Merge tag 'v6.6.48' into for/openbmc/dev-6.6

This is the 6.6.48 stable release

igc: Fix qbv tx latency by setting gtxoffset

commit 6c3fc0b1c3d073bd6fc3bf43dbd0e64240537464 upstream.

A large tx latency issue was discovered during testing when only QBV was
enabled. The issue oc

igc: Fix qbv tx latency by setting gtxoffset

commit 6c3fc0b1c3d073bd6fc3bf43dbd0e64240537464 upstream.

A large tx latency issue was discovered during testing when only QBV was
enabled. The issue occurs because gtxoffset was not set when QBV is
active, it was only set when launch time is active.

The patch "igc: Correct the launchtime offset" only sets gtxoffset when
the launchtime_enable field is set by the user. Enabling launchtime_enable
ultimately sets the register IGC_TXQCTL_QUEUE_MODE_LAUNCHT (referred to as
LaunchT in the SW user manual).

Section 7.5.2.6 of the IGC i225/6 SW User Manual Rev 1.2.4 states:
"The latency between transmission scheduling (launch time) and the
time the packet is transmitted to the network is listed in Table 7-61."

However, the patch misinterprets the phrase "launch time" in that section
by assuming it specifically refers to the LaunchT register, whereas it
actually denotes the generic term for when a packet is released from the
internal buffer to the MAC transmit logic.

This launch time, as per that section, also implicitly refers to the QBV
gate open time, where a packet waits in the buffer for the QBV gate to
open. Therefore, latency applies whenever QBV is in use. TSN features such
as QBU and QAV reuse QBV, making the latency universal to TSN features.

Discussed with i226 HW owner (Shalev, Avi) and we were in agreement that
the term "launch time" used in Section 7.5.2.6 is not clear and can be
easily misinterpreted. Avi will update this section to:
"When TQAVCTRL.TRANSMIT_MODE = TSN, the latency between transmission
scheduling and the time the packet is transmitted to the network is listed
in Table 7-61."

Fix this issue by using igc_tsn_is_tx_mode_in_tsn() as a condition to
write to gtxoffset, aligning with the newly updated SW User Manual.

Tested:
1. Enrol taprio on talker board
base-time 0
cycle-time 1000000
flags 0x2
index 0 cmd S gatemask 0x1 interval1
index 0 cmd S gatemask 0x1 interval2

Note:
interval1 = interval for a 64 bytes packet to go through
interval2 = cycle-time - interval1

2. Take tcpdump on listener board

3. Use udp tai app on talker to send packets to listener

4. Check the timestamp on listener via wireshark

Test Result:
100 Mbps: 113 ~193 ns
1000 Mbps: 52 ~ 84 ns
2500 Mbps: 95 ~ 223 ns

Note that the test result is similar to the patch "igc: Correct the
launchtime offset".

Fixes: 790835fcc0cb ("igc: Correct the launchtime offset")
Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

igc: Fix reset adapter logics when tx mode change

[ Upstream commit 0afeaeb5dae86aceded0d5f0c3a54d27858c0c6f ]

Following the "igc: Fix TX Hang issue when QBV Gate is close" changes,
remaining issue

igc: Fix reset adapter logics when tx mode change

[ Upstream commit 0afeaeb5dae86aceded0d5f0c3a54d27858c0c6f ]

Following the "igc: Fix TX Hang issue when QBV Gate is close" changes,
remaining issues with the reset adapter logic in igc_tsn_offload_apply()
have been observed:

1. The reset adapter logics for i225 and i226 differ, although they should
be the same according to the guidelines in I225/6 HW Design Section
7.5.2.1 on software initialization during tx mode changes.
2. The i225 resets adapter every time, even though tx mode doesn't change.
This occurs solely based on the condition igc_is_device_id_i225() when
calling schedule_work().
3. i226 doesn't reset adapter for tsn->legacy tx mode changes. It only
resets adapter for legacy->tsn tx mode transitions.
4. qbv_count introduced in the patch is actually not needed; in this
context, a non-zero value of qbv_count is used to indicate if tx mode
was unconditionally set to tsn in igc_tsn_enable_offload(). This could
be replaced by checking the existing register
IGC_TQAVCTRL_TRANSMIT_MODE_TSN bit.

This patch resolves all issues and enters schedule_work() to reset the
adapter only when changing tx mode. It also removes reliance on qbv_count.

qbv_count field will be removed in a future patch.

Test ran:

1. Verify reset adapter behaviour in i225/6:
a) Enrol a new GCL
Reset adapter observed (tx mode change legacy->tsn)
b) Enrol a new GCL without deleting qdisc
No reset adapter observed (tx mode remain tsn->tsn)
c) Delete qdisc
Reset adapter observed (tx mode change tsn->legacy)

2. Tested scenario from "igc: Fix TX Hang issue when QBV Gate is closed"
to confirm it remains resolved.

Fixes: 175c241288c0 ("igc: Fix TX Hang issue when QBV Gate is closed")
Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

igc: Fix qbv_config_change_errors logics

[ Upstream commit f8d6acaee9d35cbff3c3cfad94641666c596f8da ]

When user issues these cmds:
1. Either a) or b)
a) mqprio with hardware offload disabled

igc: Fix qbv_config_change_errors logics

[ Upstream commit f8d6acaee9d35cbff3c3cfad94641666c596f8da ]

When user issues these cmds:
1. Either a) or b)
a) mqprio with hardware offload disabled
b) taprio with txtime-assist feature enabled
2. etf
3. tc qdisc delete
4. taprio with base time in the past

At step 4, qbv_config_change_errors wrongly increased by 1.

Excerpt from IEEE 802.1Q-2018 8.6.9.3.1:
"If AdminBaseTime specifies a time in the past, and the current schedule
is running, then: Increment ConfigChangeError counter"

qbv_config_change_errors should only increase if base time is in the past
and no taprio is active. In user perspective, taprio was not active when
first triggered at step 4. However, i225/6 reuses qbv for etf, so qbv is
enabled with a dummy schedule at step 2 where it enters
igc_tsn_enable_offload() and qbv_count got incremented to 1. At step 4, it
enters igc_tsn_enable_offload() again, qbv_count is incremented to 2.
Because taprio is running, tc_setup_type is TC_SETUP_QDISC_ETF and
qbv_count > 1, qbv_config_change_errors value got incremented.

This issue happens due to reliance on qbv_count field where a non-zero
value indicates that taprio is running. But qbv_count increases
regardless if taprio is triggered by user or by other tsn feature. It does
not align with qbv_config_change_errors expectation where it is only
concerned with taprio triggered by user.

Fixing this by relocating the qbv_config_change_errors logic to
igc_save_qbv_schedule(), eliminating reliance on qbv_count and its
inaccuracies from i225/6's multiple uses of qbv feature for other TSN
features.

The new function created: igc_tsn_is_taprio_activated_by_user() uses
taprio_offload_enable field to indicate that the current running taprio
was triggered by user, instead of triggered by non-qbv feature like etf.

Fixes: ae4fe4698300 ("igc: Add qbv_config_change_errors counter")
Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

igc: Fix packet still tx after gate close by reducing i226 MAC retry buffer

[ Upstream commit e037a26ead187901f83cad9c503ccece5ff6817a ]

Testing uncovered that even when the taprio gate is closed,

igc: Fix packet still tx after gate close by reducing i226 MAC retry buffer

[ Upstream commit e037a26ead187901f83cad9c503ccece5ff6817a ]

Testing uncovered that even when the taprio gate is closed, some packets
still transmit.

According to i225/6 hardware errata [1], traffic might overflow the
planned QBV window. This happens because MAC maintains an internal buffer,
primarily for supporting half duplex retries. Therefore, even when the
gate closes, residual MAC data in the buffer may still transmit.

To mitigate this for i226, reduce the MAC's internal buffer from 192 bytes
to the recommended 88 bytes by modifying the RETX_CTL register value.

This follows guidelines from:
[1] Ethernet Controller I225/I22 Spec Update Rev 2.1 Errata Item 9:
TSN: Packet Transmission Might Cross Qbv Window
[2] I225/6 SW User Manual Rev 1.2.4: Section 8.11.5 Retry Buffer Control

Note that the RETX_CTL register can't be used in TSN mode because half
duplex feature cannot coexist with TSN.

Test Steps:
1. Send taprio cmd to board A:
tc qdisc replace dev enp1s0 parent root handle 100 taprio \
num_tc 4 \
map 3 2 1 0 3 3 3 3 3 3 3 3 3 3 3 3 \
queues 1@0 1@1 1@2 1@3 \
base-time 0 \
sched-entry S 0x07 500000 \
sched-entry S 0x0f 500000 \
flags 0x2 \
txtime-delay 0

Note that for TC3, gate should open for 500us and close for another
500us.

3. Take tcpdump log on Board B.

4. Send udp packets via UDP tai app from Board A to Board B.

5. Analyze tcpdump log via wireshark log on Board B. Ensure that the
total time from the first to the last packet received during one cycle
for TC3 does not exceed 500us.

Fixes: 43546211738e ("igc: Add new device ID's")
Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

Merge tag 'v6.6.11' into dev-6.6

This is the 6.6.11 stable release

igc: Fix hicredit calculation

[ Upstream commit 947dfc8138dfaeb6e966e2d661de89eb203e3064 ]

According to the Intel Software Manual for I225, Section 7.5.2.7,
hicredit should be multiplied by the con

igc: Fix hicredit calculation

[ Upstream commit 947dfc8138dfaeb6e966e2d661de89eb203e3064 ]

According to the Intel Software Manual for I225, Section 7.5.2.7,
hicredit should be multiplied by the constant link-rate value, 0x7736.

Currently, the old constant link-rate value, 0x7735, from the boards
supported on igb are being used, most likely due to a copy'n'paste, as
the rest of the logic is the same for both drivers.

Update hicredit accordingly.

Fixes: 1ab011b0bf07 ("igc: Add support for CBS offloading")
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Rodrigo Cataldo <rodrigo.cadore@l-acoustics.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

Merge drm/drm-fixes into drm-misc-fixes

Forwarding to v6.6-rc1.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>

Merge branch 'next' into for-linus

Prepare input updates for 6.6 merge window.

Merge tag 'vfs-6.6-merge-2' of ssh://gitolite.kernel.org/pub/scm/fs/xfs/xfs-linux

Pull filesystem freezing updates from Darrick Wong:

New code for 6.6:

* Allow the kernel to initiate a freeze of

Merge tag 'vfs-6.6-merge-2' of ssh://gitolite.kernel.org/pub/scm/fs/xfs/xfs-linux

Pull filesystem freezing updates from Darrick Wong:

New code for 6.6:

* Allow the kernel to initiate a freeze of a filesystem. The kernel
and userspace can both hold a freeze on a filesystem at the same
time; the freeze is not lifted until /both/ holders lift it. This
will enable us to fix a longstanding bug in XFS online fsck.

Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Message-Id: <20230822182604.GB11286@frogsfrogsfrogs>
Signed-off-by: Christian Brauner <brauner@kernel.org>

show more ...

Merge tag 'v6.5-rc6' into icc-next

The fixes that got merged into v6.5-rc6 are needed here.

Signed-off-by: Georgi Djakov <djakov@kernel.org>

Merge drm/drm-next into drm-intel-next

Catching-up with drm-next and drm-intel-gt-next.
It will unblock a code refactor around the platform
definitions (names vs acronyms).

Signed-off-by: Rodrigo V

Merge drm/drm-next into drm-intel-next

Catching-up with drm-next and drm-intel-gt-next.
It will unblock a code refactor around the platform
definitions (names vs acronyms).

Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

show more ...

Merge drm/drm-next into drm-intel-gt-next

Need to pull in b3e4aae612ec ("drm/i915/hdcp: Modify hdcp_gsc_message msg sending mechanism") as
a dependency for https://patchwork.freedesktop.org/series/1

Merge drm/drm-next into drm-intel-gt-next

Need to pull in b3e4aae612ec ("drm/i915/hdcp: Modify hdcp_gsc_message msg sending mechanism") as
a dependency for https://patchwork.freedesktop.org/series/121735/

Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

show more ...

Merge drm/drm-next into drm-misc-next

Backmerging to get v6.5-rc2.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>

regulator: Merge up fixes from mainline

There's several things here that will really help my CI.

regmap: Merge up fixes from mainline

There's several things here that will really help my CI.

spi: Merge up fixes from mainline

There's several things here that will really help my CI.

Merge tag 'asoc-fix-v6.5-rc1-2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus

ASoC: Fixes for v6.5

A few more fixes for v6.5, just small driver specific ones.

Merge tag 'v6.5-rc2' into sched/core, to pick up fixes

Sync with upstream fixes before applying EEVDF.

Signed-off-by: Ingo Molnar <mingo@kernel.org>

ASoC: Improve coverage in default KUnit runs

Merge series from Mark Brown <broonie@kernel.org>:

We have some KUnit tests for ASoC but they're not being run as much as
they should be since ASoC isn'

ASoC: Improve coverage in default KUnit runs

Merge series from Mark Brown <broonie@kernel.org>:

We have some KUnit tests for ASoC but they're not being run as much as
they should be since ASoC isn't enabled in the configs used by default
with KUnit and in the case of the topology tests there is no way to
enable them without enabling drivers that use them. This series
provides a Kconfig option which KUnit can use directly rather than worry
about drivers.

Further, since KUnit is typically run in UML but ALSA prevents build
with UML we need to remove that Kconfig conflict. As far as I can tell
the motiviation for this is that many ALSA drivers use iomem APIs which
are not available under UML and it's more trouble than it's worth to go
through and add per driver dependencies. In order to avoid these issues
we also provide stubs for these APIs so there are no build time issues
if a driver relies on iomem but does not depend on it. With these stubs
I am able to build all the sound drivers available in a UML defconfig
(UML allmodconfig appears to have substantial other issues in a quick
test).

With this series I am able to run the topology KUnit tests as part of a
kunit --alltests run.

show more ...

Merge branch 'topic/hda-pci-ids' into for-next

Pull cleanup of HD-audio PCI IDs.

Signed-off-by: Takashi Iwai <tiwai@suse.de>

Merge tag 'v6.4' into next

Sync up with mainline to bring in updates to shared infrastructure.

ASoC: Merge v6.5-rc2

Get a similar baseline to my other branches, and fixes for people using
the branch.

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

Cross-merge networking fixes after downstream PR.

No conflicts or adjacent changes.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'net-6.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

Pull networking fixes from Paolo Abeni:
"Including fixes from netfilter, wireless and ebpf.

Current release -

Merge tag 'net-6.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

Pull networking fixes from Paolo Abeni:
"Including fixes from netfilter, wireless and ebpf.

Current release - regressions:

- netfilter: conntrack: gre: don't set assured flag for clash entries

- wifi: iwlwifi: remove 'use_tfh' config to fix crash

Previous releases - regressions:

- ipv6: fix a potential refcount underflow for idev

- icmp6: ifix null-ptr-deref of ip6_null_entry->rt6i_idev in
icmp6_dev()

- bpf: fix max stack depth check for async callbacks

- eth: mlx5e:
- check for NOT_READY flag state after locking
- fix page_pool page fragment tracking for XDP

- eth: igc:
- fix tx hang issue when QBV gate is closed
- fix corner cases for TSN offload

- eth: octeontx2-af: Move validation of ptp pointer before its usage

- eth: ena: fix shift-out-of-bounds in exponential backoff

Previous releases - always broken:

- core: prevent skb corruption on frag list segmentation

- sched:
- cls_fw: fix improper refcount update leads to use-after-free
- sch_qfq: account for stab overhead in qfq_enqueue

- netfilter:
- report use refcount overflow
- prevent OOB access in nft_byteorder_eval

- wifi: mt7921e: fix init command fail with enabled device

- eth: ocelot: fix oversize frame dropping for preemptible TCs

- eth: fec: recycle pages for transmitted XDP frames"

* tag 'net-6.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (79 commits)
selftests: tc-testing: add test for qfq with stab overhead
net/sched: sch_qfq: account for stab overhead in qfq_enqueue
selftests: tc-testing: add tests for qfq mtu sanity check
net/sched: sch_qfq: reintroduce lmax bound check for MTU
wifi: cfg80211: fix receiving mesh packets without RFC1042 header
wifi: rtw89: debug: fix error code in rtw89_debug_priv_send_h2c_set()
net: txgbe: fix eeprom calculation error
net/sched: make psched_mtu() RTNL-less safe
net: ena: fix shift-out-of-bounds in exponential backoff
netdevsim: fix uninitialized data in nsim_dev_trap_fa_cookie_write()
net/sched: flower: Ensure both minimum and maximum ports are specified
MAINTAINERS: Add another mailing list for QUALCOMM ETHQOS ETHERNET DRIVER
docs: netdev: update the URL of the status page
wifi: iwlwifi: remove 'use_tfh' config to fix crash
xdp: use trusted arguments in XDP hints kfuncs
bpf: cpumap: Fix memory leak in cpu_map_update_elem
wifi: airo: avoid uninitialized warning in airo_get_rate()
octeontx2-pf: Add additional check for MCAM rules
net: dsa: Removed unneeded of_node_put in felix_parse_ports_node
net: fec: use netdev_err_once() instead of netdev_err()
...

show more ...