| /openbmc/linux/arch/arm/mach-rockchip/ |
| H A D | pm.c | 144 * stabilization. Similar 30ms on 24MHz for the other in rk3288_slp_mode_set()
149 /* only wait for stabilization, if we turned the osc off */ in rk3288_slp_mode_set()
163 /* 30ms on a 24MHz clock for pmic stabilization */ in rk3288_slp_mode_set()
|
| /openbmc/linux/Documentation/process/ |
| H A D | 6.Followthrough.rst | 168 will almost certainly be removed during the stabilization period. Beyond
174 bugs to deal with. The stabilization period is your best opportunity to
177 the problems if at all possible. That's what the stabilization period is
|
| /openbmc/linux/drivers/cpufreq/ |
| H A D | powernow-k8.h | 18 u32 vstable; /* voltage stabilization time, units 20 us */
122 #define VST_UNITS_20US 20 /* Voltage Stabilization Time is in units of 20us */
|
| /openbmc/linux/drivers/net/wireless/intel/iwlwifi/fw/api/ |
| H A D | system.h | 20 * struct iwl_soc_configuration_cmd - Set device stabilization latency
|
| /openbmc/u-boot/arch/arm/include/asm/arch-tegra/ |
| H A D | ap.h | 8 /* Stabilization delays, in usec */
|
| /openbmc/u-boot/arch/arm/mach-tegra/ |
| H A D | cpu.h | 8 /* Stabilization delays, in usec */
|
| /openbmc/u-boot/drivers/video/ |
| H A D | am335x-fb.h | 64 * lcd-controller (pic stabilization)
|
| /openbmc/u-boot/arch/arm/mach-at91/ |
| H A D | spl_at91.c | 43 /* After stabilization, switch to Main Oscillator */ in lowlevel_clock_init()
|
| /openbmc/linux/Documentation/userspace-api/media/v4l/ |
| H A D | ext-ctrls-camera.rst | 328 .. _v4l2-image-stabilization:
331 Enables or disables image stabilization.
425 stabilization.
|
| /openbmc/openbmc/poky/documentation/test-manual/ |
| H A D | test-process.rst | 59 milestone releases (usually four) with the final one being stabilization
|
| /openbmc/linux/drivers/media/i2c/s5c73m3/ |
| H A D | s5c73m3-ctrls.c | 268 v4l2_dbg(1, s5c73m3_dbg, sd, "Image stabilization: %d\n", val); in s5c73m3_set_stabilization()
520 ctrls->stabilization = v4l2_ctrl_new_std(hdl, ops, in s5c73m3_init_controls()
|
| H A D | s5c73m3.h | 349 struct v4l2_ctrl *stabilization; member
|
| /openbmc/linux/arch/mips/alchemy/devboards/ |
| H A D | db1000.c | 232 msleep(400); /* stabilization time */ in db1100_mmc_set_power()
270 msleep(400); /* stabilization time */ in db1100_mmc1_set_power()
|
| H A D | db1200.c | 389 msleep(400); /* stabilization time */ in db1200_mmc_set_power()
486 msleep(400); /* stabilization time */ in pb1200_mmc1_set_power()
|
| /openbmc/linux/drivers/staging/media/atomisp/pci/ |
| H A D | atomisp_compat_ioctl32.h | 192 dvs_2500_config; /* Skylake: digital video stabilization config */
|
| /openbmc/linux/Documentation/devicetree/bindings/clock/ |
| H A D | baikal,bt1-ccu-div.yaml | 69 the output clock stabilization, EN - enable/disable the divider block,
|
| /openbmc/u-boot/arch/arm/mach-tegra/tegra20/ |
| H A D | warmboot_avp.c | 139 * use when returning from LP0 for PLL stabilization delays. in wb_start()
|
| /openbmc/linux/drivers/net/wireless/marvell/libertas/ |
| H A D | README | 107 p3 is Clock stabilization time in usec (0-65535)
|
| /openbmc/linux/fs/nilfs2/ |
| H A D | btnode.c | 8 * Fully revised by Ryusuke Konishi for stabilization and simplification.
|
| /openbmc/u-boot/board/renesas/sh7753evb/ |
| H A D | lowlevel_init.S | 78 /* oscillation stabilization time */
|
| /openbmc/u-boot/board/renesas/sh7752evb/ |
| H A D | lowlevel_init.S | 112 /* oscillation stabilization time */
|
| /openbmc/u-boot/arch/arm/mach-keystone/ |
| H A D | clock.c | 97 /* 100 micro sec for stabilization */ in configure_main_pll()
|
| /openbmc/linux/arch/arm/mach-tegra/ |
| H A D | sleep-tegra20.S | 225 /* 255uS delay for PLL stabilization */
|
| /openbmc/linux/drivers/staging/media/atomisp/include/linux/ |
| H A D | atomisp.h | 477 void *dvs_2500_config; /* Skylake: digital video stabilization config */
748 /* Digital Image Stabilization:
|
| /openbmc/linux/drivers/media/usb/pvrusb2/ |
| H A D | pvrusb2-hdw-internal.h | 250 /* Timer for measuring decoder stabilization time, which is the
|