SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Merge branch 'master' of git://www.denx.de/git/u-boot-sunxi

sunxi: axp2xx: disable ldoio0/1 at boot

When cold-booting the ldoio0/1 regulators are always off / the
gpios are always at tristate. But when re-booting from android these
are sometimes on. Disable

sunxi: axp2xx: disable ldoio0/1 at boot

When cold-booting the ldoio0/1 regulators are always off / the
gpios are always at tristate. But when re-booting from android these
are sometimes on. Disable them at axp_init time (iow as early as possible)
to remove this difference between a cold boot and a reboot.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot

Signed-off-by: Stefano Babic <sbabic@denx.de>

Merge branch 'master' of http://git.denx.de/u-boot-sunxi

power: axp221: Remove switch case to simplify axp_set_eldo

The ELDO enable bits and registers are contiguous for axp221. Instead
of a switch case testing against the index, just use the index to shi

power: axp221: Remove switch case to simplify axp_set_eldo

The ELDO enable bits and registers are contiguous for axp221. Instead
of a switch case testing against the index, just use the index to shift
the bit or register offset.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

show more ...

Merge branch 'master' of http://git.denx.de/u-boot-sunxi

power: axp: merge separate DLDO functions into 1

Instead of one function for each DLDO regulator, make 1 function that
takes an extra "index". Since the control bits for the DLDO regulators
are cont

power: axp: merge separate DLDO functions into 1

Instead of one function for each DLDO regulator, make 1 function that
takes an extra "index". Since the control bits for the DLDO regulators
are contiguous, this makes the function very simple. This removes a lot
of duplicate code.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

show more ...

sunxi: Implement poweroff support for axp221 pmic

Adds poweroff support for axp221 pmic.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

Merge branch 'master' of git://git.denx.de/u-boot

sunxi: power: Drop protection against multiple calls from axp221 axp_init()

The only thing axp221.c's axp_init() does which needs protection
against multiple calls is calling pmic_bus_init, and pmic

sunxi: power: Drop protection against multiple calls from axp221 axp_init()

The only thing axp221.c's axp_init() does which needs protection
against multiple calls is calling pmic_bus_init, and pmic_bus_init()
itself is already protected against being called multiple times.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

show more ...

sunxi: power: Unify axp pmic function names

Stop prefixing the axp functions for setting voltages, etc. with the
model number, there ever is only one pmic driver built into u-boot,
this allows simpl

sunxi: power: Unify axp pmic function names

Stop prefixing the axp functions for setting voltages, etc. with the
model number, there ever is only one pmic driver built into u-boot,
this allows simplifying the callers.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

show more ...

Merge branch 'u-boot/master' into 'u-boot-arm/master'

Merge branch 'master' of git://git.denx.de/u-boot-sunxi

sunxi: axp: Move axp gpio code to a separate axpi-gpio driver

Move the axp-gpio code out of the drivers/power/axp*.c code, and into
a new separate axpi-gpio driver.

This change drops supports for t

sunxi: axp: Move axp gpio code to a separate axpi-gpio driver

Move the axp-gpio code out of the drivers/power/axp*.c code, and into
a new separate axpi-gpio driver.

This change drops supports for the gpio3 pin on the axp209, as that requires
special handling, and no boards are using it.

Besides cleaning things up by moving the code to a separate driver, as
a bonus this change also adds support for the (non vusb) gpio pins on the
axp221 and the gpio pins on the axp152.

The new axp-gpio driver gets its own Kconfig option, and is only enabled
on boards which need it. Besides that it only gets enabled in the regular
u-boot build and not for the SPL as we never need it in the SPL.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

show more ...

sunxi: axp: Move axp pmic register helpers to a separate file

Move the register helpers used to access the registers via p2wi resp.
rsb bus on the otherwise identical axp221 and axp223 pmics to a se

sunxi: axp: Move axp pmic register helpers to a separate file

Move the register helpers used to access the registers via p2wi resp.
rsb bus on the otherwise identical axp221 and axp223 pmics to a separate
file, so that they can be used by the upcoming standalone axp gpio driver
too.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

show more ...

sunxi: axp: Change axp_gpio_foo prototypes to match gpio uclass ops

Change the axp_gpio_foo function prototypes to match the gpio uclass op
prototypes, this is a preparation patch for moving the axp

sunxi: axp: Change axp_gpio_foo prototypes to match gpio uclass ops

Change the axp_gpio_foo function prototypes to match the gpio uclass op
prototypes, this is a preparation patch for moving the axp gpio code to
a separate driver-model gpio driver.

Note that the ugly calls with a NULL udev pointer in drivers/gpio/sunxi_gpio.c
this adds are removed in a later patch.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

show more ...

Merge branch 'master' of http://git.denx.de/u-boot-sunxi

sunxi: axp221: Use vbus-available rather then vbus-usable for vbus-detect

vbus-usable may not get set if power is provided through both the power barrel
connector and external 5v is also present on

sunxi: axp221: Use vbus-available rather then vbus-usable for vbus-detect

vbus-usable may not get set if power is provided through both the power barrel
connector and external 5v is also present on the otg connector, at least on
boards where vbus is also controlled through the axp221-pmic.

One way to reproduce this is to bootup an Ippo-q8h board with a usb-host
cable plugged into the otg (so that it will get powered), then unplug the
usb-host cable and plug in a charger, and then do "reset" on the u-boot
console, vbus-usable will then report 0, leading to uboot trying to provide
power to the otg port even though external 5v is present, this commit fixes
this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

show more ...

power: axp221: Virtual VBUS detect and enable GPIOs to replace separate logic

This converts the VBUS detection and enable logic to GPIO instead of separate
axp functions and checks that have to be u

power: axp221: Virtual VBUS detect and enable GPIOs to replace separate logic

This converts the VBUS detection and enable logic to GPIO instead of separate
axp functions and checks that have to be used aside usual GPIO functions.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

show more ...

sunxi: axp221: Add VBUS detection support

Some of the AXP PMICs support VBUS detection, i.e. checking whether
VBUS power input is available and usable (supplied by an external
source). A few boards

sunxi: axp221: Add VBUS detection support

Some of the AXP PMICs support VBUS detection, i.e. checking whether
VBUS power input is available and usable (supplied by an external
source). A few boards use this instead of a separate GPIO to detect
VBUS on USB OTG.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

show more ...

Merge remote-tracking branch 'u-boot/master' into 'u-boot-arm/master'

Merge branch 'master' of git://git.denx.de/u-boot

Merge branch 'master' of git://git.denx.de/u-boot-sunxi

sunxi: rsb: Move rsb_set_device_mode() call to rsb_init()

It turns out that the device_mode_data is rsb specific, rather then slave
specific, so integrate the rsb_set_device_mode() call into rsb_ini

sunxi: rsb: Move rsb_set_device_mode() call to rsb_init()

It turns out that the device_mode_data is rsb specific, rather then slave
specific, so integrate the rsb_set_device_mode() call into rsb_init().

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

show more ...