Merge tag 'u-boot-amlogic-20181126' of git://git.denx.de/u-boot-amlogic

Cleanup and update towards support for Amlogic Meson AXG SoCs :
- mmc: meson-gx: Add AXG compatible
- net: designware: add mes

Merge tag 'u-boot-amlogic-20181126' of git://git.denx.de/u-boot-amlogic

Cleanup and update towards support for Amlogic Meson AXG SoCs :
- mmc: meson-gx: Add AXG compatible
- net: designware: add meson meson compatibles
- Amlogic Meson cleanup for AXG SoC support

show more ...

ARM: meson: factorize common code out amlogic's boards

Now we have moved all the Amlogic board support to common generic board code,
we can move the identical board_init() and ft_board_setup() funct

ARM: meson: factorize common code out amlogic's boards

Now we have moved all the Amlogic board support to common generic board code,
we can move the identical board_init() and ft_board_setup() functions to
weak functions into the board-common mach-meson file.

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

show more ...

ARM: meson: rework soc arch file to prepare for new SoC

We are about to add support for the Amlogic AXG SoC. While very close to
the Gx SoC family, we will need to handle a few thing which are diffe

ARM: meson: rework soc arch file to prepare for new SoC

We are about to add support for the Amlogic AXG SoC. While very close to
the Gx SoC family, we will need to handle a few thing which are different
in this SoC. Rework the meson arch directory to prepare for this.

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

show more ...

boards: amlogic: remove ethernet gpio reset code from boards

The reset is already handled by the designware driver using
information from device tree.

Signed-off-by: Beniamino Galvani <b.galvani@gm

boards: amlogic: remove ethernet gpio reset code from boards

The reset is already handled by the designware driver using
information from device tree.

Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>

show more ...

meson: use the clock driver

Use the clk framework to initialize clocks from drivers that need them
instead of having hardcoded frequencies and initializations from board
code.

Signed-off-by: Beniam

meson: use the clock driver

Use the clk framework to initialize clocks from drivers that need them
instead of having hardcoded frequencies and initializations from board
code.

Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

show more ...

ARM: meson: rename GXBB to GX

Taking into account the Amlogic Family name starts with GX, including
the GXBB, GXL and GXM SoCs.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

net: Move enetaddr env access code to env config instead of net config

In order that we can use eth_env_* even when CONFIG_NET isn't set, move
these functions to environment code from net code.

Thi

net: Move enetaddr env access code to env config instead of net config

In order that we can use eth_env_* even when CONFIG_NET isn't set, move
these functions to environment code from net code.

This fixes failures such as:

board/ti/am335x/built-in.o: In function `board_late_init':
board/ti/am335x/board.c:752: undefined reference to `eth_env_set_enetaddr'
u-boot/board/ti/am335x/board.c:766: undefined reference to `eth_env_set_enetaddr'

which caters for use cases such as:

commit f411b5cca48f ("board: am335x: Always set eth/eth1addr environment
variable")

when Ethernet is required in Linux, but not U-Boot.

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>

show more ...

ARM: arch-meson: build memory banks using reported memory from registers

As discussed at [1], the Amlogic Meson GX SoCs can embed a BL31 firmware
and a secondary BL32 firmware.
Since mid-2017, the r

ARM: arch-meson: build memory banks using reported memory from registers

As discussed at [1], the Amlogic Meson GX SoCs can embed a BL31 firmware
and a secondary BL32 firmware.
Since mid-2017, the reserved memory address of the BL31 firmware was moved
and grown for security reasons.

But mainline U-Boot and Linux has the old address and size fixed.

These SoCs have a register interface to get the two firmware reserved
memory start and sizes.

This patch adds a dynamic reservation of the memory zones in the device tree bootmem
reserved memory zone used by the kernel in early boot.
To be complete, the memory zones are also added to the EFI reserved zones.

Depends on patchset "Add support for Amlogic GXL Based SBCs" at [2].

[1] http://lists.infradead.org/pipermail/linux-amlogic/2017-October/004860.html
[2] http://lists.infradead.org/pipermail/linux-amlogic/2017-November/005410.html

Changes since v1:
- switched the #if to if(IS_ENABLED()) to compile all code paths
- renamed function to meson_board_add_reserved_memory()
- added a mem.h header with comment
- updated all boards ft_board_setup()

Changes since RFC v2:
- reduced preprocessor load
- kept Odroid-C2 static memory mapping as exception

Changes since RFC v1:
- switch to fdt rsv mem table and efi reserve memory
- replaced in_le32 by readl()

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[trini: Fix warning on khadas-vim over missing <asm/arch/mem.h>
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

board: odroid-c2: use common ethernet init function

Switch Odroid-C2 Ethernet init to the common Ethernet init function.

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <n

board: odroid-c2: use common ethernet init function

Switch Odroid-C2 Ethernet init to the common Ethernet init function.

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

show more ...

Merge git://git.denx.de/u-boot-i2c

odroid-c2: enable I2C

Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>

env: Rename eth_getenv_enetaddr() to eth_env_get_enetaddr()

Rename this function for consistency with env_get().

Signed-off-by: Simon Glass <sjg@chromium.org>

env: Rename getenv/_f() to env_get()

We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.

Quite a few place

env: Rename getenv/_f() to env_get()

We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.

Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.

Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>

show more ...

env: Rename eth_setenv_enetaddr() to eth_env_set_enetaddr()

Rename this function for consistency with env_set().

Signed-off-by: Simon Glass <sjg@chromium.org>

env: Rename setenv() to env_set()

We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.

Suggested-by: Wolfgang Denk <wd

env: Rename setenv() to env_set()

We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.

Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>

show more ...

odroid-c2: Populate serial# environment variable from efuse

dm: Use dm.h header when driver mode is used

This header includes things that are needed to make driver build. Adjust
existing users to include that always, even if other dm/ includes are
present

S

dm: Use dm.h header when driver mode is used

This header includes things that are needed to make driver build. Adjust
existing users to include that always, even if other dm/ includes are
present

Signed-off-by: Simon Glass <sjg@chromium.org>

show more ...

meson: odroid-c2: enable Ethernet support through the device tree

Remove the device definition from board file, update the driver with
the new compatible property and update config with necessary op

meson: odroid-c2: enable Ethernet support through the device tree

Remove the device definition from board file, update the driver with
the new compatible property and update config with necessary options.

Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

show more ...

board: amlogic: Rename folder for Amlogic boards

s/hardkernel/amlogic/ to have a single place for all the amlogic-based
boards.

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Carlo Caio

board: amlogic: Rename folder for Amlogic boards

s/hardkernel/amlogic/ to have a single place for all the amlogic-based
boards.

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>

show more ...