Merge git://git.denx.de/u-boot-dm

tegra: fdt: Ensure that the console UART is enabled

Many tegra boards have the console UART node disabled. With livetree this
prevents serial from working since it does not 'force' the console to be

tegra: fdt: Ensure that the console UART is enabled

Many tegra boards have the console UART node disabled. With livetree this
prevents serial from working since it does not 'force' the console to be
bound. Updates the affected boards to fix this error.

The boards were checked with:

for b in $(grep tegra boards.cfg |grep -v integrator | \
awk '{print $7}' | sort); do
echo $b;
fdtgrep -c nvidia,tegra20-uart b/$b/u-boot.dtb |grep okay;
done

Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-tegra

ARM: tegra: fix USB controller aliases

Some boards have a different set of USB controllers enabled in DT than
the set referenced by /alias entries. This patch fixes that. For
example, this avoids th

ARM: tegra: fix USB controller aliases

Some boards have a different set of USB controllers enabled in DT than
the set referenced by /alias entries. This patch fixes that. For
example, this avoids the following message while booting on Ventana,
which is caused by the fact that the USB0 controller had no alias, and
defaulted to wanting a sequence number of 0, which was later explicitly
requested by the alias for USB controller 2.

USB2: Device 'usb@c5008000': seq 0 is in use by 'usb@c5000000'

This didn't affect USB operation in any way though.

Related, there's no need for the USB controller aliases to have an order
that's different from the HW order, so re-order any aliases to match the
HW ordering. This has the benefit that since USB controller 0 is the only
one that supports device-mode in HW, and U-Boot only supports enabling
device move on controller 0, there's now good synergy in the ordering! For
Tegra20, that's not relevant at present since USB device mode doesn't work
correctly on that SoC, but it will save some head-scratching later.

This patch doesn't fix the colibri_t20 board, even though it has the same
issue, since Marcel already sent a patch for that.

Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Harmony and Ventana

show more ...

mmc: tegra: use correct alias for SDHCI/MMC nodes

The Tegra MMC driver currently honors "sdhci" entries in /aliases. The
MMC core however uses "mmc" entries in /aliases. This difference will be
rele

mmc: tegra: use correct alias for SDHCI/MMC nodes

The Tegra MMC driver currently honors "sdhci" entries in /aliases. The
MMC core however uses "mmc" entries in /aliases. This difference will be
relevant once the Tegra MMC driver is converted to DM, and the MMC core
handles alias lookups. To avoid issues during that conversion, fix the
Tegra MMC driver and all Tegra DTs to use the same alias name as the MMC
core does.

Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-tegra

tegra: dts: Sync tegra20.dtsi with Linux v4.4

This file has changed quite a bit since it was set up. Sync it back with
Linux v4.4. Adjust the users slightly to cope with the changes:

- the host1x n

tegra: dts: Sync tegra20.dtsi with Linux v4.4

This file has changed quite a bit since it was set up. Sync it back with
Linux v4.4. Adjust the users slightly to cope with the changes:

- the host1x node is now called host1x@50000000
- we need a clocks node to provide the clk32k_in phandle
- active usb nodes need status = "okay"
- active i2c nodes need status = "okay"

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>

show more ...

Merge remote-tracking branch 'u-boot/master' into 'u-boot-arm/master'

Merge branch 'master' of git://git.denx.de/u-boot

Merge branch 'master' of git://git.denx.de/u-boot-dm

dm: tegra: dts: Use TEGRA_GPIO() macro for all GPIOs

This new method is much easier and matches the kernel.

Signed-off-by: Simon Glass <sjg@chromium.org>

Merge branch 'master' of git://git.denx.de/u-boot-tegra

ARM: tegra: Enable PCIe on TrimSlice

The TrimSlice has an ethernet NIC connected to the PCIe bus. Enable the
PCIe controller and the network driver so that the device can boot over
the network.

Sig

ARM: tegra: Enable PCIe on TrimSlice

The TrimSlice has an ethernet NIC connected to the PCIe bus. Enable the
PCIe controller and the network driver so that the device can boot over
the network.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>

show more ...

Merge git://git.denx.de/u-boot-dm

dm: tegra: dts: Add aliases for spi on tegra30 boards

All boards with a SPI interface have a suitable spi alias except the tegra30
boards. Add these missing aliases.

Signed-off-by: Simon Glass <sjg

dm: tegra: dts: Add aliases for spi on tegra30 boards

All boards with a SPI interface have a suitable spi alias except the tegra30
boards. Add these missing aliases.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-arm

Merge branch 'master' of git://git.denx.de/u-boot-dm

tegra: dts: Add serial port details

Some Tegra device tree files do not include information about the serial
ports. Add this and also add information about the input clock speed.

The console alias

tegra: dts: Add serial port details

Some Tegra device tree files do not include information about the serial
ports. Add this and also add information about the input clock speed.

The console alias needs to be set up to indicate which port is used for
the console.

Also add a binding file since this is missing.

Series-changes; 5
- Add full serial port nodes from Linux tree (commit fc9d4dbe)
- Use /chosen/stdout-path instead of /aliases/console to specify the console

Signed-off-by: Simon Glass <sjg@chromium.org>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-arm

Merge branch 'u-boot/master' into 'u-boot-arm/master'

Conflicts:
Makefile
drivers/net/npe/Makefile

These two conflicts arise from commit 0b2d3f20
("ARM: NET: Remove the IXP NPE ethernet driver")

Merge branch 'u-boot/master' into 'u-boot-arm/master'

Conflicts:
Makefile
drivers/net/npe/Makefile

These two conflicts arise from commit 0b2d3f20
("ARM: NET: Remove the IXP NPE ethernet driver") and are
resolved by deleting the drivers/net/npe/Makefile file
and removing the CONFIG_IXP4XX_NPE line from Makefile.

show more ...

dts: move device tree sources to arch/$(ARCH)/dts/

Unlike Linux Kernel, U-Boot historically had *.dts files under
board/$(VENDOR)/dts/ and *.dtsi files under arch/$(ARCH)/dts/.

I think arch/$(ARCH)

dts: move device tree sources to arch/$(ARCH)/dts/

Unlike Linux Kernel, U-Boot historically had *.dts files under
board/$(VENDOR)/dts/ and *.dtsi files under arch/$(ARCH)/dts/.

I think arch/$(ARCH)/dts dicretory is a better location
to store both *.dts and *.dtsi files.

For example, before this commit, board/xilinx/dts directory
had both Microblaze dts (microblaze-generic.dts) and
ARM dts (zynq-*.dts), which are totally unrelated.

This commit moves *.dts to arch/$(ARCH)/dts/ directories,
allowing us to describe nicely mutiple DTBs generation in the next commit.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

show more ...