Merge tag 'v6.6.45' into for/openbmc/dev-6.6

This is the 6.6.45 stable release

net: phy: realtek: add support for RTL8366S Gigabit PHY

[ Upstream commit 225990c487c1023e7b3aa89beb6a68011fbc0461 ]

The PHY built in to the Realtek RTL8366S switch controller was
previously suppor

net: phy: realtek: add support for RTL8366S Gigabit PHY

[ Upstream commit 225990c487c1023e7b3aa89beb6a68011fbc0461 ]

The PHY built in to the Realtek RTL8366S switch controller was
previously supported by genphy_driver. This PHY does not implement MMD
operations. Since commit 9b01c885be36 ("net: phy: c22: migrate to
genphy_c45_write_eee_adv()"), MMD register reads have been made during
phy_probe to determine EEE support. For genphy_driver, these reads are
transformed into 802.3 annex 22D clause 45-over-clause 22
mmd_phy_indirect operations that perform MII register writes to
MII_MMD_CTRL and MII_MMD_DATA. This overwrites those two MII registers,
which on this PHY are reserved and have another function, rendering the
PHY unusable while so configured.

Proper support for this PHY is restored by providing a phy_driver that
declares MMD operations as unsupported by using the helper functions
provided for that purpose, while remaining otherwise identical to
genphy_driver.

Fixes: 9b01c885be36 ("net: phy: c22: migrate to genphy_c45_write_eee_adv()")
Reported-by: Russell Senior <russell@personaltelco.net>
Closes: https://github.com/openwrt/openwrt/issues/15981
Link: https://github.com/openwrt/openwrt/issues/15739
Signed-off-by: Mark Mentovai <mark@mentovai.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

Merge tag 'v6.6.19' into dev-6.6

This is the 6.6.19 stable release

net: phy: realtek: Fix rtl8211f_config_init() for RTL8211F(D)(I)-VD-CG PHY

[ Upstream commit 3489182b11d35f1944c1245fc9c4867cf622c50f ]

Commit bb726b753f75 ("net: phy: realtek: add support for
RTL8

net: phy: realtek: Fix rtl8211f_config_init() for RTL8211F(D)(I)-VD-CG PHY

[ Upstream commit 3489182b11d35f1944c1245fc9c4867cf622c50f ]

Commit bb726b753f75 ("net: phy: realtek: add support for
RTL8211F(D)(I)-VD-CG") extended support of the driver from the existing
support for RTL8211F(D)(I)-CG PHY to the newer RTL8211F(D)(I)-VD-CG PHY.

While that commit indicated that the RTL8211F_PHYCR2 register is not
supported by the "VD-CG" PHY model and therefore updated the corresponding
section in rtl8211f_config_init() to be invoked conditionally, the call to
"genphy_soft_reset()" was left as-is, when it should have also been invoked
conditionally. This is because the call to "genphy_soft_reset()" was first
introduced by the commit 0a4355c2b7f8 ("net: phy: realtek: add dt property
to disable CLKOUT clock") since the RTL8211F guide indicates that a PHY
reset should be issued after setting bits in the PHYCR2 register.

As the PHYCR2 register is not applicable to the "VD-CG" PHY model, fix the
rtl8211f_config_init() function by invoking "genphy_soft_reset()"
conditionally based on the presence of the "PHYCR2" register.

Fixes: bb726b753f75 ("net: phy: realtek: add support for RTL8211F(D)(I)-VD-CG")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240220070007.968762-1-s-vadapalli@ti.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

Merge drm/drm-next into drm-intel-next

Catching-up with drm-next and drm-intel-gt-next.
It will unblock a code refactor around the platform
definitions (names vs acronyms).

Signed-off-by: Rodrigo V

Merge drm/drm-next into drm-intel-next

Catching-up with drm-next and drm-intel-gt-next.
It will unblock a code refactor around the platform
definitions (names vs acronyms).

Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

show more ...

Merge drm/drm-next into drm-intel-gt-next

Need to pull in b3e4aae612ec ("drm/i915/hdcp: Modify hdcp_gsc_message msg sending mechanism") as
a dependency for https://patchwork.freedesktop.org/series/1

Merge drm/drm-next into drm-intel-gt-next

Need to pull in b3e4aae612ec ("drm/i915/hdcp: Modify hdcp_gsc_message msg sending mechanism") as
a dependency for https://patchwork.freedesktop.org/series/121735/

Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

show more ...

Merge drm/drm-next into drm-misc-next

Backmerging to get v6.5-rc2.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>

ASoC: Merge v6.5-rc2

Get a similar baseline to my other branches, and fixes for people using
the branch.

Merge v6.5-rc1 into drm-misc-fixes

Boris needs 6.5-rc1 in drm-misc-fixes to prevent a conflict.

Signed-off-by: Maxime Ripard <mripard@kernel.org>

Merge branch 'master' into mm-hotfixes-stable

Merge tag 'net-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next

Pull networking changes from Jakub Kicinski:
"WiFi 7 and sendpage changes are the biggest pieces of work fo

Merge tag 'net-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next

Pull networking changes from Jakub Kicinski:
"WiFi 7 and sendpage changes are the biggest pieces of work for this
release. The latter will definitely require fixes but I think that we
got it to a reasonable point.

Core:

- Rework the sendpage & splice implementations

Instead of feeding data into sockets page by page extend sendmsg
handlers to support taking a reference on the data, controlled by a
new flag called MSG_SPLICE_PAGES

Rework the handling of unexpected-end-of-file to invoke an
additional callback instead of trying to predict what the right
combination of MORE/NOTLAST flags is

Remove the MSG_SENDPAGE_NOTLAST flag completely

- Implement SCM_PIDFD, a new type of CMSG type analogous to
SCM_CREDENTIALS, but it contains pidfd instead of plain pid

- Enable socket busy polling with CONFIG_RT

- Improve reliability and efficiency of reporting for ref_tracker

- Auto-generate a user space C library for various Netlink families

Protocols:

- Allow TCP to shrink the advertised window when necessary, prevent
sk_rcvbuf auto-tuning from growing the window all the way up to
tcp_rmem[2]

- Use per-VMA locking for "page-flipping" TCP receive zerocopy

- Prepare TCP for device-to-device data transfers, by making sure
that payloads are always attached to skbs as page frags

- Make the backoff time for the first N TCP SYN retransmissions
linear. Exponential backoff is unnecessarily conservative

- Create a new MPTCP getsockopt to retrieve all info
(MPTCP_FULL_INFO)

- Avoid waking up applications using TLS sockets until we have a full
record

- Allow using kernel memory for protocol ioctl callbacks, paving the
way to issuing ioctls over io_uring

- Add nolocalbypass option to VxLAN, forcing packets to be fully
encapsulated even if they are destined for a local IP address

- Make TCPv4 use consistent hash in TIME_WAIT and SYN_RECV. Ensure
in-kernel ECMP implementation (e.g. Open vSwitch) select the same
link for all packets. Support L4 symmetric hashing in Open vSwitch

- PPPoE: make number of hash bits configurable

- Allow DNS to be overwritten by DHCPACK in the in-kernel DHCP client
(ipconfig)

- Add layer 2 miss indication and filtering, allowing higher layers
(e.g. ACL filters) to make forwarding decisions based on whether
packet matched forwarding state in lower devices (bridge)

- Support matching on Connectivity Fault Management (CFM) packets

- Hide the "link becomes ready" IPv6 messages by demoting their
printk level to debug

- HSR: don't enable promiscuous mode if device offloads the proto

- Support active scanning in IEEE 802.15.4

- Continue work on Multi-Link Operation for WiFi 7

BPF:

- Add precision propagation for subprogs and callbacks. This allows
maintaining verification efficiency when subprograms are used, or
in fact passing the verifier at all for complex programs,
especially those using open-coded iterators

- Improve BPF's {g,s}setsockopt() length handling. Previously BPF
assumed the length is always equal to the amount of written data.
But some protos allow passing a NULL buffer to discover what the
output buffer *should* be, without writing anything

- Accept dynptr memory as memory arguments passed to helpers

- Add routing table ID to bpf_fib_lookup BPF helper

- Support O_PATH FDs in BPF_OBJ_PIN and BPF_OBJ_GET commands

- Drop bpf_capable() check in BPF_MAP_FREEZE command (used to mark
maps as read-only)

- Show target_{obj,btf}_id in tracing link fdinfo

- Addition of several new kfuncs (most of the names are
self-explanatory):
- Add a set of new dynptr kfuncs: bpf_dynptr_adjust(),
bpf_dynptr_is_null(), bpf_dynptr_is_rdonly(), bpf_dynptr_size()
and bpf_dynptr_clone().
- bpf_task_under_cgroup()
- bpf_sock_destroy() - force closing sockets
- bpf_cpumask_first_and(), rework bpf_cpumask_any*() kfuncs

Netfilter:

- Relax set/map validation checks in nf_tables. Allow checking
presence of an entry in a map without using the value

- Increase ip_vs_conn_tab_bits range for 64BIT builds

- Allow updating size of a set

- Improve NAT tuple selection when connection is closing

Driver API:

- Integrate netdev with LED subsystem, to allow configuring HW
"offloaded" blinking of LEDs based on link state and activity
(i.e. packets coming in and out)

- Support configuring rate selection pins of SFP modules

- Factor Clause 73 auto-negotiation code out of the drivers, provide
common helper routines

- Add more fool-proof helpers for managing lifetime of MDIO devices
associated with the PCS layer

- Allow drivers to report advanced statistics related to Time Aware
scheduler offload (taprio)

- Allow opting out of VF statistics in link dump, to allow more VFs
to fit into the message

- Split devlink instance and devlink port operations

New hardware / drivers:

- Ethernet:
- Synopsys EMAC4 IP support (stmmac)
- Marvell 88E6361 8 port (5x1GE + 3x2.5GE) switches
- Marvell 88E6250 7 port switches
- Microchip LAN8650/1 Rev.B0 PHYs
- MediaTek MT7981/MT7988 built-in 1GE PHY driver

- WiFi:
- Realtek RTL8192FU, 2.4 GHz, b/g/n mode, 2T2R, 300 Mbps
- Realtek RTL8723DS (SDIO variant)
- Realtek RTL8851BE

- CAN:
- Fintek F81604

Drivers:

- Ethernet NICs:
- Intel (100G, ice):
- support dynamic interrupt allocation
- use meta data match instead of VF MAC addr on slow-path
- nVidia/Mellanox:
- extend link aggregation to handle 4, rather than just 2 ports
- spawn sub-functions without any features by default
- OcteonTX2:
- support HTB (Tx scheduling/QoS) offload
- make RSS hash generation configurable
- support selecting Rx queue using TC filters
- Wangxun (ngbe/txgbe):
- add basic Tx/Rx packet offloads
- add phylink support (SFP/PCS control)
- Freescale/NXP (enetc):
- report TAPRIO packet statistics
- Solarflare/AMD:
- support matching on IP ToS and UDP source port of outer
header
- VxLAN and GENEVE tunnel encapsulation over IPv4 or IPv6
- add devlink dev info support for EF10

- Virtual NICs:
- Microsoft vNIC:
- size the Rx indirection table based on requested
configuration
- support VLAN tagging
- Amazon vNIC:
- try to reuse Rx buffers if not fully consumed, useful for ARM
servers running with 16kB pages
- Google vNIC:
- support TCP segmentation of >64kB frames

- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- enable USXGMII (88E6191X)
- Microchip:
- lan966x: add support for Egress Stage 0 ACL engine
- lan966x: support mapping packet priority to internal switch
priority (based on PCP or DSCP)

- Ethernet PHYs:
- Broadcom PHYs:
- support for Wake-on-LAN for BCM54210E/B50212E
- report LPI counter
- Microsemi PHYs: support RGMII delay configuration (VSC85xx)
- Micrel PHYs: receive timestamp in the frame (LAN8841)
- Realtek PHYs: support optional external PHY clock
- Altera TSE PCS: merge the driver into Lynx PCS which it is a
variant of

- CAN: Kvaser PCIEcan:
- support packet timestamping

- WiFi:
- Intel (iwlwifi):
- major update for new firmware and Multi-Link Operation (MLO)
- configuration rework to drop test devices and split the
different families
- support for segmented PNVM images and power tables
- new vendor entries for PPAG (platform antenna gain) feature
- Qualcomm 802.11ax (ath11k):
- Multiple Basic Service Set Identifier (MBSSID) and Enhanced
MBSSID Advertisement (EMA) support in AP mode
- support factory test mode
- RealTek (rtw89):
- add RSSI based antenna diversity
- support U-NII-4 channels on 5 GHz band
- RealTek (rtl8xxxu):
- AP mode support for 8188f
- support USB RX aggregation for the newer chips"

* tag 'net-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1602 commits)
net: scm: introduce and use scm_recv_unix helper
af_unix: Skip SCM_PIDFD if scm->pid is NULL.
net: lan743x: Simplify comparison
netlink: Add __sock_i_ino() for __netlink_diag_dump().
net: dsa: avoid suspicious RCU usage for synced VLAN-aware MAC addresses
Revert "af_unix: Call scm_recv() only after scm_set_cred()."
phylink: ReST-ify the phylink_pcs_neg_mode() kdoc
libceph: Partially revert changes to support MSG_SPLICE_PAGES
net: phy: mscc: fix packet loss due to RGMII delays
net: mana: use vmalloc_array and vcalloc
net: enetc: use vmalloc_array and vcalloc
ionic: use vmalloc_array and vcalloc
pds_core: use vmalloc_array and vcalloc
gve: use vmalloc_array and vcalloc
octeon_ep: use vmalloc_array and vcalloc
net: usb: qmi_wwan: add u-blox 0x1312 composition
perf trace: fix MSG_SPLICE_PAGES build error
ipvlan: Fix return value of ipvlan_queue_xmit()
netfilter: nf_tables: fix underflow in chain reference counter
netfilter: nf_tables: unbind non-anonymous set if rule construction fails
...

show more ...

Merge branch 'realtek-external-phy-clock'

Detlev Casanova says:

====================
net: phy: realtek: Support external PHY clock

Some PHYs can use an external clock that must be enabled before
c

Merge branch 'realtek-external-phy-clock'

Detlev Casanova says:

====================
net: phy: realtek: Support external PHY clock

Some PHYs can use an external clock that must be enabled before
communicating with them.

Changes since v3:
* Do not call genphy_suspend if WoL is enabled.
Changes since v2:
* Reword documentation commit message
Changes since v1:
* Remove the clock name as it is not guaranteed to be identical across
different PHYs
* Disable/Enable the clock when suspending/resuming
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: realtek: Disable clock on suspend

For PHYs that call rtl821x_probe() where an external clock can be
configured, make sure that the clock is disabled
when ->suspend() is called and enabled

net: phy: realtek: Disable clock on suspend

For PHYs that call rtl821x_probe() where an external clock can be
configured, make sure that the clock is disabled
when ->suspend() is called and enabled on resume.

The PHY_ALWAYS_CALL_SUSPEND is added to ensure that the suspend function
is actually always called.

Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: realtek: Add optional external PHY clock

In some cases, the PHY can use an external clock source instead of a
crystal.

Add an optional clock in the phy node to make sure that the clock so

net: phy: realtek: Add optional external PHY clock

In some cases, the PHY can use an external clock source instead of a
crystal.

Add an optional clock in the phy node to make sure that the clock source
is enabled, if specified, before probing.

Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

Merge branch 'main' into zstd-linus

Merge branch 'next' into for-linus

Prepare input updates for 6.2 merge window.

Merge drm/drm-next into drm-misc-next-fixes

Backmerging to update drm-misc-next-fixes for the final phase
of the release cycle.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>

Merge drm/drm-next into drm-intel-next

Catch up on 6.1-rc cycle in order to solve the intel_backlight
conflict on linux-next.

Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

Merge drm/drm-next into drm-intel-gt-next

Needed to bring in v6.1-rc1 which contains commit f683b9d61319 ("i915: use the VMA iterator")
which is needed for series https://patchwork.freedesktop.org/s

Merge drm/drm-next into drm-intel-gt-next

Needed to bring in v6.1-rc1 which contains commit f683b9d61319 ("i915: use the VMA iterator")
which is needed for series https://patchwork.freedesktop.org/series/110083/ .

Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

show more ...

Merge branch 'main' into zstd-next

Merge drm/drm-fixes into drm-misc-fixes

Backmerging to get v6.1-rc1.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>

ASoC: jz4752b: Capture fixes

Merge series from Siarhei Volkau <lis8215@gmail.com>:

The patchset fixes:
- Line In path stays powered off during capturing or
bypass to mixer.
- incorrectly repre

ASoC: jz4752b: Capture fixes

Merge series from Siarhei Volkau <lis8215@gmail.com>:

The patchset fixes:
- Line In path stays powered off during capturing or
bypass to mixer.
- incorrectly represented dB values in alsamixer, et al.
- incorrect represented Capture input selector in alsamixer
in Playback tab.
- wrong control selected as Capture Master

show more ...

Merge drm/drm-next into drm-misc-next

Let's kick-off this release cycle.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>

Merge tag 'v6.1-rc1' into next

Merge with mainline to bring in the latest changes to twl4030 driver.

Merge branch 'master' into mm-hotfixes-stable