Merge branch 'master' of git://git.denx.de/u-boot

Signed-off-by: Stefano Babic <sbabic@denx.de>

Merge branch '2019-03-25-master-imports'

- Convert various SPI related options to Kconfig

Convert CONFIG_ENV_SPI_* to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_SPI_BUS
CONFIG_ENV_SPI_CS
CONFIG_ENV_SPI_MAX_HZ
CONFIG_ENV_SPI_MODE

Most of time these value are not n

Convert CONFIG_ENV_SPI_* to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_SPI_BUS
CONFIG_ENV_SPI_CS
CONFIG_ENV_SPI_MAX_HZ
CONFIG_ENV_SPI_MODE

Most of time these value are not needed, CONFIG_SF_DEFAULT
with same value is used, so I introduced CONFIG_USE_ENV_SPI_*
to force the associated value for the environment.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>

show more ...

Convert CONFIG_SF_DEFAULT_* to Kconfig

This converts the following to Kconfig:
CONFIG_SF_DEFAULT_BUS
CONFIG_SF_DEFAULT_CS
CONFIG_SF_DEFAULT_MODE
CONFIG_SF_DEFAULT_SPEED

I use moveconfig scr

Convert CONFIG_SF_DEFAULT_* to Kconfig

This converts the following to Kconfig:
CONFIG_SF_DEFAULT_BUS
CONFIG_SF_DEFAULT_CS
CONFIG_SF_DEFAULT_MODE
CONFIG_SF_DEFAULT_SPEED

I use moveconfig script and then manual check on generated u-boot.cfg
to solve the remaining issue.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>

show more ...

Convert CONFIG_MTD_PARTITIONS et al to Kconfig

This converts the following to Kconfig:
CONFIG_MTD_PARTITIONS
CONFIG_MTD_DEVICE

Signed-off-by: Adam Ford <aford173@gmail.com>

board/BuR/brppt1: convert brppt1 boards to driver model

- add a devicetree for each variant (mmc, spi, nand)
- drop unneeded code from board and bur/common
- drop unneeded stuff from config header f

board/BuR/brppt1: convert brppt1 boards to driver model

- add a devicetree for each variant (mmc, spi, nand)
- drop unneeded code from board and bur/common
- drop unneeded stuff from config header files
- minor adaptions to be compliant with driver model (requesting gpio,..)
- harmonize the commandset over all brppt1 targets

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>

show more ...

board/BuR/brppt1: implement more flexible boot process

With this commit we do:

- set the bootdelay in all brppt1 defconfigs to 0, this makes
development easier, since we can break into serial conso

board/BuR/brppt1: implement more flexible boot process

With this commit we do:

- set the bootdelay in all brppt1 defconfigs to 0, this makes
development easier, since we can break into serial console.

- move CONFIG_BOOTCOMMAND from header file to defconfig

- introduce b_mode variable for selecting the final boot-target.
This b_mode represents the boot-switch, which can found on most b&r
targets. On the brppt1 this boot-switch is derived from some gpio and
the bootcounter within the RTC block, making it so possible to force
a boot-target (as example for repair-case).

- refactor the environment for booting new flexible way
primary we want to get some bootscr.img within the mass-storage,
this script then loads everything needed for the boot.
For legacy reason we implement the t30lgcy#x boot targets, booting the
already delivered linux-images.

- make space for the cfgscr within mtdparts on brppt1_nand

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>

show more ...

board/BuR/brppt1: drop dead code (CONFIG_SPL_OS_BOOT)

The falcon mode was never used on this board, there is also no plan to
use it. So drop this dead code.

Signed-off-by: Hannes Schmelzer <oe5hpm@

board/BuR/brppt1: drop dead code (CONFIG_SPL_OS_BOOT)

The falcon mode was never used on this board, there is also no plan to
use it. So drop this dead code.

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>

show more ...

board/BuR/brppt1: drop LCD-support

On this linux target long time ago the OS is using DRM driver for
handling video output, the pre initialization of u-boot and the display
summary screen is obsolet

board/BuR/brppt1: drop LCD-support

On this linux target long time ago the OS is using DRM driver for
handling video output, the pre initialization of u-boot and the display
summary screen is obsolete. With this patch we drop the LCD-support from
thisd board.

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>

show more ...

board/BuR: drop devicetree loading and lcd setup for linux-targets

This patch drops the lcd-screen setup, the summary screen and getting
mac-addresses based on a previous loaded device-tree for lin

board/BuR: drop devicetree loading and lcd setup for linux-targets

This patch drops the lcd-screen setup, the summary screen and getting
mac-addresses based on a previous loaded device-tree for linux targets.
Selecting those linux target is simple, since we have only the brppt1.

In detail we do:
- drop the common lcd-setup code which relys on a fdt_blob
- drop the common dtb loading mechanism
- drop the now obsolete CONFIG_USE_FDT from board header and whitelist.

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>

show more ...

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Convert CONFIG_SPI to Kconfig

This converts the following to Kconfig:
CONFIG_SPI

This partly involves updating code that assumes that CONFIG_SPI implies
things that are specific to the MPC8xx SP

Convert CONFIG_SPI to Kconfig

This converts the following to Kconfig:
CONFIG_SPI

This partly involves updating code that assumes that CONFIG_SPI implies
things that are specific to the MPC8xx SPI driver. For now, just update
the CONFIG tests. This also involves reworking the default for
CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a
reasonable default, as it does not cause any compile failures.

Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

spl: spi: Move CONFIG_SPL_SPI_LOAD to Kconfig

Add Kconfig entry for CONFIG_SPL_SPI_LOAD symbol and move all
configurations using it to Kconfig.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail

spl: spi: Move CONFIG_SPL_SPI_LOAD to Kconfig

Add Kconfig entry for CONFIG_SPL_SPI_LOAD symbol and move all
configurations using it to Kconfig.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>

show more ...

bootcount: Migrate CONFIG_SYS_BOOTCOUNT_ADDR

Migrate the users of CONFIG_SYS_BOOTCOUNT_ADDR to Kconfig. We can
provide a default for BOOTCOUNT_AM33XX as that's a specific part of the
RTC in use. W

bootcount: Migrate CONFIG_SYS_BOOTCOUNT_ADDR

Migrate the users of CONFIG_SYS_BOOTCOUNT_ADDR to Kconfig. We can
provide a default for BOOTCOUNT_AM33XX as that's a specific part of the
RTC in use. We can also provide a default for ARCH_LS1043A and
ARCH_LS1021A as they had been previously calculated and their symbols
are in Kconfig. In the case of other QE-enabled platforms, they are not
so we must update the relevant defconfig files. The previous default
only applied in some cases, even on a specific SoC family.

Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Alex Kiernan <alex.kiernan@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Convert CONFIG_BOOTCOUNT_AM33XX to Kconfig

This converts the following to Kconfig:
CONFIG_BOOTCOUNT_AM33XX

Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Hannes Schmelzer <hannes.schme

Convert CONFIG_BOOTCOUNT_AM33XX to Kconfig

This converts the following to Kconfig:
CONFIG_BOOTCOUNT_AM33XX

Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Acked-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>

show more ...

Convert CONFIG_BOOTCOUNT_LIMIT to Kconfig

This converts the following to Kconfig:
CONFIG_BOOTCOUNT_LIMIT

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Alex Kiernan <alex.kiernan@gmai

Convert CONFIG_BOOTCOUNT_LIMIT to Kconfig

This converts the following to Kconfig:
CONFIG_BOOTCOUNT_LIMIT

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Acked-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>

show more ...

fs: Migrate ext4 to Kconfig

Migrate the following symbols to Kconfig:

CONFIG_FS_EXT4
CONFIG_EXT4_WRITE

The definitions in config_fallbacks.h can now be expressed in Kconfig.

Signed-off-by: Tuomas

fs: Migrate ext4 to Kconfig

Migrate the following symbols to Kconfig:

CONFIG_FS_EXT4
CONFIG_EXT4_WRITE

The definitions in config_fallbacks.h can now be expressed in Kconfig.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>

show more ...

Convert CONFIG_USB_MUSB_OMAP2PLUS et al to Kconfig

This converts the following to Kconfig:
CONFIG_USB_MUSB_OMAP2PLUS
CONFIG_USB_MUSB_AM35X
CONFIG_USB_MUSB_DSPS
CONFIG_USB_MUSB_PIO_ONLY

Convert CONFIG_USB_MUSB_OMAP2PLUS et al to Kconfig

This converts the following to Kconfig:
CONFIG_USB_MUSB_OMAP2PLUS
CONFIG_USB_MUSB_AM35X
CONFIG_USB_MUSB_DSPS
CONFIG_USB_MUSB_PIO_ONLY

Signed-off-by: Adam Ford <aford173@gmail.com>

show more ...

Kconfig: Migrate MTDIDS_DEFAULT / MTDPARTS_DEFAULT

We move all instances of CONFIG_MTDIDS_DEFAULT and
CONFIG_MTDPARTS_DEFAULT from the header files to the defconfig files.
There's a few cases here w

Kconfig: Migrate MTDIDS_DEFAULT / MTDPARTS_DEFAULT

We move all instances of CONFIG_MTDIDS_DEFAULT and
CONFIG_MTDPARTS_DEFAULT from the header files to the defconfig files.
There's a few cases here where we need to expand upon what was in the
header file.

Tested-by: Adam Ford <aford173@gmail.com> #omap3_logic
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Convert CONFIG_NAND_OMAP_GPMC et al and CONFIG_NAND_MXC to Kconfig

This converts the following to Kconfig:
CONFIG_NAND_MXC
CONFIG_NAND_OMAP_GPMC
CONFIG_NAND_OMAP_GPMC_PREFETCH
CONFIG_NAN

Convert CONFIG_NAND_OMAP_GPMC et al and CONFIG_NAND_MXC to Kconfig

This converts the following to Kconfig:
CONFIG_NAND_MXC
CONFIG_NAND_OMAP_GPMC
CONFIG_NAND_OMAP_GPMC_PREFETCH
CONFIG_NAND_OMAP_ELM
CONFIG_SPL_NAND_AM33XX_BCH
CONFIG_SPL_NAND_SIMPLE
CONFIG_SYS_NAND_BUSWIDTH_16BIT

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
[trini: Finish migration of CONFIG_SPL_NAND_SIMPLE, fix some build issues,
add CONFIG_NAND_MXC so we can do CONFIG_SYS_NAND_BUSWIDTH_16BIT]
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Convert CONFIG_OMAP3_SPI to Kconfig

This converts the following to Kconfig:
CONFIG_OMAP3_SPI

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Minor comment tweaks]
Signed-off-by: Tom Rini <

Convert CONFIG_OMAP3_SPI to Kconfig

This converts the following to Kconfig:
CONFIG_OMAP3_SPI

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Minor comment tweaks]
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Convert CONFIG_CMD_SPL_WRITE_SIZE to Kconfig

This converts the following to Kconfig:
CONFIG_CMD_SPL_WRITE_SIZE

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail

Convert CONFIG_CMD_SPL_WRITE_SIZE to Kconfig

This converts the following to Kconfig:
CONFIG_CMD_SPL_WRITE_SIZE

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

show more ...

Convert CONFIG_CMD_SPL_NAND_OFS to Kconfig

This converts the following to Kconfig:
CONFIG_CMD_SPL_NAND_OFS

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com

Convert CONFIG_CMD_SPL_NAND_OFS to Kconfig

This converts the following to Kconfig:
CONFIG_CMD_SPL_NAND_OFS

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

show more ...

Convert CONFIG_ENV_IS_IN_SPI_FLASH to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_IS_IN_SPI_FLASH

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_IS_IN_MMC
CONFIG_ENV_IS_IN_NAND
CONFIG_ENV_IS_IN_UBI
CONFIG_ENV_IS_NOWHERE

Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_IS_IN_MMC
CONFIG_ENV_IS_IN_NAND
CONFIG_ENV_IS_IN_UBI
CONFIG_ENV_IS_NOWHERE

In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.

In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.

There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with

./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC

And then manual updates. This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...