1# SPDX-License-Identifier: GPL-2.0 2config ARM 3 bool 4 default y 5 select ARCH_32BIT_OFF_T 6 select ARCH_HAS_BINFMT_FLAT 7 select ARCH_HAS_DEBUG_VIRTUAL if MMU 8 select ARCH_HAS_DMA_WRITE_COMBINE if !ARM_DMA_MEM_BUFFERABLE 9 select ARCH_HAS_ELF_RANDOMIZE 10 select ARCH_HAS_FORTIFY_SOURCE 11 select ARCH_HAS_KEEPINITRD 12 select ARCH_HAS_KCOV 13 select ARCH_HAS_MEMBARRIER_SYNC_CORE 14 select ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE 15 select ARCH_HAS_PTE_SPECIAL if ARM_LPAE 16 select ARCH_HAS_PHYS_TO_DMA 17 select ARCH_HAS_SETUP_DMA_OPS 18 select ARCH_HAS_SET_MEMORY 19 select ARCH_HAS_STRICT_KERNEL_RWX if MMU && !XIP_KERNEL 20 select ARCH_HAS_STRICT_MODULE_RWX if MMU 21 select ARCH_HAS_SYNC_DMA_FOR_DEVICE if SWIOTLB || !MMU 22 select ARCH_HAS_SYNC_DMA_FOR_CPU if SWIOTLB || !MMU 23 select ARCH_HAS_TEARDOWN_DMA_OPS if MMU 24 select ARCH_HAS_TICK_BROADCAST if GENERIC_CLOCKEVENTS_BROADCAST 25 select ARCH_HAVE_CUSTOM_GPIO_H 26 select ARCH_HAVE_NMI_SAFE_CMPXCHG if CPU_V7 || CPU_V7M || CPU_V6K 27 select ARCH_HAS_GCOV_PROFILE_ALL 28 select ARCH_KEEP_MEMBLOCK 29 select ARCH_MIGHT_HAVE_PC_PARPORT 30 select ARCH_NO_SG_CHAIN if !ARM_HAS_SG_CHAIN 31 select ARCH_OPTIONAL_KERNEL_RWX if ARCH_HAS_STRICT_KERNEL_RWX 32 select ARCH_OPTIONAL_KERNEL_RWX_DEFAULT if CPU_V7 33 select ARCH_SUPPORTS_ATOMIC_RMW 34 select ARCH_SUPPORTS_HUGETLBFS if ARM_LPAE 35 select ARCH_USE_BUILTIN_BSWAP 36 select ARCH_USE_CMPXCHG_LOCKREF 37 select ARCH_USE_MEMTEST 38 select ARCH_WANT_DEFAULT_TOPDOWN_MMAP_LAYOUT if MMU 39 select ARCH_WANT_IPC_PARSE_VERSION 40 select ARCH_WANT_LD_ORPHAN_WARN 41 select BINFMT_FLAT_ARGVP_ENVP_ON_STACK 42 select BUILDTIME_TABLE_SORT if MMU 43 select CLONE_BACKWARDS 44 select CPU_PM if SUSPEND || CPU_IDLE 45 select DCACHE_WORD_ACCESS if HAVE_EFFICIENT_UNALIGNED_ACCESS 46 select DMA_DECLARE_COHERENT 47 select DMA_GLOBAL_POOL if !MMU 48 select DMA_OPS 49 select DMA_REMAP if MMU 50 select EDAC_SUPPORT 51 select EDAC_ATOMIC_SCRUB 52 select GENERIC_ALLOCATOR 53 select GENERIC_ARCH_TOPOLOGY if ARM_CPU_TOPOLOGY 54 select GENERIC_ATOMIC64 if CPU_V7M || CPU_V6 || !CPU_32v6K || !AEABI 55 select GENERIC_CLOCKEVENTS_BROADCAST if SMP 56 select GENERIC_IRQ_IPI if SMP 57 select GENERIC_CPU_AUTOPROBE 58 select GENERIC_EARLY_IOREMAP 59 select GENERIC_IDLE_POLL_SETUP 60 select GENERIC_IRQ_PROBE 61 select GENERIC_IRQ_SHOW 62 select GENERIC_IRQ_SHOW_LEVEL 63 select GENERIC_LIB_DEVMEM_IS_ALLOWED 64 select GENERIC_PCI_IOMAP 65 select GENERIC_SCHED_CLOCK 66 select GENERIC_SMP_IDLE_THREAD 67 select HANDLE_DOMAIN_IRQ 68 select HARDIRQS_SW_RESEND 69 select HAVE_ARCH_AUDITSYSCALL if AEABI && !OABI_COMPAT 70 select HAVE_ARCH_BITREVERSE if (CPU_32v7M || CPU_32v7) && !CPU_32v6 71 select HAVE_ARCH_JUMP_LABEL if !XIP_KERNEL && !CPU_ENDIAN_BE32 && MMU 72 select HAVE_ARCH_KGDB if !CPU_ENDIAN_BE32 && MMU 73 select HAVE_ARCH_KASAN if MMU && !XIP_KERNEL 74 select HAVE_ARCH_MMAP_RND_BITS if MMU 75 select HAVE_ARCH_PFN_VALID 76 select HAVE_ARCH_SECCOMP 77 select HAVE_ARCH_SECCOMP_FILTER if AEABI && !OABI_COMPAT 78 select HAVE_ARCH_THREAD_STRUCT_WHITELIST 79 select HAVE_ARCH_TRACEHOOK 80 select HAVE_ARCH_TRANSPARENT_HUGEPAGE if ARM_LPAE 81 select HAVE_ARM_SMCCC if CPU_V7 82 select HAVE_EBPF_JIT if !CPU_ENDIAN_BE32 83 select HAVE_CONTEXT_TRACKING 84 select HAVE_C_RECORDMCOUNT 85 select HAVE_DEBUG_KMEMLEAK if !XIP_KERNEL 86 select HAVE_DMA_CONTIGUOUS if MMU 87 select HAVE_DYNAMIC_FTRACE if !XIP_KERNEL && !CPU_ENDIAN_BE32 && MMU 88 select HAVE_DYNAMIC_FTRACE_WITH_REGS if HAVE_DYNAMIC_FTRACE 89 select HAVE_EFFICIENT_UNALIGNED_ACCESS if (CPU_V6 || CPU_V6K || CPU_V7) && MMU 90 select HAVE_EXIT_THREAD 91 select HAVE_FAST_GUP if ARM_LPAE 92 select HAVE_FTRACE_MCOUNT_RECORD if !XIP_KERNEL 93 select HAVE_FUNCTION_GRAPH_TRACER if !THUMB2_KERNEL && !CC_IS_CLANG 94 select HAVE_FUNCTION_TRACER if !XIP_KERNEL 95 select HAVE_GCC_PLUGINS 96 select HAVE_HW_BREAKPOINT if PERF_EVENTS && (CPU_V6 || CPU_V6K || CPU_V7) 97 select HAVE_IRQ_TIME_ACCOUNTING 98 select HAVE_KERNEL_GZIP 99 select HAVE_KERNEL_LZ4 100 select HAVE_KERNEL_LZMA 101 select HAVE_KERNEL_LZO 102 select HAVE_KERNEL_XZ 103 select HAVE_KPROBES if !XIP_KERNEL && !CPU_ENDIAN_BE32 && !CPU_V7M 104 select HAVE_KRETPROBES if HAVE_KPROBES 105 select HAVE_MOD_ARCH_SPECIFIC 106 select HAVE_NMI 107 select HAVE_OPTPROBES if !THUMB2_KERNEL 108 select HAVE_PERF_EVENTS 109 select HAVE_PERF_REGS 110 select HAVE_PERF_USER_STACK_DUMP 111 select MMU_GATHER_RCU_TABLE_FREE if SMP && ARM_LPAE 112 select HAVE_REGS_AND_STACK_ACCESS_API 113 select HAVE_RSEQ 114 select HAVE_STACKPROTECTOR 115 select HAVE_SYSCALL_TRACEPOINTS 116 select HAVE_UID16 117 select HAVE_VIRT_CPU_ACCOUNTING_GEN 118 select IRQ_FORCED_THREADING 119 select MODULES_USE_ELF_REL 120 select NEED_DMA_MAP_STATE 121 select OF_EARLY_FLATTREE if OF 122 select OLD_SIGACTION 123 select OLD_SIGSUSPEND3 124 select PCI_SYSCALL if PCI 125 select PERF_USE_VMALLOC 126 select RTC_LIB 127 select SYS_SUPPORTS_APM_EMULATION 128 select TRACE_IRQFLAGS_SUPPORT if !CPU_V7M 129 # Above selects are sorted alphabetically; please add new ones 130 # according to that. Thanks. 131 help 132 The ARM series is a line of low-power-consumption RISC chip designs 133 licensed by ARM Ltd and targeted at embedded applications and 134 handhelds such as the Compaq IPAQ. ARM-based PCs are no longer 135 manufactured, but legacy ARM-based PC hardware remains popular in 136 Europe. There is an ARM Linux project with a web page at 137 <http://www.arm.linux.org.uk/>. 138 139config ARM_HAS_SG_CHAIN 140 bool 141 142config ARM_DMA_USE_IOMMU 143 bool 144 select ARM_HAS_SG_CHAIN 145 select NEED_SG_DMA_LENGTH 146 147if ARM_DMA_USE_IOMMU 148 149config ARM_DMA_IOMMU_ALIGNMENT 150 int "Maximum PAGE_SIZE order of alignment for DMA IOMMU buffers" 151 range 4 9 152 default 8 153 help 154 DMA mapping framework by default aligns all buffers to the smallest 155 PAGE_SIZE order which is greater than or equal to the requested buffer 156 size. This works well for buffers up to a few hundreds kilobytes, but 157 for larger buffers it just a waste of address space. Drivers which has 158 relatively small addressing window (like 64Mib) might run out of 159 virtual space with just a few allocations. 160 161 With this parameter you can specify the maximum PAGE_SIZE order for 162 DMA IOMMU buffers. Larger buffers will be aligned only to this 163 specified order. The order is expressed as a power of two multiplied 164 by the PAGE_SIZE. 165 166endif 167 168config SYS_SUPPORTS_APM_EMULATION 169 bool 170 171config HAVE_TCM 172 bool 173 select GENERIC_ALLOCATOR 174 175config HAVE_PROC_CPU 176 bool 177 178config NO_IOPORT_MAP 179 bool 180 181config SBUS 182 bool 183 184config STACKTRACE_SUPPORT 185 bool 186 default y 187 188config LOCKDEP_SUPPORT 189 bool 190 default y 191 192config ARCH_HAS_ILOG2_U32 193 bool 194 195config ARCH_HAS_ILOG2_U64 196 bool 197 198config ARCH_HAS_BANDGAP 199 bool 200 201config FIX_EARLYCON_MEM 202 def_bool y if MMU 203 204config GENERIC_HWEIGHT 205 bool 206 default y 207 208config GENERIC_CALIBRATE_DELAY 209 bool 210 default y 211 212config ARCH_MAY_HAVE_PC_FDC 213 bool 214 215config ARCH_SUPPORTS_UPROBES 216 def_bool y 217 218config ARCH_HAS_DMA_SET_COHERENT_MASK 219 bool 220 221config GENERIC_ISA_DMA 222 bool 223 224config FIQ 225 bool 226 227config NEED_RET_TO_USER 228 bool 229 230config ARCH_MTD_XIP 231 bool 232 233config ARM_PATCH_PHYS_VIRT 234 bool "Patch physical to virtual translations at runtime" if EMBEDDED 235 default y 236 depends on !XIP_KERNEL && MMU 237 help 238 Patch phys-to-virt and virt-to-phys translation functions at 239 boot and module load time according to the position of the 240 kernel in system memory. 241 242 This can only be used with non-XIP MMU kernels where the base 243 of physical memory is at a 2 MiB boundary. 244 245 Only disable this option if you know that you do not require 246 this feature (eg, building a kernel for a single machine) and 247 you need to shrink the kernel to the minimal size. 248 249config NEED_MACH_IO_H 250 bool 251 help 252 Select this when mach/io.h is required to provide special 253 definitions for this platform. The need for mach/io.h should 254 be avoided when possible. 255 256config NEED_MACH_MEMORY_H 257 bool 258 help 259 Select this when mach/memory.h is required to provide special 260 definitions for this platform. The need for mach/memory.h should 261 be avoided when possible. 262 263config PHYS_OFFSET 264 hex "Physical address of main memory" if MMU 265 depends on !ARM_PATCH_PHYS_VIRT 266 default DRAM_BASE if !MMU 267 default 0x00000000 if ARCH_FOOTBRIDGE 268 default 0x10000000 if ARCH_OMAP1 || ARCH_RPC 269 default 0x20000000 if ARCH_S5PV210 270 default 0xc0000000 if ARCH_SA1100 271 help 272 Please provide the physical address corresponding to the 273 location of main memory in your system. 274 275config GENERIC_BUG 276 def_bool y 277 depends on BUG 278 279config PGTABLE_LEVELS 280 int 281 default 3 if ARM_LPAE 282 default 2 283 284menu "System Type" 285 286config MMU 287 bool "MMU-based Paged Memory Management Support" 288 default y 289 help 290 Select if you want MMU-based virtualised addressing space 291 support by paged memory management. If unsure, say 'Y'. 292 293config ARCH_MMAP_RND_BITS_MIN 294 default 8 295 296config ARCH_MMAP_RND_BITS_MAX 297 default 14 if PAGE_OFFSET=0x40000000 298 default 15 if PAGE_OFFSET=0x80000000 299 default 16 300 301# 302# The "ARM system type" choice list is ordered alphabetically by option 303# text. Please add new entries in the option alphabetic order. 304# 305choice 306 prompt "ARM system type" 307 default ARM_SINGLE_ARMV7M if !MMU 308 default ARCH_MULTIPLATFORM if MMU 309 310config ARCH_MULTIPLATFORM 311 bool "Allow multiple platforms to be selected" 312 depends on MMU 313 select ARCH_FLATMEM_ENABLE 314 select ARCH_SPARSEMEM_ENABLE 315 select ARCH_SELECT_MEMORY_MODEL 316 select ARM_HAS_SG_CHAIN 317 select ARM_PATCH_PHYS_VIRT 318 select AUTO_ZRELADDR 319 select TIMER_OF 320 select COMMON_CLK 321 select GENERIC_IRQ_MULTI_HANDLER 322 select HAVE_PCI 323 select PCI_DOMAINS_GENERIC if PCI 324 select SPARSE_IRQ 325 select USE_OF 326 327config ARM_SINGLE_ARMV7M 328 bool "ARMv7-M based platforms (Cortex-M0/M3/M4)" 329 depends on !MMU 330 select ARM_NVIC 331 select AUTO_ZRELADDR 332 select TIMER_OF 333 select COMMON_CLK 334 select CPU_V7M 335 select NO_IOPORT_MAP 336 select SPARSE_IRQ 337 select USE_OF 338 339config ARCH_EP93XX 340 bool "EP93xx-based" 341 select ARCH_SPARSEMEM_ENABLE 342 select ARM_AMBA 343 imply ARM_PATCH_PHYS_VIRT 344 select ARM_VIC 345 select GENERIC_IRQ_MULTI_HANDLER 346 select AUTO_ZRELADDR 347 select CLKSRC_MMIO 348 select CPU_ARM920T 349 select GPIOLIB 350 select HAVE_LEGACY_CLK 351 help 352 This enables support for the Cirrus EP93xx series of CPUs. 353 354config ARCH_FOOTBRIDGE 355 bool "FootBridge" 356 select CPU_SA110 357 select FOOTBRIDGE 358 select NEED_MACH_IO_H if !MMU 359 select NEED_MACH_MEMORY_H 360 help 361 Support for systems based on the DC21285 companion chip 362 ("FootBridge"), such as the Simtec CATS and the Rebel NetWinder. 363 364config ARCH_IOP32X 365 bool "IOP32x-based" 366 depends on MMU 367 select CPU_XSCALE 368 select GPIO_IOP 369 select GPIOLIB 370 select NEED_RET_TO_USER 371 select FORCE_PCI 372 select PLAT_IOP 373 help 374 Support for Intel's 80219 and IOP32X (XScale) family of 375 processors. 376 377config ARCH_IXP4XX 378 bool "IXP4xx-based" 379 depends on MMU 380 select ARCH_HAS_DMA_SET_COHERENT_MASK 381 select ARCH_SUPPORTS_BIG_ENDIAN 382 select CPU_XSCALE 383 select DMABOUNCE if PCI 384 select GENERIC_IRQ_MULTI_HANDLER 385 select GPIO_IXP4XX 386 select GPIOLIB 387 select HAVE_PCI 388 select IXP4XX_IRQ 389 select IXP4XX_TIMER 390 # With the new PCI driver this is not needed 391 select NEED_MACH_IO_H if IXP4XX_PCI_LEGACY 392 select USB_EHCI_BIG_ENDIAN_DESC 393 select USB_EHCI_BIG_ENDIAN_MMIO 394 help 395 Support for Intel's IXP4XX (XScale) family of processors. 396 397config ARCH_DOVE 398 bool "Marvell Dove" 399 select CPU_PJ4 400 select GENERIC_IRQ_MULTI_HANDLER 401 select GPIOLIB 402 select HAVE_PCI 403 select MVEBU_MBUS 404 select PINCTRL 405 select PINCTRL_DOVE 406 select PLAT_ORION_LEGACY 407 select SPARSE_IRQ 408 select PM_GENERIC_DOMAINS if PM 409 help 410 Support for the Marvell Dove SoC 88AP510 411 412config ARCH_PXA 413 bool "PXA2xx/PXA3xx-based" 414 depends on MMU 415 select ARCH_MTD_XIP 416 select ARM_CPU_SUSPEND if PM 417 select AUTO_ZRELADDR 418 select COMMON_CLK 419 select CLKSRC_PXA 420 select CLKSRC_MMIO 421 select TIMER_OF 422 select CPU_XSCALE if !CPU_XSC3 423 select GENERIC_IRQ_MULTI_HANDLER 424 select GPIO_PXA 425 select GPIOLIB 426 select IRQ_DOMAIN 427 select PLAT_PXA 428 select SPARSE_IRQ 429 help 430 Support for Intel/Marvell's PXA2xx/PXA3xx processor line. 431 432config ARCH_RPC 433 bool "RiscPC" 434 depends on MMU 435 select ARCH_ACORN 436 select ARCH_MAY_HAVE_PC_FDC 437 select ARCH_SPARSEMEM_ENABLE 438 select ARM_HAS_SG_CHAIN 439 select CPU_SA110 440 select FIQ 441 select HAVE_PATA_PLATFORM 442 select ISA_DMA_API 443 select LEGACY_TIMER_TICK 444 select NEED_MACH_IO_H 445 select NEED_MACH_MEMORY_H 446 select NO_IOPORT_MAP 447 help 448 On the Acorn Risc-PC, Linux can support the internal IDE disk and 449 CD-ROM interface, serial and parallel port, and the floppy drive. 450 451config ARCH_SA1100 452 bool "SA1100-based" 453 select ARCH_MTD_XIP 454 select ARCH_SPARSEMEM_ENABLE 455 select CLKSRC_MMIO 456 select CLKSRC_PXA 457 select TIMER_OF if OF 458 select COMMON_CLK 459 select CPU_FREQ 460 select CPU_SA1100 461 select GENERIC_IRQ_MULTI_HANDLER 462 select GPIOLIB 463 select IRQ_DOMAIN 464 select ISA 465 select NEED_MACH_MEMORY_H 466 select SPARSE_IRQ 467 help 468 Support for StrongARM 11x0 based boards. 469 470config ARCH_S3C24XX 471 bool "Samsung S3C24XX SoCs" 472 select ATAGS 473 select CLKSRC_SAMSUNG_PWM 474 select GPIO_SAMSUNG 475 select GPIOLIB 476 select GENERIC_IRQ_MULTI_HANDLER 477 select HAVE_S3C2410_I2C if I2C 478 select HAVE_S3C_RTC if RTC_CLASS 479 select NEED_MACH_IO_H 480 select S3C2410_WATCHDOG 481 select SAMSUNG_ATAGS 482 select USE_OF 483 select WATCHDOG 484 help 485 Samsung S3C2410, S3C2412, S3C2413, S3C2416, S3C2440, S3C2442, S3C2443 486 and S3C2450 SoCs based systems, such as the Simtec Electronics BAST 487 (<http://www.simtec.co.uk/products/EB110ITX/>), the IPAQ 1940 or the 488 Samsung SMDK2410 development board (and derivatives). 489 490config ARCH_OMAP1 491 bool "TI OMAP1" 492 depends on MMU 493 select ARCH_OMAP 494 select CLKSRC_MMIO 495 select GENERIC_IRQ_CHIP 496 select GENERIC_IRQ_MULTI_HANDLER 497 select GPIOLIB 498 select HAVE_LEGACY_CLK 499 select IRQ_DOMAIN 500 select NEED_MACH_IO_H if PCCARD 501 select NEED_MACH_MEMORY_H 502 select SPARSE_IRQ 503 help 504 Support for older TI OMAP1 (omap7xx, omap15xx or omap16xx) 505 506endchoice 507 508menu "Multiple platform selection" 509 depends on ARCH_MULTIPLATFORM 510 511comment "CPU Core family selection" 512 513config ARCH_MULTI_V4 514 bool "ARMv4 based platforms (FA526)" 515 depends on !ARCH_MULTI_V6_V7 516 select ARCH_MULTI_V4_V5 517 select CPU_FA526 518 519config ARCH_MULTI_V4T 520 bool "ARMv4T based platforms (ARM720T, ARM920T, ...)" 521 depends on !ARCH_MULTI_V6_V7 522 select ARCH_MULTI_V4_V5 523 select CPU_ARM920T if !(CPU_ARM7TDMI || CPU_ARM720T || \ 524 CPU_ARM740T || CPU_ARM9TDMI || CPU_ARM922T || \ 525 CPU_ARM925T || CPU_ARM940T) 526 527config ARCH_MULTI_V5 528 bool "ARMv5 based platforms (ARM926T, XSCALE, PJ1, ...)" 529 depends on !ARCH_MULTI_V6_V7 530 select ARCH_MULTI_V4_V5 531 select CPU_ARM926T if !(CPU_ARM946E || CPU_ARM1020 || \ 532 CPU_ARM1020E || CPU_ARM1022 || CPU_ARM1026 || \ 533 CPU_XSCALE || CPU_XSC3 || CPU_MOHAWK || CPU_FEROCEON) 534 535config ARCH_MULTI_V4_V5 536 bool 537 538config ARCH_MULTI_V6 539 bool "ARMv6 based platforms (ARM11)" 540 select ARCH_MULTI_V6_V7 541 select CPU_V6K 542 543config ARCH_MULTI_V7 544 bool "ARMv7 based platforms (Cortex-A, PJ4, Scorpion, Krait)" 545 default y 546 select ARCH_MULTI_V6_V7 547 select CPU_V7 548 select HAVE_SMP 549 550config ARCH_MULTI_V6_V7 551 bool 552 select MIGHT_HAVE_CACHE_L2X0 553 554config ARCH_MULTI_CPU_AUTO 555 def_bool !(ARCH_MULTI_V4 || ARCH_MULTI_V4T || ARCH_MULTI_V6_V7) 556 select ARCH_MULTI_V5 557 558endmenu 559 560config ARCH_VIRT 561 bool "Dummy Virtual Machine" 562 depends on ARCH_MULTI_V7 563 select ARM_AMBA 564 select ARM_GIC 565 select ARM_GIC_V2M if PCI 566 select ARM_GIC_V3 567 select ARM_GIC_V3_ITS if PCI 568 select ARM_PSCI 569 select HAVE_ARM_ARCH_TIMER 570 select ARCH_SUPPORTS_BIG_ENDIAN 571 572# 573# This is sorted alphabetically by mach-* pathname. However, plat-* 574# Kconfigs may be included either alphabetically (according to the 575# plat- suffix) or along side the corresponding mach-* source. 576# 577source "arch/arm/mach-actions/Kconfig" 578 579source "arch/arm/mach-alpine/Kconfig" 580 581source "arch/arm/mach-artpec/Kconfig" 582 583source "arch/arm/mach-asm9260/Kconfig" 584 585source "arch/arm/mach-aspeed/Kconfig" 586 587source "arch/arm/mach-at91/Kconfig" 588 589source "arch/arm/mach-axxia/Kconfig" 590 591source "arch/arm/mach-bcm/Kconfig" 592 593source "arch/arm/mach-berlin/Kconfig" 594 595source "arch/arm/mach-clps711x/Kconfig" 596 597source "arch/arm/mach-cns3xxx/Kconfig" 598 599source "arch/arm/mach-davinci/Kconfig" 600 601source "arch/arm/mach-digicolor/Kconfig" 602 603source "arch/arm/mach-dove/Kconfig" 604 605source "arch/arm/mach-ep93xx/Kconfig" 606 607source "arch/arm/mach-exynos/Kconfig" 608 609source "arch/arm/mach-footbridge/Kconfig" 610 611source "arch/arm/mach-gemini/Kconfig" 612 613source "arch/arm/mach-highbank/Kconfig" 614 615source "arch/arm/mach-hisi/Kconfig" 616 617source "arch/arm/mach-imx/Kconfig" 618 619source "arch/arm/mach-integrator/Kconfig" 620 621source "arch/arm/mach-iop32x/Kconfig" 622 623source "arch/arm/mach-ixp4xx/Kconfig" 624 625source "arch/arm/mach-keystone/Kconfig" 626 627source "arch/arm/mach-lpc32xx/Kconfig" 628 629source "arch/arm/mach-mediatek/Kconfig" 630 631source "arch/arm/mach-meson/Kconfig" 632 633source "arch/arm/mach-milbeaut/Kconfig" 634 635source "arch/arm/mach-mmp/Kconfig" 636 637source "arch/arm/mach-moxart/Kconfig" 638 639source "arch/arm/mach-mstar/Kconfig" 640 641source "arch/arm/mach-mv78xx0/Kconfig" 642 643source "arch/arm/mach-mvebu/Kconfig" 644 645source "arch/arm/mach-mxs/Kconfig" 646 647source "arch/arm/mach-nomadik/Kconfig" 648 649source "arch/arm/mach-npcm/Kconfig" 650 651source "arch/arm/mach-nspire/Kconfig" 652 653source "arch/arm/plat-omap/Kconfig" 654 655source "arch/arm/mach-omap1/Kconfig" 656 657source "arch/arm/mach-omap2/Kconfig" 658 659source "arch/arm/mach-orion5x/Kconfig" 660 661source "arch/arm/mach-oxnas/Kconfig" 662 663source "arch/arm/mach-pxa/Kconfig" 664source "arch/arm/plat-pxa/Kconfig" 665 666source "arch/arm/mach-qcom/Kconfig" 667 668source "arch/arm/mach-rda/Kconfig" 669 670source "arch/arm/mach-realtek/Kconfig" 671 672source "arch/arm/mach-realview/Kconfig" 673 674source "arch/arm/mach-rockchip/Kconfig" 675 676source "arch/arm/mach-s3c/Kconfig" 677 678source "arch/arm/mach-s5pv210/Kconfig" 679 680source "arch/arm/mach-sa1100/Kconfig" 681 682source "arch/arm/mach-shmobile/Kconfig" 683 684source "arch/arm/mach-socfpga/Kconfig" 685 686source "arch/arm/mach-spear/Kconfig" 687 688source "arch/arm/mach-sti/Kconfig" 689 690source "arch/arm/mach-stm32/Kconfig" 691 692source "arch/arm/mach-sunxi/Kconfig" 693 694source "arch/arm/mach-tegra/Kconfig" 695 696source "arch/arm/mach-uniphier/Kconfig" 697 698source "arch/arm/mach-ux500/Kconfig" 699 700source "arch/arm/mach-versatile/Kconfig" 701 702source "arch/arm/mach-vexpress/Kconfig" 703 704source "arch/arm/mach-vt8500/Kconfig" 705 706source "arch/arm/mach-zynq/Kconfig" 707 708# ARMv7-M architecture 709config ARCH_LPC18XX 710 bool "NXP LPC18xx/LPC43xx" 711 depends on ARM_SINGLE_ARMV7M 712 select ARCH_HAS_RESET_CONTROLLER 713 select ARM_AMBA 714 select CLKSRC_LPC32XX 715 select PINCTRL 716 help 717 Support for NXP's LPC18xx Cortex-M3 and LPC43xx Cortex-M4 718 high performance microcontrollers. 719 720config ARCH_MPS2 721 bool "ARM MPS2 platform" 722 depends on ARM_SINGLE_ARMV7M 723 select ARM_AMBA 724 select CLKSRC_MPS2 725 help 726 Support for Cortex-M Prototyping System (or V2M-MPS2) which comes 727 with a range of available cores like Cortex-M3/M4/M7. 728 729 Please, note that depends which Application Note is used memory map 730 for the platform may vary, so adjustment of RAM base might be needed. 731 732# Definitions to make life easier 733config ARCH_ACORN 734 bool 735 736config PLAT_IOP 737 bool 738 739config PLAT_ORION 740 bool 741 select CLKSRC_MMIO 742 select COMMON_CLK 743 select GENERIC_IRQ_CHIP 744 select IRQ_DOMAIN 745 746config PLAT_ORION_LEGACY 747 bool 748 select PLAT_ORION 749 750config PLAT_PXA 751 bool 752 753config PLAT_VERSATILE 754 bool 755 756source "arch/arm/mm/Kconfig" 757 758config IWMMXT 759 bool "Enable iWMMXt support" 760 depends on CPU_XSCALE || CPU_XSC3 || CPU_MOHAWK || CPU_PJ4 || CPU_PJ4B 761 default y if PXA27x || PXA3xx || ARCH_MMP || CPU_PJ4 || CPU_PJ4B 762 help 763 Enable support for iWMMXt context switching at run time if 764 running on a CPU that supports it. 765 766if !MMU 767source "arch/arm/Kconfig-nommu" 768endif 769 770config PJ4B_ERRATA_4742 771 bool "PJ4B Errata 4742: IDLE Wake Up Commands can Cause the CPU Core to Cease Operation" 772 depends on CPU_PJ4B && MACH_ARMADA_370 773 default y 774 help 775 When coming out of either a Wait for Interrupt (WFI) or a Wait for 776 Event (WFE) IDLE states, a specific timing sensitivity exists between 777 the retiring WFI/WFE instructions and the newly issued subsequent 778 instructions. This sensitivity can result in a CPU hang scenario. 779 Workaround: 780 The software must insert either a Data Synchronization Barrier (DSB) 781 or Data Memory Barrier (DMB) command immediately after the WFI/WFE 782 instruction 783 784config ARM_ERRATA_326103 785 bool "ARM errata: FSR write bit incorrect on a SWP to read-only memory" 786 depends on CPU_V6 787 help 788 Executing a SWP instruction to read-only memory does not set bit 11 789 of the FSR on the ARM 1136 prior to r1p0. This causes the kernel to 790 treat the access as a read, preventing a COW from occurring and 791 causing the faulting task to livelock. 792 793config ARM_ERRATA_411920 794 bool "ARM errata: Invalidation of the Instruction Cache operation can fail" 795 depends on CPU_V6 || CPU_V6K 796 help 797 Invalidation of the Instruction Cache operation can 798 fail. This erratum is present in 1136 (before r1p4), 1156 and 1176. 799 It does not affect the MPCore. This option enables the ARM Ltd. 800 recommended workaround. 801 802config ARM_ERRATA_430973 803 bool "ARM errata: Stale prediction on replaced interworking branch" 804 depends on CPU_V7 805 help 806 This option enables the workaround for the 430973 Cortex-A8 807 r1p* erratum. If a code sequence containing an ARM/Thumb 808 interworking branch is replaced with another code sequence at the 809 same virtual address, whether due to self-modifying code or virtual 810 to physical address re-mapping, Cortex-A8 does not recover from the 811 stale interworking branch prediction. This results in Cortex-A8 812 executing the new code sequence in the incorrect ARM or Thumb state. 813 The workaround enables the BTB/BTAC operations by setting ACTLR.IBE 814 and also flushes the branch target cache at every context switch. 815 Note that setting specific bits in the ACTLR register may not be 816 available in non-secure mode. 817 818config ARM_ERRATA_458693 819 bool "ARM errata: Processor deadlock when a false hazard is created" 820 depends on CPU_V7 821 depends on !ARCH_MULTIPLATFORM 822 help 823 This option enables the workaround for the 458693 Cortex-A8 (r2p0) 824 erratum. For very specific sequences of memory operations, it is 825 possible for a hazard condition intended for a cache line to instead 826 be incorrectly associated with a different cache line. This false 827 hazard might then cause a processor deadlock. The workaround enables 828 the L1 caching of the NEON accesses and disables the PLD instruction 829 in the ACTLR register. Note that setting specific bits in the ACTLR 830 register may not be available in non-secure mode. 831 832config ARM_ERRATA_460075 833 bool "ARM errata: Data written to the L2 cache can be overwritten with stale data" 834 depends on CPU_V7 835 depends on !ARCH_MULTIPLATFORM 836 help 837 This option enables the workaround for the 460075 Cortex-A8 (r2p0) 838 erratum. Any asynchronous access to the L2 cache may encounter a 839 situation in which recent store transactions to the L2 cache are lost 840 and overwritten with stale memory contents from external memory. The 841 workaround disables the write-allocate mode for the L2 cache via the 842 ACTLR register. Note that setting specific bits in the ACTLR register 843 may not be available in non-secure mode. 844 845config ARM_ERRATA_742230 846 bool "ARM errata: DMB operation may be faulty" 847 depends on CPU_V7 && SMP 848 depends on !ARCH_MULTIPLATFORM 849 help 850 This option enables the workaround for the 742230 Cortex-A9 851 (r1p0..r2p2) erratum. Under rare circumstances, a DMB instruction 852 between two write operations may not ensure the correct visibility 853 ordering of the two writes. This workaround sets a specific bit in 854 the diagnostic register of the Cortex-A9 which causes the DMB 855 instruction to behave as a DSB, ensuring the correct behaviour of 856 the two writes. 857 858config ARM_ERRATA_742231 859 bool "ARM errata: Incorrect hazard handling in the SCU may lead to data corruption" 860 depends on CPU_V7 && SMP 861 depends on !ARCH_MULTIPLATFORM 862 help 863 This option enables the workaround for the 742231 Cortex-A9 864 (r2p0..r2p2) erratum. Under certain conditions, specific to the 865 Cortex-A9 MPCore micro-architecture, two CPUs working in SMP mode, 866 accessing some data located in the same cache line, may get corrupted 867 data due to bad handling of the address hazard when the line gets 868 replaced from one of the CPUs at the same time as another CPU is 869 accessing it. This workaround sets specific bits in the diagnostic 870 register of the Cortex-A9 which reduces the linefill issuing 871 capabilities of the processor. 872 873config ARM_ERRATA_643719 874 bool "ARM errata: LoUIS bit field in CLIDR register is incorrect" 875 depends on CPU_V7 && SMP 876 default y 877 help 878 This option enables the workaround for the 643719 Cortex-A9 (prior to 879 r1p0) erratum. On affected cores the LoUIS bit field of the CLIDR 880 register returns zero when it should return one. The workaround 881 corrects this value, ensuring cache maintenance operations which use 882 it behave as intended and avoiding data corruption. 883 884config ARM_ERRATA_720789 885 bool "ARM errata: TLBIASIDIS and TLBIMVAIS operations can broadcast a faulty ASID" 886 depends on CPU_V7 887 help 888 This option enables the workaround for the 720789 Cortex-A9 (prior to 889 r2p0) erratum. A faulty ASID can be sent to the other CPUs for the 890 broadcasted CP15 TLB maintenance operations TLBIASIDIS and TLBIMVAIS. 891 As a consequence of this erratum, some TLB entries which should be 892 invalidated are not, resulting in an incoherency in the system page 893 tables. The workaround changes the TLB flushing routines to invalidate 894 entries regardless of the ASID. 895 896config ARM_ERRATA_743622 897 bool "ARM errata: Faulty hazard checking in the Store Buffer may lead to data corruption" 898 depends on CPU_V7 899 depends on !ARCH_MULTIPLATFORM 900 help 901 This option enables the workaround for the 743622 Cortex-A9 902 (r2p*) erratum. Under very rare conditions, a faulty 903 optimisation in the Cortex-A9 Store Buffer may lead to data 904 corruption. This workaround sets a specific bit in the diagnostic 905 register of the Cortex-A9 which disables the Store Buffer 906 optimisation, preventing the defect from occurring. This has no 907 visible impact on the overall performance or power consumption of the 908 processor. 909 910config ARM_ERRATA_751472 911 bool "ARM errata: Interrupted ICIALLUIS may prevent completion of broadcasted operation" 912 depends on CPU_V7 913 depends on !ARCH_MULTIPLATFORM 914 help 915 This option enables the workaround for the 751472 Cortex-A9 (prior 916 to r3p0) erratum. An interrupted ICIALLUIS operation may prevent the 917 completion of a following broadcasted operation if the second 918 operation is received by a CPU before the ICIALLUIS has completed, 919 potentially leading to corrupted entries in the cache or TLB. 920 921config ARM_ERRATA_754322 922 bool "ARM errata: possible faulty MMU translations following an ASID switch" 923 depends on CPU_V7 924 help 925 This option enables the workaround for the 754322 Cortex-A9 (r2p*, 926 r3p*) erratum. A speculative memory access may cause a page table walk 927 which starts prior to an ASID switch but completes afterwards. This 928 can populate the micro-TLB with a stale entry which may be hit with 929 the new ASID. This workaround places two dsb instructions in the mm 930 switching code so that no page table walks can cross the ASID switch. 931 932config ARM_ERRATA_754327 933 bool "ARM errata: no automatic Store Buffer drain" 934 depends on CPU_V7 && SMP 935 help 936 This option enables the workaround for the 754327 Cortex-A9 (prior to 937 r2p0) erratum. The Store Buffer does not have any automatic draining 938 mechanism and therefore a livelock may occur if an external agent 939 continuously polls a memory location waiting to observe an update. 940 This workaround defines cpu_relax() as smp_mb(), preventing correctly 941 written polling loops from denying visibility of updates to memory. 942 943config ARM_ERRATA_364296 944 bool "ARM errata: Possible cache data corruption with hit-under-miss enabled" 945 depends on CPU_V6 946 help 947 This options enables the workaround for the 364296 ARM1136 948 r0p2 erratum (possible cache data corruption with 949 hit-under-miss enabled). It sets the undocumented bit 31 in 950 the auxiliary control register and the FI bit in the control 951 register, thus disabling hit-under-miss without putting the 952 processor into full low interrupt latency mode. ARM11MPCore 953 is not affected. 954 955config ARM_ERRATA_764369 956 bool "ARM errata: Data cache line maintenance operation by MVA may not succeed" 957 depends on CPU_V7 && SMP 958 help 959 This option enables the workaround for erratum 764369 960 affecting Cortex-A9 MPCore with two or more processors (all 961 current revisions). Under certain timing circumstances, a data 962 cache line maintenance operation by MVA targeting an Inner 963 Shareable memory region may fail to proceed up to either the 964 Point of Coherency or to the Point of Unification of the 965 system. This workaround adds a DSB instruction before the 966 relevant cache maintenance functions and sets a specific bit 967 in the diagnostic control register of the SCU. 968 969config ARM_ERRATA_775420 970 bool "ARM errata: A data cache maintenance operation which aborts, might lead to deadlock" 971 depends on CPU_V7 972 help 973 This option enables the workaround for the 775420 Cortex-A9 (r2p2, 974 r2p6,r2p8,r2p10,r3p0) erratum. In case a data cache maintenance 975 operation aborts with MMU exception, it might cause the processor 976 to deadlock. This workaround puts DSB before executing ISB if 977 an abort may occur on cache maintenance. 978 979config ARM_ERRATA_798181 980 bool "ARM errata: TLBI/DSB failure on Cortex-A15" 981 depends on CPU_V7 && SMP 982 help 983 On Cortex-A15 (r0p0..r3p2) the TLBI*IS/DSB operations are not 984 adequately shooting down all use of the old entries. This 985 option enables the Linux kernel workaround for this erratum 986 which sends an IPI to the CPUs that are running the same ASID 987 as the one being invalidated. 988 989config ARM_ERRATA_773022 990 bool "ARM errata: incorrect instructions may be executed from loop buffer" 991 depends on CPU_V7 992 help 993 This option enables the workaround for the 773022 Cortex-A15 994 (up to r0p4) erratum. In certain rare sequences of code, the 995 loop buffer may deliver incorrect instructions. This 996 workaround disables the loop buffer to avoid the erratum. 997 998config ARM_ERRATA_818325_852422 999 bool "ARM errata: A12: some seqs of opposed cond code instrs => deadlock or corruption" 1000 depends on CPU_V7 1001 help 1002 This option enables the workaround for: 1003 - Cortex-A12 818325: Execution of an UNPREDICTABLE STR or STM 1004 instruction might deadlock. Fixed in r0p1. 1005 - Cortex-A12 852422: Execution of a sequence of instructions might 1006 lead to either a data corruption or a CPU deadlock. Not fixed in 1007 any Cortex-A12 cores yet. 1008 This workaround for all both errata involves setting bit[12] of the 1009 Feature Register. This bit disables an optimisation applied to a 1010 sequence of 2 instructions that use opposing condition codes. 1011 1012config ARM_ERRATA_821420 1013 bool "ARM errata: A12: sequence of VMOV to core registers might lead to a dead lock" 1014 depends on CPU_V7 1015 help 1016 This option enables the workaround for the 821420 Cortex-A12 1017 (all revs) erratum. In very rare timing conditions, a sequence 1018 of VMOV to Core registers instructions, for which the second 1019 one is in the shadow of a branch or abort, can lead to a 1020 deadlock when the VMOV instructions are issued out-of-order. 1021 1022config ARM_ERRATA_825619 1023 bool "ARM errata: A12: DMB NSHST/ISHST mixed ... might cause deadlock" 1024 depends on CPU_V7 1025 help 1026 This option enables the workaround for the 825619 Cortex-A12 1027 (all revs) erratum. Within rare timing constraints, executing a 1028 DMB NSHST or DMB ISHST instruction followed by a mix of Cacheable 1029 and Device/Strongly-Ordered loads and stores might cause deadlock 1030 1031config ARM_ERRATA_857271 1032 bool "ARM errata: A12: CPU might deadlock under some very rare internal conditions" 1033 depends on CPU_V7 1034 help 1035 This option enables the workaround for the 857271 Cortex-A12 1036 (all revs) erratum. Under very rare timing conditions, the CPU might 1037 hang. The workaround is expected to have a < 1% performance impact. 1038 1039config ARM_ERRATA_852421 1040 bool "ARM errata: A17: DMB ST might fail to create order between stores" 1041 depends on CPU_V7 1042 help 1043 This option enables the workaround for the 852421 Cortex-A17 1044 (r1p0, r1p1, r1p2) erratum. Under very rare timing conditions, 1045 execution of a DMB ST instruction might fail to properly order 1046 stores from GroupA and stores from GroupB. 1047 1048config ARM_ERRATA_852423 1049 bool "ARM errata: A17: some seqs of opposed cond code instrs => deadlock or corruption" 1050 depends on CPU_V7 1051 help 1052 This option enables the workaround for: 1053 - Cortex-A17 852423: Execution of a sequence of instructions might 1054 lead to either a data corruption or a CPU deadlock. Not fixed in 1055 any Cortex-A17 cores yet. 1056 This is identical to Cortex-A12 erratum 852422. It is a separate 1057 config option from the A12 erratum due to the way errata are checked 1058 for and handled. 1059 1060config ARM_ERRATA_857272 1061 bool "ARM errata: A17: CPU might deadlock under some very rare internal conditions" 1062 depends on CPU_V7 1063 help 1064 This option enables the workaround for the 857272 Cortex-A17 erratum. 1065 This erratum is not known to be fixed in any A17 revision. 1066 This is identical to Cortex-A12 erratum 857271. It is a separate 1067 config option from the A12 erratum due to the way errata are checked 1068 for and handled. 1069 1070endmenu 1071 1072source "arch/arm/common/Kconfig" 1073 1074menu "Bus support" 1075 1076config ISA 1077 bool 1078 help 1079 Find out whether you have ISA slots on your motherboard. ISA is the 1080 name of a bus system, i.e. the way the CPU talks to the other stuff 1081 inside your box. Other bus systems are PCI, EISA, MicroChannel 1082 (MCA) or VESA. ISA is an older system, now being displaced by PCI; 1083 newer boards don't support it. If you have ISA, say Y, otherwise N. 1084 1085# Select ISA DMA controller support 1086config ISA_DMA 1087 bool 1088 select ISA_DMA_API 1089 1090# Select ISA DMA interface 1091config ISA_DMA_API 1092 bool 1093 1094config PCI_NANOENGINE 1095 bool "BSE nanoEngine PCI support" 1096 depends on SA1100_NANOENGINE 1097 help 1098 Enable PCI on the BSE nanoEngine board. 1099 1100config ARM_ERRATA_814220 1101 bool "ARM errata: Cache maintenance by set/way operations can execute out of order" 1102 depends on CPU_V7 1103 help 1104 The v7 ARM states that all cache and branch predictor maintenance 1105 operations that do not specify an address execute, relative to 1106 each other, in program order. 1107 However, because of this erratum, an L2 set/way cache maintenance 1108 operation can overtake an L1 set/way cache maintenance operation. 1109 This ERRATA only affected the Cortex-A7 and present in r0p2, r0p3, 1110 r0p4, r0p5. 1111 1112endmenu 1113 1114menu "Kernel Features" 1115 1116config HAVE_SMP 1117 bool 1118 help 1119 This option should be selected by machines which have an SMP- 1120 capable CPU. 1121 1122 The only effect of this option is to make the SMP-related 1123 options available to the user for configuration. 1124 1125config SMP 1126 bool "Symmetric Multi-Processing" 1127 depends on CPU_V6K || CPU_V7 1128 depends on HAVE_SMP 1129 depends on MMU || ARM_MPU 1130 select IRQ_WORK 1131 help 1132 This enables support for systems with more than one CPU. If you have 1133 a system with only one CPU, say N. If you have a system with more 1134 than one CPU, say Y. 1135 1136 If you say N here, the kernel will run on uni- and multiprocessor 1137 machines, but will use only one CPU of a multiprocessor machine. If 1138 you say Y here, the kernel will run on many, but not all, 1139 uniprocessor machines. On a uniprocessor machine, the kernel 1140 will run faster if you say N here. 1141 1142 See also <file:Documentation/x86/i386/IO-APIC.rst>, 1143 <file:Documentation/admin-guide/lockup-watchdogs.rst> and the SMP-HOWTO available at 1144 <http://tldp.org/HOWTO/SMP-HOWTO.html>. 1145 1146 If you don't know what to do here, say N. 1147 1148config SMP_ON_UP 1149 bool "Allow booting SMP kernel on uniprocessor systems" 1150 depends on SMP && !XIP_KERNEL && MMU 1151 default y 1152 help 1153 SMP kernels contain instructions which fail on non-SMP processors. 1154 Enabling this option allows the kernel to modify itself to make 1155 these instructions safe. Disabling it allows about 1K of space 1156 savings. 1157 1158 If you don't know what to do here, say Y. 1159 1160config ARM_CPU_TOPOLOGY 1161 bool "Support cpu topology definition" 1162 depends on SMP && CPU_V7 1163 default y 1164 help 1165 Support ARM cpu topology definition. The MPIDR register defines 1166 affinity between processors which is then used to describe the cpu 1167 topology of an ARM System. 1168 1169config SCHED_MC 1170 bool "Multi-core scheduler support" 1171 depends on ARM_CPU_TOPOLOGY 1172 help 1173 Multi-core scheduler support improves the CPU scheduler's decision 1174 making when dealing with multi-core CPU chips at a cost of slightly 1175 increased overhead in some places. If unsure say N here. 1176 1177config SCHED_SMT 1178 bool "SMT scheduler support" 1179 depends on ARM_CPU_TOPOLOGY 1180 help 1181 Improves the CPU scheduler's decision making when dealing with 1182 MultiThreading at a cost of slightly increased overhead in some 1183 places. If unsure say N here. 1184 1185config HAVE_ARM_SCU 1186 bool 1187 help 1188 This option enables support for the ARM snoop control unit 1189 1190config HAVE_ARM_ARCH_TIMER 1191 bool "Architected timer support" 1192 depends on CPU_V7 1193 select ARM_ARCH_TIMER 1194 help 1195 This option enables support for the ARM architected timer 1196 1197config HAVE_ARM_TWD 1198 bool 1199 help 1200 This options enables support for the ARM timer and watchdog unit 1201 1202config MCPM 1203 bool "Multi-Cluster Power Management" 1204 depends on CPU_V7 && SMP 1205 help 1206 This option provides the common power management infrastructure 1207 for (multi-)cluster based systems, such as big.LITTLE based 1208 systems. 1209 1210config MCPM_QUAD_CLUSTER 1211 bool 1212 depends on MCPM 1213 help 1214 To avoid wasting resources unnecessarily, MCPM only supports up 1215 to 2 clusters by default. 1216 Platforms with 3 or 4 clusters that use MCPM must select this 1217 option to allow the additional clusters to be managed. 1218 1219config BIG_LITTLE 1220 bool "big.LITTLE support (Experimental)" 1221 depends on CPU_V7 && SMP 1222 select MCPM 1223 help 1224 This option enables support selections for the big.LITTLE 1225 system architecture. 1226 1227config BL_SWITCHER 1228 bool "big.LITTLE switcher support" 1229 depends on BIG_LITTLE && MCPM && HOTPLUG_CPU && ARM_GIC 1230 select CPU_PM 1231 help 1232 The big.LITTLE "switcher" provides the core functionality to 1233 transparently handle transition between a cluster of A15's 1234 and a cluster of A7's in a big.LITTLE system. 1235 1236config BL_SWITCHER_DUMMY_IF 1237 tristate "Simple big.LITTLE switcher user interface" 1238 depends on BL_SWITCHER && DEBUG_KERNEL 1239 help 1240 This is a simple and dummy char dev interface to control 1241 the big.LITTLE switcher core code. It is meant for 1242 debugging purposes only. 1243 1244choice 1245 prompt "Memory split" 1246 depends on MMU 1247 default VMSPLIT_3G 1248 help 1249 Select the desired split between kernel and user memory. 1250 1251 If you are not absolutely sure what you are doing, leave this 1252 option alone! 1253 1254 config VMSPLIT_3G 1255 bool "3G/1G user/kernel split" 1256 config VMSPLIT_3G_OPT 1257 depends on !ARM_LPAE 1258 bool "3G/1G user/kernel split (for full 1G low memory)" 1259 config VMSPLIT_2G 1260 bool "2G/2G user/kernel split" 1261 config VMSPLIT_1G 1262 bool "1G/3G user/kernel split" 1263endchoice 1264 1265config PAGE_OFFSET 1266 hex 1267 default PHYS_OFFSET if !MMU 1268 default 0x40000000 if VMSPLIT_1G 1269 default 0x80000000 if VMSPLIT_2G 1270 default 0xB0000000 if VMSPLIT_3G_OPT 1271 default 0xC0000000 1272 1273config KASAN_SHADOW_OFFSET 1274 hex 1275 depends on KASAN 1276 default 0x1f000000 if PAGE_OFFSET=0x40000000 1277 default 0x5f000000 if PAGE_OFFSET=0x80000000 1278 default 0x9f000000 if PAGE_OFFSET=0xC0000000 1279 default 0x8f000000 if PAGE_OFFSET=0xB0000000 1280 default 0xffffffff 1281 1282config NR_CPUS 1283 int "Maximum number of CPUs (2-32)" 1284 range 2 16 if DEBUG_KMAP_LOCAL 1285 range 2 32 if !DEBUG_KMAP_LOCAL 1286 depends on SMP 1287 default "4" 1288 help 1289 The maximum number of CPUs that the kernel can support. 1290 Up to 32 CPUs can be supported, or up to 16 if kmap_local() 1291 debugging is enabled, which uses half of the per-CPU fixmap 1292 slots as guard regions. 1293 1294config HOTPLUG_CPU 1295 bool "Support for hot-pluggable CPUs" 1296 depends on SMP 1297 select GENERIC_IRQ_MIGRATION 1298 help 1299 Say Y here to experiment with turning CPUs off and on. CPUs 1300 can be controlled through /sys/devices/system/cpu. 1301 1302config ARM_PSCI 1303 bool "Support for the ARM Power State Coordination Interface (PSCI)" 1304 depends on HAVE_ARM_SMCCC 1305 select ARM_PSCI_FW 1306 help 1307 Say Y here if you want Linux to communicate with system firmware 1308 implementing the PSCI specification for CPU-centric power 1309 management operations described in ARM document number ARM DEN 1310 0022A ("Power State Coordination Interface System Software on 1311 ARM processors"). 1312 1313# The GPIO number here must be sorted by descending number. In case of 1314# a multiplatform kernel, we just want the highest value required by the 1315# selected platforms. 1316config ARCH_NR_GPIO 1317 int 1318 default 2048 if ARCH_INTEL_SOCFPGA 1319 default 1024 if ARCH_BRCMSTB || ARCH_RENESAS || ARCH_TEGRA || \ 1320 ARCH_ZYNQ || ARCH_ASPEED 1321 default 512 if ARCH_EXYNOS || ARCH_KEYSTONE || SOC_OMAP5 || \ 1322 SOC_DRA7XX || ARCH_S3C24XX || ARCH_S3C64XX || ARCH_S5PV210 1323 default 416 if ARCH_SUNXI 1324 default 392 if ARCH_U8500 1325 default 352 if ARCH_VT8500 1326 default 288 if ARCH_ROCKCHIP 1327 default 264 if MACH_H4700 1328 default 0 1329 help 1330 Maximum number of GPIOs in the system. 1331 1332 If unsure, leave the default value. 1333 1334config HZ_FIXED 1335 int 1336 default 128 if SOC_AT91RM9200 1337 default 0 1338 1339choice 1340 depends on HZ_FIXED = 0 1341 prompt "Timer frequency" 1342 1343config HZ_100 1344 bool "100 Hz" 1345 1346config HZ_200 1347 bool "200 Hz" 1348 1349config HZ_250 1350 bool "250 Hz" 1351 1352config HZ_300 1353 bool "300 Hz" 1354 1355config HZ_500 1356 bool "500 Hz" 1357 1358config HZ_1000 1359 bool "1000 Hz" 1360 1361endchoice 1362 1363config HZ 1364 int 1365 default HZ_FIXED if HZ_FIXED != 0 1366 default 100 if HZ_100 1367 default 200 if HZ_200 1368 default 250 if HZ_250 1369 default 300 if HZ_300 1370 default 500 if HZ_500 1371 default 1000 1372 1373config SCHED_HRTICK 1374 def_bool HIGH_RES_TIMERS 1375 1376config THUMB2_KERNEL 1377 bool "Compile the kernel in Thumb-2 mode" if !CPU_THUMBONLY 1378 depends on (CPU_V7 || CPU_V7M) && !CPU_V6 && !CPU_V6K 1379 default y if CPU_THUMBONLY 1380 select ARM_UNWIND 1381 help 1382 By enabling this option, the kernel will be compiled in 1383 Thumb-2 mode. 1384 1385 If unsure, say N. 1386 1387config ARM_PATCH_IDIV 1388 bool "Runtime patch udiv/sdiv instructions into __aeabi_{u}idiv()" 1389 depends on CPU_32v7 && !XIP_KERNEL 1390 default y 1391 help 1392 The ARM compiler inserts calls to __aeabi_idiv() and 1393 __aeabi_uidiv() when it needs to perform division on signed 1394 and unsigned integers. Some v7 CPUs have support for the sdiv 1395 and udiv instructions that can be used to implement those 1396 functions. 1397 1398 Enabling this option allows the kernel to modify itself to 1399 replace the first two instructions of these library functions 1400 with the sdiv or udiv plus "bx lr" instructions when the CPU 1401 it is running on supports them. Typically this will be faster 1402 and less power intensive than running the original library 1403 code to do integer division. 1404 1405config AEABI 1406 bool "Use the ARM EABI to compile the kernel" if !CPU_V7 && \ 1407 !CPU_V7M && !CPU_V6 && !CPU_V6K && !CC_IS_CLANG 1408 default CPU_V7 || CPU_V7M || CPU_V6 || CPU_V6K || CC_IS_CLANG 1409 help 1410 This option allows for the kernel to be compiled using the latest 1411 ARM ABI (aka EABI). This is only useful if you are using a user 1412 space environment that is also compiled with EABI. 1413 1414 Since there are major incompatibilities between the legacy ABI and 1415 EABI, especially with regard to structure member alignment, this 1416 option also changes the kernel syscall calling convention to 1417 disambiguate both ABIs and allow for backward compatibility support 1418 (selected with CONFIG_OABI_COMPAT). 1419 1420 To use this you need GCC version 4.0.0 or later. 1421 1422config OABI_COMPAT 1423 bool "Allow old ABI binaries to run with this kernel (EXPERIMENTAL)" 1424 depends on AEABI && !THUMB2_KERNEL 1425 help 1426 This option preserves the old syscall interface along with the 1427 new (ARM EABI) one. It also provides a compatibility layer to 1428 intercept syscalls that have structure arguments which layout 1429 in memory differs between the legacy ABI and the new ARM EABI 1430 (only for non "thumb" binaries). This option adds a tiny 1431 overhead to all syscalls and produces a slightly larger kernel. 1432 1433 The seccomp filter system will not be available when this is 1434 selected, since there is no way yet to sensibly distinguish 1435 between calling conventions during filtering. 1436 1437 If you know you'll be using only pure EABI user space then you 1438 can say N here. If this option is not selected and you attempt 1439 to execute a legacy ABI binary then the result will be 1440 UNPREDICTABLE (in fact it can be predicted that it won't work 1441 at all). If in doubt say N. 1442 1443config ARCH_SELECT_MEMORY_MODEL 1444 bool 1445 1446config ARCH_FLATMEM_ENABLE 1447 bool 1448 1449config ARCH_SPARSEMEM_ENABLE 1450 bool 1451 select SPARSEMEM_STATIC if SPARSEMEM 1452 1453config HIGHMEM 1454 bool "High Memory Support" 1455 depends on MMU 1456 select KMAP_LOCAL 1457 help 1458 The address space of ARM processors is only 4 Gigabytes large 1459 and it has to accommodate user address space, kernel address 1460 space as well as some memory mapped IO. That means that, if you 1461 have a large amount of physical memory and/or IO, not all of the 1462 memory can be "permanently mapped" by the kernel. The physical 1463 memory that is not permanently mapped is called "high memory". 1464 1465 Depending on the selected kernel/user memory split, minimum 1466 vmalloc space and actual amount of RAM, you may not need this 1467 option which should result in a slightly faster kernel. 1468 1469 If unsure, say n. 1470 1471config HIGHPTE 1472 bool "Allocate 2nd-level pagetables from highmem" if EXPERT 1473 depends on HIGHMEM 1474 default y 1475 help 1476 The VM uses one page of physical memory for each page table. 1477 For systems with a lot of processes, this can use a lot of 1478 precious low memory, eventually leading to low memory being 1479 consumed by page tables. Setting this option will allow 1480 user-space 2nd level page tables to reside in high memory. 1481 1482config CPU_SW_DOMAIN_PAN 1483 bool "Enable use of CPU domains to implement privileged no-access" 1484 depends on MMU && !ARM_LPAE 1485 default y 1486 help 1487 Increase kernel security by ensuring that normal kernel accesses 1488 are unable to access userspace addresses. This can help prevent 1489 use-after-free bugs becoming an exploitable privilege escalation 1490 by ensuring that magic values (such as LIST_POISON) will always 1491 fault when dereferenced. 1492 1493 CPUs with low-vector mappings use a best-efforts implementation. 1494 Their lower 1MB needs to remain accessible for the vectors, but 1495 the remainder of userspace will become appropriately inaccessible. 1496 1497config HW_PERF_EVENTS 1498 def_bool y 1499 depends on ARM_PMU 1500 1501config ARCH_WANT_GENERAL_HUGETLB 1502 def_bool y 1503 1504config ARM_MODULE_PLTS 1505 bool "Use PLTs to allow module memory to spill over into vmalloc area" 1506 depends on MODULES 1507 default y 1508 help 1509 Allocate PLTs when loading modules so that jumps and calls whose 1510 targets are too far away for their relative offsets to be encoded 1511 in the instructions themselves can be bounced via veneers in the 1512 module's PLT. This allows modules to be allocated in the generic 1513 vmalloc area after the dedicated module memory area has been 1514 exhausted. The modules will use slightly more memory, but after 1515 rounding up to page size, the actual memory footprint is usually 1516 the same. 1517 1518 Disabling this is usually safe for small single-platform 1519 configurations. If unsure, say y. 1520 1521config FORCE_MAX_ZONEORDER 1522 int "Maximum zone order" 1523 default "12" if SOC_AM33XX 1524 default "9" if SA1111 1525 default "11" 1526 help 1527 The kernel memory allocator divides physically contiguous memory 1528 blocks into "zones", where each zone is a power of two number of 1529 pages. This option selects the largest power of two that the kernel 1530 keeps in the memory allocator. If you need to allocate very large 1531 blocks of physically contiguous memory, then you may need to 1532 increase this value. 1533 1534 This config option is actually maximum order plus one. For example, 1535 a value of 11 means that the largest free memory block is 2^10 pages. 1536 1537config ALIGNMENT_TRAP 1538 def_bool CPU_CP15_MMU 1539 select HAVE_PROC_CPU if PROC_FS 1540 help 1541 ARM processors cannot fetch/store information which is not 1542 naturally aligned on the bus, i.e., a 4 byte fetch must start at an 1543 address divisible by 4. On 32-bit ARM processors, these non-aligned 1544 fetch/store instructions will be emulated in software if you say 1545 here, which has a severe performance impact. This is necessary for 1546 correct operation of some network protocols. With an IP-only 1547 configuration it is safe to say N, otherwise say Y. 1548 1549config UACCESS_WITH_MEMCPY 1550 bool "Use kernel mem{cpy,set}() for {copy_to,clear}_user()" 1551 depends on MMU 1552 default y if CPU_FEROCEON 1553 help 1554 Implement faster copy_to_user and clear_user methods for CPU 1555 cores where a 8-word STM instruction give significantly higher 1556 memory write throughput than a sequence of individual 32bit stores. 1557 1558 A possible side effect is a slight increase in scheduling latency 1559 between threads sharing the same address space if they invoke 1560 such copy operations with large buffers. 1561 1562 However, if the CPU data cache is using a write-allocate mode, 1563 this option is unlikely to provide any performance gain. 1564 1565config PARAVIRT 1566 bool "Enable paravirtualization code" 1567 help 1568 This changes the kernel so it can modify itself when it is run 1569 under a hypervisor, potentially improving performance significantly 1570 over full virtualization. 1571 1572config PARAVIRT_TIME_ACCOUNTING 1573 bool "Paravirtual steal time accounting" 1574 select PARAVIRT 1575 help 1576 Select this option to enable fine granularity task steal time 1577 accounting. Time spent executing other tasks in parallel with 1578 the current vCPU is discounted from the vCPU power. To account for 1579 that, there can be a small performance impact. 1580 1581 If in doubt, say N here. 1582 1583config XEN_DOM0 1584 def_bool y 1585 depends on XEN 1586 1587config XEN 1588 bool "Xen guest support on ARM" 1589 depends on ARM && AEABI && OF 1590 depends on CPU_V7 && !CPU_V6 1591 depends on !GENERIC_ATOMIC64 1592 depends on MMU 1593 select ARCH_DMA_ADDR_T_64BIT 1594 select ARM_PSCI 1595 select SWIOTLB 1596 select SWIOTLB_XEN 1597 select PARAVIRT 1598 help 1599 Say Y if you want to run Linux in a Virtual Machine on Xen on ARM. 1600 1601config STACKPROTECTOR_PER_TASK 1602 bool "Use a unique stack canary value for each task" 1603 depends on GCC_PLUGINS && STACKPROTECTOR && SMP && !XIP_DEFLATED_DATA 1604 select GCC_PLUGIN_ARM_SSP_PER_TASK 1605 default y 1606 help 1607 Due to the fact that GCC uses an ordinary symbol reference from 1608 which to load the value of the stack canary, this value can only 1609 change at reboot time on SMP systems, and all tasks running in the 1610 kernel's address space are forced to use the same canary value for 1611 the entire duration that the system is up. 1612 1613 Enable this option to switch to a different method that uses a 1614 different canary value for each task. 1615 1616endmenu 1617 1618menu "Boot options" 1619 1620config USE_OF 1621 bool "Flattened Device Tree support" 1622 select IRQ_DOMAIN 1623 select OF 1624 help 1625 Include support for flattened device tree machine descriptions. 1626 1627config ATAGS 1628 bool "Support for the traditional ATAGS boot data passing" if USE_OF 1629 default y 1630 help 1631 This is the traditional way of passing data to the kernel at boot 1632 time. If you are solely relying on the flattened device tree (or 1633 the ARM_ATAG_DTB_COMPAT option) then you may unselect this option 1634 to remove ATAGS support from your kernel binary. If unsure, 1635 leave this to y. 1636 1637config DEPRECATED_PARAM_STRUCT 1638 bool "Provide old way to pass kernel parameters" 1639 depends on ATAGS 1640 help 1641 This was deprecated in 2001 and announced to live on for 5 years. 1642 Some old boot loaders still use this way. 1643 1644# Compressed boot loader in ROM. Yes, we really want to ask about 1645# TEXT and BSS so we preserve their values in the config files. 1646config ZBOOT_ROM_TEXT 1647 hex "Compressed ROM boot loader base address" 1648 default 0x0 1649 help 1650 The physical address at which the ROM-able zImage is to be 1651 placed in the target. Platforms which normally make use of 1652 ROM-able zImage formats normally set this to a suitable 1653 value in their defconfig file. 1654 1655 If ZBOOT_ROM is not enabled, this has no effect. 1656 1657config ZBOOT_ROM_BSS 1658 hex "Compressed ROM boot loader BSS address" 1659 default 0x0 1660 help 1661 The base address of an area of read/write memory in the target 1662 for the ROM-able zImage which must be available while the 1663 decompressor is running. It must be large enough to hold the 1664 entire decompressed kernel plus an additional 128 KiB. 1665 Platforms which normally make use of ROM-able zImage formats 1666 normally set this to a suitable value in their defconfig file. 1667 1668 If ZBOOT_ROM is not enabled, this has no effect. 1669 1670config ZBOOT_ROM 1671 bool "Compressed boot loader in ROM/flash" 1672 depends on ZBOOT_ROM_TEXT != ZBOOT_ROM_BSS 1673 depends on !ARM_APPENDED_DTB && !XIP_KERNEL && !AUTO_ZRELADDR 1674 help 1675 Say Y here if you intend to execute your compressed kernel image 1676 (zImage) directly from ROM or flash. If unsure, say N. 1677 1678config ARM_APPENDED_DTB 1679 bool "Use appended device tree blob to zImage (EXPERIMENTAL)" 1680 depends on OF 1681 help 1682 With this option, the boot code will look for a device tree binary 1683 (DTB) appended to zImage 1684 (e.g. cat zImage <filename>.dtb > zImage_w_dtb). 1685 1686 This is meant as a backward compatibility convenience for those 1687 systems with a bootloader that can't be upgraded to accommodate 1688 the documented boot protocol using a device tree. 1689 1690 Beware that there is very little in terms of protection against 1691 this option being confused by leftover garbage in memory that might 1692 look like a DTB header after a reboot if no actual DTB is appended 1693 to zImage. Do not leave this option active in a production kernel 1694 if you don't intend to always append a DTB. Proper passing of the 1695 location into r2 of a bootloader provided DTB is always preferable 1696 to this option. 1697 1698config ARM_ATAG_DTB_COMPAT 1699 bool "Supplement the appended DTB with traditional ATAG information" 1700 depends on ARM_APPENDED_DTB 1701 help 1702 Some old bootloaders can't be updated to a DTB capable one, yet 1703 they provide ATAGs with memory configuration, the ramdisk address, 1704 the kernel cmdline string, etc. Such information is dynamically 1705 provided by the bootloader and can't always be stored in a static 1706 DTB. To allow a device tree enabled kernel to be used with such 1707 bootloaders, this option allows zImage to extract the information 1708 from the ATAG list and store it at run time into the appended DTB. 1709 1710choice 1711 prompt "Kernel command line type" if ARM_ATAG_DTB_COMPAT 1712 default ARM_ATAG_DTB_COMPAT_CMDLINE_FROM_BOOTLOADER 1713 1714config ARM_ATAG_DTB_COMPAT_CMDLINE_FROM_BOOTLOADER 1715 bool "Use bootloader kernel arguments if available" 1716 help 1717 Uses the command-line options passed by the boot loader instead of 1718 the device tree bootargs property. If the boot loader doesn't provide 1719 any, the device tree bootargs property will be used. 1720 1721config ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND 1722 bool "Extend with bootloader kernel arguments" 1723 help 1724 The command-line arguments provided by the boot loader will be 1725 appended to the the device tree bootargs property. 1726 1727endchoice 1728 1729config CMDLINE 1730 string "Default kernel command string" 1731 default "" 1732 help 1733 On some architectures (e.g. CATS), there is currently no way 1734 for the boot loader to pass arguments to the kernel. For these 1735 architectures, you should supply some command-line options at build 1736 time by entering them here. As a minimum, you should specify the 1737 memory size and the root device (e.g., mem=64M root=/dev/nfs). 1738 1739choice 1740 prompt "Kernel command line type" if CMDLINE != "" 1741 default CMDLINE_FROM_BOOTLOADER 1742 depends on ATAGS 1743 1744config CMDLINE_FROM_BOOTLOADER 1745 bool "Use bootloader kernel arguments if available" 1746 help 1747 Uses the command-line options passed by the boot loader. If 1748 the boot loader doesn't provide any, the default kernel command 1749 string provided in CMDLINE will be used. 1750 1751config CMDLINE_EXTEND 1752 bool "Extend bootloader kernel arguments" 1753 help 1754 The command-line arguments provided by the boot loader will be 1755 appended to the default kernel command string. 1756 1757config CMDLINE_FORCE 1758 bool "Always use the default kernel command string" 1759 help 1760 Always use the default kernel command string, even if the boot 1761 loader passes other arguments to the kernel. 1762 This is useful if you cannot or don't want to change the 1763 command-line options your boot loader passes to the kernel. 1764endchoice 1765 1766config XIP_KERNEL 1767 bool "Kernel Execute-In-Place from ROM" 1768 depends on !ARM_LPAE && !ARCH_MULTIPLATFORM 1769 help 1770 Execute-In-Place allows the kernel to run from non-volatile storage 1771 directly addressable by the CPU, such as NOR flash. This saves RAM 1772 space since the text section of the kernel is not loaded from flash 1773 to RAM. Read-write sections, such as the data section and stack, 1774 are still copied to RAM. The XIP kernel is not compressed since 1775 it has to run directly from flash, so it will take more space to 1776 store it. The flash address used to link the kernel object files, 1777 and for storing it, is configuration dependent. Therefore, if you 1778 say Y here, you must know the proper physical address where to 1779 store the kernel image depending on your own flash memory usage. 1780 1781 Also note that the make target becomes "make xipImage" rather than 1782 "make zImage" or "make Image". The final kernel binary to put in 1783 ROM memory will be arch/arm/boot/xipImage. 1784 1785 If unsure, say N. 1786 1787config XIP_PHYS_ADDR 1788 hex "XIP Kernel Physical Location" 1789 depends on XIP_KERNEL 1790 default "0x00080000" 1791 help 1792 This is the physical address in your flash memory the kernel will 1793 be linked for and stored to. This address is dependent on your 1794 own flash usage. 1795 1796config XIP_DEFLATED_DATA 1797 bool "Store kernel .data section compressed in ROM" 1798 depends on XIP_KERNEL 1799 select ZLIB_INFLATE 1800 help 1801 Before the kernel is actually executed, its .data section has to be 1802 copied to RAM from ROM. This option allows for storing that data 1803 in compressed form and decompressed to RAM rather than merely being 1804 copied, saving some precious ROM space. A possible drawback is a 1805 slightly longer boot delay. 1806 1807config KEXEC 1808 bool "Kexec system call (EXPERIMENTAL)" 1809 depends on (!SMP || PM_SLEEP_SMP) 1810 depends on MMU 1811 select KEXEC_CORE 1812 help 1813 kexec is a system call that implements the ability to shutdown your 1814 current kernel, and to start another kernel. It is like a reboot 1815 but it is independent of the system firmware. And like a reboot 1816 you can start any kernel with it, not just Linux. 1817 1818 It is an ongoing process to be certain the hardware in a machine 1819 is properly shutdown, so do not be surprised if this code does not 1820 initially work for you. 1821 1822config ATAGS_PROC 1823 bool "Export atags in procfs" 1824 depends on ATAGS && KEXEC 1825 default y 1826 help 1827 Should the atags used to boot the kernel be exported in an "atags" 1828 file in procfs. Useful with kexec. 1829 1830config CRASH_DUMP 1831 bool "Build kdump crash kernel (EXPERIMENTAL)" 1832 help 1833 Generate crash dump after being started by kexec. This should 1834 be normally only set in special crash dump kernels which are 1835 loaded in the main kernel with kexec-tools into a specially 1836 reserved region and then later executed after a crash by 1837 kdump/kexec. The crash dump kernel must be compiled to a 1838 memory address not used by the main kernel 1839 1840 For more details see Documentation/admin-guide/kdump/kdump.rst 1841 1842config AUTO_ZRELADDR 1843 bool "Auto calculation of the decompressed kernel image address" 1844 help 1845 ZRELADDR is the physical address where the decompressed kernel 1846 image will be placed. If AUTO_ZRELADDR is selected, the address 1847 will be determined at run-time, either by masking the current IP 1848 with 0xf8000000, or, if invalid, from the DTB passed in r2. 1849 This assumes the zImage being placed in the first 128MB from 1850 start of memory. 1851 1852config EFI_STUB 1853 bool 1854 1855config EFI 1856 bool "UEFI runtime support" 1857 depends on OF && !CPU_BIG_ENDIAN && MMU && AUTO_ZRELADDR && !XIP_KERNEL 1858 select UCS2_STRING 1859 select EFI_PARAMS_FROM_FDT 1860 select EFI_STUB 1861 select EFI_GENERIC_STUB 1862 select EFI_RUNTIME_WRAPPERS 1863 help 1864 This option provides support for runtime services provided 1865 by UEFI firmware (such as non-volatile variables, realtime 1866 clock, and platform reset). A UEFI stub is also provided to 1867 allow the kernel to be booted as an EFI application. This 1868 is only useful for kernels that may run on systems that have 1869 UEFI firmware. 1870 1871config DMI 1872 bool "Enable support for SMBIOS (DMI) tables" 1873 depends on EFI 1874 default y 1875 help 1876 This enables SMBIOS/DMI feature for systems. 1877 1878 This option is only useful on systems that have UEFI firmware. 1879 However, even with this option, the resultant kernel should 1880 continue to boot on existing non-UEFI platforms. 1881 1882 NOTE: This does *NOT* enable or encourage the use of DMI quirks, 1883 i.e., the the practice of identifying the platform via DMI to 1884 decide whether certain workarounds for buggy hardware and/or 1885 firmware need to be enabled. This would require the DMI subsystem 1886 to be enabled much earlier than we do on ARM, which is non-trivial. 1887 1888endmenu 1889 1890menu "CPU Power Management" 1891 1892source "drivers/cpufreq/Kconfig" 1893 1894source "drivers/cpuidle/Kconfig" 1895 1896endmenu 1897 1898menu "Floating point emulation" 1899 1900comment "At least one emulation must be selected" 1901 1902config FPE_NWFPE 1903 bool "NWFPE math emulation" 1904 depends on (!AEABI || OABI_COMPAT) && !THUMB2_KERNEL 1905 help 1906 Say Y to include the NWFPE floating point emulator in the kernel. 1907 This is necessary to run most binaries. Linux does not currently 1908 support floating point hardware so you need to say Y here even if 1909 your machine has an FPA or floating point co-processor podule. 1910 1911 You may say N here if you are going to load the Acorn FPEmulator 1912 early in the bootup. 1913 1914config FPE_NWFPE_XP 1915 bool "Support extended precision" 1916 depends on FPE_NWFPE 1917 help 1918 Say Y to include 80-bit support in the kernel floating-point 1919 emulator. Otherwise, only 32 and 64-bit support is compiled in. 1920 Note that gcc does not generate 80-bit operations by default, 1921 so in most cases this option only enlarges the size of the 1922 floating point emulator without any good reason. 1923 1924 You almost surely want to say N here. 1925 1926config FPE_FASTFPE 1927 bool "FastFPE math emulation (EXPERIMENTAL)" 1928 depends on (!AEABI || OABI_COMPAT) && !CPU_32v3 1929 help 1930 Say Y here to include the FAST floating point emulator in the kernel. 1931 This is an experimental much faster emulator which now also has full 1932 precision for the mantissa. It does not support any exceptions. 1933 It is very simple, and approximately 3-6 times faster than NWFPE. 1934 1935 It should be sufficient for most programs. It may be not suitable 1936 for scientific calculations, but you have to check this for yourself. 1937 If you do not feel you need a faster FP emulation you should better 1938 choose NWFPE. 1939 1940config VFP 1941 bool "VFP-format floating point maths" 1942 depends on CPU_V6 || CPU_V6K || CPU_ARM926T || CPU_V7 || CPU_FEROCEON 1943 help 1944 Say Y to include VFP support code in the kernel. This is needed 1945 if your hardware includes a VFP unit. 1946 1947 Please see <file:Documentation/arm/vfp/release-notes.rst> for 1948 release notes and additional status information. 1949 1950 Say N if your target does not have VFP hardware. 1951 1952config VFPv3 1953 bool 1954 depends on VFP 1955 default y if CPU_V7 1956 1957config NEON 1958 bool "Advanced SIMD (NEON) Extension support" 1959 depends on VFPv3 && CPU_V7 1960 help 1961 Say Y to include support code for NEON, the ARMv7 Advanced SIMD 1962 Extension. 1963 1964config KERNEL_MODE_NEON 1965 bool "Support for NEON in kernel mode" 1966 depends on NEON && AEABI 1967 help 1968 Say Y to include support for NEON in kernel mode. 1969 1970endmenu 1971 1972menu "Power management options" 1973 1974source "kernel/power/Kconfig" 1975 1976config ARCH_SUSPEND_POSSIBLE 1977 depends on CPU_ARM920T || CPU_ARM926T || CPU_FEROCEON || CPU_SA1100 || \ 1978 CPU_V6 || CPU_V6K || CPU_V7 || CPU_V7M || CPU_XSC3 || CPU_XSCALE || CPU_MOHAWK 1979 def_bool y 1980 1981config ARM_CPU_SUSPEND 1982 def_bool PM_SLEEP || BL_SWITCHER || ARM_PSCI_FW 1983 depends on ARCH_SUSPEND_POSSIBLE 1984 1985config ARCH_HIBERNATION_POSSIBLE 1986 bool 1987 depends on MMU 1988 default y if ARCH_SUSPEND_POSSIBLE 1989 1990endmenu 1991 1992source "drivers/firmware/Kconfig" 1993 1994if CRYPTO 1995source "arch/arm/crypto/Kconfig" 1996endif 1997 1998source "arch/arm/Kconfig.assembler" 1999