Merge branch 'master' of git://git.denx.de/u-boot

Signed-off-by: Stefano Babic <sbabic@denx.de>

Merge branch '2019-03-29-master-imports'

- Bugfixes:
- mmc: correct the HS400 initialization process
- configs: ti: Move FIT image load address to avoid overwrite
- lib: time: update module en

Merge branch '2019-03-29-master-imports'

- Bugfixes:
- mmc: correct the HS400 initialization process
- configs: ti: Move FIT image load address to avoid overwrite
- lib: time: update module enable MACRO
- Add mbrugger as RPi board maintainer, correct agraf's email address.

show more ...

mmc: correct the HS400 initialization process

After the commit b9a2a0e2e9c0 ("mmc: Add support for downgrading
HS200/HS400 to HS mode"), it add a parameter in mmc_set_card_speed()
which indicates th

mmc: correct the HS400 initialization process

After the commit b9a2a0e2e9c0 ("mmc: Add support for downgrading
HS200/HS400 to HS mode"), it add a parameter in mmc_set_card_speed()
which indicates that the HS200/HS400 to HS downgrade is happening.

During the HS400 initialization, first select to HS200, and config
the related clock rate, then downgrade to HS mode. So here also need
to config the downgrade value to be true for two reasons. First,
make sure in the function mmc_set_card_speed(), after switch to HS
mode, first config the clock rate, then read the EXT_CSD, avoid
receiving data of EXT_CSD in HS mode at 200MHz. Second, after issue
the MMC_CMD_SWITCH command, it need to wait a bit then switch bus
properties.

Test on i.MX8QM MEK board, some Micron eMMC will stuck in transfer
mode in this case, and USDHC will never get data transfer complete
status, cause the uboot hang.

Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>

show more ...

Merge branch '2019-03-25-master-imports'

- 3 bugfixes:
- mmc: Align MMC_TRACE with tiny printf
- scripts/Makefile.extrawarn: Silence more DTC warnings
- rsa: check that pointer checksum isn't

Merge branch '2019-03-25-master-imports'

- 3 bugfixes:
- mmc: Align MMC_TRACE with tiny printf
- scripts/Makefile.extrawarn: Silence more DTC warnings
- rsa: check that pointer checksum isn't NULL before using it

show more ...

mmc: Align MMC_TRACE with tiny printf

The tiny printf implementation only supports %x format specifier,
it does not support %X . Since it makes little difference whether
the debug output prints hex

mmc: Align MMC_TRACE with tiny printf

The tiny printf implementation only supports %x format specifier,
it does not support %X . Since it makes little difference whether
the debug output prints hex numbers in capitals or not, change it
to %x and make the MMC_TRACE output work with tiny printf too.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Simon Glass <sjg@chromium.org>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-sh

- Various MMC fixes

mmc: Downgrade SD/MMC from UHS/HS200/HS400 modes before boot

Older kernel versions or systems which do not connect eMMC reset line
properly may not be able to handle situations where either the eMMC

mmc: Downgrade SD/MMC from UHS/HS200/HS400 modes before boot

Older kernel versions or systems which do not connect eMMC reset line
properly may not be able to handle situations where either the eMMC
is left in HS200/HS400 mode or SD card in UHS modes by the bootloader
and may misbehave. Downgrade the eMMC to HS/HS52 mode and/or SD card
to non-UHS mode before booting the kernel to allow such older kernels
to work with modern U-Boot.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-sh

- SD/MMC fixes and ext4 memory leak fix

mmc: Do not poll using CMD13 when changing timing

When using CMD6 to switch eMMC card timing from HS200/HS400 to HS/legacy,
do not poll for the completion status using CMD13, but rather wait 50mS.

mmc: Do not poll using CMD13 when changing timing

When using CMD6 to switch eMMC card timing from HS200/HS400 to HS/legacy,
do not poll for the completion status using CMD13, but rather wait 50mS.

Once the card receives the CMD6 and starts executing it, the bus is in
undefined state until both the card finishes executing the command and
until the controller switches the bus to matching timing configuration.
During this time, it is not possible to transport any commands or data
across the bus, which includes the CMD13.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>

show more ...

Merge branch '2019-01-14-master-imports'

- MediaTek improvements (eth support)
- DM conversion for HI6220
- ISEE, Toby Churchill, other platform updates
- Various format code printf fixes
- Build ra

Merge branch '2019-01-14-master-imports'

- MediaTek improvements (eth support)
- DM conversion for HI6220
- ISEE, Toby Churchill, other platform updates
- Various format code printf fixes
- Build race fixes
- Command repeat functionality enhanced, command autocomplete support
enhanced.

show more ...

mmc: Add support for downgrading HS200/HS400 to HS mode

The mmc_select_mode_and_width() function can be called while the card
is in HS200/HS400 mode and can be used to downgrade the card to lower
mo

mmc: Add support for downgrading HS200/HS400 to HS mode

The mmc_select_mode_and_width() function can be called while the card
is in HS200/HS400 mode and can be used to downgrade the card to lower
mode, e.g. HS. This is used for example by mmc_boot_part_access_chk()
which cannot access the card in HS200/HS400 mode and which is in turn
called by saveenv if env is in the MMC.

In such case, forcing the card clock to legacy frequency cannot work.
Instead, the card must be switched to HS mode first, from which it can
then be reprogrammed as needed.

However, this procedure needs additional code changes, since the current
implementation checks whether the card correctly switched to HS mode in
mmc_set_card_speed(). The check only expects that the card will be going
to HS mode from lower modes, not from higher modes, hence add a parameter
which indicates that the HS200/HS400 to HS downgrade is happening. This
makes the code send the switch command first, reconfigure the controller
next and finally perform the EXT_CSD readback check. The last two steps
cannot be done in reverse order as the card is already in HS mode when
the clock are being switched on the controller side.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>

show more ...

Merge branch '2019-01-08-master-imports'

- stm32f7 GPIO fixes
- SATA env fixes
- More DM migration deadline warnings
- Regression fix for non-DM MMC drivers
- dma_alloc_coherent size fix on ARM.

mmc: bring back partition init for non-DM MMC drivers

Commit d0851c893706 ("blk: Call part_init() in the post_probe() method")
removed the call to part_init() in mmc.c, as this is done by the DM_MMC

mmc: bring back partition init for non-DM MMC drivers

Commit d0851c893706 ("blk: Call part_init() in the post_probe() method")
removed the call to part_init() in mmc.c, as this is done by the DM_MMC
framework.
However Allwinner is (still) relying on a non-DM MMC driver, so we are
now missing the implicit partition init, leading to failing MMC accesses
due to the missing partition information.

Bring the call back just for non-DM MMC driver to fix this regression.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Soeren Moch <smoch@web.de>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-sh

- DT sync with Linux 4.19 and minor fixes.

mmc: Do not issue CMD 6 on SD 1.00 and SD 1.01

According to SD Specifications Part 1 Physical Layer Simplified Specification
Version 6.00 August 29, 2018, section 4.3.10 (Switch Function Command) an

mmc: Do not issue CMD 6 on SD 1.00 and SD 1.01

According to SD Specifications Part 1 Physical Layer Simplified Specification
Version 6.00 August 29, 2018, section 4.3.10 (Switch Function Command) and
section 5.6 (SCR register), SD cards version 1.00 and 1.01 do not support the
SD CMD 6.

Currently, U-Boot will issue CMD 6 unconditionally in sd_set_card_speed()
while configuring the bus for selected frequency. This will make SD cards
version 1.00 and 1.01 time out and thus fail detection altogether.

Fix this by not sending CMD 6 on such cards. Tested on Matsushita Electric
Industrial Co., Ltd. Japan RP-SD008B / Victor 8MB SD card, CU-SD008, which
is correctly detected with this patch as:

Device: sd@ee160000
Manufacturer ID: 1
OEM: 5041
Name: S008B
Bus Speed: 25000000
Mode : SD Legacy
Rd Block Len: 512
SD version 1.0
High Capacity: No
Capacity: 6.5 MiB
Bus Width: 4-bit
Erase Group Size: 512 Bytes

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>

show more ...

Merge tag 'pull-14nov18' of git://git.denx.de/u-boot-dm

- virtio implementation and supporting patches
- DM_FLAG_PRE_RELOC fixes
- regmap improvements
- minor buildman and sandbox things

blk: Call part_init() in the post_probe() method

part_init() is currently called in every DM BLK driver, either
in its bind() or probe() method. However we can use the BLK
uclass driver's post_probe

blk: Call part_init() in the post_probe() method

part_init() is currently called in every DM BLK driver, either
in its bind() or probe() method. However we can use the BLK
uclass driver's post_probe() method to do it automatically.

Update all DM BLK drivers to adopt this change.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

show more ...

mmc: add HS400 support

Add HS400 support.
Selecting HS400 needs first select HS200 according to spec, so use
a dedicated function for HS400.
Add HS400 related macros.
Remove the restriction of only

mmc: add HS400 support

Add HS400 support.
Selecting HS400 needs first select HS200 according to spec, so use
a dedicated function for HS400.
Add HS400 related macros.
Remove the restriction of only using the low 6 bits of
EXT_CSD_CARD_TYPE, using all the 8 bits.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-imx

trini: Update colibri-imx6ull to use Kconfig for mtdparts related
options.

Signed-off-by: Tom Rini <trini@konsulko.com>

mmc: break out get_op_cond code to its own function

This code is useful for testing the existance of devices that
do not have card detect capabilities. This breaks out the core
functionality and le

mmc: break out get_op_cond code to its own function

This code is useful for testing the existance of devices that
do not have card detect capabilities. This breaks out the core
functionality and leaves the actual init logic and error reporting
in mmc_start_init().

Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefano Babic <sbabic@denx.de>

show more ...

mmc: Improve tinification

Drop all the extra content from the MMC core, so that tiny MMC support
is really tiny, no fancy anything. That means the tiny MMC support does
only 1-bit transfers at defau

mmc: Improve tinification

Drop all the extra content from the MMC core, so that tiny MMC support
is really tiny, no fancy anything. That means the tiny MMC support does
only 1-bit transfers at default speed settings. Moreover, this patch
drops duplicate instance of struct mmc mmc_static, which wasted about
360 bytes. Furthermore, since MMC tiny supports only one controller
at all times, get rid of mallocating the ext csd backup and replace
it with static array. All in all, this patch saves ~4 kiB of bloat
from the MMC core, which on platforms with severe limitations can be
beneficial.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Fixup checkpatch.pl style warnings]
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Merge tag 'xilinx-for-v2018.07' of git://www.denx.de/git/u-boot-microblaze

Xilinx changes for v2018.07

microblaze:
- Align defconfig

zynq:
- Rework fpga initialization and cpuinfo handling

zynqmp

Merge tag 'xilinx-for-v2018.07' of git://www.denx.de/git/u-boot-microblaze

Xilinx changes for v2018.07

microblaze:
- Align defconfig

zynq:
- Rework fpga initialization and cpuinfo handling

zynqmp:
- Add ZynqMP R5 support
- Wire and enable watchdog on zcu100-revC
- Setup MMU map for DDR at run time
- Show board info based on DT and cleanup IDENT_STRING

zynqmp tools:
- Add read partition support
- Add initial support for Xilinx bif format for boot.bin generation

mmc:
- Fix get_timer usage on 64bit cpus
- Add support for SD3.0 UHS mode

nand-zynq:
- Add support for 16bit buswidth
- Use address cycles from onfi params

scsi:
- convert ceva sata to UCLASS_AHCI

timer:
- Add Cadence TTC for ZynqMP r5

watchdog:
- Minor cadence driver cleanup

show more ...

mmc: Changed the datatype of the variable to handle 64-bit arch

This patch changed the datatype of variable "start" from uint to ulong
to work properly on 64-bit machines as well. Also the return ty

mmc: Changed the datatype of the variable to handle 64-bit arch

This patch changed the datatype of variable "start" from uint to ulong
to work properly on 64-bit machines as well. Also the return type of
get_timer() function is ulong.

Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

show more ...

Merge git://git.denx.de/u-boot-mmc

mmc: add the debug message in mmc_set_clock

Add the debug message for checking the mmc clock status.
It's helpful to debug the controlling clock.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.co

mmc: add the debug message in mmc_set_clock

Add the debug message for checking the mmc clock status.
It's helpful to debug the controlling clock.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>

show more ...