Merge git://git.denx.de/u-boot-marvell

arm: mvebu: Move PCI(e) MBUS window to end of RAM

With patch 49b23e035d96 (pci: mvebu: Increase size of PCIe default mapping)
the mapping size for each PCI(e) controller was increased from 32MiB to

arm: mvebu: Move PCI(e) MBUS window to end of RAM

With patch 49b23e035d96 (pci: mvebu: Increase size of PCIe default mapping)
the mapping size for each PCI(e) controller was increased from 32MiB to
128MiB. This leads to problems on boards with multiple PCIe slots / ports
which are unable to map all PCIe ports, e.g. the Armada-XP theadorable:

DRAM: 2 GiB (667 MHz, 64-bit, ECC not enabled)
SF: Detected m25p128 with page size 256 Bytes, erase size 256 KiB, total 16 MiB
Cannot add window '4:f8', conflicts with another window
PCIe unable to add mbus window for mem at f0000000+08000000
Model: Marvell Armada XP theadorable

This patch moves the base address for the PCI(e) memory spaces from
0xe8000000 to the end of SDRAM (clipped to a max of 0xc0000000 right now).
This gives move room and flexibility for PCI(e) mappings.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: VlaoMao <vlaomao@gmail.com>
Tested-by: VlaoMao <vlaomao at gmail.com>

show more ...

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Merge git://www.denx.de/git/u-boot-marvell

ARM: mvebu: handle unused DRAM banks with ECC enabled

dram_ecc_scrubbing() had code to skip unused DRAM banks but it would not
work because mvebu_sdram_bs() returns 0 and the code was subtracting 1

ARM: mvebu: handle unused DRAM banks with ECC enabled

dram_ecc_scrubbing() had code to skip unused DRAM banks but it would not
work because mvebu_sdram_bs() returns 0 and the code was subtracting 1
before checking the size. Remove the -1 from the bank size and the +1
from the total which will skip unused banks and still calculate the
correct size. Put the -1 where it is needed for scrubbing via the xor
engine.

Reported-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>

show more ...

ARM: mvebu: add additional information to board_add_ram_info()

Display more information about the current RAM configuration. With these
changes the output on a 88F6820 board is

SoC: MV88F6820-A

ARM: mvebu: add additional information to board_add_ram_info()

Display more information about the current RAM configuration. With these
changes the output on a 88F6820 board is

SoC: MV88F6820-A0 at 1600 MHz
DRAM: 2 GiB (800 MHz, 32-bit, ECC not enabled)

Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>

show more ...

board_f: Drop setup_dram_config() wrapper

By making dram_init_banksize() return an error code we can drop the
wrapper. Adjust this and clean up all implementations.

Signed-off-by: Simon Glass <sjg@

board_f: Drop setup_dram_config() wrapper

By making dram_init_banksize() return an error code we can drop the
wrapper. Adjust this and clean up all implementations.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>

show more ...

Merge git://www.denx.de/git/u-boot-marvell

Conflicts:
arch/arm/Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>

arm: mvebu: Move SoC selection (A38X vs AXP) into Kconfig

Until now, the SoC selection for the ARCH_MVEBU platforms has been done
in the config header. Using CONFIG_ARMADA_XP in a non-clear way. As

arm: mvebu: Move SoC selection (A38X vs AXP) into Kconfig

Until now, the SoC selection for the ARCH_MVEBU platforms has been done
in the config header. Using CONFIG_ARMADA_XP in a non-clear way. As
it needed to get selected for AXP and A38x based boards. This patch
now changes this to move the SoC selection to Kconfig. And also
uses CONFIG_ARCH_MVEBU as a common define for both AXP and A38x.
This makes things a bit clearer - especially for new board additions.

Additionally the defines CONFIG_SYS_MVEBU_DDR_AXP and
CONFIG_SYS_MVEBU_DDR_A38X are replaced with the already available
CONFIG_ARMADA_38X and CONFIG_ARMADA_XP.

And CONFIG_DDR3 is removed, as its not referenced anywhere.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>

show more ...

arm: mvebu: Print CPU and SDRAM frequency upon startup

With this patch, the CPU and the DDR frequencies will get printed in the
U-Boot startup messages. Resulting in such a log:

U-Boot 2016.01-rc2-

arm: mvebu: Print CPU and SDRAM frequency upon startup

With this patch, the CPU and the DDR frequencies will get printed in the
U-Boot startup messages. Resulting in such a log:

U-Boot 2016.01-rc2-00188-gb8eeaec-dirty (Dec 21 2015 - 12:32:35 +0100)

SoC: MV78460-B0 at 1600 MHz
I2C: ready
DRAM: 4 GiB (800 MHz, ECC not enabled)
...

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>

show more ...

Merge git://git.denx.de/u-boot-marvell

arm: mvebu: Add complete SDRAM ECC scrubbing

This patch introduces the SDRAM scrubbing for ECC enabled board
to fill/initialize the ECC bytes. This is done via the XOR engine
to speed up the process

arm: mvebu: Add complete SDRAM ECC scrubbing

This patch introduces the SDRAM scrubbing for ECC enabled board
to fill/initialize the ECC bytes. This is done via the XOR engine
to speed up the process. The scrubbing is a 2-stage process:

1) SPL scrubs the area 0 - 0x100.0000 (16MiB) for the main U-Boot
2) U-Boot scrubs the remaining SDRAM area(s)

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>

show more ...

arm: mvebu: dram.c: Rework dram_init() and dram_init_banksize()

Rework these functions so that dram_init_banksize() does not call
dram_init() again. It only needs to set the banksize values in the
b

arm: mvebu: dram.c: Rework dram_init() and dram_init_banksize()

Rework these functions so that dram_init_banksize() does not call
dram_init() again. It only needs to set the banksize values in the
bdinfo struct.

Make sure to also clip the size of the last bank if it exceeds the
maximum allowed value of 3 GiB (0xc000.0000). Otherwise other
address windows (e.g. PCIe) will overlap with this memory window.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>

show more ...

arm: mvebu: Display ECC enabled / disabled upon bootup

This patch adds "(ECC enabled)" or "(ECC disabled)" to the DRAM
bootup text. Making it easier for board with SPD DIMM's to see,
if ECC is enabl

arm: mvebu: Display ECC enabled / disabled upon bootup

This patch adds "(ECC enabled)" or "(ECC disabled)" to the DRAM
bootup text. Making it easier for board with SPD DIMM's to see,
if ECC is enabled or not.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>

show more ...

arm: mvebu/armada100: dram.c: Remove CONFIG_SYS_BOARD_DRAM_INIT

CONFIG_SYS_BOARD_DRAM_INIT is not defined anywhere. So lets get rid
of all references here.

Signed-off-by: Stefan Roese <sr@denx.de>

arm: mvebu/armada100: dram.c: Remove CONFIG_SYS_BOARD_DRAM_INIT

CONFIG_SYS_BOARD_DRAM_INIT is not defined anywhere. So lets get rid
of all references here.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>

show more ...

Merge git://git.denx.de/u-boot-marvell

arm: mvebu: Move mvebu-common into mach-mvebu

Now that the mach-mvebu directory exists and is used by Armada XP we can
move the mvebu-common files into this directory as well.

Signed-off-by: Stefan

arm: mvebu: Move mvebu-common into mach-mvebu

Now that the mach-mvebu directory exists and is used by Armada XP we can
move the mvebu-common files into this directory as well.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>

show more ...