Merge tag 'u-boot-imx-20181025' of git://git.denx.de/u-boot-imx

Merged imx8 architecture, fix build for imx8 + warnings

i2c: imx_lpi2c: fix typo and register base address format

Output the register base address in hex notation.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>

Merge branch 'agust@denx.de' of git://git.denx.de/u-boot-staging

i2c: imx_lpi2c: add uclass api support

Use uclass clk api to get per clk when CONFIG_CLK enabled.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>

Merge branch 'master' of git://git.denx.de/u-boot-i2c

lpi2c: Add bus busy error handling

When doing "i2c dev 4; i2c probe" with ENET daughter card connected
on iMX8QXP MEK board, we met a i2c bus busy issue, that the BBF of
lpi2c always show busy, but

lpi2c: Add bus busy error handling

When doing "i2c dev 4; i2c probe" with ENET daughter card connected
on iMX8QXP MEK board, we met a i2c bus busy issue, that the BBF of
lpi2c always show busy, but the master is idle, and stop is detected
(SDF set).

This patch addes a handling to re-init the lpi2c master for this
case. Then the issue can be worked around.

Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Heiko Schocher <hs@denx.de>

show more ...

lpi2c: Fix bus stop problem in xfer

In xfer function, both bus_i2c_read and bus_i2c_write will
send a STOP command. This causes a problem when reading register
data from i2c device.

Generally two

lpi2c: Fix bus stop problem in xfer

In xfer function, both bus_i2c_read and bus_i2c_write will
send a STOP command. This causes a problem when reading register
data from i2c device.

Generally two operations comprise the register data reading:
1. Write the register address to i2c device.
START | chip_addr | W | ACK | register_addr | ACK |

2. Read the Data from i2c device.
START | chip_addr | R | ACK | DATA | NACK | STOP

The STOP command should happen at the end of the transfer, otherwise
we will always get data from register address 0

Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Heiko Schocher <hs@denx.de>

show more ...

imx: lpi2c: fix clock issue when NACK detected

For LPI2C IP, NACK is detected by the rising edge of the ninth clock.
In current uboot driver, once NACK is detected, it will reset and then
disable LP

imx: lpi2c: fix clock issue when NACK detected

For LPI2C IP, NACK is detected by the rising edge of the ninth clock.
In current uboot driver, once NACK is detected, it will reset and then
disable LPI2C master. As a result, we can never see the falling edge
of the ninth clock.

Signed-off-by: Gao Pan <pandy.gao@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Heiko Schocher <hs@denx.de>

show more ...

imx_lpi2c: Update lpi2c driver to support imx8

Add compatible string for i.MX8 and move imx_lpi2c.h from mx7ulp directory
to u-boot include directory as a common header file.

Signed-off-by: Ye Li <

imx_lpi2c: Update lpi2c driver to support imx8

Add compatible string for i.MX8 and move imx_lpi2c.h from mx7ulp directory
to u-boot include directory as a common header file.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Heiko Schocher <hs@denx.de>

show more ...

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Remove unnecessary instances of DECLARE_GLOBAL_DATA_PTR

We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added

Remove unnecessary instances of DECLARE_GLOBAL_DATA_PTR

We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.

Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Merge git://git.denx.de/u-boot-i2c

i2c: lpi2c: remove superfluous assignments

In

lpi2c_status_t result = A;
result = B;

the first assignment has no effect. Let's remove it.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

Merge git://git.denx.de/u-boot-i2c

i2c: lpi2c: do not add 4 for bus seq

The number 4 is dedicated on i.MX7ULP, but lpi2c will be reused on i.MX8,
4 is not valid. The seq number could be configured by alias node.

The following patch

i2c: lpi2c: do not add 4 for bus seq

The number 4 is dedicated on i.MX7ULP, but lpi2c will be reused on i.MX8,
4 is not valid. The seq number could be configured by alias node.

The following patch will use i2c4 as the begin for i.MX7ULP.

Signed-off-by: Peng Fan <peng.fan@nxp.com>

show more ...

Merge git://git.denx.de/u-boot-dm

dm: gpio: Correct use of -ENODEV in drivers

In U-Boot -ENODEV means that there is no device. When there is a problem
with the device, drivers should return an error like -ENXIO or -EREMOTEIO.
When t

dm: gpio: Correct use of -ENODEV in drivers

In U-Boot -ENODEV means that there is no device. When there is a problem
with the device, drivers should return an error like -ENXIO or -EREMOTEIO.
When the device tree properties cannot be read correct , they should
return -EINVAL.

Update various GPIO drivers to follow this rule, to help with consistency
for future driver writers.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Adam Ford <aford173@gmail.com>

show more ...

dm: Rename dev_addr..() functions

These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing function

dm: Rename dev_addr..() functions

These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing functions to avoid confusion.

In the end we will have:

1. dev_read_addr...() - works on devices, supports flat/live tree
2. devfdt_get_addr...() - current functions, flat tree only
3. of_get_address() etc. - new functions, live tree only

All drivers will be written to use 1. That function will in turn call
either 2 or 3 depending on whether the flat or live tree is in use.

Note this involves changing some dead code - the imx_lpi2c.c file.

Signed-off-by: Simon Glass <sjg@chromium.org>

show more ...

Merge branch 'master' of git://www.denx.de/git/u-boot-imx

Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
configs/bk4r1_defconfig
configs/colibri_vf_defconfig
configs/pcm052_defconfig
i

Merge branch 'master' of git://www.denx.de/git/u-boot-imx

Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
configs/bk4r1_defconfig
configs/colibri_vf_defconfig
configs/pcm052_defconfig
include/configs/colibri_vf.h
include/configs/pcm052.h

show more ...

i2c: lpi2c: add lpi2c driver for i.MX7ULP

Add lpi2c driver for i.MX7ULP.
Need to enable the two options to use this driver:
CONFIG_DM_I2C=y
CONFIG_SYS_I2C_IMX_LPI2C=y

Signed-off-by: Peng Fan <peng.

i2c: lpi2c: add lpi2c driver for i.MX7ULP

Add lpi2c driver for i.MX7ULP.
Need to enable the two options to use this driver:
CONFIG_DM_I2C=y
CONFIG_SYS_I2C_IMX_LPI2C=y

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Stefano Babic <sbabic@denx.de>

show more ...