|
Revision tags: v00.04.15, v00.04.14, v00.04.13, v00.04.12, v00.04.11, v00.04.10, v00.04.09, v00.04.08, v00.04.07, v00.04.06, v00.04.05, v00.04.04, v00.04.03, v00.04.02, v00.04.01, v00.04.00, v2021.04, v00.03.03, v2021.01, v2020.10, v2020.07, v00.02.13, v2020.04, v2020.01, v2019.10, v00.02.05, v00.02.04, v00.02.03, v00.02.02, v00.02.01, v2019.07, v00.02.00, v2019.04, v2018.07, v2018.03 |
|
| #
8e9801c2 |
| 15-Jan-2018 |
Tom Rini <trini@konsulko.com> |
Merge git://git.denx.de/u-boot-imx
|
|
Revision tags: v2018.01 |
|
| #
db00e921 |
| 03-Jan-2018 |
Fabio Estevam <fabio.estevam@nxp.com> |
mx6memcal: Fix the UART ports for mx6sabresd/auto boards
mx6sabresd board uses the following pins for console:
PAD_CSI0_DAT10__UART1_TX_DATA
PAD_CSI0_DAT11__UART1_RX_DATA
,so put it in the same co
mx6memcal: Fix the UART ports for mx6sabresd/auto boards
mx6sabresd board uses the following pins for console:
PAD_CSI0_DAT10__UART1_TX_DATA
PAD_CSI0_DAT11__UART1_RX_DATA
,so put it in the same config option as wandboard.
mx6sabreauto board uses the following pins for console:
PAD_KEY_COL0__UART4_TX_DATA
PAD_KEY_ROW0__UART4_RX_DATA
So do not mention sabreauto board as part of the UART1_SD3_DAT6_7 option.
The config option for sabreauto can be added later when needed.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
show more ...
|
| #
2f4c9de3 |
| 08-Jan-2018 |
Tom Rini <trini@konsulko.com> |
Merge git://git.denx.de/u-boot-imx
|
| #
baefb63a |
| 11-Dec-2017 |
Eric Nelson <eric@nelint.com> |
mx6: Add board mx6memcal for use in validating DDR
This is a virtual "board" that uses configuration files and
Kconfig to define the memory layout used by a real board during
the board bring-up proc
mx6: Add board mx6memcal for use in validating DDR
This is a virtual "board" that uses configuration files and
Kconfig to define the memory layout used by a real board during
the board bring-up process.
It generates an SPL image that can be loaded using imx_usb or
SB_LOADER.exe.
When run, it will generate a set of calibration constants for
use in either or both a DCD configuration file for boards that
use u-boot.imx or struct mx6_mmdc_calibration for boards that
boot via SPL.
In essence, it is a configurable, open-source variant of the
Freescale ddr-stress tool.
https://community.nxp.com/docs/DOC-105652
File mx6memcal_defconfig configures the board for use with
mx6sabresd or mx6qsabreauto.
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
show more ...
|