Merge tag 'v6.6.53' into for/openbmc/dev-6.6

This is the 6.6.53 stable release

wifi: iwlwifi: clear trans->state earlier upon error

[ Upstream commit 094513f8a2fbddee51b055d8035f995551f98fce ]

When the firmware crashes, we first told the op_mode and only then,
changed the tra

wifi: iwlwifi: clear trans->state earlier upon error

[ Upstream commit 094513f8a2fbddee51b055d8035f995551f98fce ]

When the firmware crashes, we first told the op_mode and only then,
changed the transport's state. This is a problem if the op_mode's
nic_error() handler needs to send a host command: it'll see that the
transport's state still reflects that the firmware is alive.

Today, this has no consequences since we set the STATUS_FW_ERROR bit and
that will prevent sending host commands. iwl_fw_dbg_stop_restart_recording
looks at this bit to know not to send a host command for example.

To fix the hibernation, we needed to reset the firmware without having
an error and checking STATUS_FW_ERROR to see whether the firmware is
alive will no longer hold, so this change is necessary as well.

Change the flow a bit.
Change trans->state before calling the op_mode's nic_error() method and
check trans->state instead of STATUS_FW_ERROR. This will keep the
current behavior of iwl_fw_dbg_stop_restart_recording upon firmware
error, and it'll allow us to call iwl_fw_dbg_stop_restart_recording
safely even if STATUS_FW_ERROR is clear, but yet, the firmware is not
alive.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240825191257.9d7427fbdfd7.Ia056ca57029a382c921d6f7b6a6b28fc480f2f22@changeid
[I missed this was a dependency for the hibernation fix, changed
the commit message a bit accordingly]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

Merge tag 'v6.6.26' into dev-6.6

This is the 6.6.26 stable release

wifi: iwlwifi: disable multi rx queue for 9000

[ Upstream commit 29fa9a984b6d1075020f12071a89897fd62ed27f ]

Multi rx queue allows to spread the load of the Rx streams on different
CPUs. 9000 series

wifi: iwlwifi: disable multi rx queue for 9000

[ Upstream commit 29fa9a984b6d1075020f12071a89897fd62ed27f ]

Multi rx queue allows to spread the load of the Rx streams on different
CPUs. 9000 series required complex synchronization mechanisms from the
driver side since the hardware / firmware is not able to provide
information about duplicate packets and timeouts inside the reordering
buffer.

Users have complained that for newer devices, all those synchronization
mechanisms have caused spurious packet drops. Those packet drops
disappeared if we simplify the code, but unfortunately, we can't have
RSS enabled on 9000 series without this complex code.

Remove support for RSS on 9000 so that we can make the code much simpler
for newer devices and fix the bugs for them.

The down side of this patch is a that all the Rx path will be routed to
a single CPU, but this has never been an issue, the modern CPUs are just
fast enough to cope with all the traffic.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231017115047.2917eb8b7af9.Iddd7dcf335387ba46fcbbb6067ef4ff9cd3755a7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stable-dep-of: e78d78773089 ("wifi: iwlwifi: mvm: include link ID when releasing frames")
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

Merge tag 'v6.6.6' into dev-6.6

This is the 6.6.6 stable release

Signed-off-by: Joel Stanley <joel@jms.id.au>

wifi: iwlwifi: empty overflow queue during flush

[ Upstream commit 658939fc68d3241f9a0019e224cd7154438c23f2 ]

If a TX queue has no space for new TX frames, the driver will keep
these frames in the

wifi: iwlwifi: empty overflow queue during flush

[ Upstream commit 658939fc68d3241f9a0019e224cd7154438c23f2 ]

If a TX queue has no space for new TX frames, the driver will keep
these frames in the overflow queue, and during reclaim flow it
will retry to send the frames from that queue.
But if the reclaim flow was invoked from TX queue flush, we will also
TX these frames, which is wrong as we don't want to TX anything
after flush.
This might also cause assert 0x125F when removing the queue,
saying that the driver removes a non-empty queue
Fix this by TXing the overflow queue's frames only if we are
not in flush queue flow.

Fixes: a44509805895 ("iwlwifi: move reclaim flows to the queue file")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231022173519.caf06c8709d9.Ibf664ccb3f952e836f8fa461ea58fc08e5c46e88@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

wifi: iwlwifi: honor the enable_ini value

[ Upstream commit e0c1ca236e28e4263fba76d47a108ed95dcae33e ]

In case the user sets the enable_ini to some preset, we want to honor
the value.

Remove the o

wifi: iwlwifi: honor the enable_ini value

[ Upstream commit e0c1ca236e28e4263fba76d47a108ed95dcae33e ]

In case the user sets the enable_ini to some preset, we want to honor
the value.

Remove the ops to set the value of the module parameter is runtime, we
don't want to allow to modify the value in runtime since we configure
the firmware once at the beginning on its life.

Fixes: b49c2b252b58 ("iwlwifi: Configure FW debug preset via module param.")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230830112059.5734e0f374bb.I6698eda8ed2112378dd47ac5d62866ebe7a94f77@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

Merge drm/drm-fixes into drm-misc-fixes

Forwarding to v6.6-rc1.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>

Merge branch 'next' into for-linus

Prepare input updates for 6.6 merge window.

Merge tag 'net-next-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next

Pull networking updates from Paolo Abeni:
"Core:

- Increase size limits for to-be-sent skb frag allocat

Merge tag 'net-next-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next

Pull networking updates from Paolo Abeni:
"Core:

- Increase size limits for to-be-sent skb frag allocations. This
allows tun, tap devices and packet sockets to better cope with
large writes operations

- Store netdevs in an xarray, to simplify iterating over netdevs

- Refactor nexthop selection for multipath routes

- Improve sched class lifetime handling

- Add backup nexthop ID support for bridge

- Implement drop reasons support in openvswitch

- Several data races annotations and fixes

- Constify the sk parameter of routing functions

- Prepend kernel version to netconsole message

Protocols:

- Implement support for TCP probing the peer being under memory
pressure

- Remove hard coded limitation on IPv6 specific info placement inside
the socket struct

- Get rid of sysctl_tcp_adv_win_scale and use an auto-estimated per
socket scaling factor

- Scaling-up the IPv6 expired route GC via a separated list of
expiring routes

- In-kernel support for the TLS alert protocol

- Better support for UDP reuseport with connected sockets

- Add NEXT-C-SID support for SRv6 End.X behavior, reducing the SR
header size

- Get rid of additional ancillary per MPTCP connection struct socket

- Implement support for BPF-based MPTCP packet schedulers

- Format MPTCP subtests selftests results in TAP

- Several new SMC 2.1 features including unique experimental options,
max connections per lgr negotiation, max links per lgr negotiation

BPF:

- Multi-buffer support in AF_XDP

- Add multi uprobe BPF links for attaching multiple uprobes and usdt
probes, which is significantly faster and saves extra fds

- Implement an fd-based tc BPF attach API (TCX) and BPF link support
on top of it

- Add SO_REUSEPORT support for TC bpf_sk_assign

- Support new instructions from cpu v4 to simplify the generated code
and feature completeness, for x86, arm64, riscv64

- Support defragmenting IPv(4|6) packets in BPF

- Teach verifier actual bounds of bpf_get_smp_processor_id() and fix
perf+libbpf issue related to custom section handling

- Introduce bpf map element count and enable it for all program types

- Add a BPF hook in sys_socket() to change the protocol ID from
IPPROTO_TCP to IPPROTO_MPTCP to cover migration for legacy

- Introduce bpf_me_mcache_free_rcu() and fix OOM under stress

- Add uprobe support for the bpf_get_func_ip helper

- Check skb ownership against full socket

- Support for up to 12 arguments in BPF trampoline

- Extend link_info for kprobe_multi and perf_event links

Netfilter:

- Speed-up process exit by aborting ruleset validation if a fatal
signal is pending

- Allow NLA_POLICY_MASK to be used with BE16/BE32 types

Driver API:

- Page pool optimizations, to improve data locality and cache usage

- Introduce ndo_hwtstamp_get() and ndo_hwtstamp_set() to avoid the
need for raw ioctl() handling in drivers

- Simplify genetlink dump operations (doit/dumpit) providing them the
common information already populated in struct genl_info

- Extend and use the yaml devlink specs to [re]generate the split ops

- Introduce devlink selective dumps, to allow SF filtering SF based
on handle and other attributes

- Add yaml netlink spec for netlink-raw families, allow route, link
and address related queries via the ynl tool

- Remove phylink legacy mode support

- Support offload LED blinking to phy

- Add devlink port function attributes for IPsec

New hardware / drivers:

- Ethernet:
- Broadcom ASP 2.0 (72165) ethernet controller
- MediaTek MT7988 SoC
- Texas Instruments AM654 SoC
- Texas Instruments IEP driver
- Atheros qca8081 phy
- Marvell 88Q2110 phy
- NXP TJA1120 phy

- WiFi:
- MediaTek mt7981 support

- Can:
- Kvaser SmartFusion2 PCI Express devices
- Allwinner T113 controllers
- Texas Instruments tcan4552/4553 chips

- Bluetooth:
- Intel Gale Peak
- Qualcomm WCN3988 and WCN7850
- NXP AW693 and IW624
- Mediatek MT2925

Drivers:

- Ethernet NICs:
- nVidia/Mellanox:
- mlx5:
- support UDP encapsulation in packet offload mode
- IPsec packet offload support in eswitch mode
- improve aRFS observability by adding new set of counters
- extends MACsec offload support to cover RoCE traffic
- dynamic completion EQs
- mlx4:
- convert to use auxiliary bus instead of custom interface
logic
- Intel
- ice:
- implement switchdev bridge offload, even for LAG
interfaces
- implement SRIOV support for LAG interfaces
- igc:
- add support for multiple in-flight TX timestamps
- Broadcom:
- bnxt:
- use the unified RX page pool buffers for XDP and non-XDP
- use the NAPI skb allocation cache
- OcteonTX2:
- support Round Robin scheduling HTB offload
- TC flower offload support for SPI field
- Freescale:
- add XDP_TX feature support
- AMD:
- ionic: add support for PCI FLR event
- sfc:
- basic conntrack offload
- introduce eth, ipv4 and ipv6 pedit offloads
- ST Microelectronics:
- stmmac: maximze PTP timestamping resolution

- Virtual NICs:
- Microsoft vNIC:
- batch ringing RX queue doorbell on receiving packets
- add page pool for RX buffers
- Virtio vNIC:
- add per queue interrupt coalescing support
- Google vNIC:
- add queue-page-list mode support

- Ethernet high-speed switches:
- nVidia/Mellanox (mlxsw):
- add port range matching tc-flower offload
- permit enslavement to netdevices with uppers

- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- convert to phylink_pcs
- Renesas:
- r8A779fx: add speed change support
- rzn1: enables vlan support

- Ethernet PHYs:
- convert mv88e6xxx to phylink_pcs

- WiFi:
- Qualcomm Wi-Fi 7 (ath12k):
- extremely High Throughput (EHT) PHY support
- RealTek (rtl8xxxu):
- enable AP mode for: RTL8192FU, RTL8710BU (RTL8188GU),
RTL8192EU and RTL8723BU
- RealTek (rtw89):
- Introduce Time Averaged SAR (TAS) support

- Connector:
- support for event filtering"

* tag 'net-next-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1806 commits)
net: ethernet: mtk_wed: minor change in wed_{tx,rx}info_show
net: ethernet: mtk_wed: add some more info in wed_txinfo_show handler
net: stmmac: clarify difference between "interface" and "phy_interface"
r8152: add vendor/device ID pair for D-Link DUB-E250
devlink: move devlink_notify_register/unregister() to dev.c
devlink: move small_ops definition into netlink.c
devlink: move tracepoint definitions into core.c
devlink: push linecard related code into separate file
devlink: push rate related code into separate file
devlink: push trap related code into separate file
devlink: use tracepoint_enabled() helper
devlink: push region related code into separate file
devlink: push param related code into separate file
devlink: push resource related code into separate file
devlink: push dpipe related code into separate file
devlink: move and rename devlink_dpipe_send_and_alloc_skb() helper
devlink: push shared buffer related code into separate file
devlink: push port related code into separate file
devlink: push object register/unregister notifications into separate helpers
inet: fix IP_TRANSPARENT error handling
...

show more ...

Merge tag 'wireless-next-2023-08-25' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next

Kalle Valo says:

====================
wireless-next patches for v6.6

The second pull re

Merge tag 'wireless-next-2023-08-25' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next

Kalle Valo says:

====================
wireless-next patches for v6.6

The second pull request for v6.6, this time with both stack and driver
changes. Unusually we have only one major new feature but lots of
small cleanup all over, I guess this is due to people have been on
vacation the last month.

Major changes:

rtw89
- Introduce Time Averaged SAR (TAS) support

* tag 'wireless-next-2023-08-25' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (114 commits)
wifi: rtlwifi: rtl8723: Remove unused function rtl8723_cmd_send_packet()
wifi: rtw88: usb: kill and free rx urbs on probe failure
wifi: rtw89: Fix clang -Wimplicit-fallthrough in rtw89_query_sar()
wifi: rtw89: phy: modify register setting of ENV_MNTR, PHYSTS and DIG
wifi: rtw89: phy: add phy_gen_def::cr_base to support WiFi 7 chips
wifi: rtw89: mac: define register address of rx_filter to generalize code
wifi: rtw89: mac: define internal memory address for WiFi 7 chip
wifi: rtw89: mac: generalize code to indirectly access WiFi internal memory
wifi: rtw89: mac: add mac_gen_def::band1_offset to map MAC band1 register address
wifi: wlcore: sdio: Use module_sdio_driver macro to simplify the code
wifi: rtw89: initialize multi-channel handling
wifi: rtw89: provide functions to configure NoA for beacon update
wifi: rtw89: call rtw89_chan_get() by vif chanctx if aware of vif
wifi: rtw89: sar: let caller decide the center frequency to query
wifi: rtw89: refine rtw89_correct_cck_chan() by rtw89_hw_to_nl80211_band()
wifi: rtw89: add function prototype for coex request duration
Fix nomenclature for USB and PCI wireless devices
wifi: ath: Use is_multicast_ether_addr() to check multicast Ether address
wifi: ath12k: Remove unused declarations
wifi: ath12k: add check max message length while scanning with extraie
...
====================

Link: https://lore.kernel.org/r/20230825132230.A0833C433C8@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

wifi: iwlwifi: pcie: point invalid TFDs to invalid data

There are occasionally bugs which cause the device to try
to use a TFD that it wasn't supposed to, and these are
very hard to diagnose. Fill a

wifi: iwlwifi: pcie: point invalid TFDs to invalid data

There are occasionally bugs which cause the device to try
to use a TFD that it wasn't supposed to, and these are
very hard to diagnose. Fill all unused TFDs with a debug
command that immediately causes an error to be detected
in these cases.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230816104355.10a9af1ca91f.Ifc790d62c52b4bc9a74c9581610af498509f5759@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

show more ...

wifi: iwlwifi: remove WARN from read_mem32()

There's no reason to warn here, it's not an internal consistency
issue, we even use this to check if the device is dead, and if it
read_mem() returns an

wifi: iwlwifi: remove WARN from read_mem32()

There's no reason to warn here, it's not an internal consistency
issue, we even use this to check if the device is dead, and if it
read_mem() returns an error that's either because grab NIC access
or memory allocation failed, both of which are already noisy.

Just remove the warning entirely.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230816104355.5f4e80eb63cc.Iffd88f63f95575f28e503da13b473724e3341aee@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

show more ...

Merge drm/drm-next into drm-intel-next

Catching-up with drm-next and drm-intel-gt-next.
It will unblock a code refactor around the platform
definitions (names vs acronyms).

Signed-off-by: Rodrigo V

Merge drm/drm-next into drm-intel-next

Catching-up with drm-next and drm-intel-gt-next.
It will unblock a code refactor around the platform
definitions (names vs acronyms).

Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

show more ...

Merge drm/drm-next into drm-intel-gt-next

Need to pull in b3e4aae612ec ("drm/i915/hdcp: Modify hdcp_gsc_message msg sending mechanism") as
a dependency for https://patchwork.freedesktop.org/series/1

Merge drm/drm-next into drm-intel-gt-next

Need to pull in b3e4aae612ec ("drm/i915/hdcp: Modify hdcp_gsc_message msg sending mechanism") as
a dependency for https://patchwork.freedesktop.org/series/121735/

Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

show more ...

Merge drm/drm-next into drm-misc-next

Backmerging to get v6.5-rc2.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>

Merge tag 'v6.4' into next

Sync up with mainline to bring in updates to shared infrastructure.

ASoC: Merge v6.5-rc2

Get a similar baseline to my other branches, and fixes for people using
the branch.

Merge v6.5-rc1 into drm-misc-fixes

Boris needs 6.5-rc1 in drm-misc-fixes to prevent a conflict.

Signed-off-by: Maxime Ripard <mripard@kernel.org>

Merge branch 'master' into mm-hotfixes-stable

Merge tag 'net-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next

Pull networking changes from Jakub Kicinski:
"WiFi 7 and sendpage changes are the biggest pieces of work fo

Merge tag 'net-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next

Pull networking changes from Jakub Kicinski:
"WiFi 7 and sendpage changes are the biggest pieces of work for this
release. The latter will definitely require fixes but I think that we
got it to a reasonable point.

Core:

- Rework the sendpage & splice implementations

Instead of feeding data into sockets page by page extend sendmsg
handlers to support taking a reference on the data, controlled by a
new flag called MSG_SPLICE_PAGES

Rework the handling of unexpected-end-of-file to invoke an
additional callback instead of trying to predict what the right
combination of MORE/NOTLAST flags is

Remove the MSG_SENDPAGE_NOTLAST flag completely

- Implement SCM_PIDFD, a new type of CMSG type analogous to
SCM_CREDENTIALS, but it contains pidfd instead of plain pid

- Enable socket busy polling with CONFIG_RT

- Improve reliability and efficiency of reporting for ref_tracker

- Auto-generate a user space C library for various Netlink families

Protocols:

- Allow TCP to shrink the advertised window when necessary, prevent
sk_rcvbuf auto-tuning from growing the window all the way up to
tcp_rmem[2]

- Use per-VMA locking for "page-flipping" TCP receive zerocopy

- Prepare TCP for device-to-device data transfers, by making sure
that payloads are always attached to skbs as page frags

- Make the backoff time for the first N TCP SYN retransmissions
linear. Exponential backoff is unnecessarily conservative

- Create a new MPTCP getsockopt to retrieve all info
(MPTCP_FULL_INFO)

- Avoid waking up applications using TLS sockets until we have a full
record

- Allow using kernel memory for protocol ioctl callbacks, paving the
way to issuing ioctls over io_uring

- Add nolocalbypass option to VxLAN, forcing packets to be fully
encapsulated even if they are destined for a local IP address

- Make TCPv4 use consistent hash in TIME_WAIT and SYN_RECV. Ensure
in-kernel ECMP implementation (e.g. Open vSwitch) select the same
link for all packets. Support L4 symmetric hashing in Open vSwitch

- PPPoE: make number of hash bits configurable

- Allow DNS to be overwritten by DHCPACK in the in-kernel DHCP client
(ipconfig)

- Add layer 2 miss indication and filtering, allowing higher layers
(e.g. ACL filters) to make forwarding decisions based on whether
packet matched forwarding state in lower devices (bridge)

- Support matching on Connectivity Fault Management (CFM) packets

- Hide the "link becomes ready" IPv6 messages by demoting their
printk level to debug

- HSR: don't enable promiscuous mode if device offloads the proto

- Support active scanning in IEEE 802.15.4

- Continue work on Multi-Link Operation for WiFi 7

BPF:

- Add precision propagation for subprogs and callbacks. This allows
maintaining verification efficiency when subprograms are used, or
in fact passing the verifier at all for complex programs,
especially those using open-coded iterators

- Improve BPF's {g,s}setsockopt() length handling. Previously BPF
assumed the length is always equal to the amount of written data.
But some protos allow passing a NULL buffer to discover what the
output buffer *should* be, without writing anything

- Accept dynptr memory as memory arguments passed to helpers

- Add routing table ID to bpf_fib_lookup BPF helper

- Support O_PATH FDs in BPF_OBJ_PIN and BPF_OBJ_GET commands

- Drop bpf_capable() check in BPF_MAP_FREEZE command (used to mark
maps as read-only)

- Show target_{obj,btf}_id in tracing link fdinfo

- Addition of several new kfuncs (most of the names are
self-explanatory):
- Add a set of new dynptr kfuncs: bpf_dynptr_adjust(),
bpf_dynptr_is_null(), bpf_dynptr_is_rdonly(), bpf_dynptr_size()
and bpf_dynptr_clone().
- bpf_task_under_cgroup()
- bpf_sock_destroy() - force closing sockets
- bpf_cpumask_first_and(), rework bpf_cpumask_any*() kfuncs

Netfilter:

- Relax set/map validation checks in nf_tables. Allow checking
presence of an entry in a map without using the value

- Increase ip_vs_conn_tab_bits range for 64BIT builds

- Allow updating size of a set

- Improve NAT tuple selection when connection is closing

Driver API:

- Integrate netdev with LED subsystem, to allow configuring HW
"offloaded" blinking of LEDs based on link state and activity
(i.e. packets coming in and out)

- Support configuring rate selection pins of SFP modules

- Factor Clause 73 auto-negotiation code out of the drivers, provide
common helper routines

- Add more fool-proof helpers for managing lifetime of MDIO devices
associated with the PCS layer

- Allow drivers to report advanced statistics related to Time Aware
scheduler offload (taprio)

- Allow opting out of VF statistics in link dump, to allow more VFs
to fit into the message

- Split devlink instance and devlink port operations

New hardware / drivers:

- Ethernet:
- Synopsys EMAC4 IP support (stmmac)
- Marvell 88E6361 8 port (5x1GE + 3x2.5GE) switches
- Marvell 88E6250 7 port switches
- Microchip LAN8650/1 Rev.B0 PHYs
- MediaTek MT7981/MT7988 built-in 1GE PHY driver

- WiFi:
- Realtek RTL8192FU, 2.4 GHz, b/g/n mode, 2T2R, 300 Mbps
- Realtek RTL8723DS (SDIO variant)
- Realtek RTL8851BE

- CAN:
- Fintek F81604

Drivers:

- Ethernet NICs:
- Intel (100G, ice):
- support dynamic interrupt allocation
- use meta data match instead of VF MAC addr on slow-path
- nVidia/Mellanox:
- extend link aggregation to handle 4, rather than just 2 ports
- spawn sub-functions without any features by default
- OcteonTX2:
- support HTB (Tx scheduling/QoS) offload
- make RSS hash generation configurable
- support selecting Rx queue using TC filters
- Wangxun (ngbe/txgbe):
- add basic Tx/Rx packet offloads
- add phylink support (SFP/PCS control)
- Freescale/NXP (enetc):
- report TAPRIO packet statistics
- Solarflare/AMD:
- support matching on IP ToS and UDP source port of outer
header
- VxLAN and GENEVE tunnel encapsulation over IPv4 or IPv6
- add devlink dev info support for EF10

- Virtual NICs:
- Microsoft vNIC:
- size the Rx indirection table based on requested
configuration
- support VLAN tagging
- Amazon vNIC:
- try to reuse Rx buffers if not fully consumed, useful for ARM
servers running with 16kB pages
- Google vNIC:
- support TCP segmentation of >64kB frames

- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- enable USXGMII (88E6191X)
- Microchip:
- lan966x: add support for Egress Stage 0 ACL engine
- lan966x: support mapping packet priority to internal switch
priority (based on PCP or DSCP)

- Ethernet PHYs:
- Broadcom PHYs:
- support for Wake-on-LAN for BCM54210E/B50212E
- report LPI counter
- Microsemi PHYs: support RGMII delay configuration (VSC85xx)
- Micrel PHYs: receive timestamp in the frame (LAN8841)
- Realtek PHYs: support optional external PHY clock
- Altera TSE PCS: merge the driver into Lynx PCS which it is a
variant of

- CAN: Kvaser PCIEcan:
- support packet timestamping

- WiFi:
- Intel (iwlwifi):
- major update for new firmware and Multi-Link Operation (MLO)
- configuration rework to drop test devices and split the
different families
- support for segmented PNVM images and power tables
- new vendor entries for PPAG (platform antenna gain) feature
- Qualcomm 802.11ax (ath11k):
- Multiple Basic Service Set Identifier (MBSSID) and Enhanced
MBSSID Advertisement (EMA) support in AP mode
- support factory test mode
- RealTek (rtw89):
- add RSSI based antenna diversity
- support U-NII-4 channels on 5 GHz band
- RealTek (rtl8xxxu):
- AP mode support for 8188f
- support USB RX aggregation for the newer chips"

* tag 'net-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1602 commits)
net: scm: introduce and use scm_recv_unix helper
af_unix: Skip SCM_PIDFD if scm->pid is NULL.
net: lan743x: Simplify comparison
netlink: Add __sock_i_ino() for __netlink_diag_dump().
net: dsa: avoid suspicious RCU usage for synced VLAN-aware MAC addresses
Revert "af_unix: Call scm_recv() only after scm_set_cred()."
phylink: ReST-ify the phylink_pcs_neg_mode() kdoc
libceph: Partially revert changes to support MSG_SPLICE_PAGES
net: phy: mscc: fix packet loss due to RGMII delays
net: mana: use vmalloc_array and vcalloc
net: enetc: use vmalloc_array and vcalloc
ionic: use vmalloc_array and vcalloc
pds_core: use vmalloc_array and vcalloc
gve: use vmalloc_array and vcalloc
octeon_ep: use vmalloc_array and vcalloc
net: usb: qmi_wwan: add u-blox 0x1312 composition
perf trace: fix MSG_SPLICE_PAGES build error
ipvlan: Fix return value of ipvlan_queue_xmit()
netfilter: nf_tables: fix underflow in chain reference counter
netfilter: nf_tables: unbind non-anonymous set if rule construction fails
...

show more ...

Merge tag 'wireless-next-2023-06-22' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next

Johannes Berg says:

====================
Notable changes this time around:

MAINTAINERS

Merge tag 'wireless-next-2023-06-22' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next

Johannes Berg says:

====================
Notable changes this time around:

MAINTAINERS
- add missing driver git trees

ath11k
- factory test mode support

iwlwifi
- config rework to drop test devices and
split the different families
- major update for new firmware and MLO

stack
- initial multi-link reconfiguration suppor
- multi-BSSID and MLO improvements

other
- fix the last few W=1 warnings from GCC 13
- merged wireless tree to avoid conflicts

* tag 'wireless-next-2023-06-22' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (245 commits)
wifi: ieee80211: fix erroneous NSTR bitmap size checks
wifi: rtlwifi: cleanup USB interface
wifi: rtlwifi: simplify LED management
wifi: ath10k: improve structure padding
wifi: ath9k: convert msecs to jiffies where needed
wifi: iwlwifi: mvm: Add support for IGTK in D3 resume flow
wifi: iwlwifi: mvm: update two most recent GTKs on D3 resume flow
wifi: iwlwifi: mvm: Refactor security key update after D3
wifi: mac80211: mark keys as uploaded when added by the driver
wifi: iwlwifi: remove support of A0 version of FM RF
wifi: iwlwifi: cfg: clean up Bz module firmware lines
wifi: iwlwifi: pcie: add device id 51F1 for killer 1675
wifi: iwlwifi: bump FW API to 83 for AX/BZ/SC devices
wifi: iwlwifi: cfg: remove trailing dash from FW_PRE constants
wifi: iwlwifi: also unify Ma device configurations
wifi: iwlwifi: also unify Sc device configurations
wifi: iwlwifi: unify Bz/Gl device configurations
wifi: iwlwifi: pcie: also drop jacket from info macro
wifi: iwlwifi: remove support for *nJ devices
wifi: iwlwifi: don't load old firmware for 22000
...
====================

Link: https://lore.kernel.org/r/20230622185602.147650-2-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

wifi: iwlwifi: limit EHT capabilities based on PCIe link speed

If a discrete NIC is connected to a PCIe link hat isn't at least
Gen3 (8.0 GT/s), then we cannot sustain 320 MHz traffic, so remove
tha

wifi: iwlwifi: limit EHT capabilities based on PCIe link speed

If a discrete NIC is connected to a PCIe link hat isn't at least
Gen3 (8.0 GT/s), then we cannot sustain 320 MHz traffic, so remove
that from EHT capabilities in that case.

While at it, also move setting 320 MHz beamformee to the right
place in the code so it's not set while not supporting 320 MHz.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230620125813.b77a1574a0a7.Id4120c161fb7df6dedc70d5f3e3829e9117b8cb1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

show more ...

Merge drm/drm-next into drm-misc-next-fixes

Backmerging to sync drm-misc-next-fixes with drm-misc-next.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>

wifi: iwlwifi: unify checks for HW error values

The hardware, depending on which part fails or times out,
returns 0xA5A5A5A. or 0x5A5A5A5. with the lowest 4 bits
encoding some further reason/status.

wifi: iwlwifi: unify checks for HW error values

The hardware, depending on which part fails or times out,
returns 0xA5A5A5A. or 0x5A5A5A5. with the lowest 4 bits
encoding some further reason/status. However, mostly we
don't really need to care about the exact reasons, so
unify the checks for this to avoid hardcoding those magic
values all over the driver.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230612184434.3e2959741a38.I1c297a53787b87e4e2b8f296c041921338573f4d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

show more ...