|
Revision tags: v00.04.15, v00.04.14, v00.04.13, v00.04.12, v00.04.11, v00.04.10, v00.04.09, v00.04.08, v00.04.07, v00.04.06, v00.04.05, v00.04.04, v00.04.03, v00.04.02, v00.04.01, v00.04.00, v2021.04, v00.03.03, v2021.01, v2020.10, v2020.07, v00.02.13, v2020.04, v2020.01, v2019.10, v00.02.05, v00.02.04, v00.02.03, v00.02.02, v00.02.01, v2019.07, v00.02.00, v2019.04 |
|
| #
0e62d5b2 |
| 05-Apr-2019 |
Tom Rini <trini@konsulko.com> |
Merge tag 'u-boot-imx-20190405' of git://git.denx.de/u-boot-imx
Fixes for 2019.04
- fix bashism for MX8
- fix ethernet for MX53
- fix docs for i.MX8
|
| #
da60b430 |
| 01-Apr-2019 |
Lukasz Majewski <lukma@denx.de> |
DTS: Fix ETH PHY reset on HSC|DDC boards (imx53)
After the commit: "eth: dm: fec: Add gpio phy reset binding"
SHA1: efd0b791069af93e9d439a70d1fe2ae8994dbbfa
The FEC ETH driver switched to PHY GPIO
DTS: Fix ETH PHY reset on HSC|DDC boards (imx53)
After the commit: "eth: dm: fec: Add gpio phy reset binding"
SHA1: efd0b791069af93e9d439a70d1fe2ae8994dbbfa
The FEC ETH driver switched to PHY GPIO reset performed with data defined
in DTS.
For the HSC|DDC boards the GPIO reset signal is active low and hence the
wrong DTS description must be changed (otherwise the reset for ETH is not
properly setup).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
show more ...
|
|
Revision tags: v2018.07 |
|
| #
de766105 |
| 27-Jun-2018 |
Tom Rini <trini@konsulko.com> |
Merge git://git.denx.de/u-boot-imx
|
| #
0b35b2d1 |
| 20-May-2018 |
Lukasz Majewski <lukma@denx.de> |
board: Add support for KEY1 status detection on K+P's HSC|DDC boards
This code provides information if the K+P's imx53 boards had KEY1
pressed.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
| #
642c1f51 |
| 20-May-2018 |
Lukasz Majewski <lukma@denx.de> |
board: imx53: Always disable display before starting kernel
This patch prevents from the situation where we may end up with garbage
displayed on the LCD panel.
Such situation occurs when one perfor
board: imx53: Always disable display before starting kernel
This patch prevents from the situation where we may end up with garbage
displayed on the LCD panel.
Such situation occurs when one performs "reboot -f" in Linux and then
stop in U-boot (or observe the garbage on the screen during boot up).
To prevent from such situation - the PWM pin is configured as GPIO and set
to LOW.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
show more ...
|
| #
5f787864 |
| 18-May-2018 |
Tom Rini <trini@konsulko.com> |
Merge git://git.denx.de/u-boot-imx
|
| #
ee943655 |
| 26-Apr-2018 |
Lukasz Majewski <lukma@denx.de> |
arm: imx53: Add support for imx53 boards from K+P
This commit adds support for DDC and HSC boards from
K+P in u-boot.
Console output:
U-Boot 2018.05-rc2-00090-g752b7ed6f9 (Apr 26 2018 - 14:24:24 +
arm: imx53: Add support for imx53 boards from K+P
This commit adds support for DDC and HSC boards from
K+P in u-boot.
Console output:
U-Boot 2018.05-rc2-00090-g752b7ed6f9 (Apr 26 2018 - 14:24:24 +0200)
CPU: Freescale i.MX53 rev2.1 at 800 MHz
Reset cause: WDOG
Model: K+P iMX53
DRAM: 512 MiB
MMC: FSL_SDHC: 0
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Module EEPROM:
ID: TQMa53-CB.0401
SN: 63152762
MAC: 00:0b:64:03:14:2a
BBoard:40x0 Rev:10
Net: eth0: ethernet@63fec000
Hit any key to stop autoboot: 0
Signed-off-by: Lukasz Majewski <lukma@denx.de>
show more ...
|