Merge branch 'master' of git://git.denx.de/u-boot

Signed-off-by: Stefano Babic <sbabic@denx.de>

Merge branch '2019-03-25-master-imports'

- Convert various SPI related options to Kconfig

Convert CONFIG_ENV_SPI_* to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_SPI_BUS
CONFIG_ENV_SPI_CS
CONFIG_ENV_SPI_MAX_HZ
CONFIG_ENV_SPI_MODE

Most of time these value are not n

Convert CONFIG_ENV_SPI_* to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_SPI_BUS
CONFIG_ENV_SPI_CS
CONFIG_ENV_SPI_MAX_HZ
CONFIG_ENV_SPI_MODE

Most of time these value are not needed, CONFIG_SF_DEFAULT
with same value is used, so I introduced CONFIG_USE_ENV_SPI_*
to force the associated value for the environment.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>

show more ...

Convert CONFIG_SF_DEFAULT_* to Kconfig

This converts the following to Kconfig:
CONFIG_SF_DEFAULT_BUS
CONFIG_SF_DEFAULT_CS
CONFIG_SF_DEFAULT_MODE
CONFIG_SF_DEFAULT_SPEED

I use moveconfig scr

Convert CONFIG_SF_DEFAULT_* to Kconfig

This converts the following to Kconfig:
CONFIG_SF_DEFAULT_BUS
CONFIG_SF_DEFAULT_CS
CONFIG_SF_DEFAULT_MODE
CONFIG_SF_DEFAULT_SPEED

I use moveconfig script and then manual check on generated u-boot.cfg
to solve the remaining issue.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>

show more ...

Merge tag 'u-boot-imx-20181025' of git://git.denx.de/u-boot-imx

Merged imx8 architecture, fix build for imx8 + warnings

Kconfig: Convert CONFIG_IMX_WATCHDOG to Kconfig

Move this option to Kconfig and tidy up the config file of eight
boards which use it.

Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>

ARM: display5: Remove "factory procedure" from display5 board config

This code now is regarded as dead one and hence shall be removed.

Signed-off-by: Lukasz Majewski <lukma@denx.de>

display5: Introduce fitImg_fw_sz variable

This cosmetic change allow easy adjustment of the to-load kernel size if
needed.

Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Lukasz M

display5: Introduce fitImg_fw_sz variable

This cosmetic change allow easy adjustment of the to-load kernel size if
needed.

Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Lukasz Majewski <lukma@denx.de>

show more ...

Convert CONFIG_MISC_INIT_R to Kconfig

This converts the following to Kconfig:
CONFIG_MISC_INIT_R

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Update the defaults logic slightly]
Signed-

Convert CONFIG_MISC_INIT_R to Kconfig

This converts the following to Kconfig:
CONFIG_MISC_INIT_R

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Update the defaults logic slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Migrate bootlimit to Kconfig

Migrate boards which set bootlimit in the environment to Kconfig.

We exclude gurnard_defconfig which includes a bootlimit=, but doesn't set
CONFIG_BOOTCOUNT_LIMIT, so w

Migrate bootlimit to Kconfig

Migrate boards which set bootlimit in the environment to Kconfig.

We exclude gurnard_defconfig which includes a bootlimit=, but doesn't set
CONFIG_BOOTCOUNT_LIMIT, so we'd fail to include a bootlimit setting
if we migrated it.

display5_defconfig and display5_factory_defconfig share a SYS_CONFIG_NAME,
but only display5_defconfig enables CONFIG_BOOTCOUNT_LIMIT, so we fail to
set bootlimit= in display5_factory_defconfig. This is okay because the
display5_factory_defconfig doesn't need to have it set, as it is only
meant to prepare the board in the factory.

Environment changes for all modified configs as seen from buildman:

boards.cfg is up to date. Nothing to do.
Summary of 3 commits for 32 boards (8 threads, 1 job per thread)
01: Merge git://git.denx.de/u-boot-x86
arm: + draco etamin rastaban pxm2 display5 thuban rut
02: Add BOOTCOUNT_BOOTLIMIT to set reboot limit
03: Migrate bootlimit to Kconfig
- display5_factory: bootlimit=3

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>

show more ...

Convert CONFIG_MII et al to Kconfig

This converts the following to Kconfig:
CONFIG_MII
CONFIG_DRIVER_TI_EMAC

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulas

Convert CONFIG_MII et al to Kconfig

This converts the following to Kconfig:
CONFIG_MII
CONFIG_DRIVER_TI_EMAC

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

show more ...

configs: Migrate CONFIG_NR_DRAM_BANKS

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANK

configs: Migrate CONFIG_NR_DRAM_BANKS

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Convert CONFIG_MTD_PARTITIONS et al to Kconfig

This converts the following to Kconfig:
CONFIG_MTD_PARTITIONS
CONFIG_MTD_DEVICE

Signed-off-by: Adam Ford <aford173@gmail.com>

Merge git://git.denx.de/u-boot-imx

display5: config: Add GPT verification and restoration code on SWUpdate entry

If GPT gets broken, then after N boot attempts we will run the SWUpdate
restoration image.
On its enter we will check GP

display5: config: Add GPT verification and restoration code on SWUpdate entry

If GPT gets broken, then after N boot attempts we will run the SWUpdate
restoration image.
On its enter we will check GPT and restore it if needed.

To test it:
display5 > mmc write 0x12000000 4 8

It will overwrite the primary GPT table.

Signed-off-by: Lukasz Majewski <lukma@denx.de>

show more ...

display5: config: Reduce rootfs2 (BACKUP) size from 1528M to 512M

Signed-off-by: Lukasz Majewski <lukma@denx.de>

display5: config: Add cma=256M to command line arguments

Signed-off-by: Lukasz Majewski <lukma@denx.de>

display5: config: Update swupdate initramfs file name (now supporting ext4)

After moving to swupdate 2017.07, the default fs for swupdate rootfs
is ext4, not ext3.

Signed-off-by: Lukasz Majewski <l

display5: config: Update swupdate initramfs file name (now supporting ext4)

After moving to swupdate 2017.07, the default fs for swupdate rootfs
is ext4, not ext3.

Signed-off-by: Lukasz Majewski <lukma@denx.de>

show more ...

display5: config: factory: Update BACKUP rootfs in factory mode

After splitting rootfs images to BACKUP and ACTIVE, the "factory"
u-boot also needs to update the former.

Signed-off-by: Lukasz Majew

display5: config: factory: Update BACKUP rootfs in factory mode

After splitting rootfs images to BACKUP and ACTIVE, the "factory"
u-boot also needs to update the former.

Signed-off-by: Lukasz Majewski <lukma@denx.de>

show more ...

display5: config: Provide 'tftp_mmc_rootfs_bkp' command to write BACKUP rootfs

Signed-off-by: Lukasz Majewski <lukma@denx.de>

display5: wdt: Enable WDT support (both SPL and u-boot)

Test case:

The fitImage gets corrupted:

truncate -c -s 3M fitImage
run tftp_mmc_fitImg
setenv boot_os y
reset

[board shall hang in SPL with

display5: wdt: Enable WDT support (both SPL and u-boot)

Test case:

The fitImage gets corrupted:

truncate -c -s 3M fitImage
run tftp_mmc_fitImg
setenv boot_os y
reset

[board shall hang in SPL with
"Trying to boot from MMC1" information]

Then after X seconds WDT is causing board to reset. After N boot attempts
we enter recovery mode.

Signed-off-by: Lukasz Majewski <lukma@denx.de>

show more ...

display5: Support for the emergency PAD pressing

To enter the special mode, one needs to short cut two pads with e.g. screw
driver.

After power up the SPL will execute u-boot in which proper action

display5: Support for the emergency PAD pressing

To enter the special mode, one needs to short cut two pads with e.g. screw
driver.

After power up the SPL will execute u-boot in which proper actions will be
taken.

It is worth noting that we do not alter envs (even the BOOT_FROM variable)
and unconditionally go to recovery.

Signed-off-by: Lukasz Majewski <lukma@denx.de>

show more ...

display5: config: Update SPI-NOR partition for larger swupdate-initramfs

The SPI-NOR partition information has been updated to store
swupdate-kernel-FIT just after envs as well as two times larger
s

display5: config: Update SPI-NOR partition for larger swupdate-initramfs

The SPI-NOR partition information has been updated to store
swupdate-kernel-FIT just after envs as well as two times larger
swupdate-initramfs image.

Signed-off-by: Lukasz Majewski <lukma@denx.de>

show more ...

display5: config: Remove support for Linux initramfs recovery image boot

This is a prerequisite patch to combine SWUpdate and Linux recovery
initramfs images.

It removes the support for it.

Signed

display5: config: Remove support for Linux initramfs recovery image boot

This is a prerequisite patch to combine SWUpdate and Linux recovery
initramfs images.

It removes the support for it.

Signed-off-by: Lukasz Majewski <lukma@denx.de>

show more ...

display5: config: Reset the board when bootm fails

Since display5 is now supporting boot counting, we can just reset the
board when bootm fails (i.e. it doesn't boot the fitImage kernel for
any reas

display5: config: Reset the board when bootm fails

Since display5 is now supporting boot counting, we can just reset the
board when bootm fails (i.e. it doesn't boot the fitImage kernel for
any reason).

Signed-off-by: Lukasz Majewski <lukma@denx.de>

show more ...