1// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) 2/* 3 * IPQ6018 SoC device tree source 4 * 5 * Copyright (c) 2019, The Linux Foundation. All rights reserved. 6 */ 7 8#include <dt-bindings/interrupt-controller/arm-gic.h> 9#include <dt-bindings/clock/qcom,gcc-ipq6018.h> 10#include <dt-bindings/reset/qcom,gcc-ipq6018.h> 11#include <dt-bindings/clock/qcom,apss-ipq.h> 12 13/ { 14 #address-cells = <2>; 15 #size-cells = <2>; 16 interrupt-parent = <&intc>; 17 18 clocks { 19 sleep_clk: sleep-clk { 20 compatible = "fixed-clock"; 21 clock-frequency = <32000>; 22 #clock-cells = <0>; 23 }; 24 25 xo: xo { 26 compatible = "fixed-clock"; 27 clock-frequency = <24000000>; 28 #clock-cells = <0>; 29 }; 30 }; 31 32 cpus: cpus { 33 #address-cells = <1>; 34 #size-cells = <0>; 35 36 CPU0: cpu@0 { 37 device_type = "cpu"; 38 compatible = "arm,cortex-a53"; 39 reg = <0x0>; 40 enable-method = "psci"; 41 next-level-cache = <&L2_0>; 42 clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>; 43 clock-names = "cpu"; 44 operating-points-v2 = <&cpu_opp_table>; 45 cpu-supply = <&ipq6018_s2>; 46 }; 47 48 CPU1: cpu@1 { 49 device_type = "cpu"; 50 compatible = "arm,cortex-a53"; 51 enable-method = "psci"; 52 reg = <0x1>; 53 next-level-cache = <&L2_0>; 54 clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>; 55 clock-names = "cpu"; 56 operating-points-v2 = <&cpu_opp_table>; 57 cpu-supply = <&ipq6018_s2>; 58 }; 59 60 CPU2: cpu@2 { 61 device_type = "cpu"; 62 compatible = "arm,cortex-a53"; 63 enable-method = "psci"; 64 reg = <0x2>; 65 next-level-cache = <&L2_0>; 66 clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>; 67 clock-names = "cpu"; 68 operating-points-v2 = <&cpu_opp_table>; 69 cpu-supply = <&ipq6018_s2>; 70 }; 71 72 CPU3: cpu@3 { 73 device_type = "cpu"; 74 compatible = "arm,cortex-a53"; 75 enable-method = "psci"; 76 reg = <0x3>; 77 next-level-cache = <&L2_0>; 78 clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>; 79 clock-names = "cpu"; 80 operating-points-v2 = <&cpu_opp_table>; 81 cpu-supply = <&ipq6018_s2>; 82 }; 83 84 L2_0: l2-cache { 85 compatible = "cache"; 86 cache-level = <0x2>; 87 }; 88 }; 89 90 cpu_opp_table: cpu_opp_table { 91 compatible = "operating-points-v2"; 92 opp-shared; 93 94 opp-864000000 { 95 opp-hz = /bits/ 64 <864000000>; 96 opp-microvolt = <725000>; 97 clock-latency-ns = <200000>; 98 }; 99 opp-1056000000 { 100 opp-hz = /bits/ 64 <1056000000>; 101 opp-microvolt = <787500>; 102 clock-latency-ns = <200000>; 103 }; 104 opp-1320000000 { 105 opp-hz = /bits/ 64 <1320000000>; 106 opp-microvolt = <862500>; 107 clock-latency-ns = <200000>; 108 }; 109 opp-1440000000 { 110 opp-hz = /bits/ 64 <1440000000>; 111 opp-microvolt = <925000>; 112 clock-latency-ns = <200000>; 113 }; 114 opp-1608000000 { 115 opp-hz = /bits/ 64 <1608000000>; 116 opp-microvolt = <987500>; 117 clock-latency-ns = <200000>; 118 }; 119 opp-1800000000 { 120 opp-hz = /bits/ 64 <1800000000>; 121 opp-microvolt = <1062500>; 122 clock-latency-ns = <200000>; 123 }; 124 }; 125 126 firmware { 127 scm { 128 compatible = "qcom,scm"; 129 }; 130 }; 131 132 tcsr_mutex: hwlock { 133 compatible = "qcom,tcsr-mutex"; 134 syscon = <&tcsr_mutex_regs 0 0x80>; 135 #hwlock-cells = <1>; 136 }; 137 138 pmuv8: pmu { 139 compatible = "arm,cortex-a53-pmu"; 140 interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | 141 IRQ_TYPE_LEVEL_HIGH)>; 142 }; 143 144 psci: psci { 145 compatible = "arm,psci-1.0"; 146 method = "smc"; 147 }; 148 149 reserved-memory { 150 #address-cells = <2>; 151 #size-cells = <2>; 152 ranges; 153 154 rpm_msg_ram: memory@60000 { 155 reg = <0x0 0x60000 0x0 0x6000>; 156 no-map; 157 }; 158 159 tz: memory@4a600000 { 160 reg = <0x0 0x4a600000 0x0 0x00400000>; 161 no-map; 162 }; 163 164 smem_region: memory@4aa00000 { 165 reg = <0x0 0x4aa00000 0x0 0x00100000>; 166 no-map; 167 }; 168 169 q6_region: memory@4ab00000 { 170 reg = <0x0 0x4ab00000 0x0 0x05500000>; 171 no-map; 172 }; 173 }; 174 175 smem { 176 compatible = "qcom,smem"; 177 memory-region = <&smem_region>; 178 hwlocks = <&tcsr_mutex 0>; 179 }; 180 181 soc: soc { 182 #address-cells = <2>; 183 #size-cells = <2>; 184 ranges = <0 0 0 0 0x0 0xffffffff>; 185 dma-ranges; 186 compatible = "simple-bus"; 187 188 prng: qrng@e1000 { 189 compatible = "qcom,prng-ee"; 190 reg = <0x0 0xe3000 0x0 0x1000>; 191 clocks = <&gcc GCC_PRNG_AHB_CLK>; 192 clock-names = "core"; 193 }; 194 195 cryptobam: dma-controller@704000 { 196 compatible = "qcom,bam-v1.7.0"; 197 reg = <0x0 0x00704000 0x0 0x20000>; 198 interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>; 199 clocks = <&gcc GCC_CRYPTO_AHB_CLK>; 200 clock-names = "bam_clk"; 201 #dma-cells = <1>; 202 qcom,ee = <1>; 203 qcom,controlled-remotely; 204 }; 205 206 crypto: crypto@73a000 { 207 compatible = "qcom,crypto-v5.1"; 208 reg = <0x0 0x0073a000 0x0 0x6000>; 209 clocks = <&gcc GCC_CRYPTO_AHB_CLK>, 210 <&gcc GCC_CRYPTO_AXI_CLK>, 211 <&gcc GCC_CRYPTO_CLK>; 212 clock-names = "iface", "bus", "core"; 213 dmas = <&cryptobam 2>, <&cryptobam 3>; 214 dma-names = "rx", "tx"; 215 }; 216 217 tlmm: pinctrl@1000000 { 218 compatible = "qcom,ipq6018-pinctrl"; 219 reg = <0x0 0x01000000 0x0 0x300000>; 220 interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; 221 gpio-controller; 222 #gpio-cells = <2>; 223 gpio-ranges = <&tlmm 0 0 80>; 224 interrupt-controller; 225 #interrupt-cells = <2>; 226 227 serial_3_pins: serial3-pinmux { 228 pins = "gpio44", "gpio45"; 229 function = "blsp2_uart"; 230 drive-strength = <8>; 231 bias-pull-down; 232 }; 233 234 qpic_pins: qpic-pins { 235 pins = "gpio1", "gpio3", "gpio4", 236 "gpio5", "gpio6", "gpio7", 237 "gpio8", "gpio10", "gpio11", 238 "gpio12", "gpio13", "gpio14", 239 "gpio15", "gpio17"; 240 function = "qpic_pad"; 241 drive-strength = <8>; 242 bias-disable; 243 }; 244 }; 245 246 gcc: gcc@1800000 { 247 compatible = "qcom,gcc-ipq6018"; 248 reg = <0x0 0x01800000 0x0 0x80000>; 249 clocks = <&xo>, <&sleep_clk>; 250 clock-names = "xo", "sleep_clk"; 251 #clock-cells = <1>; 252 #reset-cells = <1>; 253 }; 254 255 tcsr_mutex_regs: syscon@1905000 { 256 compatible = "syscon"; 257 reg = <0x0 0x01905000 0x0 0x8000>; 258 }; 259 260 tcsr: syscon@1937000 { 261 compatible = "syscon"; 262 reg = <0x0 0x01937000 0x0 0x21000>; 263 }; 264 265 blsp_dma: dma-controller@7884000 { 266 compatible = "qcom,bam-v1.7.0"; 267 reg = <0x0 0x07884000 0x0 0x2b000>; 268 interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>; 269 clocks = <&gcc GCC_BLSP1_AHB_CLK>; 270 clock-names = "bam_clk"; 271 #dma-cells = <1>; 272 qcom,ee = <0>; 273 }; 274 275 blsp1_uart3: serial@78b1000 { 276 compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; 277 reg = <0x0 0x078b1000 0x0 0x200>; 278 interrupts = <GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>; 279 clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>, 280 <&gcc GCC_BLSP1_AHB_CLK>; 281 clock-names = "core", "iface"; 282 status = "disabled"; 283 }; 284 285 spi_0: spi@78b5000 { 286 compatible = "qcom,spi-qup-v2.2.1"; 287 #address-cells = <1>; 288 #size-cells = <0>; 289 reg = <0x0 0x078b5000 0x0 0x600>; 290 interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; 291 spi-max-frequency = <50000000>; 292 clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>, 293 <&gcc GCC_BLSP1_AHB_CLK>; 294 clock-names = "core", "iface"; 295 dmas = <&blsp_dma 12>, <&blsp_dma 13>; 296 dma-names = "tx", "rx"; 297 status = "disabled"; 298 }; 299 300 spi_1: spi@78b6000 { 301 compatible = "qcom,spi-qup-v2.2.1"; 302 #address-cells = <1>; 303 #size-cells = <0>; 304 reg = <0x0 0x078b6000 0x0 0x600>; 305 interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; 306 spi-max-frequency = <50000000>; 307 clocks = <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>, 308 <&gcc GCC_BLSP1_AHB_CLK>; 309 clock-names = "core", "iface"; 310 dmas = <&blsp_dma 14>, <&blsp_dma 15>; 311 dma-names = "tx", "rx"; 312 status = "disabled"; 313 }; 314 315 i2c_0: i2c@78b6000 { 316 compatible = "qcom,i2c-qup-v2.2.1"; 317 #address-cells = <1>; 318 #size-cells = <0>; 319 reg = <0x0 0x078b6000 0x0 0x600>; 320 interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; 321 clocks = <&gcc GCC_BLSP1_AHB_CLK>, 322 <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>; 323 clock-names = "iface", "core"; 324 clock-frequency = <400000>; 325 dmas = <&blsp_dma 15>, <&blsp_dma 14>; 326 dma-names = "rx", "tx"; 327 status = "disabled"; 328 }; 329 330 i2c_1: i2c@78b7000 { /* BLSP1 QUP2 */ 331 compatible = "qcom,i2c-qup-v2.2.1"; 332 #address-cells = <1>; 333 #size-cells = <0>; 334 reg = <0x0 0x078b7000 0x0 0x600>; 335 interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; 336 clocks = <&gcc GCC_BLSP1_AHB_CLK>, 337 <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>; 338 clock-names = "iface", "core"; 339 clock-frequency = <400000>; 340 dmas = <&blsp_dma 17>, <&blsp_dma 16>; 341 dma-names = "rx", "tx"; 342 status = "disabled"; 343 }; 344 345 qpic_bam: dma-controller@7984000 { 346 compatible = "qcom,bam-v1.7.0"; 347 reg = <0x0 0x07984000 0x0 0x1a000>; 348 interrupts = <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>; 349 clocks = <&gcc GCC_QPIC_AHB_CLK>; 350 clock-names = "bam_clk"; 351 #dma-cells = <1>; 352 qcom,ee = <0>; 353 status = "disabled"; 354 }; 355 356 qpic_nand: nand@79b0000 { 357 compatible = "qcom,ipq6018-nand"; 358 reg = <0x0 0x079b0000 0x0 0x10000>; 359 #address-cells = <1>; 360 #size-cells = <0>; 361 clocks = <&gcc GCC_QPIC_CLK>, 362 <&gcc GCC_QPIC_AHB_CLK>; 363 clock-names = "core", "aon"; 364 365 dmas = <&qpic_bam 0>, 366 <&qpic_bam 1>, 367 <&qpic_bam 2>; 368 dma-names = "tx", "rx", "cmd"; 369 pinctrl-0 = <&qpic_pins>; 370 pinctrl-names = "default"; 371 status = "disabled"; 372 }; 373 374 intc: interrupt-controller@b000000 { 375 compatible = "qcom,msm-qgic2"; 376 #address-cells = <2>; 377 #size-cells = <2>; 378 interrupt-controller; 379 #interrupt-cells = <0x3>; 380 reg = <0x0 0x0b000000 0x0 0x1000>, /*GICD*/ 381 <0x0 0x0b002000 0x0 0x1000>, /*GICC*/ 382 <0x0 0x0b001000 0x0 0x1000>, /*GICH*/ 383 <0x0 0x0b004000 0x0 0x1000>; /*GICV*/ 384 interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; 385 ranges = <0 0 0 0xb00a000 0 0xffd>; 386 387 v2m@0 { 388 compatible = "arm,gic-v2m-frame"; 389 msi-controller; 390 reg = <0x0 0x0 0x0 0xffd>; 391 }; 392 }; 393 394 pcie_phy: phy@84000 { 395 compatible = "qcom,ipq6018-qmp-pcie-phy"; 396 reg = <0x0 0x84000 0x0 0x1bc>; /* Serdes PLL */ 397 status = "disabled"; 398 #address-cells = <2>; 399 #size-cells = <2>; 400 ranges; 401 402 clocks = <&gcc GCC_PCIE0_AUX_CLK>, 403 <&gcc GCC_PCIE0_AHB_CLK>; 404 clock-names = "aux", "cfg_ahb"; 405 406 resets = <&gcc GCC_PCIE0_PHY_BCR>, 407 <&gcc GCC_PCIE0PHY_PHY_BCR>; 408 reset-names = "phy", 409 "common"; 410 411 pcie_phy0: phy@84200 { 412 reg = <0x0 0x84200 0x0 0x16c>, /* Serdes Tx */ 413 <0x0 0x84400 0x0 0x200>, /* Serdes Rx */ 414 <0x0 0x84800 0x0 0x4f4>; /* PCS: Lane0, COM, PCIE */ 415 #phy-cells = <0>; 416 417 clocks = <&gcc GCC_PCIE0_PIPE_CLK>; 418 clock-names = "pipe0"; 419 clock-output-names = "gcc_pcie0_pipe_clk_src"; 420 #clock-cells = <0>; 421 }; 422 }; 423 424 pcie0: pci@20000000 { 425 compatible = "qcom,pcie-ipq6018"; 426 reg = <0x0 0x20000000 0x0 0xf1d>, 427 <0x0 0x20000f20 0x0 0xa8>, 428 <0x0 0x20001000 0x0 0x1000>, 429 <0x0 0x80000 0x0 0x4000>, 430 <0x0 0x20100000 0x0 0x1000>; 431 reg-names = "dbi", "elbi", "atu", "parf", "config"; 432 433 device_type = "pci"; 434 linux,pci-domain = <0>; 435 bus-range = <0x00 0xff>; 436 num-lanes = <1>; 437 max-link-speed = <3>; 438 #address-cells = <3>; 439 #size-cells = <2>; 440 441 phys = <&pcie_phy0>; 442 phy-names = "pciephy"; 443 444 ranges = <0x81000000 0 0x20200000 0 0x20200000 445 0 0x10000>, /* downstream I/O */ 446 <0x82000000 0 0x20220000 0 0x20220000 447 0 0xfde0000>; /* non-prefetchable memory */ 448 449 interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>; 450 interrupt-names = "msi"; 451 452 #interrupt-cells = <1>; 453 interrupt-map-mask = <0 0 0 0x7>; 454 interrupt-map = <0 0 0 1 &intc 0 75 455 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ 456 <0 0 0 2 &intc 0 78 457 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ 458 <0 0 0 3 &intc 0 79 459 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ 460 <0 0 0 4 &intc 0 83 461 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ 462 463 clocks = <&gcc GCC_SYS_NOC_PCIE0_AXI_CLK>, 464 <&gcc GCC_PCIE0_AXI_M_CLK>, 465 <&gcc GCC_PCIE0_AXI_S_CLK>, 466 <&gcc GCC_PCIE0_AXI_S_BRIDGE_CLK>, 467 <&gcc PCIE0_RCHNG_CLK>; 468 clock-names = "iface", 469 "axi_m", 470 "axi_s", 471 "axi_bridge", 472 "rchng"; 473 474 resets = <&gcc GCC_PCIE0_PIPE_ARES>, 475 <&gcc GCC_PCIE0_SLEEP_ARES>, 476 <&gcc GCC_PCIE0_CORE_STICKY_ARES>, 477 <&gcc GCC_PCIE0_AXI_MASTER_ARES>, 478 <&gcc GCC_PCIE0_AXI_SLAVE_ARES>, 479 <&gcc GCC_PCIE0_AHB_ARES>, 480 <&gcc GCC_PCIE0_AXI_MASTER_STICKY_ARES>, 481 <&gcc GCC_PCIE0_AXI_SLAVE_STICKY_ARES>; 482 reset-names = "pipe", 483 "sleep", 484 "sticky", 485 "axi_m", 486 "axi_s", 487 "ahb", 488 "axi_m_sticky", 489 "axi_s_sticky"; 490 491 status = "disabled"; 492 }; 493 494 watchdog@b017000 { 495 compatible = "qcom,kpss-wdt"; 496 interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>; 497 reg = <0x0 0x0b017000 0x0 0x40>; 498 clocks = <&sleep_clk>; 499 timeout-sec = <10>; 500 }; 501 502 apcs_glb: mailbox@b111000 { 503 compatible = "qcom,ipq6018-apcs-apps-global"; 504 reg = <0x0 0x0b111000 0x0 0x1000>; 505 #clock-cells = <1>; 506 clocks = <&a53pll>, <&xo>; 507 clock-names = "pll", "xo"; 508 #mbox-cells = <1>; 509 }; 510 511 a53pll: clock@b116000 { 512 compatible = "qcom,ipq6018-a53pll"; 513 reg = <0x0 0x0b116000 0x0 0x40>; 514 #clock-cells = <0>; 515 clocks = <&xo>; 516 clock-names = "xo"; 517 }; 518 519 timer { 520 compatible = "arm,armv8-timer"; 521 interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, 522 <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, 523 <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, 524 <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; 525 }; 526 527 timer@b120000 { 528 #address-cells = <2>; 529 #size-cells = <2>; 530 ranges; 531 compatible = "arm,armv7-timer-mem"; 532 reg = <0x0 0x0b120000 0x0 0x1000>; 533 534 frame@b120000 { 535 frame-number = <0>; 536 interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, 537 <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; 538 reg = <0x0 0x0b121000 0x0 0x1000>, 539 <0x0 0x0b122000 0x0 0x1000>; 540 }; 541 542 frame@b123000 { 543 frame-number = <1>; 544 interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; 545 reg = <0x0 0xb123000 0x0 0x1000>; 546 status = "disabled"; 547 }; 548 549 frame@b124000 { 550 frame-number = <2>; 551 interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; 552 reg = <0x0 0x0b124000 0x0 0x1000>; 553 status = "disabled"; 554 }; 555 556 frame@b125000 { 557 frame-number = <3>; 558 interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; 559 reg = <0x0 0x0b125000 0x0 0x1000>; 560 status = "disabled"; 561 }; 562 563 frame@b126000 { 564 frame-number = <4>; 565 interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; 566 reg = <0x0 0x0b126000 0x0 0x1000>; 567 status = "disabled"; 568 }; 569 570 frame@b127000 { 571 frame-number = <5>; 572 interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; 573 reg = <0x0 0x0b127000 0x0 0x1000>; 574 status = "disabled"; 575 }; 576 577 frame@b128000 { 578 frame-number = <6>; 579 interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; 580 reg = <0x0 0x0b128000 0x0 0x1000>; 581 status = "disabled"; 582 }; 583 }; 584 585 q6v5_wcss: remoteproc@cd00000 { 586 compatible = "qcom,ipq6018-wcss-pil"; 587 reg = <0x0 0x0cd00000 0x0 0x4040>, 588 <0x0 0x004ab000 0x0 0x20>; 589 reg-names = "qdsp6", 590 "rmb"; 591 interrupts-extended = <&intc GIC_SPI 325 IRQ_TYPE_EDGE_RISING>, 592 <&wcss_smp2p_in 0 0>, 593 <&wcss_smp2p_in 1 0>, 594 <&wcss_smp2p_in 2 0>, 595 <&wcss_smp2p_in 3 0>; 596 interrupt-names = "wdog", 597 "fatal", 598 "ready", 599 "handover", 600 "stop-ack"; 601 602 resets = <&gcc GCC_WCSSAON_RESET>, 603 <&gcc GCC_WCSS_BCR>, 604 <&gcc GCC_WCSS_Q6_BCR>; 605 606 reset-names = "wcss_aon_reset", 607 "wcss_reset", 608 "wcss_q6_reset"; 609 610 clocks = <&gcc GCC_PRNG_AHB_CLK>; 611 clock-names = "prng"; 612 613 qcom,halt-regs = <&tcsr 0x18000 0x1b000 0xe000>; 614 615 qcom,smem-states = <&wcss_smp2p_out 0>, 616 <&wcss_smp2p_out 1>; 617 qcom,smem-state-names = "shutdown", 618 "stop"; 619 620 memory-region = <&q6_region>; 621 622 glink-edge { 623 interrupts = <GIC_SPI 321 IRQ_TYPE_EDGE_RISING>; 624 qcom,remote-pid = <1>; 625 mboxes = <&apcs_glb 8>; 626 627 qrtr_requests { 628 qcom,glink-channels = "IPCRTR"; 629 }; 630 }; 631 }; 632 633 qusb_phy_1: qusb@59000 { 634 compatible = "qcom,ipq6018-qusb2-phy"; 635 reg = <0x0 0x059000 0x0 0x180>; 636 #phy-cells = <0>; 637 638 clocks = <&gcc GCC_USB1_PHY_CFG_AHB_CLK>, 639 <&xo>; 640 clock-names = "cfg_ahb", "ref"; 641 642 resets = <&gcc GCC_QUSB2_1_PHY_BCR>; 643 status = "disabled"; 644 }; 645 646 usb2: usb2@7000000 { 647 compatible = "qcom,ipq6018-dwc3", "qcom,dwc3"; 648 reg = <0x0 0x070F8800 0x0 0x400>; 649 #address-cells = <2>; 650 #size-cells = <2>; 651 ranges; 652 clocks = <&gcc GCC_USB1_MASTER_CLK>, 653 <&gcc GCC_USB1_SLEEP_CLK>, 654 <&gcc GCC_USB1_MOCK_UTMI_CLK>; 655 clock-names = "master", 656 "sleep", 657 "mock_utmi"; 658 659 assigned-clocks = <&gcc GCC_USB1_MASTER_CLK>, 660 <&gcc GCC_USB1_MOCK_UTMI_CLK>; 661 assigned-clock-rates = <133330000>, 662 <24000000>; 663 resets = <&gcc GCC_USB1_BCR>; 664 status = "disabled"; 665 666 dwc_1: usb@7000000 { 667 compatible = "snps,dwc3"; 668 reg = <0x0 0x7000000 0x0 0xcd00>; 669 interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; 670 phys = <&qusb_phy_1>; 671 phy-names = "usb2-phy"; 672 tx-fifo-resize; 673 snps,is-utmi-l1-suspend; 674 snps,hird-threshold = /bits/ 8 <0x0>; 675 snps,dis_u2_susphy_quirk; 676 snps,dis_u3_susphy_quirk; 677 dr_mode = "host"; 678 }; 679 }; 680 681 ssphy_0: ssphy@78000 { 682 compatible = "qcom,ipq6018-qmp-usb3-phy"; 683 reg = <0x0 0x78000 0x0 0x1C4>; 684 #address-cells = <2>; 685 #size-cells = <2>; 686 #clock-cells = <1>; 687 ranges; 688 689 clocks = <&gcc GCC_USB0_AUX_CLK>, 690 <&gcc GCC_USB0_PHY_CFG_AHB_CLK>, <&xo>; 691 clock-names = "aux", "cfg_ahb", "ref"; 692 693 resets = <&gcc GCC_USB0_PHY_BCR>, 694 <&gcc GCC_USB3PHY_0_PHY_BCR>; 695 reset-names = "phy","common"; 696 status = "disabled"; 697 698 usb0_ssphy: lane@78200 { 699 reg = <0x0 0x00078200 0x0 0x130>, /* Tx */ 700 <0x0 0x00078400 0x0 0x200>, /* Rx */ 701 <0x0 0x00078800 0x0 0x1F8>, /* PCS */ 702 <0x0 0x00078600 0x0 0x044>; /* PCS misc */ 703 #phy-cells = <0>; 704 clocks = <&gcc GCC_USB0_PIPE_CLK>; 705 clock-names = "pipe0"; 706 clock-output-names = "gcc_usb0_pipe_clk_src"; 707 }; 708 }; 709 710 qusb_phy_0: qusb@79000 { 711 compatible = "qcom,ipq6018-qusb2-phy"; 712 reg = <0x0 0x079000 0x0 0x180>; 713 #phy-cells = <0>; 714 715 clocks = <&gcc GCC_USB0_PHY_CFG_AHB_CLK>, 716 <&xo>; 717 clock-names = "cfg_ahb", "ref"; 718 719 resets = <&gcc GCC_QUSB2_0_PHY_BCR>; 720 status = "disabled"; 721 }; 722 723 usb3: usb3@8A00000 { 724 compatible = "qcom,ipq6018-dwc3", "qcom,dwc3"; 725 reg = <0x0 0x8AF8800 0x0 0x400>; 726 #address-cells = <2>; 727 #size-cells = <2>; 728 ranges; 729 730 clocks = <&gcc GCC_SYS_NOC_USB0_AXI_CLK>, 731 <&gcc GCC_USB0_MASTER_CLK>, 732 <&gcc GCC_USB0_SLEEP_CLK>, 733 <&gcc GCC_USB0_MOCK_UTMI_CLK>; 734 clock-names = "sys_noc_axi", 735 "master", 736 "sleep", 737 "mock_utmi"; 738 739 assigned-clocks = <&gcc GCC_SYS_NOC_USB0_AXI_CLK>, 740 <&gcc GCC_USB0_MASTER_CLK>, 741 <&gcc GCC_USB0_MOCK_UTMI_CLK>; 742 assigned-clock-rates = <133330000>, 743 <133330000>, 744 <20000000>; 745 746 resets = <&gcc GCC_USB0_BCR>; 747 status = "disabled"; 748 749 dwc_0: usb@8A00000 { 750 compatible = "snps,dwc3"; 751 reg = <0x0 0x8A00000 0x0 0xcd00>; 752 interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>; 753 phys = <&qusb_phy_0>, <&usb0_ssphy>; 754 phy-names = "usb2-phy", "usb3-phy"; 755 clocks = <&xo>; 756 clock-names = "ref"; 757 tx-fifo-resize; 758 snps,is-utmi-l1-suspend; 759 snps,hird-threshold = /bits/ 8 <0x0>; 760 snps,dis_u2_susphy_quirk; 761 snps,dis_u3_susphy_quirk; 762 dr_mode = "host"; 763 }; 764 }; 765 }; 766 767 wcss: wcss-smp2p { 768 compatible = "qcom,smp2p"; 769 qcom,smem = <435>, <428>; 770 771 interrupt-parent = <&intc>; 772 interrupts = <GIC_SPI 322 IRQ_TYPE_EDGE_RISING>; 773 774 mboxes = <&apcs_glb 9>; 775 776 qcom,local-pid = <0>; 777 qcom,remote-pid = <1>; 778 779 wcss_smp2p_out: master-kernel { 780 qcom,entry-name = "master-kernel"; 781 #qcom,smem-state-cells = <1>; 782 }; 783 784 wcss_smp2p_in: slave-kernel { 785 qcom,entry-name = "slave-kernel"; 786 interrupt-controller; 787 #interrupt-cells = <2>; 788 }; 789 }; 790 791 rpm-glink { 792 compatible = "qcom,glink-rpm"; 793 interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>; 794 qcom,rpm-msg-ram = <&rpm_msg_ram>; 795 mboxes = <&apcs_glb 0>; 796 797 rpm_requests: glink-channel { 798 compatible = "qcom,rpm-ipq6018"; 799 qcom,glink-channels = "rpm_requests"; 800 801 regulators { 802 compatible = "qcom,rpm-mp5496-regulators"; 803 804 ipq6018_s2: s2 { 805 regulator-min-microvolt = <725000>; 806 regulator-max-microvolt = <1062500>; 807 regulator-always-on; 808 }; 809 }; 810 }; 811 }; 812}; 813