1 // SPDX-License-Identifier: GPL-2.0
2 /*
3 * comedi/drivers/dt2801.c
4 * Device Driver for DataTranslation DT2801
5 *
6 */
7 /*
8 * Driver: dt2801
9 * Description: Data Translation DT2801 series and DT01-EZ
10 * Author: ds
11 * Status: works
12 * Devices: [Data Translation] DT2801 (dt2801), DT2801-A, DT2801/5716A,
13 * DT2805, DT2805/5716A, DT2808, DT2818, DT2809, DT01-EZ
14 *
15 * This driver can autoprobe the type of board.
16 *
17 * Configuration options:
18 * [0] - I/O port base address
19 * [1] - unused
20 * [2] - A/D reference 0=differential, 1=single-ended
21 * [3] - A/D range
22 * 0 = [-10, 10]
23 * 1 = [0,10]
24 * [4] - D/A 0 range
25 * 0 = [-10, 10]
26 * 1 = [-5,5]
27 * 2 = [-2.5,2.5]
28 * 3 = [0,10]
29 * 4 = [0,5]
30 * [5] - D/A 1 range (same choices)
31 */
32
33 #include <linux/module.h>
34 #include <linux/comedi/comedidev.h>
35 #include <linux/delay.h>
36
37 #define DT2801_TIMEOUT 1000
38
39 /* Hardware Configuration */
40 /* ====================== */
41
42 #define DT2801_MAX_DMA_SIZE (64 * 1024)
43
44 /* define's */
45 /* ====================== */
46
47 /* Commands */
48 #define DT_C_RESET 0x0
49 #define DT_C_CLEAR_ERR 0x1
50 #define DT_C_READ_ERRREG 0x2
51 #define DT_C_SET_CLOCK 0x3
52
53 #define DT_C_TEST 0xb
54 #define DT_C_STOP 0xf
55
56 #define DT_C_SET_DIGIN 0x4
57 #define DT_C_SET_DIGOUT 0x5
58 #define DT_C_READ_DIG 0x6
59 #define DT_C_WRITE_DIG 0x7
60
61 #define DT_C_WRITE_DAIM 0x8
62 #define DT_C_SET_DA 0x9
63 #define DT_C_WRITE_DA 0xa
64
65 #define DT_C_READ_ADIM 0xc
66 #define DT_C_SET_AD 0xd
67 #define DT_C_READ_AD 0xe
68
69 /*
70 * Command modifiers (only used with read/write), EXTTRIG can be
71 * used with some other commands.
72 */
73 #define DT_MOD_DMA BIT(4)
74 #define DT_MOD_CONT BIT(5)
75 #define DT_MOD_EXTCLK BIT(6)
76 #define DT_MOD_EXTTRIG BIT(7)
77
78 /* Bits in status register */
79 #define DT_S_DATA_OUT_READY BIT(0)
80 #define DT_S_DATA_IN_FULL BIT(1)
81 #define DT_S_READY BIT(2)
82 #define DT_S_COMMAND BIT(3)
83 #define DT_S_COMPOSITE_ERROR BIT(7)
84
85 /* registers */
86 #define DT2801_DATA 0
87 #define DT2801_STATUS 1
88 #define DT2801_CMD 1
89
90 #if 0
91 /* ignore 'defined but not used' warning */
92 static const struct comedi_lrange range_dt2801_ai_pgh_bipolar = {
93 4, {
94 BIP_RANGE(10),
95 BIP_RANGE(5),
96 BIP_RANGE(2.5),
97 BIP_RANGE(1.25)
98 }
99 };
100 #endif
101 static const struct comedi_lrange range_dt2801_ai_pgl_bipolar = {
102 4, {
103 BIP_RANGE(10),
104 BIP_RANGE(1),
105 BIP_RANGE(0.1),
106 BIP_RANGE(0.02)
107 }
108 };
109
110 #if 0
111 /* ignore 'defined but not used' warning */
112 static const struct comedi_lrange range_dt2801_ai_pgh_unipolar = {
113 4, {
114 UNI_RANGE(10),
115 UNI_RANGE(5),
116 UNI_RANGE(2.5),
117 UNI_RANGE(1.25)
118 }
119 };
120 #endif
121 static const struct comedi_lrange range_dt2801_ai_pgl_unipolar = {
122 4, {
123 UNI_RANGE(10),
124 UNI_RANGE(1),
125 UNI_RANGE(0.1),
126 UNI_RANGE(0.02)
127 }
128 };
129
130 struct dt2801_board {
131 const char *name;
132 int boardcode;
133 int ad_diff;
134 int ad_chan;
135 int adbits;
136 int adrangetype;
137 int dabits;
138 };
139
140 /*
141 * Typeid's for the different boards of the DT2801-series
142 * (taken from the test-software, that comes with the board)
143 */
144 static const struct dt2801_board boardtypes[] = {
145 {
146 .name = "dt2801",
147 .boardcode = 0x09,
148 .ad_diff = 2,
149 .ad_chan = 16,
150 .adbits = 12,
151 .adrangetype = 0,
152 .dabits = 12},
153 {
154 .name = "dt2801-a",
155 .boardcode = 0x52,
156 .ad_diff = 2,
157 .ad_chan = 16,
158 .adbits = 12,
159 .adrangetype = 0,
160 .dabits = 12},
161 {
162 .name = "dt2801/5716a",
163 .boardcode = 0x82,
164 .ad_diff = 1,
165 .ad_chan = 16,
166 .adbits = 16,
167 .adrangetype = 1,
168 .dabits = 12},
169 {
170 .name = "dt2805",
171 .boardcode = 0x12,
172 .ad_diff = 1,
173 .ad_chan = 16,
174 .adbits = 12,
175 .adrangetype = 0,
176 .dabits = 12},
177 {
178 .name = "dt2805/5716a",
179 .boardcode = 0x92,
180 .ad_diff = 1,
181 .ad_chan = 16,
182 .adbits = 16,
183 .adrangetype = 1,
184 .dabits = 12},
185 {
186 .name = "dt2808",
187 .boardcode = 0x20,
188 .ad_diff = 0,
189 .ad_chan = 16,
190 .adbits = 12,
191 .adrangetype = 2,
192 .dabits = 8},
193 {
194 .name = "dt2818",
195 .boardcode = 0xa2,
196 .ad_diff = 0,
197 .ad_chan = 4,
198 .adbits = 12,
199 .adrangetype = 0,
200 .dabits = 12},
201 {
202 .name = "dt2809",
203 .boardcode = 0xb0,
204 .ad_diff = 0,
205 .ad_chan = 8,
206 .adbits = 12,
207 .adrangetype = 1,
208 .dabits = 12},
209 };
210
211 struct dt2801_private {
212 const struct comedi_lrange *dac_range_types[2];
213 };
214
215 /*
216 * These are the low-level routines:
217 * writecommand: write a command to the board
218 * writedata: write data byte
219 * readdata: read data byte
220 */
221
222 /*
223 * Only checks DataOutReady-flag, not the Ready-flag as it is done
224 * in the examples of the manual. I don't see why this should be
225 * necessary.
226 */
dt2801_readdata(struct comedi_device * dev,int * data)227 static int dt2801_readdata(struct comedi_device *dev, int *data)
228 {
229 int stat = 0;
230 int timeout = DT2801_TIMEOUT;
231
232 do {
233 stat = inb_p(dev->iobase + DT2801_STATUS);
234 if (stat & (DT_S_COMPOSITE_ERROR | DT_S_READY))
235 return stat;
236 if (stat & DT_S_DATA_OUT_READY) {
237 *data = inb_p(dev->iobase + DT2801_DATA);
238 return 0;
239 }
240 } while (--timeout > 0);
241
242 return -ETIME;
243 }
244
dt2801_readdata2(struct comedi_device * dev,int * data)245 static int dt2801_readdata2(struct comedi_device *dev, int *data)
246 {
247 int lb = 0;
248 int hb = 0;
249 int ret;
250
251 ret = dt2801_readdata(dev, &lb);
252 if (ret)
253 return ret;
254 ret = dt2801_readdata(dev, &hb);
255 if (ret)
256 return ret;
257
258 *data = (hb << 8) + lb;
259 return 0;
260 }
261
dt2801_writedata(struct comedi_device * dev,unsigned int data)262 static int dt2801_writedata(struct comedi_device *dev, unsigned int data)
263 {
264 int stat = 0;
265 int timeout = DT2801_TIMEOUT;
266
267 do {
268 stat = inb_p(dev->iobase + DT2801_STATUS);
269
270 if (stat & DT_S_COMPOSITE_ERROR)
271 return stat;
272 if (!(stat & DT_S_DATA_IN_FULL)) {
273 outb_p(data & 0xff, dev->iobase + DT2801_DATA);
274 return 0;
275 }
276 } while (--timeout > 0);
277
278 return -ETIME;
279 }
280
dt2801_writedata2(struct comedi_device * dev,unsigned int data)281 static int dt2801_writedata2(struct comedi_device *dev, unsigned int data)
282 {
283 int ret;
284
285 ret = dt2801_writedata(dev, data & 0xff);
286 if (ret < 0)
287 return ret;
288 ret = dt2801_writedata(dev, data >> 8);
289 if (ret < 0)
290 return ret;
291
292 return 0;
293 }
294
dt2801_wait_for_ready(struct comedi_device * dev)295 static int dt2801_wait_for_ready(struct comedi_device *dev)
296 {
297 int timeout = DT2801_TIMEOUT;
298 int stat;
299
300 stat = inb_p(dev->iobase + DT2801_STATUS);
301 if (stat & DT_S_READY)
302 return 0;
303 do {
304 stat = inb_p(dev->iobase + DT2801_STATUS);
305
306 if (stat & DT_S_COMPOSITE_ERROR)
307 return stat;
308 if (stat & DT_S_READY)
309 return 0;
310 } while (--timeout > 0);
311
312 return -ETIME;
313 }
314
dt2801_writecmd(struct comedi_device * dev,int command)315 static void dt2801_writecmd(struct comedi_device *dev, int command)
316 {
317 int stat;
318
319 dt2801_wait_for_ready(dev);
320
321 stat = inb_p(dev->iobase + DT2801_STATUS);
322 if (stat & DT_S_COMPOSITE_ERROR) {
323 dev_dbg(dev->class_dev,
324 "composite-error in %s, ignoring\n", __func__);
325 }
326 if (!(stat & DT_S_READY))
327 dev_dbg(dev->class_dev, "!ready in %s, ignoring\n", __func__);
328 outb_p(command, dev->iobase + DT2801_CMD);
329 }
330
dt2801_reset(struct comedi_device * dev)331 static int dt2801_reset(struct comedi_device *dev)
332 {
333 int board_code = 0;
334 unsigned int stat;
335 int timeout;
336
337 /* pull random data from data port */
338 inb_p(dev->iobase + DT2801_DATA);
339 inb_p(dev->iobase + DT2801_DATA);
340 inb_p(dev->iobase + DT2801_DATA);
341 inb_p(dev->iobase + DT2801_DATA);
342
343 /* dt2801_writecmd(dev,DT_C_STOP); */
344 outb_p(DT_C_STOP, dev->iobase + DT2801_CMD);
345
346 /* dt2801_wait_for_ready(dev); */
347 usleep_range(100, 200);
348 timeout = 10000;
349 do {
350 stat = inb_p(dev->iobase + DT2801_STATUS);
351 if (stat & DT_S_READY)
352 break;
353 } while (timeout--);
354 if (!timeout)
355 dev_dbg(dev->class_dev, "timeout 1 status=0x%02x\n", stat);
356
357 /* dt2801_readdata(dev,&board_code); */
358
359 outb_p(DT_C_RESET, dev->iobase + DT2801_CMD);
360 /* dt2801_writecmd(dev,DT_C_RESET); */
361
362 usleep_range(100, 200);
363 timeout = 10000;
364 do {
365 stat = inb_p(dev->iobase + DT2801_STATUS);
366 if (stat & DT_S_READY)
367 break;
368 } while (timeout--);
369 if (!timeout)
370 dev_dbg(dev->class_dev, "timeout 2 status=0x%02x\n", stat);
371
372 dt2801_readdata(dev, &board_code);
373
374 return board_code;
375 }
376
probe_number_of_ai_chans(struct comedi_device * dev)377 static int probe_number_of_ai_chans(struct comedi_device *dev)
378 {
379 int n_chans;
380 int stat;
381 int data;
382
383 for (n_chans = 0; n_chans < 16; n_chans++) {
384 dt2801_writecmd(dev, DT_C_READ_ADIM);
385 dt2801_writedata(dev, 0);
386 dt2801_writedata(dev, n_chans);
387 stat = dt2801_readdata2(dev, &data);
388
389 if (stat)
390 break;
391 }
392
393 dt2801_reset(dev);
394 dt2801_reset(dev);
395
396 return n_chans;
397 }
398
399 static const struct comedi_lrange *dac_range_table[] = {
400 &range_bipolar10,
401 &range_bipolar5,
402 &range_bipolar2_5,
403 &range_unipolar10,
404 &range_unipolar5
405 };
406
dac_range_lkup(int opt)407 static const struct comedi_lrange *dac_range_lkup(int opt)
408 {
409 if (opt < 0 || opt >= 5)
410 return &range_unknown;
411 return dac_range_table[opt];
412 }
413
ai_range_lkup(int type,int opt)414 static const struct comedi_lrange *ai_range_lkup(int type, int opt)
415 {
416 switch (type) {
417 case 0:
418 return (opt) ?
419 &range_dt2801_ai_pgl_unipolar :
420 &range_dt2801_ai_pgl_bipolar;
421 case 1:
422 return (opt) ? &range_unipolar10 : &range_bipolar10;
423 case 2:
424 return &range_unipolar5;
425 }
426 return &range_unknown;
427 }
428
dt2801_error(struct comedi_device * dev,int stat)429 static int dt2801_error(struct comedi_device *dev, int stat)
430 {
431 if (stat < 0) {
432 if (stat == -ETIME)
433 dev_dbg(dev->class_dev, "timeout\n");
434 else
435 dev_dbg(dev->class_dev, "error %d\n", stat);
436 return stat;
437 }
438 dev_dbg(dev->class_dev, "error status 0x%02x, resetting...\n", stat);
439
440 dt2801_reset(dev);
441 dt2801_reset(dev);
442
443 return -EIO;
444 }
445
dt2801_ai_insn_read(struct comedi_device * dev,struct comedi_subdevice * s,struct comedi_insn * insn,unsigned int * data)446 static int dt2801_ai_insn_read(struct comedi_device *dev,
447 struct comedi_subdevice *s,
448 struct comedi_insn *insn, unsigned int *data)
449 {
450 int d;
451 int stat;
452 int i;
453
454 for (i = 0; i < insn->n; i++) {
455 dt2801_writecmd(dev, DT_C_READ_ADIM);
456 dt2801_writedata(dev, CR_RANGE(insn->chanspec));
457 dt2801_writedata(dev, CR_CHAN(insn->chanspec));
458 stat = dt2801_readdata2(dev, &d);
459
460 if (stat != 0)
461 return dt2801_error(dev, stat);
462
463 data[i] = d;
464 }
465
466 return i;
467 }
468
dt2801_ao_insn_write(struct comedi_device * dev,struct comedi_subdevice * s,struct comedi_insn * insn,unsigned int * data)469 static int dt2801_ao_insn_write(struct comedi_device *dev,
470 struct comedi_subdevice *s,
471 struct comedi_insn *insn,
472 unsigned int *data)
473 {
474 unsigned int chan = CR_CHAN(insn->chanspec);
475
476 dt2801_writecmd(dev, DT_C_WRITE_DAIM);
477 dt2801_writedata(dev, chan);
478 dt2801_writedata2(dev, data[0]);
479
480 s->readback[chan] = data[0];
481
482 return 1;
483 }
484
dt2801_dio_insn_bits(struct comedi_device * dev,struct comedi_subdevice * s,struct comedi_insn * insn,unsigned int * data)485 static int dt2801_dio_insn_bits(struct comedi_device *dev,
486 struct comedi_subdevice *s,
487 struct comedi_insn *insn,
488 unsigned int *data)
489 {
490 int which = (s == &dev->subdevices[3]) ? 1 : 0;
491 unsigned int val = 0;
492
493 if (comedi_dio_update_state(s, data)) {
494 dt2801_writecmd(dev, DT_C_WRITE_DIG);
495 dt2801_writedata(dev, which);
496 dt2801_writedata(dev, s->state);
497 }
498
499 dt2801_writecmd(dev, DT_C_READ_DIG);
500 dt2801_writedata(dev, which);
501 dt2801_readdata(dev, &val);
502
503 data[1] = val;
504
505 return insn->n;
506 }
507
dt2801_dio_insn_config(struct comedi_device * dev,struct comedi_subdevice * s,struct comedi_insn * insn,unsigned int * data)508 static int dt2801_dio_insn_config(struct comedi_device *dev,
509 struct comedi_subdevice *s,
510 struct comedi_insn *insn,
511 unsigned int *data)
512 {
513 int ret;
514
515 ret = comedi_dio_insn_config(dev, s, insn, data, 0xff);
516 if (ret)
517 return ret;
518
519 dt2801_writecmd(dev, s->io_bits ? DT_C_SET_DIGOUT : DT_C_SET_DIGIN);
520 dt2801_writedata(dev, (s == &dev->subdevices[3]) ? 1 : 0);
521
522 return insn->n;
523 }
524
525 /*
526 * options:
527 * [0] - i/o base
528 * [1] - unused
529 * [2] - a/d 0=differential, 1=single-ended
530 * [3] - a/d range 0=[-10,10], 1=[0,10]
531 * [4] - dac0 range 0=[-10,10], 1=[-5,5], 2=[-2.5,2.5] 3=[0,10], 4=[0,5]
532 * [5] - dac1 range 0=[-10,10], 1=[-5,5], 2=[-2.5,2.5] 3=[0,10], 4=[0,5]
533 */
dt2801_attach(struct comedi_device * dev,struct comedi_devconfig * it)534 static int dt2801_attach(struct comedi_device *dev, struct comedi_devconfig *it)
535 {
536 const struct dt2801_board *board;
537 struct dt2801_private *devpriv;
538 struct comedi_subdevice *s;
539 int board_code, type;
540 int ret = 0;
541 int n_ai_chans;
542
543 ret = comedi_request_region(dev, it->options[0], 0x2);
544 if (ret)
545 return ret;
546
547 /* do some checking */
548
549 board_code = dt2801_reset(dev);
550
551 /* heh. if it didn't work, try it again. */
552 if (!board_code)
553 board_code = dt2801_reset(dev);
554
555 for (type = 0; type < ARRAY_SIZE(boardtypes); type++) {
556 if (boardtypes[type].boardcode == board_code)
557 goto havetype;
558 }
559 dev_dbg(dev->class_dev,
560 "unrecognized board code=0x%02x, contact author\n", board_code);
561 type = 0;
562
563 havetype:
564 dev->board_ptr = boardtypes + type;
565 board = dev->board_ptr;
566
567 n_ai_chans = probe_number_of_ai_chans(dev);
568
569 ret = comedi_alloc_subdevices(dev, 4);
570 if (ret)
571 goto out;
572
573 devpriv = comedi_alloc_devpriv(dev, sizeof(*devpriv));
574 if (!devpriv)
575 return -ENOMEM;
576
577 dev->board_name = board->name;
578
579 s = &dev->subdevices[0];
580 /* ai subdevice */
581 s->type = COMEDI_SUBD_AI;
582 s->subdev_flags = SDF_READABLE | SDF_GROUND;
583 #if 1
584 s->n_chan = n_ai_chans;
585 #else
586 if (it->options[2])
587 s->n_chan = board->ad_chan;
588 else
589 s->n_chan = board->ad_chan / 2;
590 #endif
591 s->maxdata = (1 << board->adbits) - 1;
592 s->range_table = ai_range_lkup(board->adrangetype, it->options[3]);
593 s->insn_read = dt2801_ai_insn_read;
594
595 s = &dev->subdevices[1];
596 /* ao subdevice */
597 s->type = COMEDI_SUBD_AO;
598 s->subdev_flags = SDF_WRITABLE;
599 s->n_chan = 2;
600 s->maxdata = (1 << board->dabits) - 1;
601 s->range_table_list = devpriv->dac_range_types;
602 devpriv->dac_range_types[0] = dac_range_lkup(it->options[4]);
603 devpriv->dac_range_types[1] = dac_range_lkup(it->options[5]);
604 s->insn_write = dt2801_ao_insn_write;
605
606 ret = comedi_alloc_subdev_readback(s);
607 if (ret)
608 return ret;
609
610 s = &dev->subdevices[2];
611 /* 1st digital subdevice */
612 s->type = COMEDI_SUBD_DIO;
613 s->subdev_flags = SDF_READABLE | SDF_WRITABLE;
614 s->n_chan = 8;
615 s->maxdata = 1;
616 s->range_table = &range_digital;
617 s->insn_bits = dt2801_dio_insn_bits;
618 s->insn_config = dt2801_dio_insn_config;
619
620 s = &dev->subdevices[3];
621 /* 2nd digital subdevice */
622 s->type = COMEDI_SUBD_DIO;
623 s->subdev_flags = SDF_READABLE | SDF_WRITABLE;
624 s->n_chan = 8;
625 s->maxdata = 1;
626 s->range_table = &range_digital;
627 s->insn_bits = dt2801_dio_insn_bits;
628 s->insn_config = dt2801_dio_insn_config;
629
630 ret = 0;
631 out:
632 return ret;
633 }
634
635 static struct comedi_driver dt2801_driver = {
636 .driver_name = "dt2801",
637 .module = THIS_MODULE,
638 .attach = dt2801_attach,
639 .detach = comedi_legacy_detach,
640 };
641 module_comedi_driver(dt2801_driver);
642
643 MODULE_AUTHOR("Comedi https://www.comedi.org");
644 MODULE_DESCRIPTION("Comedi low-level driver");
645 MODULE_LICENSE("GPL");
646