Merge git://git.denx.de/u-boot-sunxi

sunxi: Fix A20-OLinuXino-MICRO LAN8710 support

>From revision J the board uses new phy chip LAN8710. Compared
with RTL8201, RA17 pin is TXERR. It has pullup which causes phy
not to work. To fix this

sunxi: Fix A20-OLinuXino-MICRO LAN8710 support

>From revision J the board uses new phy chip LAN8710. Compared
with RTL8201, RA17 pin is TXERR. It has pullup which causes phy
not to work. To fix this PA17 is muxed with GMAC function. This
makes the pin output-low.

Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>

show more ...

Merge branch 'master' of http://git.denx.de/u-boot-sunxi

sunxi: Fix gmac not working due to cpu_eth_init no longer being called

cpu_eth_init is no longer called for dm enabled eth drivers, this
was causing the sunxi gmac eth controller to no longer work i

sunxi: Fix gmac not working due to cpu_eth_init no longer being called

cpu_eth_init is no longer called for dm enabled eth drivers, this
was causing the sunxi gmac eth controller to no longer work in u-boot.

This commit fixes this by calling the clock, reset and pinmux setup
function from s_init() and enabling the phy power pin (if any) from
board_init().

The enabling of phy power cannot be done from s_init because it uses dm
and dm is not ready yet at this point.

Note that the mdelay is dropped as the phy gets enabled much earlier
now, so it is no longer needed.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Tested-by: Karsten Merker <merker@debian.org>
Tested-by: Michael Haas <haas@computerlinguist.org>

show more ...

Merge branch 'u-boot/master' into 'u-boot-arm/master'

Merge branch 'master' of git://git.denx.de/u-boot-sunxi

sunxi: Introduce a hidden SUNXI_GEN_SUNxI Kconfig bool

sun6i and newer (derived) SoCs such as the sun8i-a23, sun8i-a33 and sun9i
have a various things in common, like having separate ahb reset contr

sunxi: Introduce a hidden SUNXI_GEN_SUNxI Kconfig bool

sun6i and newer (derived) SoCs such as the sun8i-a23, sun8i-a33 and sun9i
have a various things in common, like having separate ahb reset control
registers, the SID living inside the pmic, custom pmic busses, new style
watchdog, etc.

This commit introduces a new hidden SUNXI_GEN_SUN6I Kconfig bool which can be
used to check for these features avoiding the need for an ever growing list
of "#if defined CONFIG_MACH_SUN?I" conditionals as we add support for more
"new style" sunxi SoCs.

Note that this commit changes the behavior of the gmac and hdmi code for
sun8i and the upcoming sun9i devices. This does not matter as sun8i does
not have gmac nor hdmi, and sun9i has new hardware-blocks for these so
the old code will not work there.

Also this is intentional as if a sun8i / sun9i variant which does use the
old hwblocks shows up then the GEN_SUN6I code paths will be the right ones
to use.

For completeness this also adds a SUNXI_GEN_SUN4I bool for A10/A13/A20.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

show more ...

dm: sunxi: Support driver model for Ethernet

Adjust the Ethernet initialisation code to support driver model.
It is no-longer necessary to call designware_initialize(). The device will
be probed whe

dm: sunxi: Support driver model for Ethernet

Adjust the Ethernet initialisation code to support driver model.
It is no-longer necessary to call designware_initialize(). The device will
be probed when it is used. The PHY type and GMAC base will come from the
device tree.

Signed-off-by: Simon Glass <sjg@chromium.org>

show more ...

Merge branch 'master' of http://git.denx.de/u-boot-sunxi

sunxi: GPIO pin mux hardware-feature-specific function index defines

Each hardware feature exposed through the GPIO pin mux is usually using the same
function index (for a given port), so there is n

sunxi: GPIO pin mux hardware-feature-specific function index defines

Each hardware feature exposed through the GPIO pin mux is usually using the same
function index (for a given port), so there is no need to define one value per
pin: one value per hardware feature per port is sufficient, avoids duplication
and makes everything easier to understand.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

show more ...

Merge remote-tracking branch 'u-boot/master' into 'u-boot-arm/master'

Merge branch 'master' of git://git.denx.de/u-boot

Merge branch 'master' of git://git.denx.de/u-boot-sunxi

sunxi: Add a GMAC Transmit Clock Delay Chain Kconfig option

And use this to set the GMAC Transmit Clock Delay Chain value on Banana
boards, rather then keying of CONFIG_TARGET_FOO.

Signed-off-by: H

sunxi: Add a GMAC Transmit Clock Delay Chain Kconfig option

And use this to set the GMAC Transmit Clock Delay Chain value on Banana
boards, rather then keying of CONFIG_TARGET_FOO.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

show more ...

sun7i: Add new Bananapro board / defconfig

Add support for the new Bananapro A20 development board from lemaker.org.
This board features 1G RAM, 2 USB A receptacles, 1 micro USB receptacle for
OTG,

sun7i: Add new Bananapro board / defconfig

Add support for the new Bananapro A20 development board from lemaker.org.
This board features 1G RAM, 2 USB A receptacles, 1 micro USB receptacle for
OTG, 1 micro USB receptacle for power, HDMI, sata, Gbit ethernet, ir receiver,
3.5 mm jack for a/v out, on board microphone, 40 gpio pins and sdio wifi.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

show more ...

Merge branch 'master' of http://git.denx.de/u-boot-sunxi

sun6i: Add gmac support for sun6i boards

Hookup the gmac found on the sun6i / A31 SoCs.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

Merge branch 'master' of git://git.denx.de/u-boot-sunxi

sunxi: gmac: Update bananapi fixup to the new CONFIG_TARGET_<BOARD> structure

The magic bit toucher needs to be updated to reflect the new board Kconfig structure

Signed-off-by: Zoltan HERPAI <wigy

sunxi: gmac: Update bananapi fixup to the new CONFIG_TARGET_<BOARD> structure

The magic bit toucher needs to be updated to reflect the new board Kconfig structure

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

show more ...

Merge branch 'u-boot/master' into 'u-boot-arm/master'

sunxi: Fix gmac not working reliable on the Bananapi

In order for the gmac nic to work reliable on the Bananapi, we need to set
bits 10-12 GTXDC "GMAC Transmit Clock Delay Chain" of the GMAC clk reg

sunxi: Fix gmac not working reliable on the Bananapi

In order for the gmac nic to work reliable on the Bananapi, we need to set
bits 10-12 GTXDC "GMAC Transmit Clock Delay Chain" of the GMAC clk register
(0x01c20164) to 3.

Without this about 9 out of 10 ethernet packets get lost, with this setting
there is no packet loss.

So far setting these bits is only necessary on the Bananapi, so this commit
solves this with a bit of #ifdef CONFIG_BANANAPI code. If in the future we
need to do something similar for other boards, we can create a specific
CONFIG_FOO option for this then.

Reported-by: Karsten Merker <merker@debian.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Karsten Merker <merker@debian.org>
Tested-by: Zoltan HERPAI <wigyori@openwrt.org>
Tested-by: Tony Zhang <tony.zhang@lemaker.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-arm

Merge branch 'master' of git://git.denx.de/u-boot-arm

Merge branch 'u-boot-sunxi/master' into 'u-boot-arm/master'

sunxi: Add support for using MII phy-s with the GMAC nic

Many A20 boards (ie Cubieboard2, A20-OLinuXino_MICRO) use an 100 Mbit MII
phy together with the GMAC nic found in the A20 SoC, add support fo

sunxi: Add support for using MII phy-s with the GMAC nic

Many A20 boards (ie Cubieboard2, A20-OLinuXino_MICRO) use an 100 Mbit MII
phy together with the GMAC nic found in the A20 SoC, add support for this
(this will get used when we add these boards in a later patch).

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

show more ...