Merge git://git.denx.de/u-boot-marvell

- Multiples updates to the turris boards / platform
- Changes / enhancements to the Marvell PHY drivers, mainly
to support the turris platform
- Many fixes a

Merge git://git.denx.de/u-boot-marvell

- Multiples updates to the turris boards / platform
- Changes / enhancements to the Marvell PHY drivers, mainly
to support the turris platform
- Many fixes and enhancements to the pxa3xx NAND driver
- Fixes for the UART boot mode in kwboot
- Misc minor changes to other 32bit and 64bit boards

show more ...

phy: marvell: add SATA comphy RX/TX polarity invert support

This patch adds support to Armada 7k/8k comphy RX/TX lane swap. The
'phy-invert' DT property defines the inverted signals.

Signed-off-by:

phy: marvell: add SATA comphy RX/TX polarity invert support

This patch adds support to Armada 7k/8k comphy RX/TX lane swap. The
'phy-invert' DT property defines the inverted signals.

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>

show more ...

phy: marvell: Support changing SERDES map in board file

This adds a weak definition of comphy_update_map to comphy_core,
which does nothing. If this function is defined elsewhere, for example
in boa

phy: marvell: Support changing SERDES map in board file

This adds a weak definition of comphy_update_map to comphy_core,
which does nothing. If this function is defined elsewhere, for example
in board file, the board file can change some parameters of SERDES
configuration.

This is needed on Turris Mox, where the SERDES speed on lane 1 has to
be set differently when SFP module is connected and when Topaz Switch
module is connected.

This is a temporary solution. When the comphy driver for armada-3720
will be added to the kernel, the comphy driver in u-boot shall also be
updated and this should be done differently then.

Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>

show more ...

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

treewide: replace with error() with pr_err()

U-Boot widely uses error() as a bit noisier variant of printf().

This macro causes name conflict with the following line in
include/linux/compiler-gcc.h

treewide: replace with error() with pr_err()

U-Boot widely uses error() as a bit noisier variant of printf().

This macro causes name conflict with the following line in
include/linux/compiler-gcc.h:

# define __compiletime_error(message) __attribute__((error(message)))

This prevents us from using __compiletime_error(), and makes it
difficult to fully sync BUILD_BUG macros with Linux. (Notice
Linux's BUILD_BUG_ON_MSG is implemented by using compiletime_assert().)

Let's convert error() into now treewide-available pr_err().

Done with the help of Coccinelle, excluing tools/ directory.

The semantic patch I used is as follows:

// <smpl>
@@@@
-error
+pr_err
(...)
// </smpl>

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Re-run Coccinelle]
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Merge git://www.denx.de/git/u-boot-marvell

fix: phy: marvell: cp110: pcie: update analog parameters according to latest ETP

Add PCIE analog parameters initialization values according to
latest ETP.

Signed-off-by: Igal Liberman <igall@marvel

fix: phy: marvell: cp110: pcie: update analog parameters according to latest ETP

Add PCIE analog parameters initialization values according to
latest ETP.

Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>

show more ...

fix: phy: marvell: cp110: rename comphy_index to cp_index

No functional change.
The variable name "comphy_index" is misleading, it represents
cp index and not comphy index.

Signed-off-by: Igal Libe

fix: phy: marvell: cp110: rename comphy_index to cp_index

No functional change.
The variable name "comphy_index" is misleading, it represents
cp index and not comphy index.

Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>

show more ...

fix: phy: marvell: cp110: sfi: update analog parameters according to latest ETP

Add SFI analog parameters initialization values according to
latest ETP.

Signed-off-by: Igal Liberman <igall@marvell.

fix: phy: marvell: cp110: sfi: update analog parameters according to latest ETP

Add SFI analog parameters initialization values according to
latest ETP.

Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>

show more ...

fix: phy: marvell: cp110: fix comphy lane 4 selection options

The comphy configuration is incorrect.
Set the correct values for SGMII.

In addition, remove xaui from the comment as it is not support

fix: phy: marvell: cp110: fix comphy lane 4 selection options

The comphy configuration is incorrect.
Set the correct values for SGMII.

In addition, remove xaui from the comment as it is not supported.

Signed-off-by: Yoav Gvili <ygvili@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>

show more ...

phy: marvell: cp110: add 5G XFI mode

This patch adds the option to configure a comphy to 5G XFI mode.

In order to configure the comphy to 5G XFI, update
the comphy node in the device-tree:
phy2 {

phy: marvell: cp110: add 5G XFI mode

This patch adds the option to configure a comphy to 5G XFI mode.

In order to configure the comphy to 5G XFI, update
the comphy node in the device-tree:
phy2 {
phy-type = <PHY_TYPE_SFI>;
phy-speed = <PHY_SPEED_5_15625G>;
};

Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>

show more ...

fix: phy: marvell: cp110: update comphy selector option

Align PHY selectors register with Armada-CP-110 functional SPEC
update all relevant device trees with this change.

Signed-off-by: Hanna Hawa

fix: phy: marvell: cp110: update comphy selector option

Align PHY selectors register with Armada-CP-110 functional SPEC
update all relevant device trees with this change.

Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>

show more ...

fix: phy: marvell: cp110: sata: update analog parameters according to latest ETP

Add SATA analog parameters initialization values according to
latest ETP.

Signed-off-by: Konstantin Porotchkin <kost

fix: phy: marvell: cp110: sata: update analog parameters according to latest ETP

Add SATA analog parameters initialization values according to
latest ETP.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>

show more ...

fix: phy: marvell: cp110: fix the KR/SFI line 4 selector

This patch fixes the following:
1. KR/SFI on lane #4 mux selector is 0x2 and not 0x1
2. Comment typo

Signed-off-by: Rabeeh Khoury <rabeeh@so

fix: phy: marvell: cp110: fix the KR/SFI line 4 selector

This patch fixes the following:
1. KR/SFI on lane #4 mux selector is 0x2 and not 0x1
2. Comment typo

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>

show more ...

phy: marvell: add IGNORE COMPHY type

This type tells u-boot to preserve the COMPHY settings as is
it is usefull in situations where the COMPHY was initialized by
earlier firmware.
Note that IGNORE i

phy: marvell: add IGNORE COMPHY type

This type tells u-boot to preserve the COMPHY settings as is
it is usefull in situations where the COMPHY was initialized by
earlier firmware.
Note that IGNORE is different from UNCONNECTED since setting
UNCONNECTED type will disconnect the COMPHY in the COMPHY MUX
which is a desired behaviour

Signed-off-by: Yehuda Yitschak <yehuday@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>

show more ...

phy: marvell: cp110: update utmi phy connection type

UTMI_PHY_TO_USB_HOST was used in USB3 UTMI dts node only, but there will
be USB2 UTMI dts node for some SoCs that have got USB2 controller, so re

phy: marvell: cp110: update utmi phy connection type

UTMI_PHY_TO_USB_HOST was used in USB3 UTMI dts node only, but there will
be USB2 UTMI dts node for some SoCs that have got USB2 controller, so rename
TO_USB_HOST to TO_USB3_HOST to distinguish TO_USB2_HOST in later on patches.

Signed-off-by: zachary <zhangzg@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>

show more ...

phy: marvell: cp110: add support for end point configuration

The serdes was always configured in root complex mode.
this patch add new entry in device tree (per serdes)
which indicates whether the s

phy: marvell: cp110: add support for end point configuration

The serdes was always configured in root complex mode.
this patch add new entry in device tree (per serdes)
which indicates whether the serdes is in end point mode.
if so, it skips the root complex configuration.

Signed-off-by: Haim Boot <hayim@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>

show more ...

phy: marvell: Replace PHY_TYPE_KR with PHY_TYPE_SFI

Use correct naming as done in the latest Marvell U-Boot version as well.

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <i

phy: marvell: Replace PHY_TYPE_KR with PHY_TYPE_SFI

Use correct naming as done in the latest Marvell U-Boot version as well.

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>

show more ...

Merge git://www.denx.de/git/u-boot-marvell

drivers/phy: Add Marvell SerDes / PHY drivers used on Armada 7K/8K

This version is based on the Marvell U-Boot version with this patch
applied as latest patch:

Git ID 7f408573: "fix: comphy: cp110:

drivers/phy: Add Marvell SerDes / PHY drivers used on Armada 7K/8K

This version is based on the Marvell U-Boot version with this patch
applied as latest patch:

Git ID 7f408573: "fix: comphy: cp110: add comphy initialization for usb
device mode" from 2016-07-05.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>

show more ...