius Heine <ch@denx.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Acked-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220123175201.34839-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>

show more ...

iio: adc: ti-ads7950: Make use of the helper function dev_err_probe()

When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged

iio: adc: ti-ads7950: Make use of the helper function dev_err_probe()

When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
Using dev_err_probe() can reduce code size, and the error value
gets printed.

Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20211008092858.495-9-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...

iio: adc: ti-ads7950: Ensure CS is deasserted after reading channels

The ADS7950 requires that CS is deasserted after each SPI word. Before
commit e2540da86ef8 ("iio: adc: ti-ads7950: use SPI_CS_WOR

iio: adc: ti-ads7950: Ensure CS is deasserted after reading channels

The ADS7950 requires that CS is deasserted after each SPI word. Before
commit e2540da86ef8 ("iio: adc: ti-ads7950: use SPI_CS_WORD to reduce
CPU usage") the driver used a message with one spi transfer per channel
where each but the last one had .cs_change set to enforce a CS toggle.
This was wrongly translated into a message with a single transfer and
.cs_change set which results in a CS toggle after each word but the
last which corrupts the first adc conversion of all readouts after the
first readout.

Fixes: e2540da86ef8 ("iio: adc: ti-ads7950: use SPI_CS_WORD to reduce CPU usage")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: David Lechner <david@lechnology.com>
Tested-by: David Lechner <david@lechnology.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210709101110.1814294-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...

iio: adc: ti-ads7950: Ensure CS is deasserted after reading channels

commit 9898cb24e454602beb6e17bacf9f97b26c85c955 upstream.

The ADS7950 requires that CS is deasserted after each SPI word. Before

iio: adc: ti-ads7950: Ensure CS is deasserted after reading channels

commit 9898cb24e454602beb6e17bacf9f97b26c85c955 upstream.

The ADS7950 requires that CS is deasserted after each SPI word. Before
commit e2540da86ef8 ("iio: adc: ti-ads7950: use SPI_CS_WORD to reduce
CPU usage") the driver used a message with one spi transfer per channel
where each but the last one had .cs_change set to enforce a CS toggle.
This was wrongly translated into a message with a single transfer and
.cs_change set which results in a CS toggle after each word but the
last which corrupts the first adc conversion of all readouts after the
first readout.

Fixes: e2540da86ef8 ("iio: adc: ti-ads7950: use SPI_CS_WORD to reduce CPU usage")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: David Lechner <david@lechnology.com>
Tested-by: David Lechner <david@lechnology.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210709101110.1814294-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

Replace HTTP links with HTTPS ones: drivers/iio

Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.

Deterministic algorithm:
F

Replace HTTP links with HTTPS ones: drivers/iio

Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.

Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.

Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...

iio: remove explicit IIO device parent assignment

This patch applies the semantic patch:
@@
expression I, P, SP;
@@
I = devm_iio_device_alloc(P, SP);
...
- I->dev.parent = P;

It updates 302

iio: remove explicit IIO device parent assignment

This patch applies the semantic patch:
@@
expression I, P, SP;
@@
I = devm_iio_device_alloc(P, SP);
...
- I->dev.parent = P;

It updates 302 files and does 307 deletions.
This semantic patch also removes some comments like
'/* Establish that the iio_dev is a child of the i2c device */'

But this is is only done in case where the block is left empty.

The patch does not seem to cover all cases. It looks like in some cases a
different variable is used in some cases to assign the parent, but it
points to the same reference.
In other cases, the block covered by ... may be just too big to be covered
by the semantic patch.

However, this looks pretty good as well, as it does cover a big bulk of the
drivers that should remove the parent assignment.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...

iio: adc: ti-ads7950: Fix a typo in an error message

Fix a typo:
s/get get/to get/

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cam

iio: adc: ti-ads7950: Fix a typo in an error message

Fix a typo:
s/get get/to get/

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...

iio: adc: ti-ads7950: add GPIO support

The ADS79XX has GPIO pins that can be used. Add support for the GPIO
pins using the GPIO chip framework.

Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Re

iio: adc: ti-ads7950: add GPIO support

The ADS79XX has GPIO pins that can be used. Add support for the GPIO
pins using the GPIO chip framework.

Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...

iio: adc: ti-ads7950: Fix improper use of mlock

Indio->mlock is used for protecting the different iio device modes.
It is currently not being used in this way. Replace the lock with
an internal lock

iio: adc: ti-ads7950: Fix improper use of mlock

Indio->mlock is used for protecting the different iio device modes.
It is currently not being used in this way. Replace the lock with
an internal lock specifically used for protecting the SPI transfer
buffer.

Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...

iio: adc: ti-ads7950: use SPI_CS_WORD to reduce CPU usage

This changes how the SPI message for the triggered buffer is setup in
the TI ADS7950 A/DC driver. By using the SPI_CS_WORD flag, we can read

iio: adc: ti-ads7950: use SPI_CS_WORD to reduce CPU usage

This changes how the SPI message for the triggered buffer is setup in
the TI ADS7950 A/DC driver. By using the SPI_CS_WORD flag, we can read
multiple samples in a single SPI transfer. If the SPI controller
supports DMA transfers, we can see a significant reduction in CPU usage.

For example, on an ARM9 system running at 456MHz reading just 4 channels
at 100Hz: before this change, top shows the CPU usage of the IRQ thread
of this driver to be ~7.7%. After this change, the CPU usage drops to
~3.8%.

The use of big-endian for the raw data was cargo culted from another
driver when this driver was originally written. It used an SPI word size
of 8 bits and big-endian byte ordering to effectively emulate 16 bit
words.

Now, in order to inject a CS toggle between each word, we need to use
the correct word size, otherwise we would get a CS toggle half way
through each word 16-bit. The SPI subsystem uses CPU byte ordering for
multi-byte words. So, the data we get back from the SPI is going to be
CPU endian now no matter what. Converting that to big endian will just
add overhead on little endian systems so we opt to change the raw data
format from big endian to CPU endian.

There is a small risk that this could break some lazy userspace programs
that use the raw data without checking the data format. We can address
this if/when it actually comes up.

Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...

iio: adc: ti-ads7950: allow simultaneous use of buffer and direct mode

This modifies the TI ADS7950 A/DC driver to allow the simultaneous use
of both the triggered buffer and reading channels direct

iio: adc: ti-ads7950: allow simultaneous use of buffer and direct mode

This modifies the TI ADS7950 A/DC driver to allow the simultaneous use
of both the triggered buffer and reading channels directly (via in-
kernel API or sysfs).

The use case for this is on LEGO MINDSTORMS EV3. Two of the voltage
channels are used in-kernel by a power supply driver, which reads the
values using iio_read_channel_processed(). These channels are only read
at a slow rate (<= 1Hz). However, we want to be able to read 12 other
channels at the same time using the triggered buffer at a high rate (>=
100Hz).

Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...

iio: adc: ti-ads7950: use SPDX-License-Identifier

This updates the ti-ads7950.c file to use SPDX-License-Identifier
instead of more verbose license text.

Signed-off-by: David Lechner <david@lechnol

iio: adc: ti-ads7950: use SPDX-License-Identifier

This updates the ti-ads7950.c file to use SPDX-License-Identifier
instead of more verbose license text.

Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...

iio:adc: drop assign iio_info.driver_module and iio_trigger_ops.owner

The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
el

iio:adc: drop assign iio_info.driver_module and iio_trigger_ops.owner

The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.

Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>

show more ...

iio: adc: ti-ads7950: Allow to use on ACPI platforms

ACPI enabled platforms do not have a mean of regulators. Instead we use
hard coded voltage value for reference pin. When value is 0 (default) we

iio: adc: ti-ads7950: Allow to use on ACPI platforms

ACPI enabled platforms do not have a mean of regulators. Instead we use
hard coded voltage value for reference pin. When value is 0 (default) we
fall back to request a regulator.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...

iio: adc: ti-ads7950: Add OF device ID table

The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
SPI d

iio: adc: ti-ads7950: Add OF device ID table

The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
SPI device registered via OF will always match a legacy SPI device ID and
that the MODALIAS reported will always be of the form spi:<device>.

There is an ACPI method to enumerate such devices via specific ACPI ID
and use of compatible strings. It will not work for the drivers which
have no OF match ID table present.

Besides this could change in the future so the correct approach is to
have an OF device ID table if the devices are registered via OF.

Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...

iio: adc: ti-ads7950: Change regulator matching string to "vref"

This changes the reference voltage regulator matching string from "refin"
to "vref". This is to be consistent with other A/DC chips t

iio: adc: ti-ads7950: Change regulator matching string to "vref"

This changes the reference voltage regulator matching string from "refin"
to "vref". This is to be consistent with other A/DC chips that also use
"vref-supply" in their device tree bindings.

Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

show more ...

iio: adc: ti-ads7950: Drop "ti-" prefix from module name

This drops the "ti-" prefix from the module name. It makes the module name
consistent with other iio ti-ads* drivers and it makes the driver

iio: adc: ti-ads7950: Drop "ti-" prefix from module name

This drops the "ti-" prefix from the module name. It makes the module name
consistent with other iio ti-ads* drivers and it makes the driver work
with device tree (the spi subsystem drops the "ti," prefix when matching
compatible strings from device tree).

Tested working on LEGO MINDSTORMS EV3 with the following device tree node:

adc@3 {
compatible = "ti,ads7957";
reg = <3>;
#io-channel-cells = <1>;
spi-max-frequency = <10000000>;
vref-supply = <&adc_ref>;
};

Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

show more ...

iio: adc: New driver for TI ADS7950 chips

This adds a new driver for the TI ADS7950 family of ADC chips. These
communicate using SPI and come in 8/10/12-bit and 4/8/12/16 channel
varieties.

Signed-

iio: adc: New driver for TI ADS7950 chips

This adds a new driver for the TI ADS7950 family of ADC chips. These
communicate using SPI and come in 8/10/12-bit and 4/8/12/16 channel
varieties.

Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

show more ...

iio: adc: ti-ads7950: Ensure CS is deasserted after reading channels

commit 9898cb24e454602beb6e17bacf9f97b26c85c955 upstream.

The ADS7950 requires that CS is deasserted after each

iio: adc: ti-ads7950: Ensure CS is deasserted after reading channels

commit 9898cb24e454602beb6e17bacf9f97b26c85c955 upstream.

The ADS7950 requires that CS is deasserted after each SPI word. Before
commit e2540da86ef8 ("iio: adc: ti-ads7950: use SPI_CS_WORD to reduce
CPU usage") the driver used a message with one spi transfer per channel
where each but the last one had .cs_change set to enforce a CS toggle.
This was wrongly translated into a message with a single transfer and
.cs_change set which results in a CS toggle after each word but the
last which corrupts the first adc conversion of all readouts after the
first readout.

Fixes: e2540da86ef8 ("iio: adc: ti-ads7950: use SPI_CS_WORD to reduce CPU usage")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: David Lechner <david@lechnology.com>
Tested-by: David Lechner <david@lechnology.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210709101110.1814294-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

Replace HTTP links with HTTPS ones: drivers/iio

Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.

De

Replace HTTP links with HTTPS ones: drivers/iio

Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.

Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.

Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...

iio: remove explicit IIO device parent assignment

This patch applies the semantic patch:
@@
expression I, P, SP;
@@
I = devm_iio_device_alloc(P, SP);
...
- I->

iio: remove explicit IIO device parent assignment

This patch applies the semantic patch:
@@
expression I, P, SP;
@@
I = devm_iio_device_alloc(P, SP);
...
- I->dev.parent = P;

It updates 302 files and does 307 deletions.
This semantic patch also removes some comments like
'/* Establish that the iio_dev is a child of the i2c device */'

But this is is only done in case where the block is left empty.

The patch does not seem to cover all cases. It looks like in some cases a
different variable is used in some cases to assign the parent, but it
points to the same reference.
In other cases, the block covered by ... may be just too big to be covered
by the semantic patch.

However, this looks pretty good as well, as it does cover a big bulk of the
drivers that should remove the parent assignment.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...

iio: adc: ti-ads7950: Fix a typo in an error message

Fix a typo:
s/get get/to get/

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jonath

iio: adc: ti-ads7950: Fix a typo in an error message

Fix a typo:
s/get get/to get/

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...

iio: adc: ti-ads7950: add GPIO support

The ADS79XX has GPIO pins that can be used. Add support for the GPIO
pins using the GPIO chip framework.

Signed-off-by: Justin Chen <justi

iio: adc: ti-ads7950: add GPIO support

The ADS79XX has GPIO pins that can be used. Add support for the GPIO
pins using the GPIO chip framework.

Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...