1// SPDX-License-Identifier: BSD-3-Clause 2 3#include <dt-bindings/iio/qcom,spmi-vadc.h> 4#include <dt-bindings/input/input.h> 5#include <dt-bindings/input/linux-event-codes.h> 6#include <dt-bindings/interrupt-controller/irq.h> 7#include <dt-bindings/spmi/spmi.h> 8 9/ { 10 thermal-zones { 11 pm6125-thermal { 12 polling-delay-passive = <100>; 13 polling-delay = <0>; 14 15 thermal-sensors = <&pm6125_temp>; 16 17 trips { 18 trip0 { 19 temperature = <95000>; 20 hysteresis = <0>; 21 type = "passive"; 22 }; 23 24 trip1 { 25 temperature = <115000>; 26 hysteresis = <0>; 27 type = "hot"; 28 }; 29 30 trip2 { 31 temperature = <145000>; 32 hysteresis = <0>; 33 type = "critical"; 34 }; 35 }; 36 }; 37 }; 38}; 39 40&spmi_bus { 41 pmic@0 { 42 compatible = "qcom,pm6125", "qcom,spmi-pmic"; 43 reg = <0x0 SPMI_USID>; 44 #address-cells = <1>; 45 #size-cells = <0>; 46 47 pm6125_pon: pon@800 { 48 compatible = "qcom,pm8998-pon"; 49 reg = <0x800>; 50 mode-bootloader = <0x2>; 51 mode-recovery = <0x1>; 52 53 pon_pwrkey: pwrkey { 54 compatible = "qcom,pm8941-pwrkey"; 55 interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>; 56 debounce = <15625>; 57 linux,code = <KEY_POWER>; 58 bias-pull-up; 59 status = "disabled"; 60 }; 61 62 pon_resin: resin { 63 compatible = "qcom,pm8941-resin"; 64 interrupts = <0x0 0x8 0x1 IRQ_TYPE_EDGE_BOTH>; 65 debounce = <15625>; 66 bias-pull-up; 67 status = "disabled"; 68 }; 69 }; 70 71 pm6125_temp: temp-alarm@2400 { 72 compatible = "qcom,spmi-temp-alarm"; 73 reg = <0x2400>; 74 interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_RISING>; 75 io-channels = <&pm6125_adc ADC5_DIE_TEMP>; 76 io-channel-names = "thermal"; 77 #thermal-sensor-cells = <0>; 78 }; 79 80 pm6125_adc: adc@3100 { 81 compatible = "qcom,spmi-adc5"; 82 reg = <0x3100>; 83 #address-cells = <1>; 84 #size-cells = <0>; 85 interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; 86 #io-channel-cells = <1>; 87 88 ref-gnd@0 { 89 reg = <ADC5_REF_GND>; 90 qcom,pre-scaling = <1 1>; 91 }; 92 93 vref-1p25@1 { 94 reg = <ADC5_1P25VREF>; 95 qcom,pre-scaling = <1 1>; 96 }; 97 98 die-temp@6 { 99 reg = <ADC5_DIE_TEMP>; 100 qcom,pre-scaling = <1 1>; 101 }; 102 103 vph-pwr@83 { 104 reg = <ADC5_VPH_PWR>; 105 qcom,pre-scaling = <1 3>; 106 }; 107 108 vcoin@85 { 109 reg = <ADC5_VCOIN>; 110 qcom,pre-scaling = <1 3>; 111 }; 112 113 xo-therm@4c { 114 reg = <ADC5_XO_THERM_100K_PU>; 115 qcom,pre-scaling = <1 1>; 116 qcom,hw-settle-time = <200>; 117 qcom,ratiometric; 118 }; 119 }; 120 121 pm6125_adc_tm: adc-tm@3500 { 122 compatible = "qcom,spmi-adc-tm5"; 123 reg = <0x3500>; 124 interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>; 125 #address-cells = <1>; 126 #size-cells = <0>; 127 #thermal-sensor-cells = <1>; 128 status = "disabled"; 129 }; 130 131 pm6125_rtc: rtc@6000 { 132 compatible = "qcom,pm8941-rtc"; 133 reg = <0x6000>, <0x6100>; 134 reg-names = "rtc", "alarm"; 135 interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>; 136 status = "disabled"; 137 }; 138 139 pm6125_gpio: gpio@c000 { 140 compatible = "qcom,pm6125-gpio", "qcom,spmi-gpio"; 141 reg = <0xc000>; 142 gpio-controller; 143 gpio-ranges = <&pm6125_gpio 0 0 9>; 144 #gpio-cells = <2>; 145 interrupt-controller; 146 #interrupt-cells = <2>; 147 }; 148 }; 149 150 pmic@1 { 151 compatible = "qcom,pm6125", "qcom,spmi-pmic"; 152 reg = <0x1 SPMI_USID>; 153 }; 154}; 155