/openbmc/linux/Documentation/networking/devlink/ |
H A D | iosm.rst | 26 the device during firmware flashing. 59 each having one secure bin file and at least one Loadmap/Region file. For flashing 61 data required for flashing. The data like region count and address of each region 64 If the device has to be fully erased before firmware flashing, user application 84 4) Once EBL is injected successfully, then the actual firmware flashing takes
|
/openbmc/linux/Documentation/gpu/amdgpu/ |
H A D | flashing.rst | 2 dGPU firmware flashing 21 On GPUs that support flashing an updated USB-C PD firmware image, the process
|
H A D | index.rst | 13 flashing
|
/openbmc/openbmc/meta-ampere/meta-common/recipes-phosphor/flash/phosphor-software-manager/ |
H A D | obmc-flash-host-bios@.service | 2 Description=Ampere service for flashing the Host firmware image
|
/openbmc/phosphor-bmc-code-mgmt/bmc/ |
H A D | obmc-flash-host-bios@.service.in | 7 ExecStart=echo Please add custom command for flashing image /tmp/image/%i
|
/openbmc/u-boot/doc/uImage.FIT/ |
H A D | update_uboot.its | 3 * Make sure the flashing addresses ('load' prop) is correct for your board!
|
/openbmc/linux/drivers/net/ethernet/mellanox/mlxfw/ |
H A D | Kconfig | 10 flashing common logic.
|
/openbmc/linux/Documentation/devicetree/bindings/phy/ |
H A D | phy-mapphone-mdm6600.txt | 9 normal mode versus USB flashing mode
|
/openbmc/u-boot/drivers/fastboot/ |
H A D | Kconfig | 100 bool "Skip empty pages when flashing NAND" 103 When flashing NAND enable the DROP_FFS flag to drop trailing all-0xff
|
/openbmc/u-boot/board/sunxi/ |
H A D | README.nand | 1 Allwinner NAND flashing
|
/openbmc/linux/drivers/net/ethernet/cavium/liquidio/ |
H A D | liquidio_common.h | 697 u64 flashing:1; member 703 u64 flashing:1;
|
/openbmc/linux/Documentation/admin-guide/ |
H A D | svga.rst | 66 Enter mode number or ``scan``: <flashing-cursor-here> 78 <flashing-cursor-here> encourages you to enter the item number or mode ID 97 what happens then. The screen will be probably flashing wildly for some time and
|
/openbmc/u-boot/doc/ |
H A D | README.avb2 | 106 After flashing U-boot don't forget to update environment and write new
|
H A D | README.mpc85xxcds | 79 U-Boot commands for downloading an image via tftp and flashing
|
/openbmc/u-boot/board/freescale/mx35pdk/ |
H A D | README | 79 If something goes wrong flashing the bootloader, it is always possible to
|
/openbmc/docs/designs/ |
H A D | firmware-update-via-usb.md | 76 re-flashing, this is not Reasonably, service support should have local access to
|
/openbmc/u-boot/test/py/ |
H A D | README.md | 213 This script should perform the entire flashing process synchronously; the 214 script should only exit once flashing is complete, and a board reset will 233 board-specific vendor flashing utility.
|
/openbmc/u-boot/board/synopsys/hsdk/ |
H A D | README | 56 header preceeding application image itself so before flashing anything
|
/openbmc/linux/Documentation/networking/device_drivers/ethernet/mellanox/mlx5/ |
H A D | kconfig.rst | 166 - CONFIG_MLXFW: When chosen, mlx5 firmware flashing support will be enabled (via devlink and ethtoo…
|
/openbmc/u-boot/examples/standalone/ |
H A D | README.smc91111_eeprom | 133 re-flashing U-Boot.
|
/openbmc/docs/architecture/code-update/ |
H A D | code-update-deprecated.md | 188 - During flashing the image, the status becomes `Writing images to flash`
|
/openbmc/u-boot/board/hisilicon/hikey/ |
H A D | README | 116 Note: To get USB host working, also disconnect the USB OTG cable used for flashing. Otherwise you
|
/openbmc/phosphor-ipmi-flash/ |
H A D | README.md | 131 The image flashing mechanism itself is the initramfs stage during reboot. It
|
/openbmc/openbmc/poky/documentation/dev-manual/ |
H A D | wic.rst | 516 ":ref:`dev-manual/bmaptool:flashing images using \`bmaptool\``" 724 <dev-manual/bmaptool:flashing images using \`bmaptool\`>` commands
|
/openbmc/openbmc-test-automation/lib/ |
H A D | utils.robot | 466 ... flashing has started. 473 ... PNOR flashing has completed.
|