| /openbmc/linux/arch/mips/loongson32/common/ |
| H A D | prom.c | 20 void __iomem *uart_base; in prom_init() local
29 uart_base = ioremap(LS1X_UART3_BASE, 0x0f); in prom_init()
31 uart_base = ioremap(LS1X_UART2_BASE, 0x0f); in prom_init()
33 uart_base = ioremap(LS1X_UART1_BASE, 0x0f); in prom_init()
35 uart_base = ioremap(LS1X_UART0_BASE, 0x0f); in prom_init()
36 setup_8250_early_printk_port((unsigned long)uart_base, 0, 0); in prom_init()
|
| /openbmc/linux/arch/mips/pic32/pic32mzda/ |
| H A D | early_console.c | 29 static void __iomem *uart_base; variable
56 __raw_writel(0, uart_base + U_MODE(port)); in configure_uart()
57 __raw_writel(((pbclk / baud) / 16) - 1, uart_base + U_BRG(port)); in configure_uart()
58 __raw_writel(UART_ENABLE, uart_base + U_MODE(port)); in configure_uart()
60 uart_base + PIC32_SET(U_STA(port))); in configure_uart()
138 uart_base = ioremap(PIC32_BASE_UART, 0xc00); in fw_init_early_console()
156 uart_base + U_STA(console_port)) & UART_TX_FULL) in prom_putchar()
159 __raw_writel(c, uart_base + U_TXR(console_port)); in prom_putchar()
|
| /openbmc/linux/arch/mips/generic/ |
| H A D | board-ocelot.c | 52 void __iomem *uart_base; in ocelot_earlyprintk_init() local
54 uart_base = ioremap(UART_UART, 0x20); in ocelot_earlyprintk_init()
55 setup_8250_early_printk_port((unsigned long)uart_base, 2, 50000); in ocelot_earlyprintk_init()
|
| /openbmc/u-boot/arch/arm/mach-omap2/am33xx/ |
| H A D | board.c | 400 struct uart_sys *uart_base = (struct uart_sys *)DEFAULT_UART_BASE; in uart_soft_reset() local
403 regval = readl(&uart_base->uartsyscfg); in uart_soft_reset()
405 writel(regval, &uart_base->uartsyscfg); in uart_soft_reset()
406 while ((readl(&uart_base->uartsyssts) & in uart_soft_reset()
411 regval = readl(&uart_base->uartsyscfg); in uart_soft_reset()
413 writel(regval, &uart_base->uartsyscfg); in uart_soft_reset()
|
| /openbmc/u-boot/drivers/serial/ |
| H A D | mcfuart.c | 85 uart_t *uart_base; in mcf_serial_init() local
88 uart_base = (uart_t *)CONFIG_SYS_UART_BASE; in mcf_serial_init()
91 return mcf_serial_init_common(uart_base, port_idx, gd->baudrate); in mcf_serial_init()
|
| /openbmc/linux/arch/mips/loongson2ef/common/ |
| H A D | Makefile | 15 obj-$(CONFIG_LOONGSON_UART_BASE) += uart_base.o
|
| /openbmc/linux/arch/alpha/kernel/ |
| H A D | smc37c669.c | 2074 SMC37c669_SERIAL_BASE_ADDRESS_REGISTER uart_base; in SMC37c669_init_local_config() local
2086 uart_base.as_uchar = in SMC37c669_init_local_config()
2096 local_config[SERIAL_0].port1 = uart_base.by_field.addr9_3 << 3; in SMC37c669_init_local_config()
2104 uart_base.as_uchar = in SMC37c669_init_local_config()
2109 local_config[SERIAL_1].port1 = uart_base.by_field.addr9_3 << 3; in SMC37c669_init_local_config()
|
| /openbmc/qemu/hw/isa/ |
| H A D | pc87312.c | 97 static const uint16_t uart_base[2][4] = { variable
112 return uart_base[idx & 1][(s->regs[REG_FAR] & FAR_UART_3_4) >> 6]; in get_uart_iobase()
|
| /openbmc/qemu/hw/mips/ |
| H A D | loongson3_bootp.h | 76 uint64_t uart_base; member
|
| H A D | loongson3_bootp.c | 74 s->uarts[0].uart_base = cpu_to_le64(virt_memmap[VIRT_UART].base); in init_system_loongson()
|
| /openbmc/linux/arch/mips/include/asm/mach-loongson64/ |
| H A D | boot_param.h | 76 u64 uart_base; member
|
| /openbmc/linux/drivers/usb/serial/ |
| H A D | io_ti.c | 90 u16 uart_base; member
554 port->uart_base + UMPMEM_OFFS_UART_LSR, 1, lsr); in tx_active()
2565 edge_port->uart_base = UMPMEM_BASE_UART1; in edge_port_probe()
2569 edge_port->uart_base = UMPMEM_BASE_UART2; in edge_port_probe()
2580 __func__, port->port_number, edge_port->uart_base, in edge_port_probe()
|
| /openbmc/linux/arch/mips/include/asm/sn/ |
| H A D | klconfig.h | 127 unsigned long uart_base; member
|
| /openbmc/linux/drivers/tty/serial/ |
| H A D | omap-serial.c | 106 unsigned int uart_base; member
|
| /openbmc/linux/ |
| H A D | opengrok0.0.log | [all...] |