1// SPDX-License-Identifier: BSD-3-Clause 2 3#include <dt-bindings/iio/qcom,spmi-vadc.h> 4#include <dt-bindings/input/input.h> 5#include <dt-bindings/input/linux-event-codes.h> 6#include <dt-bindings/interrupt-controller/irq.h> 7#include <dt-bindings/spmi/spmi.h> 8 9/ { 10 thermal-zones { 11 pm6125-thermal { 12 polling-delay-passive = <100>; 13 polling-delay = <0>; 14 15 thermal-sensors = <&pm6125_temp>; 16 17 trips { 18 trip0 { 19 temperature = <95000>; 20 hysteresis = <0>; 21 type = "passive"; 22 }; 23 24 trip1 { 25 temperature = <115000>; 26 hysteresis = <0>; 27 type = "hot"; 28 }; 29 30 trip2 { 31 temperature = <145000>; 32 hysteresis = <0>; 33 type = "critical"; 34 }; 35 }; 36 }; 37 }; 38}; 39 40&spmi_bus { 41 pmic@0 { 42 compatible = "qcom,pm6125", "qcom,spmi-pmic"; 43 reg = <0x0 SPMI_USID>; 44 #address-cells = <1>; 45 #size-cells = <0>; 46 47 pm6125_pon: pon@800 { 48 compatible = "qcom,pm8998-pon"; 49 reg = <0x800>; 50 mode-bootloader = <0x2>; 51 mode-recovery = <0x1>; 52 53 pon_pwrkey: pwrkey { 54 compatible = "qcom,pm8941-pwrkey"; 55 interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>; 56 debounce = <15625>; 57 linux,code = <KEY_POWER>; 58 bias-pull-up; 59 status = "disabled"; 60 }; 61 62 pon_resin: resin { 63 compatible = "qcom,pm8941-resin"; 64 interrupts = <0x0 0x8 0x1 IRQ_TYPE_EDGE_BOTH>; 65 debounce = <15625>; 66 bias-pull-up; 67 status = "disabled"; 68 }; 69 }; 70 71 pm6125_temp: temp-alarm@2400 { 72 compatible = "qcom,spmi-temp-alarm"; 73 reg = <0x2400>; 74 interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_RISING>; 75 io-channels = <&pm6125_adc ADC5_DIE_TEMP>; 76 io-channel-names = "thermal"; 77 #thermal-sensor-cells = <0>; 78 }; 79 80 pm6125_adc: adc@3100 { 81 compatible = "qcom,spmi-adc5"; 82 reg = <0x3100>; 83 #address-cells = <1>; 84 #size-cells = <0>; 85 interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; 86 #io-channel-cells = <1>; 87 88 channel@0 { 89 reg = <ADC5_REF_GND>; 90 qcom,pre-scaling = <1 1>; 91 label = "ref_gnd"; 92 }; 93 94 channel@1 { 95 reg = <ADC5_1P25VREF>; 96 qcom,pre-scaling = <1 1>; 97 label = "vref_1p25"; 98 }; 99 100 channel@6 { 101 reg = <ADC5_DIE_TEMP>; 102 qcom,pre-scaling = <1 1>; 103 label = "die_temp"; 104 }; 105 106 channel@83 { 107 reg = <ADC5_VPH_PWR>; 108 qcom,pre-scaling = <1 3>; 109 label = "vph_pwr"; 110 }; 111 112 channel@85 { 113 reg = <ADC5_VCOIN>; 114 qcom,pre-scaling = <1 3>; 115 label = "vcoin"; 116 }; 117 118 channel@4c { 119 reg = <ADC5_XO_THERM_100K_PU>; 120 qcom,pre-scaling = <1 1>; 121 qcom,hw-settle-time = <200>; 122 qcom,ratiometric; 123 label = "xo_therm"; 124 }; 125 }; 126 127 pm6125_adc_tm: adc-tm@3500 { 128 compatible = "qcom,spmi-adc-tm5"; 129 reg = <0x3500>; 130 interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>; 131 #address-cells = <1>; 132 #size-cells = <0>; 133 #thermal-sensor-cells = <1>; 134 status = "disabled"; 135 }; 136 137 pm6125_rtc: rtc@6000 { 138 compatible = "qcom,pm8941-rtc"; 139 reg = <0x6000>, <0x6100>; 140 reg-names = "rtc", "alarm"; 141 interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>; 142 status = "disabled"; 143 }; 144 145 pm6125_gpios: gpio@c000 { 146 compatible = "qcom,pm6125-gpio", "qcom,spmi-gpio"; 147 reg = <0xc000>; 148 gpio-controller; 149 gpio-ranges = <&pm6125_gpios 0 0 9>; 150 #gpio-cells = <2>; 151 interrupt-controller; 152 #interrupt-cells = <2>; 153 }; 154 }; 155 156 pmic@1 { 157 compatible = "qcom,pm6125", "qcom,spmi-pmic"; 158 reg = <0x1 SPMI_USID>; 159 }; 160}; 161