arm: dts: dra7: sync DT with latest Linux

Sync all dra7* specific dts files with the upstream
kernel including changes queued for 4.14

https://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-o

arm: dts: dra7: sync DT with latest Linux

Sync all dra7* specific dts files with the upstream
kernel including changes queued for 4.14

https://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap.git/log/?h=omap-for-v4.14/dt-v3

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

ARM: dts: dra7xx: sync DT with latest Linux

Sync all dra7xx based dts files with latest Linux

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

ARM: dts: dra72: add rev C evm support

Add DTS support for dra72 evm Rev C which has the following
changes
* Two ethernet ports now instead of the single one in rev B.
* DP83867 ethernet phy instead

ARM: dts: dra72: add rev C evm support

Add DTS support for dra72 evm Rev C which has the following
changes
* Two ethernet ports now instead of the single one in rev B.
* DP83867 ethernet phy instead of DP838865.

Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

ARM: dts: dra72-evm: fix broken ethernet

With commit ceec08f50b6, phy is connected to slave 0, but
changing the phy node was missed, fix it by populating the
phy node to proper cpsw slave node.

Fix

ARM: dts: dra72-evm: fix broken ethernet

With commit ceec08f50b6, phy is connected to slave 0, but
changing the phy node was missed, fix it by populating the
phy node to proper cpsw slave node.

Fixes: ceec08f50b6 ("ARM: dts: dra72-evm: Add mode-gpios entry for mac node")
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Vignesh R <vigneshr@ti.com>
Tested-by: Tom Rini <trini@konsulko.com>

show more ...

ARM: dts: dra7xx-evm: add evm_3v3_sd regulator

Add a node for evm_3v3_sd using onboard PCF GPIO expander which feeds
on to mmc vdd.
Update mapping for vmmc-supply and vmmc_aux-supply.
evm_3v3_sd sup

ARM: dts: dra7xx-evm: add evm_3v3_sd regulator

Add a node for evm_3v3_sd using onboard PCF GPIO expander which feeds
on to mmc vdd.
Update mapping for vmmc-supply and vmmc_aux-supply.
evm_3v3_sd supplies to SD card vdd, and ldo1 to sdcard i/o lines.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

ARM: dts: dra72-evm: Add mode-gpios entry for mac node

On DRA72 EVM, cpsw slave1 is muxed with VIN2A, hence switch to cpsw
slave0 for ethernet. This is controlled by pcf gpio line. Add
appropriate m

ARM: dts: dra72-evm: Add mode-gpios entry for mac node

On DRA72 EVM, cpsw slave1 is muxed with VIN2A, hence switch to cpsw
slave0 for ethernet. This is controlled by pcf gpio line. Add
appropriate mode-gpios DT entry so that driver can select the required
slave.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>

show more ...

ARM: dts: dra7xx: Add u-boot specific property for PCF8575 nodes

PCF8575 does not have any registers hence, offset field needs to be
ignored for i2c read/write. Therefore populate u-boot,i2c-offset-

ARM: dts: dra7xx: Add u-boot specific property for PCF8575 nodes

PCF8575 does not have any registers hence, offset field needs to be
ignored for i2c read/write. Therefore populate u-boot,i2c-offset-len
with 0 in PCF8575 DT nodes.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

ARM: dts: dra7xx: Update spi-max-frequency for QSPI

According to AM572x DM SPRS953A, QSPI max bus speed is 76.8MHz.
Therefore update the spi-max-frequency value of QSPI node for DRA74 and
DRA72 evm.

ARM: dts: dra7xx: Update spi-max-frequency for QSPI

According to AM572x DM SPRS953A, QSPI max bus speed is 76.8MHz.
Therefore update the spi-max-frequency value of QSPI node for DRA74 and
DRA72 evm. This increase flash read speed by ~2MB/s.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-spi

ARM: dts: dra7x: Support QSPI MODE-0 operation at 64MHz

According to Data Manual(SPRS915P) of AM57x, TI QSPI controller on
DRA74(rev 1.1+)/DRA72 EVM can support up to 64MHz in MODE-0, whereas
MODE-3

ARM: dts: dra7x: Support QSPI MODE-0 operation at 64MHz

According to Data Manual(SPRS915P) of AM57x, TI QSPI controller on
DRA74(rev 1.1+)/DRA72 EVM can support up to 64MHz in MODE-0, whereas
MODE-3 is limited to 48MHz. Hence, switch to MODE-0 for better
throughput.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>

show more ...

ARM: dts: dra7xx: am57xx: fix cd-gpios definition as per hardware design and dt binding docs

As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardwar

ARM: dts: dra7xx: am57xx: fix cd-gpios definition as per hardware design and dt binding docs

As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardware is designed with active
high card detect, gpio polarity has to be changed with
cd-inverted dt property.

In DRA72x and AM57xx EVMs the card detect gpio is designed as
active low gpio. So correcting the dt card detect gpio
definition.

Also adding card-detect gpio for DRA74x EVM.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

Merge git://git.denx.de/u-boot-dm

arm: dts: dra72-evm: add tick-timer to chosen node

Specify timer2 to be used as tick-timer in chosen node.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.c

arm: dts: dra72-evm: add tick-timer to chosen node

Specify timer2 to be used as tick-timer in chosen node.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

arm: dts: dra72-evm: add spi-flash comaptible for flash

In U-Boot most flashes uses "spi-flash" as compatible to bind the
device to flash driver, so adding "spi-flash" compatible to
m25p80 node.

Si

arm: dts: dra72-evm: add spi-flash comaptible for flash

In U-Boot most flashes uses "spi-flash" as compatible to bind the
device to flash driver, so adding "spi-flash" compatible to
m25p80 node.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>

show more ...

dra7xx: Add dra72_evm_defconfig using CONFIG_DM

- Import various DT files for DRA7 / DR72x / dra72-evm from Linux Kernel
v4.1
- Add config file for this board, enable DM and DM_GPIO

Cc: Simon Gla

dra7xx: Add dra72_evm_defconfig using CONFIG_DM

- Import various DT files for DRA7 / DR72x / dra72-evm from Linux Kernel
v4.1
- Add config file for this board, enable DM and DM_GPIO

Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

show more ...