Merge tag 'xilinx-for-v2019.04' of git://git.denx.de/u-boot-microblaze

Xilinx changes for v2019.04

tools:
- Fix zynqmpimage generation

zynq:
- Some configs/Kconfig/DT updates
- Enable REMAKE_ELF a

Merge tag 'xilinx-for-v2019.04' of git://git.denx.de/u-boot-microblaze

Xilinx changes for v2019.04

tools:
- Fix zynqmpimage generation

zynq:
- Some configs/Kconfig/DT updates
- Enable REMAKE_ELF and OF_SEPARATE
- Topic boards update
- i2c cleanups and conversion to DM_I2C

zynqmp:
- Some configs/Kconfig/DT updates
- Board config cleanup
- Move arch folder to mach-zynqmp

versal:
- Enable DM_I2C, CMD_DM

zynq-gem:
- Fix driver cache handling

i2c:
- Live tree simple update

phy:
- Fixed phy cleanup

travis:
- Wire Versal SoC

show more ...

arm64: zynqmp: Setup DM_ETH/MMC if NET/MMC is enabled

Setup proper ETH/MMC dependency for the whole platform.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Merge tag 'xilinx-for-v2019.01' of git://git.denx.de/u-boot-microblaze

Xilinx changes for v2019.01

microblaze:
- Use default functions for memory decoding
- Showing model from DT

zynq:
- Fix spi f

Merge tag 'xilinx-for-v2019.01' of git://git.denx.de/u-boot-microblaze

Xilinx changes for v2019.01

microblaze:
- Use default functions for memory decoding
- Showing model from DT

zynq:
- Fix spi flash DTs
- Fix zynq_help_text with CONFIG_SYS_LONGHELP
- Tune cse/mini configurations
- Enabling cse/mini testing with current targets

zynqmp:
- Enable gzip SPL support
- Fix chip detection logic
- Tune mini configurations
- DT fixes(spi-flash, models, clocks, etc)
- Add support for OF_SEPARATE configurations
- Enabling mini testing with current targets
- Add mini mtest configuration
- Some minor config setting

nand:
- arasan: Add subpage configuration

net:
- gem: Add 64bit DMA support

show more ...

arm64: zynqmp: Wire mini-emmc0 configuration with zcu100

For testing purpose use zcu100 which has SD at controller 0 and this can
be used for testing this mini configuration.

U-Boot 2018.11-00281-g

arm64: zynqmp: Wire mini-emmc0 configuration with zcu100

For testing purpose use zcu100 which has SD at controller 0 and this can
be used for testing this mini configuration.

U-Boot 2018.11-00281-gc5d48466e76e (Nov 30 2018 - 10:41:05 +0100)

Model: ZynqMP MINI EMMC0
Board: Xilinx ZynqMP
DRAM: 512 MiB
EL Level: EL3
MMC: sdhci@ff160000: 0
In: dcc
Out: dcc
Err: dcc
ZynqMP>

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

show more ...

arm64: zynqmp: Use minimal size for environment variables

There is no reason to have huge space for variables because none is
using that. But there are some which are setup automatically.

baudrate=

arm64: zynqmp: Use minimal size for environment variables

There is no reason to have huge space for variables because none is
using that. But there are some which are setup automatically.

baudrate=115200
fdtcontroladdr=ffffa0d0
stderr=dcc
stdin=dcc
stdout=dcc

Environment size: 72/124 bytes

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

show more ...

arm64: zynqmp: Do not save variables about board

No reason to save this data to environment.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Disable autoboot feature for mini

There is no reason to have autoboot enabled because it should never
start anything automatically.

Signed-off-by: Michal Simek <michal.simek@xilinx.c

arm64: zynqmp: Disable autoboot feature for mini

There is no reason to have autoboot enabled because it should never
start anything automatically.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

show more ...

arm64: zynqmp: Disable bootelf and fdt commands for mini configurations

There is no reason to enable these commands for mini configurations.
It saves some space:
aarch64: (for 2/2 boards) all -19

arm64: zynqmp: Disable bootelf and fdt commands for mini configurations

There is no reason to enable these commands for mini configurations.
It saves some space:
aarch64: (for 2/2 boards) all -19076.0 bss -1048.0 data -1720.0
rodata -3840.0 text -12468.0
xilinx_zynqmp_mini_emmc1: all -19076 bss -1048 data -1720
rodata -3840 text -12468
xilinx_zynqmp_mini_emmc0: all -19076 bss -1048 data -1720
rodata -3840 text -12468

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

show more ...

Merge git://git.denx.de/u-boot-microblaze

Xilinx changes for v2018.11-rc2-v2

FPGA:
- Fix SPL fpga loading from FIT

ARM64:
- Fix gic accesses in EL2/EL1

Xilinx:
- Add dlc20 board support
- Add Ver

Merge git://git.denx.de/u-boot-microblaze

Xilinx changes for v2018.11-rc2-v2

FPGA:
- Fix SPL fpga loading from FIT

ARM64:
- Fix gic accesses in EL2/EL1

Xilinx:
- Add dlc20 board support
- Add Versal board support
- Sync defconfigs
- Enable MP via Kconfig
- Add missing efuse node
- Enable CDC for zcu100

cmd:
- Fix kgdb Kconfig dependency

show more ...

arm64: zynqmp: Enable MP by default via Kconfig

Simplify defconfig for ZynqMP but keep option not to enable it for mini
targets.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Merge tag 'xilinx-for-v2018.11' of git://git.denx.de/u-boot-microblaze

Xilinx changes for v2018.11

- Handle BOARD_LATE_INIT via Kconfig

SPL:
- Enable GZIP for all partitions types(not only for ker

Merge tag 'xilinx-for-v2018.11' of git://git.denx.de/u-boot-microblaze

Xilinx changes for v2018.11

- Handle BOARD_LATE_INIT via Kconfig

SPL:
- Enable GZIP for all partitions types(not only for kernel)

ZynqMP:
- Rearrange pmufw version handling
- Support newer PMUFW with improved fpga load sequence

Zynq:
- Cleanup config file
- Simplify zybo config by enabling option via Kconfig

net:
- Fix gems max-speed property reading
- Enable support for fixed-link phys

show more ...

arm64: zynqmp: Handle CONFIG_BOARD_LATE_INIT via Kconfig

Disable BOARD_LATE_INIT via Kconfig.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CONFIG_NR_DRAM_BANKS

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANK

configs: Migrate CONFIG_NR_DRAM_BANKS

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Merge tag 'xilinx-for-v2018.09' of git://git.denx.de/u-boot-microblaze

Xilinx changes for v2018.09

clk:
- Fix zynqmp clock driver

common:
- Handle CMD_RET_USAGE in cmd_process_error
- Use return m

Merge tag 'xilinx-for-v2018.09' of git://git.denx.de/u-boot-microblaze

Xilinx changes for v2018.09

clk:
- Fix zynqmp clock driver

common:
- Handle CMD_RET_USAGE in cmd_process_error
- Use return macros in cmd_process_error
- Fix duplication of CONFIG_SYS_PROMPT_HUSH_PS2
- Support watchdog in usb_kbd.c
- Fix name usage in usb_kbd.c
- Support systems with non zero memory start initialized from DT only

gpio:
- Add support for manual relocation in uclass
- zynq - use live tree
- zynq - fix match data reading
- zynq - setup bank name
- xilinx - convert driver to DM

microblaze:
- Use generic iounmap/ioremap implementations
- Redesign reset logic with sysreset features
- Use watchdog and gpio over DM
- Remove unused macros and fix some checkpatch issues
- Fix timer initialization not to be called twice

serial:
- zynq - Use platdata intead of priv data

sysreset:
- Add support for manual relocation in uclass
- Add gpio-restart driver
- Add microblaze soft reset driver

watchdog:
- Add support for aliases in uclass
- Add support for manual relocation in uclass
- Convert xilinx driver to DM
- cadence - update info in the driver and not stop wdt in probe

xilinx:
- Enable LED gpio for some targets with gpio-leds DT node
- Setup variables via Kconfig

zynq:
- Add support for watchdog aliases
- Add support for mini nand/nor configurations
- Wire FPGA initalization in SPL

zynqmp:
- Enable mass storage for zcu100
- Handle external pmufw files
- Add support for secure images
- Some Kconfig movements and alignments
- Add support for watchdog aliases
- Use subcommands style for platform command
- Add mmio_read/write platform commands
- DT updates
- Add support for mini qspi configuration

show more ...

arm64: zynqmp: Setup ENV_SIZE via Kconfig for mini targets

Mini targets are using different ENV_SIZE then standard one that's why
defconfigs should be updated to simplify config files.

Signed-off-b

arm64: zynqmp: Setup ENV_SIZE via Kconfig for mini targets

Mini targets are using different ENV_SIZE then standard one that's why
defconfigs should be updated to simplify config files.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

show more ...

Merge tag 'xilinx-for-v2018.07-rc2' of git://git.denx.de/u-boot-microblaze

Xilinx fixes for v2018.07-rc2

Zynq:
- Fix missing watchdog header
- DT fixes

ZynqMP:
- emmc configuration split
- Enable

Merge tag 'xilinx-for-v2018.07-rc2' of git://git.denx.de/u-boot-microblaze

Xilinx fixes for v2018.07-rc2

Zynq:
- Fix missing watchdog header
- DT fixes

ZynqMP:
- emmc configuration split
- Enable SPD
- Fix PMUFW_INIT_FILE logic
- Coverity fixes in SoC code

timer
- Add timer_get_boot_us

mmc:
- Fix MMC HS200 tuning command

serial:
- Fix scrabled chars with OF_LIVE

show more ...

arm64: zynqmp: Split emmc configuration into emmc0 and emmc1

This patch splits the current mini emmc configuration into emmc0
and emmc1 configurations because emmc is probed at boot time and on
syst

arm64: zynqmp: Split emmc configuration into emmc0 and emmc1

This patch splits the current mini emmc configuration into emmc0
and emmc1 configurations because emmc is probed at boot time and on
systems which have only one interface mini configuration is failing on
unused interface. This patch also adds required clock node in dts and
enables CONFIG_MMC_SDHCI_ZYNQ through defconfig.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

show more ...