Merge drm/drm-fixes into drm-misc-fixes

Forwarding to v6.6-rc1.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>

Merge tag 'rtc-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux

Pull RTC updates from Alexandre Belloni:
"Subsystem:

- Add a way for drivers to tell the core the supported a

Merge tag 'rtc-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux

Pull RTC updates from Alexandre Belloni:
"Subsystem:

- Add a way for drivers to tell the core the supported alarm range is
smaller than the date range. This is not used yet but will be
useful for the alarmtimers in the next release.

- fix Wvoid-pointer-to-enum-cast warnings

- remove redundant of_match_ptr()

- stop warning for invalid alarms when the alarm is disabled

Drivers:

- isl12022: allow setting the trip level for battery level detection

- pcf2127: add support for PCF2131 and multiple timestamps

- stm32: time precision improvement, many fixes

- twl: NVRAM support"

* tag 'rtc-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (73 commits)
dt-bindings: rtc: ds3231: Remove text binding
rtc: wm8350: remove unnecessary messages
rtc: twl: remove unnecessary messages
rtc: sun6i: remove unnecessary message
rtc: stop warning for invalid alarms when the alarm is disabled
rtc: twl: add NVRAM support
rtc: pcf85363: Allow to wake up system without IRQ
rtc: m48t86: add DT support for m48t86
dt-bindings: rtc: Add ST M48T86
rtc: pcf2127: remove useless check
rtc: rzn1: Report maximum alarm limit to rtc core
rtc: ds1305: Report maximum alarm limit to rtc core
rtc: tps6586x: Report maximum alarm limit to rtc core
rtc: cmos: Report supported alarm limit to rtc infrastructure
rtc: cros-ec: Detect and report supported alarm window size
rtc: Add support for limited alarm timer offsets
rtc: isl1208: Fix incorrect logic in isl1208_set_xtoscb()
MAINTAINERS: remove obsolete pattern in RTC SUBSYSTEM section
rtc: tps65910: Remove redundant dev_warn() and do not check for 0 return after calling platform_get_irq()
rtc: omap: Do not check for 0 return after calling platform_get_irq()
...

show more ...

rtc: isl12022: implement support for the #clock-cells DT property

If device tree implies that the chip's IRQ/F_OUT pin is used as a
clock, expose that in the driver. For now, pretend it is a
fixed-r

rtc: isl12022: implement support for the #clock-cells DT property

If device tree implies that the chip's IRQ/F_OUT pin is used as a
clock, expose that in the driver. For now, pretend it is a
fixed-rate (32kHz) clock; if other use cases appear the driver can be
updated to provide its own clk_ops etc.

When the clock output is not used on a given board, one can prolong
the battery life by ensuring that the FOx bits are 0. For the hardware
I'm currently working on, the RTC draws 1.2uA with the FOx bits at
their default 0001 value, dropping to 0.88uA when those bits are
cleared.

Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20230615105826.411953-9-linux@rasmusvillemoes.dk
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

show more ...

rtc: isl12022: trigger battery level detection during probe

Since the meaning of the SR_LBAT85 and SR_LBAT75 bits are different in
battery backup mode, they may very well be set after power on, and

rtc: isl12022: trigger battery level detection during probe

Since the meaning of the SR_LBAT85 and SR_LBAT75 bits are different in
battery backup mode, they may very well be set after power on, and
stay set for up to a minute (i.e. until the battery detection in VDD
mode happens when the seconds counter hits 59). This would mean that
userspace doing a ioctl(RTC_VL_READ) early on could get a false
positive.

The battery level detection can also be triggered by explicitly
writing a 1 to the TSE bit in the BETA register. Do that once during
boot. Empirically, this does not immediately update the bits in
the status register (i.e., an immediate read of SR after this write
can still show stale values), but the update is done after a few
milliseconds, so certainly before the RTC device gets registered and
userspace has a chance of doing the ioctl() on this device.

Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20230615105826.411953-7-linux@rasmusvillemoes.dk
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

show more ...

rtc: isl12022: implement RTC_VL_READ ioctl

Hook up support for reading the values of the SR_LBAT85 and SR_LBAT75
bits. Translate the former to "battery low", and the latter to
"battery empty or not-

rtc: isl12022: implement RTC_VL_READ ioctl

Hook up support for reading the values of the SR_LBAT85 and SR_LBAT75
bits. Translate the former to "battery low", and the latter to
"battery empty or not-present".

Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20230615105826.411953-6-linux@rasmusvillemoes.dk
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

show more ...

rtc: isl12022: add support for trip level DT binding

Implement support for using the values given in the
isil,battery-trip-levels-microvolt property to set appropriate values
in the VB85TP/VB75TP bi

rtc: isl12022: add support for trip level DT binding

Implement support for using the values given in the
isil,battery-trip-levels-microvolt property to set appropriate values
in the VB85TP/VB75TP bits in the PWR_VBAT register.

Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20230615105826.411953-5-linux@rasmusvillemoes.dk
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

show more ...

rtc: isl12022: remove wrong warning for low battery level

There are multiple problems with this warning.

First of all, it triggers way too often, in fact nearly on every boot,
because the SR_LBAT85

rtc: isl12022: remove wrong warning for low battery level

There are multiple problems with this warning.

First of all, it triggers way too often, in fact nearly on every boot,
because the SR_LBAT85/SR_LBAT75 bits have another meaning when in
battery backup mode. Quoting from the data sheet:

LOW BATTERY INDICATOR 85% BIT (LBAT85)

In Normal Mode (VDD), this bit indicates when the battery level has
dropped below the pre-selected trip levels. [...] The LBAT85
detection happens automatically once every minute when seconds
register reaches 59.

In Battery Mode (VBAT), this bit indicates the device has entered
into battery mode by polling once every 10 minutes. The LBAT85
detection happens automatically once when the minute register
reaches x9h or x0h minutes.

Similar wording applies to the LBAT75 bit.

This means that if the device is powered off for more than 10 minutes,
the LBAT85 bit is guaranteed to be set. Upon power-on, unless we're
close enough to the end of a minute and/or the boot is slow enough
that the second register passes 59, the LBAT85 bit is still set when
the kernel (or early userspace) reads the RTC to set the system's
wallclock time.

Another minor problem is with the bit logic. If the 75% level is
reached, logically we're also below 85%, so both bits would most
likely be set. So even if the battery is below 75%, the warning would
still say "voltage dropped below 85%".

A third problem is that the driver and current DT binding offer no way
to indicate the nominal battery level and/or settings of the Battery
Level Monitor Trip Bits. Since the default value of the VB85TP[2:0] and
VB75TP[2:0] bits are 000, this means the actual setting of the
LBAT85/LBAT75 bits in VDD mode doesn't happen until the battery is below
2.125V/1.875V, which for a standard 3V battery is way too late.

A fourth problem is emitting this warning from ->read_time:
util-linux' hwclock will, in the absence of support for getting an
interrupt when the seconds counter is updated, issue
ioctl(RTC_RD_TIME) in a busy-loop until it sees a change in the
seconds field. In that case, if the battery low bits are set (either
genuinely, more than a minute after boot, due to the battery actually
being low, or as above, bogusly shortly after boot), the kernel log is
swamped with hundreds of identical warnings.

Subsequent patches will add such bindings and driver support, and also
proper support for RTC_VL_READ. For now, remove the broken warning.

Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20230615105826.411953-2-linux@rasmusvillemoes.dk
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

show more ...

Merge drm/drm-next into drm-intel-next

Catching-up with drm-next and drm-intel-gt-next.
It will unblock a code refactor around the platform
definitions (names vs acronyms).

Signed-off-by: Rodrigo V

Merge drm/drm-next into drm-intel-next

Catching-up with drm-next and drm-intel-gt-next.
It will unblock a code refactor around the platform
definitions (names vs acronyms).

Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

show more ...

Merge drm/drm-next into drm-intel-gt-next

Need to pull in b3e4aae612ec ("drm/i915/hdcp: Modify hdcp_gsc_message msg sending mechanism") as
a dependency for https://patchwork.freedesktop.org/series/1

Merge drm/drm-next into drm-intel-gt-next

Need to pull in b3e4aae612ec ("drm/i915/hdcp: Modify hdcp_gsc_message msg sending mechanism") as
a dependency for https://patchwork.freedesktop.org/series/121735/

Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

show more ...

Merge drm/drm-next into drm-misc-next

Backmerging to get v6.5-rc2.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>

ASoC: Merge v6.5-rc2

Get a similar baseline to my other branches, and fixes for people using
the branch.

Merge v6.5-rc1 into drm-misc-fixes

Boris needs 6.5-rc1 in drm-misc-fixes to prevent a conflict.

Signed-off-by: Maxime Ripard <mripard@kernel.org>

Merge tag 'rtc-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux

Pull RTC updates from Alexandre Belloni:
"The isl1208 dirver was reworked tobe able to work as part of an MFD.

Merge tag 'rtc-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux

Pull RTC updates from Alexandre Belloni:
"The isl1208 dirver was reworked tobe able to work as part of an MFD.

All the Loongson chips are now supported through a new driver, the old
one is removed.

Summary:

Subsystem:
- Switch i2c drivers back to use .probe()
- Constify pointers to hwmon_channel_info

New driver:
- Loongson on chip RTC, replacing the Loongson 1 only driver

Drivers:
- isl1208: cleanup and support for RAA215300
- st-lpc: cleanups
- stm32: fix wakeup"

* tag 'rtc-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (21 commits)
rtc: Add rtc driver for the Loongson family chips
rtc: Remove the Loongson-1 RTC driver
dt-bindings: rtc: Split loongson,ls2x-rtc into SoC-based compatibles
rtc: rv3028: make rv3028 probeable from userspace
rtc: isl1208: Add support for the built-in RTC on the PMIC RAA215300
rtc: isl1208: Add isl1208_set_xtoscb()
rtc: isl1208: Drop enum isl1208_id and split isl1208_configs[]
rtc: isl1208: Make similar I2C and DT-based matching table
rtc: isl1208: Drop name variable
dt-bindings: rtc: isil,isl1208: Document clock and clock-names properties
dt-bindings: rtc: isl1208: Convert to json-schema
rtc: st-lpc: Simplify clk handling in st_rtc_probe()
rtc: st-lpc: Release some resources in st_rtc_probe() in case of error
rtc: stm32: remove dedicated wakeup management
dt-bindings: rtc: restrict node name suffixes
rtc: add HAS_IOPORT dependencies
rtc: Switch i2c drivers back to use .probe()
rtc: rv3032: constify pointers to hwmon_channel_info
rtc: isl12022: constify pointers to hwmon_channel_info
rtc: ds3232: constify pointers to hwmon_channel_info
...

show more ...

rtc: Switch i2c drivers back to use .probe()

After commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498b5 ("i

rtc: Switch i2c drivers back to use .probe()

After commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498b5 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230505121136.1185653-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

show more ...

rtc: isl12022: constify pointers to hwmon_channel_info

Statically allocated array of pointers to hwmon_channel_info can be made
const for safety.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlo

rtc: isl12022: constify pointers to hwmon_channel_info

Statically allocated array of pointers to hwmon_channel_info can be made
const for safety.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230511175609.282191-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

show more ...

Merge branch 'next' into for-linus

Prepare input updates for 6.4 merge window.

Merge branch 'for-6.4/amd-sfh' into for-linus

- assorted functional fixes for amd-sfh driver (Basavaraj Natikar)

Merge drm/drm-next into drm-intel-gt-next

Need to pull in commit from drm-next (earlier in drm-intel-next):

1eca0778f4b3 ("drm/i915: add struct i915_dsm to wrap dsm members together")

In order to

Merge drm/drm-next into drm-intel-gt-next

Need to pull in commit from drm-next (earlier in drm-intel-next):

1eca0778f4b3 ("drm/i915: add struct i915_dsm to wrap dsm members together")

In order to merge following patch to drm-intel-gt-next:

https://patchwork.freedesktop.org/patch/530942/?series=114925&rev=6

Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

show more ...

Merge drm/drm-next into drm-intel-next

Catch up with 6.3-rc cycle...

Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

Merge remote-tracking branch 'drm/drm-next' into msm-next

Merge drm-next into msm-next to pick up external clk and PM dependencies
for improved a6xx GPU reset sequence.

Signed-off-by: Rob Clark <ro

Merge remote-tracking branch 'drm/drm-next' into msm-next

Merge drm-next into msm-next to pick up external clk and PM dependencies
for improved a6xx GPU reset sequence.

Signed-off-by: Rob Clark <robdclark@chromium.org>

show more ...

Merge tag 'v6.3-rc2' into next

Merge with mainline to get of_property_present() and other newer APIs.

Merge drm/drm-fixes into drm-misc-fixes

Backmerging to get latest upstream.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>

Merge drm/drm-next into drm-misc-next

Backmerging to get v6.3-rc1 and sync with the other DRM trees.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>

Merge remote-tracking branch 'acme/perf-tools' into perf-tools-next

To pick up perf-tools fixes just merged upstream.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

Documentation/bpf/bpf_devel_QA.rst
b7abcd9c656b ("bpf, doc: Link to submitting-patches.rst for general patch submission info")
d56b

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

Documentation/bpf/bpf_devel_QA.rst
b7abcd9c656b ("bpf, doc: Link to submitting-patches.rst for general patch submission info")
d56b0c461d19 ("bpf, docs: Fix link to netdev-FAQ target")
https://lore.kernel.org/all/20230307095812.236eb1be@canb.auug.org.au/

Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...