tpm: Extend common APIs to support TPM TIS I2C

Qemu already supports devices attached to ISA and sysbus. This drop adds
support for the I2C bus attached TPM devices.

This commit includes changes fo

tpm: Extend common APIs to support TPM TIS I2C

Qemu already supports devices attached to ISA and sysbus. This drop adds
support for the I2C bus attached TPM devices.

This commit includes changes for the common code.
- Added support for the new checksum registers which are required for
the I2C support. The checksum calculation is handled in the qemu
common code.
- Added wrapper function for read and write data so that I2C code can
call it without MMIO interface.

The TPM TIS I2C spec describes in the table in section "Interface Locality
Usage per Register" that the TPM_INT_ENABLE and TPM_INT_STATUS registers
must be writable for any locality even if the locality is not the active
locality. Therefore, remove the checks whether the writing locality is the
active locality for these registers.

Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>

show more ...

Merge tag 'pull-tpm-2023-04-20-1' of https://github.com/stefanberger/qemu-tpm into staging

Merge tpm 2023/04/20 v1

# -----BEGIN PGP SIGNATURE-----
#
# iQEzBAABCAAdFiEEuBi5yt+QicLVzsZrda1lgCoLQhEFAm

Merge tag 'pull-tpm-2023-04-20-1' of https://github.com/stefanberger/qemu-tpm into staging

Merge tpm 2023/04/20 v1

# -----BEGIN PGP SIGNATURE-----
#
# iQEzBAABCAAdFiEEuBi5yt+QicLVzsZrda1lgCoLQhEFAmRBLgoACgkQda1lgCoL
# QhEPyQf/WfEg8k2hDLExobsSgup1IsnT+mHHTBOZVJvq2efg2YXUTHA56fmD9X6d
# crqTq68L5oaMES5iYEZhA7EAgfk3RvxDQGrlXBByPzrc6SSwEHHMR4Zzi5zrbCoW
# t6TmaKQrlQqYwkhhsbyqnG46bj0ugCDagkBLfJdVl96fjkYgTspcDxaNwqwy/DPn
# GTmQlvdRY09D1nylIdtcLBIfsM+sIkRslyngbUEIy+Bx8EWRy2a8Qw0BdY9g1XoE
# e0CaRaFMpju1KOIjq0YSIzt0LSQDFfPc1IlUAC0ZALhNmp+PPNtr4E7+4kFfO2ym
# 1sT2w25ho8dYDdm/m8tIauCdGoHw4A==
# =ML27
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 20 Apr 2023 01:20:26 PM BST
# gpg: using RSA key B818B9CADF9089C2D5CEC66B75AD65802A0B4211
# gpg: Good signature from "Stefan Berger <stefanb@linux.vnet.ibm.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B818 B9CA DF90 89C2 D5CE C66B 75AD 6580 2A0B 4211

* tag 'pull-tpm-2023-04-20-1' of https://github.com/stefanberger/qemu-tpm:
qtest: Add a test case for TPM TIS I2C connected to Aspeed I2C controller
qtest: Move tpm_util_tis_transmit() into tpm-tis-utils.c and rename it
qtest: Add functions for accessing devices on Aspeed I2C controller
tests/avocado/aspeed: Add TPM TIS I2C test
tpm: Add support for TPM device over I2C bus
tpm: Extend common APIs to support TPM TIS I2C
docs: Add support for TPM devices over I2C bus

Signed-off-by: Richard Henderson <richard.henderson@linaro.org>

show more ...

tpm: Extend common APIs to support TPM TIS I2C

Qemu already supports devices attached to ISA and sysbus. This drop adds
support for the I2C bus attached TPM devices.

This commit includes changes fo

tpm: Extend common APIs to support TPM TIS I2C

Qemu already supports devices attached to ISA and sysbus. This drop adds
support for the I2C bus attached TPM devices.

This commit includes changes for the common code.
- Added support for the new checksum registers which are required for
the I2C support. The checksum calculation is handled in the qemu
common code.
- Added wrapper function for read and write data so that I2C code can
call it without MMIO interface.

The TPM TIS I2C spec describes in the table in section "Interface Locality
Usage per Register" that the TPM_INT_ENABLE and TPM_INT_STATUS registers
must be writable for any locality even if the locality is not the active
locality. Therefore, remove the checks whether the writing locality is the
active locality for these registers.

Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Message-id: 20230414220754.1191476-3-ninadpalsule@us.ibm.com

show more ...

Merge remote-tracking branch 'remotes/stefanberger/tags/pull-tpm-2021-06-15-1' into staging

Merge tpm 2021/06/15 v1

# gpg: Signature made Tue 15 Jun 2021 16:09:31 BST
# gpg: using RS

Merge remote-tracking branch 'remotes/stefanberger/tags/pull-tpm-2021-06-15-1' into staging

Merge tpm 2021/06/15 v1

# gpg: Signature made Tue 15 Jun 2021 16:09:31 BST
# gpg: using RSA key B818B9CADF9089C2D5CEC66B75AD65802A0B4211
# gpg: Good signature from "Stefan Berger <stefanb@linux.vnet.ibm.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B818 B9CA DF90 89C2 D5CE C66B 75AD 6580 2A0B 4211

* remotes/stefanberger/tags/pull-tpm-2021-06-15-1:
tpm: Return QMP error when TPM is disabled in build
sysemu: Make TPM structures inaccessible if CONFIG_TPM is not defined
acpi: Eliminate all TPM related code if CONFIG_TPM is not set
arm: Eliminate all TPM related code if CONFIG_TPM is not set
i386: Eliminate all TPM related code if CONFIG_TPM is not set

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

show more ...

acpi: Eliminate all TPM related code if CONFIG_TPM is not set

Cc: M: Michael S. Tsirkin <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>

acpi: Eliminate all TPM related code if CONFIG_TPM is not set

Cc: M: Michael S. Tsirkin <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210614191335.1968807-4-stefanb@linux.ibm.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>

show more ...

Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging

pci, pc, virtio: fixes, features

tpm physical presence interface
rsc support in virtio net
ivshmem is removed
misc cleanups

Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging

pci, pc, virtio: fixes, features

tpm physical presence interface
rsc support in virtio net
ivshmem is removed
misc cleanups and fixes all over the place

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

# gpg: Signature made Fri 18 Jan 2019 02:11:11 GMT
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469

* remotes/mst/tags/for_upstream: (49 commits)
migration: Use strnlen() for fixed-size string
migration: Fix stringop-truncation warning
hw/acpi: Use QEMU_NONSTRING for non NUL-terminated arrays
block/sheepdog: Use QEMU_NONSTRING for non NUL-terminated arrays
qemu/compiler: Define QEMU_NONSTRING
acpi: update expected files
hw: acpi: Fix memory hotplug AML generation error
tpm: clear RAM when "memory overwrite" requested
acpi: add ACPI memory clear interface
acpi: build TPM Physical Presence interface
acpi: expose TPM/PPI configuration parameters to firmware via fw_cfg
tpm: allocate/map buffer for TPM Physical Presence interface
tpm: add a "ppi" boolean property
hw/misc/edu: add msi_uninit() for pci_edu_uninit()
virtio: Make disable-legacy/disable-modern compat properties optional
globals: Allow global properties to be optional
virtio: virtio 9p really requires CONFIG_VIRTFS to work
virtio: split virtio crypto bits from virtio-pci.h
virtio: split virtio gpu bits from virtio-pci.h
virtio: split virtio serial bits from virtio-pci
...

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

show more ...

acpi: build TPM Physical Presence interface

The TPM Physical Presence interface consists of an ACPI part, a shared
memory part, and code in the firmware. Users can send messages to the
firmware by w

acpi: build TPM Physical Presence interface

The TPM Physical Presence interface consists of an ACPI part, a shared
memory part, and code in the firmware. Users can send messages to the
firmware by writing a code into the shared memory through invoking the
ACPI code. When a reboot happens, the firmware looks for the code and
acts on it by sending sequences of commands to the TPM.

This patch adds the ACPI code. It is similar to the one in EDK2 but doesn't
assume that SMIs are necessary to use. It uses a similar datastructure for
the shared memory as EDK2 does so that EDK2 and SeaBIOS could both make use
of it. I extended the shared memory data structure with an array of 256
bytes, one for each code that could be implemented. The array contains
flags describing the individual codes. This decouples the ACPI implementation
from the firmware implementation.

The underlying TCG specification is accessible from the following page.

https://trustedcomputinggroup.org/tcg-physical-presence-interface-specification/

This patch implements version 1.30.

Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
[ Marc-André - ACPI code improvements and windows fixes ]
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

show more ...

acpi: expose TPM/PPI configuration parameters to firmware via fw_cfg

To avoid having to hard code the base address of the PPI virtual
memory device we introduce a fw_cfg file etc/tpm/config that hol

acpi: expose TPM/PPI configuration parameters to firmware via fw_cfg

To avoid having to hard code the base address of the PPI virtual
memory device we introduce a fw_cfg file etc/tpm/config that holds the
base address of the PPI device, the version of the PPI interface and
the version of the attached TPM.

Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
[ Marc-André: renamed to etc/tpm/config, made it static, document it ]
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

show more ...

tpm: allocate/map buffer for TPM Physical Presence interface

Implement a virtual memory device for the TPM Physical Presence interface.
The memory is located at 0xFED45000 and used by ACPI to send m

tpm: allocate/map buffer for TPM Physical Presence interface

Implement a virtual memory device for the TPM Physical Presence interface.
The memory is located at 0xFED45000 and used by ACPI to send messages to the
firmware (BIOS) and by the firmware to provide parameters for each one of
the supported codes.

This interface should be used by all TPM devices on x86 and can be
added by calling tpm_ppi_init_io().

Note: bios_linker cannot be used to allocate the PPI memory region,
since the reserved memory should stay stable across reboots, and might
be needed before the ACPI tables are installed.

Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

show more ...

Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging

* IEC units series (Philippe)
* Hyper-V PV TLB flush (Vitaly)
* git archive detection (Daniel)
* host serial passthrough

Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging

* IEC units series (Philippe)
* Hyper-V PV TLB flush (Vitaly)
* git archive detection (Daniel)
* host serial passthrough fix (David)
* NPT support for SVM emulation (Jan)
* x86 "info mem" and "info tlb" fix (Doug)

# gpg: Signature made Mon 02 Jul 2018 16:18:21 BST
# gpg: using RSA key BFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83

* remotes/bonzini/tags/for-upstream: (50 commits)
tcg: simplify !CONFIG_TCG handling of tb_invalidate_*
i386/monitor.c: make addresses canonical for "info mem" and "info tlb"
target-i386: Add NPT support
serial: Open non-block
bsd-user: Use the IEC binary prefix definitions
linux-user: Use the IEC binary prefix definitions
tests/crypto: Use the IEC binary prefix definitions
vl: Use the IEC binary prefix definitions
monitor: Use the IEC binary prefix definitions
cutils: Do not include "qemu/units.h" directly
hw/rdma: Use the IEC binary prefix definitions
hw/virtio: Use the IEC binary prefix definitions
hw/vfio: Use the IEC binary prefix definitions
hw/sd: Use the IEC binary prefix definitions
hw/usb: Use the IEC binary prefix definitions
hw/net: Use the IEC binary prefix definitions
hw/i386: Use the IEC binary prefix definitions
hw/ppc: Use the IEC binary prefix definitions
hw/mips: Use the IEC binary prefix definitions
hw/mips/r4k: Constify params_size
...

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

show more ...

hw/tpm: Use the IEC binary prefix definitions

It eases code review, unit is explicit.

Patch generated using:

$ git grep -E '(1024|2048|4096|8192|(<<|>>).?(10|20|30))' hw/ include/hw/

and modifi

hw/tpm: Use the IEC binary prefix definitions

It eases code review, unit is explicit.

Patch generated using:

$ git grep -E '(1024|2048|4096|8192|(<<|>>).?(10|20|30))' hw/ include/hw/

and modified manually.

Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20180625124238.25339-13-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

show more ...

Merge remote-tracking branch 'remotes/stefanberger/tags/pull-tpm-2018-02-21-2' into staging

Merge tpm 2018/02/21 v2

# gpg: Signature made Tue 27 Feb 2018 13:50:28 GMT
# gpg: using RS

Merge remote-tracking branch 'remotes/stefanberger/tags/pull-tpm-2018-02-21-2' into staging

Merge tpm 2018/02/21 v2

# gpg: Signature made Tue 27 Feb 2018 13:50:28 GMT
# gpg: using RSA key 75AD65802A0B4211
# gpg: Good signature from "Stefan Berger <stefanb@linux.vnet.ibm.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B818 B9CA DF90 89C2 D5CE C66B 75AD 6580 2A0B 4211

* remotes/stefanberger/tags/pull-tpm-2018-02-21-2:
tests: add test for TPM TIS device
tests: Move common TPM test code into tpm-emu.c

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

show more ...

tests: add test for TPM TIS device

Move the TPM TIS related register and flag #defines into
include/hw/acpi/tpm.h for access by the test case.

Write a test case that covers the TIS functionality.

tests: add test for TPM TIS device

Move the TPM TIS related register and flag #defines into
include/hw/acpi/tpm.h for access by the test case.

Write a test case that covers the TIS functionality.

Add the tests cases to the MAINTAINERS file.

Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>

show more ...

Merge remote-tracking branch 'remotes/stefanberger/tags/pull-tpm-2018-01-26-2' into staging

Merge tpm 2018/01/26 v2

# gpg: Signature made Mon 29 Jan 2018 22:20:05 GMT
# gpg: using RS

Merge remote-tracking branch 'remotes/stefanberger/tags/pull-tpm-2018-01-26-2' into staging

Merge tpm 2018/01/26 v2

# gpg: Signature made Mon 29 Jan 2018 22:20:05 GMT
# gpg: using RSA key 0x75AD65802A0B4211
# gpg: Good signature from "Stefan Berger <stefanb@linux.vnet.ibm.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B818 B9CA DF90 89C2 D5CE C66B 75AD 6580 2A0B 4211

* remotes/stefanberger/tags/pull-tpm-2018-01-26-2:
tpm: add CRB device
tpm: report backend request error
tpm: replace GThreadPool with AIO threadpool
tpm: lookup cancel path under tpm device class
tpm: fix alignment issues
tpm: Set the flags of the CMD_INIT command to 0

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

show more ...

tpm: add CRB device

tpm_crb is a device for TPM 2.0 Command Response Buffer (CRB)
Interface as defined in TCG PC Client Platform TPM Profile (PTP)
Specification Family “2.0” Level 00 Revision 01.03

tpm: add CRB device

tpm_crb is a device for TPM 2.0 Command Response Buffer (CRB)
Interface as defined in TCG PC Client Platform TPM Profile (PTP)
Specification Family “2.0” Level 00 Revision 01.03 v22.

The PTP allows device implementation to switch between TIS and CRB
model at run time, but given that CRB is a simpler device to
implement, I chose to implement it as a different device.

The device doesn't implement other locality than 0 for now (my laptop
TPM doesn't either, so I assume this isn't so bad)

Tested with some success with Linux upstream and Windows 10, seabios &
modified ovmf. The device is recognized and correctly transmit
command/response with passthrough & emu. However, we are missing PPI
ACPI part atm.

Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>

show more ...

Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging

pc, pci, tpm, virtio, vhost enhancements and fixes

A bunch of cleanups and fixes all over the place,
enhancements in TPM, v

Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging

pc, pci, tpm, virtio, vhost enhancements and fixes

A bunch of cleanups and fixes all over the place,
enhancements in TPM, virtio and vhost.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

# gpg: Signature made Mon Jun 1 13:19:48 2015 BST using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"

* remotes/mst/tags/for_upstream: (60 commits)
vhost-user: add multi queue support
virtio: make features 64bit wide
qdev: add 64bit properties
virtio-mmio: ioeventfd support
hw/acpi/aml-build: Fix memory leak
acpi: add aml_while() term
acpi: add aml_increment() term
acpi: add aml_shiftright() term
acpi: add aml_shiftleft() term
acpi: add aml_index() term
acpi: add aml_lless() term
acpi: add aml_add() term
TPM2 ACPI table support
tpm: Probe for connected TPM 1.2 or TPM 2
Extend TPM TIS interface to support TPM 2
Add stream ID to MSI write
acpi: Simplify printing to dynamic string
i386: drop FDC in pc-q35-2.4+ if neither it nor floppy drives are wanted
i386/pc_q35: don't insist on board FDC if there's no default floppy
i386/pc: '-drive if=floppy' should imply a board-default FDC
...

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

show more ...

TPM2 ACPI table support

Add a TPM2 ACPI table if a TPM 2 is used in the backend.
Also add an SSDT for the TPM 2.

Rename tpm_find() to tpm_get_version() and have this function
return the version of

TPM2 ACPI table support

Add a TPM2 ACPI table if a TPM 2 is used in the backend.
Also add an SSDT for the TPM 2.

Rename tpm_find() to tpm_get_version() and have this function
return the version of the TPM found, TPMVersion_Unspec if
no TPM is found. Use the version number to build version
specific ACPI tables.

Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

show more ...

Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging

pci, pc fixes, features

A bunch of bugfixes - these will make sense for 2.1.1

ACPI support for TPM and partial ARI support

Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging

pci, pc fixes, features

A bunch of bugfixes - these will make sense for 2.1.1

ACPI support for TPM and partial ARI support for PCIE.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

# gpg: Signature made Sun 24 Aug 2014 23:16:35 BST using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"

* remotes/mst/tags/for_upstream:
pcie: fix trailing whitespace
ioh3420: Enable ARI forwarding
ioh3420: Remove obsoleted, unused ioh3420_init function
pcie: Rename the pcie_cap_ari_* functions to pcie_cap_arifwd_*
pcie: Fix incorrect write to the ari capability next function field
ssdt-tpm: add generated hex file to git
Add ACPI tables for TPM
pc: reserve more memory for ACPI for new machine types
pcihp: fix possible array out of bounds
pci_bridge: manually destroy memory regions within PCIBridgeWindows
hostmem: set MPOL_MF_MOVE

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

show more ...

Add ACPI tables for TPM

Add an SSDT ACPI table for the TPM device.
Add a TCPA table for BIOS logging area when a TPM is being used.

The latter follows this spec here:

http://www.trustedcomputinggr

Add ACPI tables for TPM

Add an SSDT ACPI table for the TPM device.
Add a TCPA table for BIOS logging area when a TPM is being used.

The latter follows this spec here:

http://www.trustedcomputinggroup.org/files/static_page_files/DCD4188E-1A4B-B294-D050A155FB6F7385/TCG_ACPIGeneralSpecification_PublicReview.pdf

This patch has Michael Tsirkin's patches folded in.

Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>

show more ...