selftests: bonding: set active slave to primary eth1 specifically

[ Upstream commit cd65c48d66920457129584553f217005d09b1edb ]

In bond priority testing, we set the primary interface to eth1 and add

selftests: bonding: set active slave to primary eth1 specifically

[ Upstream commit cd65c48d66920457129584553f217005d09b1edb ]

In bond priority testing, we set the primary interface to eth1 and add
eth0,1,2 to bond in serial. This is OK in normal times. But when in
debug kernel, the bridge port that eth0,1,2 connected would start
slowly (enter blocking, forwarding state), which caused the primary
interface down for a while after enslaving and active slave changed.
Here is a test log from Jakub's debug test[1].

[ 400.399070][ T50] br0: port 1(s0) entered disabled state
[ 400.400168][ T50] br0: port 4(s2) entered disabled state
[ 400.941504][ T2791] bond0: (slave eth0): making interface the new active one
[ 400.942603][ T2791] bond0: (slave eth0): Enslaving as an active interface with an up link
[ 400.943633][ T2766] br0: port 1(s0) entered blocking state
[ 400.944119][ T2766] br0: port 1(s0) entered forwarding state
[ 401.128792][ T2792] bond0: (slave eth1): making interface the new active one
[ 401.130771][ T2792] bond0: (slave eth1): Enslaving as an active interface with an up link
[ 401.131643][ T69] br0: port 2(s1) entered blocking state
[ 401.132067][ T69] br0: port 2(s1) entered forwarding state
[ 401.346201][ T2793] bond0: (slave eth2): Enslaving as a backup interface with an up link
[ 401.348414][ T50] br0: port 4(s2) entered blocking state
[ 401.348857][ T50] br0: port 4(s2) entered forwarding state
[ 401.519669][ T250] bond0: (slave eth0): link status definitely down, disabling slave
[ 401.526522][ T250] bond0: (slave eth1): link status definitely down, disabling slave
[ 401.526986][ T250] bond0: (slave eth2): making interface the new active one
[ 401.629470][ T250] bond0: (slave eth0): link status definitely up
[ 401.630089][ T250] bond0: (slave eth1): link status definitely up
[...]
# TEST: prio (active-backup ns_ip6_target primary_reselect 1) [FAIL]
# Current active slave is eth2 but not eth1

Fix it by setting active slave to primary slave specifically before
testing.

[1] https://netdev-3.bots.linux.dev/vmksft-bonding-dbg/results/464301/1-bond-options-sh/stdout

Fixes: 481b56e0391e ("selftests: bonding: re-format bond option tests")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

selftests: bonding: Check initial state

[ Upstream commit 8cc063ae1b3dbe416ce62a15d49af4c2314b45fe ]

The purpose of the test_LAG_cleanup() function is to check that some
hardware addresses are remo

selftests: bonding: Check initial state

[ Upstream commit 8cc063ae1b3dbe416ce62a15d49af4c2314b45fe ]

The purpose of the test_LAG_cleanup() function is to check that some
hardware addresses are removed from underlying devices after they have been
unenslaved. The test function simply checks that those addresses are not
present at the end. However, if the addresses were never added to begin
with due to some error in device setup, the test function currently passes.
This is a false positive since in that situation the test did not actually
exercise the intended functionality.

Add a check that the expected addresses are indeed present after device
setup. This makes the test function more robust.

I noticed this problem when running the team/dev_addr_lists.sh test on a
system without support for dummy and ipv6:

tools/testing/selftests/drivers/net/team# ./dev_addr_lists.sh
Error: Unknown device type.
Error: Unknown device type.
This program is not intended to be run as root.
RTNETLINK answers: Operation not supported
TEST: team cleanup mode lacp [ OK ]

Fixes: bbb774d921e2 ("net: Add tests for bonding and team address list management")
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Link: https://lore.kernel.org/r/20240131140848.360618-3-bpoirier@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

selftests: bonding: do not test arp/ns target with mode balance-alb/tlb

[ Upstream commit a2933a8759a62269754e54733d993b19de870e84 ]

The prio_arp/ns tests hard code the mode to active-backup. At th

selftests: bonding: do not test arp/ns target with mode balance-alb/tlb

[ Upstream commit a2933a8759a62269754e54733d993b19de870e84 ]

The prio_arp/ns tests hard code the mode to active-backup. At the same
time, The balance-alb/tlb modes do not support arp/ns target. So remove
the prio_arp/ns tests from the loop and only test active-backup mode.

Fixes: 481b56e0391e ("selftests: bonding: re-format bond option tests")
Reported-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Closes: https://lore.kernel.org/netdev/17415.1705965957@famine/
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20240123075917.1576360-1-liuhangbin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

selftests: bonding: Increase timeout to 1200s

[ Upstream commit b01f15a7571b7aa222458bc9bf26ab59bd84e384 ]

When tests are run by runner.sh, bond_options.sh gets killed before
it can complete:

make

selftests: bonding: Increase timeout to 1200s

[ Upstream commit b01f15a7571b7aa222458bc9bf26ab59bd84e384 ]

When tests are run by runner.sh, bond_options.sh gets killed before
it can complete:

make -C tools/testing/selftests run_tests TARGETS="drivers/net/bonding"
[...]
# timeout set to 120
# selftests: drivers/net/bonding: bond_options.sh
# TEST: prio (active-backup miimon primary_reselect 0) [ OK ]
# TEST: prio (active-backup miimon primary_reselect 1) [ OK ]
# TEST: prio (active-backup miimon primary_reselect 2) [ OK ]
# TEST: prio (active-backup arp_ip_target primary_reselect 0) [ OK ]
# TEST: prio (active-backup arp_ip_target primary_reselect 1) [ OK ]
# TEST: prio (active-backup arp_ip_target primary_reselect 2) [ OK ]
#
not ok 7 selftests: drivers/net/bonding: bond_options.sh # TIMEOUT 120 seconds

This test includes many sleep statements, at least some of which are
related to timers in the operation of the bonding driver itself. Increase
the test timeout to allow the test to complete.

I ran the test in slightly different VMs (including one without HW
virtualization support) and got runtimes of 13m39.760s, 13m31.238s, and
13m2.956s. Use a ~1.5x "safety factor" and set the timeout to 1200s.

Fixes: 42a8d4aaea84 ("selftests: bonding: add bonding prio option test")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Closes: https://lore.kernel.org/netdev/20240116104402.1203850a@kernel.org/#t
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://lore.kernel.org/r/20240118001233.304759-1-bpoirier@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

selftests: bonding: Change script interpreter

[ Upstream commit c2518da8e6b0e248cfff1d4b6682e14020bd4d3f ]

The tests changed by this patch, as well as the scripts they source, use
features which ar

selftests: bonding: Change script interpreter

[ Upstream commit c2518da8e6b0e248cfff1d4b6682e14020bd4d3f ]

The tests changed by this patch, as well as the scripts they source, use
features which are not part of POSIX sh (ex. 'source' and 'local'). As a
result, these tests fail when /bin/sh is dash such as on Debian. Change the
interpreter to bash so that these tests can run successfully.

Fixes: d43eff0b85ae ("selftests: bonding: up/down delay w/ slave link flapping")
Tested-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

selftests: bonding: do not set port down when adding to bond

[ Upstream commit 61fa2493ca76fd7bb74e13f0205274f4ab0aa696 ]

Similar to commit be809424659c ("selftests: bonding: do not set port down
b

selftests: bonding: do not set port down when adding to bond

[ Upstream commit 61fa2493ca76fd7bb74e13f0205274f4ab0aa696 ]

Similar to commit be809424659c ("selftests: bonding: do not set port down
before adding to bond"). The bond-arp-interval-causes-panic test failed
after commit a4abfa627c38 ("net: rtnetlink: Enslave device before bringing
it up") as the kernel will set the port down _after_ adding to bond if setting
port down specifically.

Fix it by removing the link down operation when adding to bond.

Fixes: 2ffd57327ff1 ("selftests: bonding: cause oops in bond_rr_gen_slave_id")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Tested-by: Benjamin Poirier <benjamin.poirier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...