1# SPDX-License-Identifier: GPL-2.0-only
2%YAML 1.2
3---
4$id: http://devicetree.org/schemas/mtd/jedec,spi-nor.yaml#
5$schema: http://devicetree.org/meta-schemas/core.yaml#
6
7title: SPI NOR flash ST M25Pxx (and similar) serial flash chips
8
9maintainers:
10  - Rob Herring <robh@kernel.org>
11
12allOf:
13  - $ref: mtd.yaml#
14  - $ref: /schemas/spi/spi-peripheral-props.yaml#
15
16properties:
17  compatible:
18    oneOf:
19      - items:
20          - pattern: "^((((micron|spansion|st),)?\
21              (m25p(40|80|16|32|64|128)|\
22              n25q(32b|064|128a11|128a13|256a|512a|164k)))|\
23              atmel,at25df(321a|641|081a)|\
24              everspin,mr25h(10|40|128|256)|\
25              (mxicy|macronix),mx25l(4005a|1606e|6405d|8005|12805d|25635e)|\
26              (mxicy|macronix),mx25u(4033|4035)|\
27              (spansion,)?s25fl(128s|256s1|512s|008k|064k|164k)|\
28              (sst|microchip),sst25vf(016b|032b|040b)|\
29              (sst,)?sst26wf016b|\
30              (sst,)?sst25wf(040b|080)|\
31              winbond,w25x(80|32)|\
32              (winbond,)?w25q(16|32(w|dw)?|64(dw)?|80bl|128(fw)?|256))$"
33          - const: jedec,spi-nor
34      - items:
35          - enum:
36              - issi,is25lp016d
37              - micron,mt25qu02g
38              - mxicy,mx25r1635f
39              - mxicy,mx25u6435f
40              - mxicy,mx25v8035f
41              - spansion,s25sl12801
42              - spansion,s25fs512s
43          - const: jedec,spi-nor
44      - const: jedec,spi-nor
45    description:
46      Must also include "jedec,spi-nor" for any SPI NOR flash that can be
47      identified by the JEDEC READ ID opcode (0x9F).
48
49  reg:
50    minItems: 1
51    maxItems: 2
52
53  m25p,fast-read:
54    type: boolean
55    description:
56      Use the "fast read" opcode to read data from the chip instead of the usual
57      "read" opcode. This opcode is not supported by all chips and support for
58      it can not be detected at runtime. Refer to your chips' datasheet to check
59      if this is supported by your chip.
60
61  broken-flash-reset:
62    type: boolean
63    description:
64      Some flash devices utilize stateful addressing modes (e.g., for 32-bit
65      addressing) which need to be managed carefully by a system. Because these
66      sorts of flash don't have a standardized software reset command, and
67      because some systems don't toggle the flash RESET# pin upon system reset
68      (if the pin even exists at all), there are systems which cannot reboot
69      properly if the flash is left in the "wrong" state. This boolean flag can
70      be used on such systems, to denote the absence of a reliable reset
71      mechanism.
72
73  reset-gpios:
74    description:
75      A GPIO line connected to the RESET (active low) signal of the device.
76      If "broken-flash-reset" is present then having this property does not
77      make any difference.
78
79  spi-cpol: true
80  spi-cpha: true
81
82dependencies:
83  spi-cpol: [ spi-cpha ]
84  spi-cpha: [ spi-cpol ]
85
86unevaluatedProperties: false
87
88examples:
89  - |
90    #include <dt-bindings/gpio/gpio.h>
91    spi {
92        #address-cells = <1>;
93        #size-cells = <0>;
94
95        flash@0 {
96            compatible = "spansion,m25p80", "jedec,spi-nor";
97            reg = <0>;
98            spi-max-frequency = <40000000>;
99            m25p,fast-read;
100            reset-gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
101        };
102    };
103...
104