Add Beaglebone Enhanced support

The "Beaglebone Enhanced" by Sancloud is based on the Beaglebone Black,
but with the following differences:

* Gigabit capable PHY
* Extra USB hub, optional i2c con

Add Beaglebone Enhanced support

The "Beaglebone Enhanced" by Sancloud is based on the Beaglebone Black,
but with the following differences:

* Gigabit capable PHY
* Extra USB hub, optional i2c control
* lps3331ap barometer connected over i2c
* MPU6050 6 axis MEMS accelerometer/gyro connected over i2c
* 1GiB DDR3 RAM
* RTL8723 Wifi/Bluetooth connected over USB

Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Add support for BeagleBoard.org PocketBeagle

Texas Instruments AM3358 based low-cost board using Octavo Systems OSD3358 SIP
with built-in TPS65217 PMIC and 512MB DDR3. Board features small 35mm x
55

Add support for BeagleBoard.org PocketBeagle

Texas Instruments AM3358 based low-cost board using Octavo Systems OSD3358 SIP
with built-in TPS65217 PMIC and 512MB DDR3. Board features small 35mm x
55mm size, high-speed USB OTG, microSD and 72 0.1" expansion header
pins with 2xSPI, 2xI2C, 2xUART, USB, 8xADC, up-to-44 GPIO, PRU pins and much more.

https://beagleboard.org/pocket

This was tested using the am335x_evm_usbspl_defconfig.

Note that MII pins are enabled despite not having Ethernet on this
board. This avoids an issue where otherwise many timeout errors would be
generated. See https://e2e.ti.com/support/arm/sitara_arm/f/791/t/298976
for some related discussion.

Signed-off-by: Jason Kridner <jdk@ti.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

board: ti: am335x: Fix scale_vcore for beaglebones

commit 0650798824 ("board: am335x: Introduce scale_vcores")
updated voltages of each board based on efuse. It updated
beagle bone specific voltages

board: ti: am335x: Fix scale_vcore for beaglebones

commit 0650798824 ("board: am335x: Introduce scale_vcores")
updated voltages of each board based on efuse. It updated
beagle bone specific voltages under the condition board_is_bone().
But this is true only for BeagleBoneWhite. Due to which voltages
are not configured for BBB, BBW as wrong device is being probed.

So create a common function board_is_beaglebonex() which includes
am335x based beagle family. Use this for updating voltages.

Also remove extra if condition for selecting voltages which is
done later using a switch case and match usb current limit as
before the commit 0650798824.

Fixes: 0650798824 ("board: am335x: Introduce scale_vcores")
Reported-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot

arm: am33xx: Initialize EMIF REG_PR_OLD_COUNT for BBB and am335x-evm

Initialize EMIF OCP_CONFIG registers REG_COS_COUNT_1, REG_COS_COUNT_2,
and REG_PR_OLD_COUNT field for Beaglebone-Black and am335x

arm: am33xx: Initialize EMIF REG_PR_OLD_COUNT for BBB and am335x-evm

Initialize EMIF OCP_CONFIG registers REG_COS_COUNT_1, REG_COS_COUNT_2,
and REG_PR_OLD_COUNT field for Beaglebone-Black and am335x-evm. With
the default values LCDC suffers from DMA FIFO underflows and frame
synchronization lost errors. The initialization values are the highest
that work flawlessly when heavy memory load is generated by CPU. 32bpp
colors were used in the test. On BBB the video mode used 110MHz pixel
clock. The mode supported by the panel of am335x-evm uses 30MHz pixel
clock.

Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot

Signed-off-by: Stefano Babic <sbabic@denx.de>

board: AM335x-ICEv2: Add epprom support

Similar to other TI's AM335x platforms, AM335x ICEv2 also has an
eeprom populated for its unique identification. Adding this info
so that AM335x ICEv2 specifi

board: AM335x-ICEv2: Add epprom support

Similar to other TI's AM335x platforms, AM335x ICEv2 also has an
eeprom populated for its unique identification. Adding this info
so that AM335x ICEv2 specific initialization can be done.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

show more ...

ti: AM335x: Use generic EEPROM detection logic

Use the generic EEPROM detection logic instead of duplicating the AM
eeprom logic.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Steven Kip

ti: AM335x: Use generic EEPROM detection logic

Use the generic EEPROM detection logic instead of duplicating the AM
eeprom logic.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Steven Kipisz <s-kipisz2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

Merge branch 'master' of git://88.191.163.10/u-boot-arm

Fixup an easy conflict over adding the clk_get prototype and USB_OTG
defines for am33xx having moved.

Conflicts:
arch/arm/include/asm/arch-a

Merge branch 'master' of git://88.191.163.10/u-boot-arm

Fixup an easy conflict over adding the clk_get prototype and USB_OTG
defines for am33xx having moved.

Conflicts:
arch/arm/include/asm/arch-am33xx/hardware.h

Signed-off-by: Tom Rini <trini@ti.com>

show more ...

Merge git://git.denx.de/u-boot-arm

Conflicts:
board/freescale/mx6qsabrelite/Makefile
board/freescale/mx6qsabrelite/mx6qsabrelite.c
include/configs/mx6qsabrelite.h

Signed-off-by: Stefano Babic <s

Merge git://git.denx.de/u-boot-arm

Conflicts:
board/freescale/mx6qsabrelite/Makefile
board/freescale/mx6qsabrelite/mx6qsabrelite.c
include/configs/mx6qsabrelite.h

Signed-off-by: Stefano Babic <sbabic@denx.de>

show more ...

am335x_evm: Rework board_is_foo() checks

We rework the various board_is_foo() checks to take a pointer to
struct am335x_baseboard_id rather than using a local copy in board.c.
This allows us to make

am335x_evm: Rework board_is_foo() checks

We rework the various board_is_foo() checks to take a pointer to
struct am335x_baseboard_id rather than using a local copy in board.c.
This allows us to make use of the same checks in mux.c as well as fixing
problems when this code could be running from read-only memory.

Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Tom Rini <trini@ti.com>

show more ...

Merge branch 'u-boot/master' into u-boot-arm/master

Add GPL-2.0+ SPDX-License-Identifier to source files

Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>

Merge git://git.denx.de/u-boot

Merge branch 'master' of git://git.denx.de/u-boot-arm

Merge remote-tracking branch 'u-boot-ti/master'

Merge branch 'master' of git://git.denx.de/u-boot-arm

Merge remote-tracking branch 'u-boot-ti/master'

am33xx: Enable UART{1,2,3,4,5} pin-mux

If configured to use UART{1,2,3,4,5} such as on the Beaglebone RS232
cape or on the am335x_evm daughterboard, enable the proper pin-muxing.

Signed-off-by: And

am33xx: Enable UART{1,2,3,4,5} pin-mux

If configured to use UART{1,2,3,4,5} such as on the Beaglebone RS232
cape or on the am335x_evm daughterboard, enable the proper pin-muxing.

Signed-off-by: Andrew Bradford <andrew@bradfordembedded.com>

show more ...

am33xx: move ti i2c baseboard header handling to board/ti/am335x/

The i2c header is specific to ti(-derived) boards, and not generic for all
am335x boards.

Signed-off-by: Peter Korsgaard <peter.kor

am33xx: move ti i2c baseboard header handling to board/ti/am335x/

The i2c header is specific to ti(-derived) boards, and not generic for all
am335x boards.

Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
[trini: Make re-apply with rtc32k_enable() applied]
Signed-off-by: Tom Rini <trini@ti.com>

show more ...