Merge tag 'v6.6.6' into dev-6.6

This is the 6.6.6 stable release

Signed-off-by: Joel Stanley <joel@jms.id.au>

usb: misc: onboard-hub: add support for Microchip USB5744

commit 6972b38ca05235f6142715db7062ecc87a422e22 upstream.

Add support for the Microchip USB5744 USB3.0 and USB2.0 Hub.

The Microchip USB57

usb: misc: onboard-hub: add support for Microchip USB5744

commit 6972b38ca05235f6142715db7062ecc87a422e22 upstream.

Add support for the Microchip USB5744 USB3.0 and USB2.0 Hub.

The Microchip USB5744 supports two power supplies, one for 1V2 and one
for 3V3. According to the datasheet there is no need for a delay between
power on and reset, so this value is set to 0.

Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Cc: stable <stable@kernel.org>
Acked-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20231113145921.30104-3-francesco@dolcini.it
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

Merge tag 'usb-6.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB / Thunderbolt fixes from Greg KH:
"Here are some USB and Thunderbolt driver fixes for 6.6-rc6 to resolve

Merge tag 'usb-6.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB / Thunderbolt fixes from Greg KH:
"Here are some USB and Thunderbolt driver fixes for 6.6-rc6 to resolve
a number of small reported issues. Included in here are:

- thunderbolt driver fixes

- xhci driver fixes

- cdns3 driver fixes

- musb driver fixes

- a number of typec driver fixes

- a few other small driver fixes

All of these have been in linux-next with no reported issues"

* tag 'usb-6.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (22 commits)
usb: typec: ucsi: Use GET_CAPABILITY attributes data to set power supply scope
usb: typec: ucsi: Fix missing link removal
usb: typec: altmodes/displayport: Signal hpd low when exiting mode
xhci: Preserve RsvdP bits in ERSTBA register correctly
xhci: Clear EHB bit only at end of interrupt handler
xhci: track port suspend state correctly in unsuccessful resume cases
usb: xhci: xhci-ring: Use sysdev for mapping bounce buffer
usb: typec: ucsi: Clear EVENT_PENDING bit if ucsi_send_command fails
usb: misc: onboard_hub: add support for Microchip USB2412 USB 2.0 hub
usb: gadget: udc-xilinx: replace memcpy with memcpy_toio
usb: cdns3: Modify the return value of cdns_set_active () to void when CONFIG_PM_SLEEP is disabled
usb: dwc3: Soft reset phy on probe for host
usb: hub: Guard against accesses to uninitialized BOS descriptors
usb: typec: qcom: Update the logic of regulator enable and disable
usb: gadget: ncm: Handle decoding of multiple NTB's in unwrap call
usb: musb: Get the musb_qh poniter after musb_giveback
usb: musb: Modify the "HWVers" register address
usb: cdnsp: Fixes issue with dequeuing not queued requests
thunderbolt: Restart XDomain discovery handshake after failure
thunderbolt: Correct TMU mode initialization from hardware
...

show more ...

usb: misc: onboard_hub: add support for Microchip USB2412 USB 2.0 hub

The USB2412 is a 2-Port USB 2.0 hub controller that provides a reset pin
and a single 3v3 powre source, which makes it suitable

usb: misc: onboard_hub: add support for Microchip USB2412 USB 2.0 hub

The USB2412 is a 2-Port USB 2.0 hub controller that provides a reset pin
and a single 3v3 powre source, which makes it suitable to be controlled
by the onboard_hub driver.

This hub has the same reset timings as USB2514/2517 and the same
onboard hub specific-data can be reused for USB2412.

Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Cc: stable <stable@kernel.org>
Acked-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20230911-topic-2412_onboard_hub-v1-1-7704181ddfff@wolfvision.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

Merge drm/drm-fixes into drm-misc-fixes

Forwarding to v6.6-rc1.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>

Merge tag 'usb-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB / Thunderbolt / PHY driver updates from Greg KH:
"Here is the big set of USB, Thunderbolt, and PHY drive

Merge tag 'usb-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB / Thunderbolt / PHY driver updates from Greg KH:
"Here is the big set of USB, Thunderbolt, and PHY driver updates for
6.6-rc1. Included in here are:

- PHY driver additions and cleanups

- Thunderbolt minor additions and fixes

- USB MIDI 2 gadget support added

- dwc3 driver updates and additions

- Removal of some old USB wireless code that was missed when that
codebase was originally removed a few years ago, cleaning up some
core USB code paths

- USB core potential use-after-free fixes that syzbot from different
people/groups keeps tripping over

- typec updates and additions

- gadget fixes and cleanups

- loads of smaller USB core and driver cleanups all over the place

Full details are in the shortlog. All of these have been in linux-next
for a while with no reported problems"

* tag 'usb-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (154 commits)
platform/chrome: cros_ec_typec: Configure Retimer cable type
tcpm: Avoid soft reset when partner does not support get_status
usb: typec: tcpm: reset counter when enter into unattached state after try role
usb: typec: tcpm: set initial svdm version based on pd revision
USB: serial: option: add FOXCONN T99W368/T99W373 product
USB: serial: option: add Quectel EM05G variant (0x030e)
usb: dwc2: add pci_device_id driver_data parse support
usb: gadget: remove max support speed info in bind operation
usb: gadget: composite: cleanup function config_ep_by_speed_and_alt()
usb: gadget: config: remove max speed check in usb_assign_descriptors()
usb: gadget: unconditionally allocate hs/ss descriptor in bind operation
usb: gadget: f_uvc: change endpoint allocation in uvc_function_bind()
usb: gadget: add a inline function gether_bitrate()
usb: gadget: use working speed to calcaulate network bitrate and qlen
dt-bindings: usb: samsung,exynos-dwc3: Add Exynos850 support
usb: dwc3: exynos: Add support for Exynos850 variant
usb: gadget: udc-xilinx: fix incorrect type in assignment warning
usb: gadget: udc-xilinx: fix cast from restricted __le16 warning
usb: gadget: udc-xilinx: fix restricted __le16 degrades to integer warning
USB: dwc2: hande irq on dead controller correctly
...

show more ...

Merge branch 'next' into for-linus

Prepare input updates for 6.6 merge window.

Merge drm/drm-next into drm-intel-next

Catching-up with drm-next and drm-intel-gt-next.
It will unblock a code refactor around the platform
definitions (names vs acronyms).

Signed-off-by: Rodrigo V

Merge drm/drm-next into drm-intel-next

Catching-up with drm-next and drm-intel-gt-next.
It will unblock a code refactor around the platform
definitions (names vs acronyms).

Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

show more ...

Merge drm/drm-next into drm-intel-gt-next

Need to pull in b3e4aae612ec ("drm/i915/hdcp: Modify hdcp_gsc_message msg sending mechanism") as
a dependency for https://patchwork.freedesktop.org/series/1

Merge drm/drm-next into drm-intel-gt-next

Need to pull in b3e4aae612ec ("drm/i915/hdcp: Modify hdcp_gsc_message msg sending mechanism") as
a dependency for https://patchwork.freedesktop.org/series/121735/

Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

show more ...

usb: misc: onboard-hub: add support for Cypress HX3 USB 3.0 family

The HX3 comes in different variants (up to 4 USB 3.0 ports; multi-TT),
e.g. CYUSB330x/CYUSB331x/CYUSB332x/CYUSB230x. It operates wi

usb: misc: onboard-hub: add support for Cypress HX3 USB 3.0 family

The HX3 comes in different variants (up to 4 USB 3.0 ports; multi-TT),
e.g. CYUSB330x/CYUSB331x/CYUSB332x/CYUSB230x. It operates with two
different power supplies: 1V2 and 3V3.

Add the support for this hub, for controlling the reset pin and the
power supplies.

Reset time is extracted from data sheet, page 24:
"The RESETN pin can be tied to VDD_IO through an external resistor and
to ground (GND) through an external capacitor (minimum 5 ms time
constant)."
V_IH min is given at 0.7 * 3V3 (page 34), therefore use 10ms.

Also add USB PIDs for the USB 2.0 and USB 3.0 root hub.

Acked-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Benjamin Bara <benjamin.bara@skidata.com>
Link: https://lore.kernel.org/r/20230620-hx3-v7-2-f79b4b22a1bf@skidata.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

usb: misc: onboard-hub: support multiple power supplies

As some of the onboard hubs require multiple power supplies, provide the
environment to support them.

Signed-off-by: Benjamin Bara <benjamin.

usb: misc: onboard-hub: support multiple power supplies

As some of the onboard hubs require multiple power supplies, provide the
environment to support them.

Signed-off-by: Benjamin Bara <benjamin.bara@skidata.com>
Acked-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20230620-hx3-v7-1-f79b4b22a1bf@skidata.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

usb: misc: onboard_usb_hub: add Genesys Logic GL3523 hub support

Genesys Logic GL3523 is a 4-port USB 3.1 hub that has a reset pin to
toggle and a 5.0V core supply exported though an integrated LDO

usb: misc: onboard_usb_hub: add Genesys Logic GL3523 hub support

Genesys Logic GL3523 is a 4-port USB 3.1 hub that has a reset pin to
toggle and a 5.0V core supply exported though an integrated LDO is
available for powering it.

Add the support for this hub, for controlling the reset pin and the core
power supply.

Signed-off-by: Anand Moon <linux.amoon@gmail.com>
[m.felsch@pengutronix.de: include review feedback & port to 6.4]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20230623142228.4069084-2-m.felsch@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

Merge drm/drm-next into drm-misc-next

Backmerging to get v6.5-rc2.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>

Merge tag 'v6.4' into next

Sync up with mainline to bring in updates to shared infrastructure.

ASoC: Merge v6.5-rc2

Get a similar baseline to my other branches, and fixes for people using
the branch.

Merge v6.5-rc1 into drm-misc-fixes

Boris needs 6.5-rc1 in drm-misc-fixes to prevent a conflict.

Signed-off-by: Maxime Ripard <mripard@kernel.org>

Merge tag 'usb-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB / Thunderbolt driver updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver updates fo

Merge tag 'usb-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB / Thunderbolt driver updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver updates for 6.5-rc1.

Included in here are:

- Lots of USB4/Thunderbolt additions and updates for new hardware
types and fixes as people are starting to get access to the
hardware in the wild

- new gadget controller driver, cdns2, added

- new typec drivers added

- xhci driver updates

- typec driver updates

- usbip driver fixes

- usb-serial driver updates and fixes

- lots of smaller USB driver updates

All of these have been in linux-next for a while with no reported
problems"

* tag 'usb-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (265 commits)
usb: host: xhci-plat: Set XHCI_STATE_REMOVING before resuming XHCI HC
usb: host: xhci: Do not re-initialize the XHCI HC if being removed
usb: typec: nb7vpq904m: fix CONFIG_DRM dependency
usbip: usbip_host: Replace strlcpy with strscpy
usb: dwc3: gadget: Propagate core init errors to UDC during pullup
USB: serial: option: add LARA-R6 01B PIDs
usb: ulpi: Make container_of() no-op in to_ulpi_dev()
usb: gadget: legacy: fix error return code in gfs_bind
usb: typec: fsa4480: add support for Audio Accessory Mode
usb: typec: fsa4480: rework mux & switch setup to handle more states
usb: typec: ucsi: call typec_set_mode on non-altmode partner change
USB: gadget: f_hid: make hidg_class a static const structure
USB: gadget: f_printer: make usb_gadget_class a static const structure
USB: mon: make mon_bin_class a static const structure
USB: gadget: udc: core: make udc_class a static const structure
USB: roles: make role_class a static const structure
dt-bindings: usb: dwc3: Add interrupt-names property support for wakeup interrupt
dt-bindings: usb: Add StarFive JH7110 USB controller
dt-bindings: usb: dwc3: Add IPQ9574 compatible
usb: cdns2: Fix spelling mistake in a trace message "Wakupe" -> "Wakeup"
...

show more ...

Merge branch 'drm-next' of git://anongit.freedesktop.org/drm/drm into msm-next-lumag-base

Merge the drm-next tree to pick up the DRM DSC helpers (merged via
drm-intel-next tree). MSM DSC v1.2 patche

Merge branch 'drm-next' of git://anongit.freedesktop.org/drm/drm into msm-next-lumag-base

Merge the drm-next tree to pick up the DRM DSC helpers (merged via
drm-intel-next tree). MSM DSC v1.2 patches depend on these helpers.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

show more ...

Merge tag 'v6.4-rc4' into wpan-next/staging

Linux 6.4-rc4

usb: misc: onboard_hub: Don't warn twice about problems during remove

If onboard_hub_power_off() called by onboard_hub_remove() fails it emits
an error message. Forwarding the returned error value t

usb: misc: onboard_hub: Don't warn twice about problems during remove

If onboard_hub_power_off() called by onboard_hub_remove() fails it emits
an error message. Forwarding the returned error value to the driver core
results in another error message. As the return value is otherwise
ignored, just drop the return value. There is no side effect apart from
suppressing the core's warning.

Instead of returning zero unconditionally, convert to .remove_new()
which has the same semantics as .remove() that unconditionally returns
zero.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230530073633.2193618-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

Merge drm/drm-next into drm-intel-next

Backmerge to get some hwmon dependencies.

Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

Merge branch 'next' into for-linus

Prepare input updates for 6.4 merge window.

Merge branch 'for-6.4/amd-sfh' into for-linus

- assorted functional fixes for amd-sfh driver (Basavaraj Natikar)

Merge tag 'kvmarm-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD

KVM/arm64 updates for 6.4

- Numerous fixes for the pathological lock inversion issue that
plagued K

Merge tag 'kvmarm-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD

KVM/arm64 updates for 6.4

- Numerous fixes for the pathological lock inversion issue that
plagued KVM/arm64 since... forever.

- New framework allowing SMCCC-compliant hypercalls to be forwarded
to userspace, hopefully paving the way for some more features
being moved to VMMs rather than be implemented in the kernel.

- Large rework of the timer code to allow a VM-wide offset to be
applied to both virtual and physical counters as well as a
per-timer, per-vcpu offset that complements the global one.
This last part allows the NV timer code to be implemented on
top.

- A small set of fixes to make sure that we don't change anything
affecting the EL1&0 translation regime just after having having
taken an exception to EL2 until we have executed a DSB. This
ensures that speculative walks started in EL1&0 have completed.

- The usual selftest fixes and improvements.

show more ...

Merge branch 'i2c/for-current' into i2c/for-mergewindow

This should have been in 6.3, but sadly I missed it.