Convert CONFIG_MII et al to Kconfig

This converts the following to Kconfig:
CONFIG_MII
CONFIG_DRIVER_TI_EMAC

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulas

Convert CONFIG_MII et al to Kconfig

This converts the following to Kconfig:
CONFIG_MII
CONFIG_DRIVER_TI_EMAC

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

show more ...

configs: Migrate CONFIG_NR_DRAM_BANKS

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANK

configs: Migrate CONFIG_NR_DRAM_BANKS

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Merge git://git.denx.de/u-boot-imx

wandboard: Remove hardcoded baudrate from "console" variable

We should use the baudrate variable available inside U-Boot
environment to allow it to be changed dynamically.

Signed-off-by: Otavio Sal

wandboard: Remove hardcoded baudrate from "console" variable

We should use the baudrate variable available inside U-Boot
environment to allow it to be changed dynamically.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>

show more ...

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Migrate CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to Kconfig

Convert CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to Kconfig

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lu

Migrate CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to Kconfig

Convert CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to Kconfig

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Petr Vorel <petr.vorel@gmail.com>
Reviewed-by: Petr Vorel <petr.vorel at gmail.com>

show more ...

treewide: Migrate CONFIG_DISPLAY_BOARDINFO_LATE to Kconfig

Migrate the CONFIG_DISPLAY_BOARDINFO_LATE option to Kconfig.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
[trini: Re-run migration]
Signe

treewide: Migrate CONFIG_DISPLAY_BOARDINFO_LATE to Kconfig

Migrate the CONFIG_DISPLAY_BOARDINFO_LATE option to Kconfig.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Remove config_distro_defaults.h

With the contents of config_distro_defaults.h migrated to Kconfig,
we can remove this header file completely

Signed-off-by: Adam Ford <aford173@gmail.com>

ata: Migrate CONFIG_LIBATA to Kconfig

This symbol enables some library code used by various SATA drivers,
so make this a non-user-visible symbol select'ed by the respective
drivers, and let moveconf

ata: Migrate CONFIG_LIBATA to Kconfig

This symbol enables some library code used by various SATA drivers,
so make this a non-user-visible symbol select'ed by the respective
drivers, and let moveconfig handle the rest.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>

show more ...

ata: Migrate CONFIG_DWC_AHSATA to Kconfig

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>

Kconfig: Introduce USE_BOOTCOMMAND and migrate BOOTCOMMAND

We first introduce CONFIG_USE_BOOTCOMMAND, similar to
CONFIG_USE_BOOTARGS. We then migrate CONFIG_BOOTCOMMAND for most
CONFIG_DISTRO_DEFAU

Kconfig: Introduce USE_BOOTCOMMAND and migrate BOOTCOMMAND

We first introduce CONFIG_USE_BOOTCOMMAND, similar to
CONFIG_USE_BOOTARGS. We then migrate CONFIG_BOOTCOMMAND for most
CONFIG_DISTRO_DEFAULT users. In some cases platforms have a complex
scheme around this usage, and these have been defered for the moment so
that platform maintainers can work on a migration plan.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>

show more ...

Merge branch 'master' of git://www.denx.de/git/u-boot-imx

wandboard: Add support for the MX6QP variant

Add support for the latest MX6QP wandboard variant.

Based on Richard Hu's work from Technexion's U-Boot tree.

Signed-off-by: Fabio Estevam <fabio.estev

wandboard: Add support for the MX6QP variant

Add support for the latest MX6QP wandboard variant.

Based on Richard Hu's work from Technexion's U-Boot tree.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>

show more ...

Merge git://www.denx.de/git/u-boot-imx

wandboard: Add support for the latest revd1 revision

Latest wandboard hardware revision is revd1, which brings the following
new features:

- PFUZE100 PMIC
- AR8035 Ethernet PHY
- Upgrade Wifi/BT ch

wandboard: Add support for the latest revd1 revision

Latest wandboard hardware revision is revd1, which brings the following
new features:

- PFUZE100 PMIC
- AR8035 Ethernet PHY
- Upgrade Wifi/BT chip to BCM4339/BCM43430.

The detection mechanism is to probe the PMIC and when it is
found, then the revision of the board is revd1.

As the detection is done via PMIC, we need to print the board version
at a later stage via CONFIG_DISPLAY_BOARDINFO_LATE and also need
to disable CONFIG_DISPLAY_BOARDINFO, which is done much earlier.

Make the necessary adjustments for the AR8035 PHY to work on revd1.

Based on Richard Hu's work from Technexion's U-Boot tree.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-video

ipu_common: Let the MX6 IPU clock be calculated in run-time

MX6Q/QP IPU operates at 264MHz and MX6DL IPU at 198MHz.

When running a SPL target, which supports multiple MX6 variants we cannot
properl

ipu_common: Let the MX6 IPU clock be calculated in run-time

MX6Q/QP IPU operates at 264MHz and MX6DL IPU at 198MHz.

When running a SPL target, which supports multiple MX6 variants we cannot
properly setup the IPU clock frequency via CONFIG_IPUV3_CLK option as
such decision is done in build-time currently.

Remove the CONFIG_IPUV3_CLK option and let the IPU clock frequency be
configured in run-time on mx6.

Reported-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
[agust: fixed #endif in cgtqmx6eval.h]
Signed-off-by: Anatolij Gustschin <agust@denx.de>

show more ...

Merge git://www.denx.de/git/u-boot-imx

Update pfla02 for setenv changes and PHYLIB/etc migration to Kconfig.

Signed-off-by: Tom Rini <trini@konsulko.com>

Merge branch 'master' of git://git.denx.de/u-boot-net

Move PHYLIB to Kconfig

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

arm: imx: Enable booting from SATA on wandboard.

Enable booting from SATA on the wandboard.

Sata support was already enabled, but distro_bootcmd is not configured
to boot from it.

Signed-off-by: V

arm: imx: Enable booting from SATA on wandboard.

Enable booting from SATA on the wandboard.

Sata support was already enabled, but distro_bootcmd is not configured
to boot from it.

Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

show more ...

Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_IS_IN_MMC
CONFIG_ENV_IS_IN_NAND
CONFIG_ENV_IS_IN_UBI
CONFIG_ENV_IS_NOWHERE

Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_IS_IN_MMC
CONFIG_ENV_IS_IN_NAND
CONFIG_ENV_IS_IN_UBI
CONFIG_ENV_IS_NOWHERE

In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.

In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.

There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with

./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC

And then manual updates. This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Merge branch 'master' of git://www.denx.de/git/u-boot-imx

wandboard: Use PARTUUID to specify the rootfs location

Currently the rootfs location is passed via mmcblk number and the
problem with this approach is that the mmcblk number for the eMMC
changes dep

wandboard: Use PARTUUID to specify the rootfs location

Currently the rootfs location is passed via mmcblk number and the
problem with this approach is that the mmcblk number for the eMMC
changes depending on the kernel version.

In order to avoid such issue, use UUID method to specify the rootfs
location.

This change was made based on U-Boot commit:

- ca4f338e2efece5196eb2178e5f7d07be828da6e

Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

show more ...

Merge git://git.denx.de/u-boot-dm