Merge tag 'v6.6.67' into for/openbmc/dev-6.6

This is the 6.6.67 stable release

net: dsa: felix: fix stuck CPU-injected packets with short taprio windows

[ Upstream commit acfcdb78d5d4cdb78e975210c8825b9a112463f6 ]

With this port schedule:

tc qdisc replace dev $send_if parent

net: dsa: felix: fix stuck CPU-injected packets with short taprio windows

[ Upstream commit acfcdb78d5d4cdb78e975210c8825b9a112463f6 ]

With this port schedule:

tc qdisc replace dev $send_if parent root handle 100 taprio \
num_tc 8 queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
map 0 1 2 3 4 5 6 7 \
base-time 0 cycle-time 10000 \
sched-entry S 01 1250 \
sched-entry S 02 1250 \
sched-entry S 04 1250 \
sched-entry S 08 1250 \
sched-entry S 10 1250 \
sched-entry S 20 1250 \
sched-entry S 40 1250 \
sched-entry S 80 1250 \
flags 2

ptp4l would fail to take TX timestamps of Pdelay_Resp messages like this:

increasing tx_timestamp_timeout may correct this issue, but it is likely caused by a driver bug
ptp4l[4134.168]: port 2: send peer delay response failed

It turns out that the driver can't take their TX timestamps because it
can't transmit them in the first place. And there's nothing special
about the Pdelay_Resp packets - they're just regular 68 byte packets.
But with this taprio configuration, the switch would refuse to send even
the ETH_ZLEN minimum packet size.

This should have definitely not been the case. When applying the taprio
config, the driver prints:

mscc_felix 0000:00:00.5: port 0 tc 0 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 1 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 2 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 3 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 4 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 5 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 6 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 7 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS

and thus, everything under 132 bytes - ETH_FCS_LEN should have been sent
without problems. Yet it's not.

For the forwarding path, the configuration is fine, yet packets injected
from Linux get stuck with this schedule no matter what.

The first hint that the static guard bands are the cause of the problem
is that reverting Michael Walle's commit 297c4de6f780 ("net: dsa: felix:
re-enable TAS guard band mode") made things work. It must be that the
guard bands are calculated incorrectly.

I remembered that there is a magic constant in the driver, set to 33 ns
for no logical reason other than experimentation, which says "never let
the static guard bands get so large as to leave less than this amount of
remaining space in the time slot, because the queue system will refuse
to schedule packets otherwise, and they will get stuck". I had a hunch
that my previous experimentally-determined value was only good for
packets coming from the forwarding path, and that the CPU injection path
needed more.

I came to the new value of 35 ns through binary search, after seeing
that with 544 ns (the bit time required to send the Pdelay_Resp packet
at gigabit) it works. Again, this is purely experimental, there's no
logic and the manual doesn't say anything.

The new driver prints for this schedule look like this:

mscc_felix 0000:00:00.5: port 0 tc 0 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 1 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 2 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 3 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 4 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 5 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 6 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 7 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS

So yes, the maximum MTU is now even smaller by 1 byte than before.
This is maybe counter-intuitive, but makes more sense with a diagram of
one time slot.

Before:

Gate open Gate close
| |
v 1250 ns total time slot duration v
<---------------------------------------------------->
<----><---------------------------------------------->
33 ns 1217 ns static guard band
useful

Gate open Gate close
| |
v 1250 ns total time slot duration v
<---------------------------------------------------->
<-----><--------------------------------------------->
35 ns 1215 ns static guard band
useful

The static guard band implemented by this switch hardware directly
determines the maximum allowable MTU for that traffic class. The larger
it is, the earlier the switch will stop scheduling frames for
transmission, because otherwise they might overrun the gate close time
(and avoiding that is the entire purpose of Michael's patch).
So, we now have guard bands smaller by 2 ns, thus, in this particular
case, we lose a byte of the maximum MTU.

Fixes: 11afdc6526de ("net: dsa: felix: tc-taprio intervals smaller than MTU should send at least one packet")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Link: https://patch.msgid.link/20241210132640.3426788-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

Merge tag 'v6.6.52' into for/openbmc/dev-6.6

This is the 6.6.52 stable release

net: dsa: felix: ignore pending status of TAS module when it's disabled

[ Upstream commit 70654f4c212e83898feced125d91ebb3695950d8 ]

The TAS module could not be configured when it's running in pend

net: dsa: felix: ignore pending status of TAS module when it's disabled

[ Upstream commit 70654f4c212e83898feced125d91ebb3695950d8 ]

The TAS module could not be configured when it's running in pending
status. We need disable the module and configure it again. However, the
pending status is not cleared after the module disabled. TC taprio set
will always return busy even it's disabled.

For example, a user uses tc-taprio to configure Qbv and a future
basetime. The TAS module will run in a pending status. There is no way
to reconfigure Qbv, it always returns busy.

Actually the TAS module can be reconfigured when it's disabled. So it
doesn't need to check the pending status if the TAS module is disabled.

After the patch, user can delete the tc taprio configuration to disable
Qbv and reconfigure it again.

Fixes: de143c0e274b ("net: dsa: felix: Configure Time-Aware Scheduler via taprio offload")
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Link: https://patch.msgid.link/20240906093550.29985-1-xiaoliang.yang_1@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

Merge drm/drm-fixes into drm-misc-fixes

Forwarding to v6.6-rc1.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>

Merge branch 'next' into for-linus

Prepare input updates for 6.6 merge window.

Merge tag 'net-next-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next

Pull networking updates from Paolo Abeni:
"Core:

- Increase size limits for to-be-sent skb frag allocat

Merge tag 'net-next-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next

Pull networking updates from Paolo Abeni:
"Core:

- Increase size limits for to-be-sent skb frag allocations. This
allows tun, tap devices and packet sockets to better cope with
large writes operations

- Store netdevs in an xarray, to simplify iterating over netdevs

- Refactor nexthop selection for multipath routes

- Improve sched class lifetime handling

- Add backup nexthop ID support for bridge

- Implement drop reasons support in openvswitch

- Several data races annotations and fixes

- Constify the sk parameter of routing functions

- Prepend kernel version to netconsole message

Protocols:

- Implement support for TCP probing the peer being under memory
pressure

- Remove hard coded limitation on IPv6 specific info placement inside
the socket struct

- Get rid of sysctl_tcp_adv_win_scale and use an auto-estimated per
socket scaling factor

- Scaling-up the IPv6 expired route GC via a separated list of
expiring routes

- In-kernel support for the TLS alert protocol

- Better support for UDP reuseport with connected sockets

- Add NEXT-C-SID support for SRv6 End.X behavior, reducing the SR
header size

- Get rid of additional ancillary per MPTCP connection struct socket

- Implement support for BPF-based MPTCP packet schedulers

- Format MPTCP subtests selftests results in TAP

- Several new SMC 2.1 features including unique experimental options,
max connections per lgr negotiation, max links per lgr negotiation

BPF:

- Multi-buffer support in AF_XDP

- Add multi uprobe BPF links for attaching multiple uprobes and usdt
probes, which is significantly faster and saves extra fds

- Implement an fd-based tc BPF attach API (TCX) and BPF link support
on top of it

- Add SO_REUSEPORT support for TC bpf_sk_assign

- Support new instructions from cpu v4 to simplify the generated code
and feature completeness, for x86, arm64, riscv64

- Support defragmenting IPv(4|6) packets in BPF

- Teach verifier actual bounds of bpf_get_smp_processor_id() and fix
perf+libbpf issue related to custom section handling

- Introduce bpf map element count and enable it for all program types

- Add a BPF hook in sys_socket() to change the protocol ID from
IPPROTO_TCP to IPPROTO_MPTCP to cover migration for legacy

- Introduce bpf_me_mcache_free_rcu() and fix OOM under stress

- Add uprobe support for the bpf_get_func_ip helper

- Check skb ownership against full socket

- Support for up to 12 arguments in BPF trampoline

- Extend link_info for kprobe_multi and perf_event links

Netfilter:

- Speed-up process exit by aborting ruleset validation if a fatal
signal is pending

- Allow NLA_POLICY_MASK to be used with BE16/BE32 types

Driver API:

- Page pool optimizations, to improve data locality and cache usage

- Introduce ndo_hwtstamp_get() and ndo_hwtstamp_set() to avoid the
need for raw ioctl() handling in drivers

- Simplify genetlink dump operations (doit/dumpit) providing them the
common information already populated in struct genl_info

- Extend and use the yaml devlink specs to [re]generate the split ops

- Introduce devlink selective dumps, to allow SF filtering SF based
on handle and other attributes

- Add yaml netlink spec for netlink-raw families, allow route, link
and address related queries via the ynl tool

- Remove phylink legacy mode support

- Support offload LED blinking to phy

- Add devlink port function attributes for IPsec

New hardware / drivers:

- Ethernet:
- Broadcom ASP 2.0 (72165) ethernet controller
- MediaTek MT7988 SoC
- Texas Instruments AM654 SoC
- Texas Instruments IEP driver
- Atheros qca8081 phy
- Marvell 88Q2110 phy
- NXP TJA1120 phy

- WiFi:
- MediaTek mt7981 support

- Can:
- Kvaser SmartFusion2 PCI Express devices
- Allwinner T113 controllers
- Texas Instruments tcan4552/4553 chips

- Bluetooth:
- Intel Gale Peak
- Qualcomm WCN3988 and WCN7850
- NXP AW693 and IW624
- Mediatek MT2925

Drivers:

- Ethernet NICs:
- nVidia/Mellanox:
- mlx5:
- support UDP encapsulation in packet offload mode
- IPsec packet offload support in eswitch mode
- improve aRFS observability by adding new set of counters
- extends MACsec offload support to cover RoCE traffic
- dynamic completion EQs
- mlx4:
- convert to use auxiliary bus instead of custom interface
logic
- Intel
- ice:
- implement switchdev bridge offload, even for LAG
interfaces
- implement SRIOV support for LAG interfaces
- igc:
- add support for multiple in-flight TX timestamps
- Broadcom:
- bnxt:
- use the unified RX page pool buffers for XDP and non-XDP
- use the NAPI skb allocation cache
- OcteonTX2:
- support Round Robin scheduling HTB offload
- TC flower offload support for SPI field
- Freescale:
- add XDP_TX feature support
- AMD:
- ionic: add support for PCI FLR event
- sfc:
- basic conntrack offload
- introduce eth, ipv4 and ipv6 pedit offloads
- ST Microelectronics:
- stmmac: maximze PTP timestamping resolution

- Virtual NICs:
- Microsoft vNIC:
- batch ringing RX queue doorbell on receiving packets
- add page pool for RX buffers
- Virtio vNIC:
- add per queue interrupt coalescing support
- Google vNIC:
- add queue-page-list mode support

- Ethernet high-speed switches:
- nVidia/Mellanox (mlxsw):
- add port range matching tc-flower offload
- permit enslavement to netdevices with uppers

- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- convert to phylink_pcs
- Renesas:
- r8A779fx: add speed change support
- rzn1: enables vlan support

- Ethernet PHYs:
- convert mv88e6xxx to phylink_pcs

- WiFi:
- Qualcomm Wi-Fi 7 (ath12k):
- extremely High Throughput (EHT) PHY support
- RealTek (rtl8xxxu):
- enable AP mode for: RTL8192FU, RTL8710BU (RTL8188GU),
RTL8192EU and RTL8723BU
- RealTek (rtw89):
- Introduce Time Averaged SAR (TAS) support

- Connector:
- support for event filtering"

* tag 'net-next-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1806 commits)
net: ethernet: mtk_wed: minor change in wed_{tx,rx}info_show
net: ethernet: mtk_wed: add some more info in wed_txinfo_show handler
net: stmmac: clarify difference between "interface" and "phy_interface"
r8152: add vendor/device ID pair for D-Link DUB-E250
devlink: move devlink_notify_register/unregister() to dev.c
devlink: move small_ops definition into netlink.c
devlink: move tracepoint definitions into core.c
devlink: push linecard related code into separate file
devlink: push rate related code into separate file
devlink: push trap related code into separate file
devlink: use tracepoint_enabled() helper
devlink: push region related code into separate file
devlink: push param related code into separate file
devlink: push resource related code into separate file
devlink: push dpipe related code into separate file
devlink: move and rename devlink_dpipe_send_and_alloc_skb() helper
devlink: push shared buffer related code into separate file
devlink: push port related code into separate file
devlink: push object register/unregister notifications into separate helpers
inet: fix IP_TRANSPARENT error handling
...

show more ...

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

Cross-merge networking fixes after downstream PR.

Conflicts:

include/net/inet_sock.h
f866fbc842de ("ipv4: fix data-races around ine

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

Cross-merge networking fixes after downstream PR.

Conflicts:

include/net/inet_sock.h
f866fbc842de ("ipv4: fix data-races around inet->inet_id")
c274af224269 ("inet: introduce inet->inet_flags")
https://lore.kernel.org/all/679ddff6-db6e-4ff6-b177-574e90d0103d@tessares.net/

Adjacent changes:

drivers/net/bonding/bond_alb.c
e74216b8def3 ("bonding: fix macvlan over alb bond support")
f11e5bd159b0 ("bonding: support balance-alb with openvswitch")

drivers/net/ethernet/broadcom/bgmac.c
d6499f0b7c7c ("net: bgmac: Return PTR_ERR() for fixed_phy_register()")
23a14488ea58 ("net: bgmac: Fix return value check for fixed_phy_register()")

drivers/net/ethernet/broadcom/genet/bcmmii.c
32bbe64a1386 ("net: bcmgenet: Fix return value check for fixed_phy_register()")
acf50d1adbf4 ("net: bcmgenet: Return PTR_ERR() for fixed_phy_register()")

net/sctp/socket.c
f866fbc842de ("ipv4: fix data-races around inet->inet_id")
b09bde5c3554 ("inet: move inet->mc_loop to inet->inet_frags")

Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

Merge tag 'net-6.5-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

Pull networking fixes from Paolo Abeni:
"Including fixes from wifi, can and netfilter.

Fixes to fixes:

- n

Merge tag 'net-6.5-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

Pull networking fixes from Paolo Abeni:
"Including fixes from wifi, can and netfilter.

Fixes to fixes:

- nf_tables:
- GC transaction race with abort path
- defer gc run if previous batch is still pending

Previous releases - regressions:

- ipv4: fix data-races around inet->inet_id

- phy: fix deadlocking in phy_error() invocation

- mdio: fix C45 read/write protocol

- ipvlan: fix a reference count leak warning in ipvlan_ns_exit()

- ice: fix NULL pointer deref during VF reset

- i40e: fix potential NULL pointer dereferencing of pf->vf in
i40e_sync_vsi_filters()

- tg3: use slab_build_skb() when needed

- mtk_eth_soc: fix NULL pointer on hw reset

Previous releases - always broken:

- core: validate veth and vxcan peer ifindexes

- sched: fix a qdisc modification with ambiguous command request

- devlink: add missing unregister linecard notification

- wifi: mac80211: limit reorder_buf_filtered to avoid UBSAN warning

- batman:
- do not get eth header before batadv_check_management_packet
- fix batadv_v_ogm_aggr_send memory leak

- bonding: fix macvlan over alb bond support

- mlxsw: set time stamp fields also when its type is MIRROR_UTC"

* tag 'net-6.5-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (54 commits)
selftests: bonding: add macvlan over bond testing
selftest: bond: add new topo bond_topo_2d1c.sh
bonding: fix macvlan over alb bond support
rtnetlink: Reject negative ifindexes in RTM_NEWLINK
netfilter: nf_tables: defer gc run if previous batch is still pending
netfilter: nf_tables: fix out of memory error handling
netfilter: nf_tables: use correct lock to protect gc_list
netfilter: nf_tables: GC transaction race with abort path
netfilter: nf_tables: flush pending destroy work before netlink notifier
netfilter: nf_tables: validate all pending tables
ibmveth: Use dcbf rather than dcbfl
i40e: fix potential NULL pointer dereferencing of pf->vf i40e_sync_vsi_filters()
net/sched: fix a qdisc modification with ambiguous command request
igc: Fix the typo in the PTM Control macro
batman-adv: Hold rtnl lock during MTU update via netlink
igb: Avoid starting unnecessary workqueues
can: raw: add missing refcount for memory leak fix
can: isotp: fix support for transmission of SF without flow control
bnx2x: new flag for track HW resource allocation
sfc: allocate a big enough SKB for loopback selftest packet
...

show more ...

Merge tag 'vfs-6.6-merge-2' of ssh://gitolite.kernel.org/pub/scm/fs/xfs/xfs-linux

Pull filesystem freezing updates from Darrick Wong:

New code for 6.6:

* Allow the kernel to initiate a freeze of

Merge tag 'vfs-6.6-merge-2' of ssh://gitolite.kernel.org/pub/scm/fs/xfs/xfs-linux

Pull filesystem freezing updates from Darrick Wong:

New code for 6.6:

* Allow the kernel to initiate a freeze of a filesystem. The kernel
and userspace can both hold a freeze on a filesystem at the same
time; the freeze is not lifted until /both/ holders lift it. This
will enable us to fix a longstanding bug in XFS online fsck.

Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Message-Id: <20230822182604.GB11286@frogsfrogsfrogs>
Signed-off-by: Christian Brauner <brauner@kernel.org>

show more ...

Merge tag 'v6.5-rc6' into icc-next

The fixes that got merged into v6.5-rc6 are needed here.

Signed-off-by: Georgi Djakov <djakov@kernel.org>

net: dsa: felix: fix oversize frame dropping for always closed tc-taprio gates

The blamed commit resolved a bug where frames would still get stuck at
egress, even though they're smaller than the max

net: dsa: felix: fix oversize frame dropping for always closed tc-taprio gates

The blamed commit resolved a bug where frames would still get stuck at
egress, even though they're smaller than the maxSDU[tc], because the
driver did not take into account the extra 33 ns that the queue system
needs for scheduling the frame.

It now takes that into account, but the arithmetic that we perform in
vsc9959_tas_remaining_gate_len_ps() is buggy, because we operate on
64-bit unsigned integers, so gate_len_ns - VSC9959_TAS_MIN_GATE_LEN_NS
may become a very large integer if gate_len_ns < 33 ns.

In practice, this means that we've introduced a regression where all
traffic class gates which are permanently closed will not get detected
by the driver, and we won't enable oversize frame dropping for them.

Before:
mscc_felix 0000:00:00.5: port 0: max frame size 1526 needs 12400000 ps, 1152000 ps for mPackets at speed 1000
mscc_felix 0000:00:00.5: port 0 tc 0 min gate len 1000000, sending all frames
mscc_felix 0000:00:00.5: port 0 tc 1 min gate len 0, sending all frames
mscc_felix 0000:00:00.5: port 0 tc 2 min gate len 0, sending all frames
mscc_felix 0000:00:00.5: port 0 tc 3 min gate len 0, sending all frames
mscc_felix 0000:00:00.5: port 0 tc 4 min gate len 0, sending all frames
mscc_felix 0000:00:00.5: port 0 tc 5 min gate len 0, sending all frames
mscc_felix 0000:00:00.5: port 0 tc 6 min gate len 0, sending all frames
mscc_felix 0000:00:00.5: port 0 tc 7 min gate length 5120 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 615 octets including FCS

After:
mscc_felix 0000:00:00.5: port 0: max frame size 1526 needs 12400000 ps, 1152000 ps for mPackets at speed 1000
mscc_felix 0000:00:00.5: port 0 tc 0 min gate len 1000000, sending all frames
mscc_felix 0000:00:00.5: port 0 tc 1 min gate length 0 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 1 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 2 min gate length 0 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 1 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 3 min gate length 0 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 1 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 4 min gate length 0 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 1 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 5 min gate length 0 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 1 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 6 min gate length 0 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 1 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 7 min gate length 5120 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 615 octets including FCS

Fixes: 11afdc6526de ("net: dsa: felix: tc-taprio intervals smaller than MTU should send at least one packet")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230817120111.3522827-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

Merge drm/drm-next into drm-intel-next

Catching-up with drm-next and drm-intel-gt-next.
It will unblock a code refactor around the platform
definitions (names vs acronyms).

Signed-off-by: Rodrigo V

Merge drm/drm-next into drm-intel-next

Catching-up with drm-next and drm-intel-gt-next.
It will unblock a code refactor around the platform
definitions (names vs acronyms).

Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

show more ...

Merge drm/drm-next into drm-intel-gt-next

Need to pull in b3e4aae612ec ("drm/i915/hdcp: Modify hdcp_gsc_message msg sending mechanism") as
a dependency for https://patchwork.freedesktop.org/series/1

Merge drm/drm-next into drm-intel-gt-next

Need to pull in b3e4aae612ec ("drm/i915/hdcp: Modify hdcp_gsc_message msg sending mechanism") as
a dependency for https://patchwork.freedesktop.org/series/121735/

Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

show more ...

net: flow_dissector: Use 64bits for used_keys

As 32bits of dissector->used_keys are exhausted,
increase the size to 64bits.

This is base change for ESP/AH flow dissector patch.
Please find patch an

net: flow_dissector: Use 64bits for used_keys

As 32bits of dissector->used_keys are exhausted,
increase the size to 64bits.

This is base change for ESP/AH flow dissector patch.
Please find patch and discussions at
https://lore.kernel.org/netdev/ZMDNjD46BvZ5zp5I@corigine.com/T/#t

Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Tested-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Martin Habets <habetsm.xilinx@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: dsa: Explicitly include correct DT includes

The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of tha

net: dsa: Explicitly include correct DT includes

The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.

Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230724211859.805481-1-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

Merge drm/drm-next into drm-misc-next

Backmerging to get v6.5-rc2.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>

regulator: Merge up fixes from mainline

There's several things here that will really help my CI.

regmap: Merge up fixes from mainline

There's several things here that will really help my CI.

spi: Merge up fixes from mainline

There's several things here that will really help my CI.

Merge tag 'asoc-fix-v6.5-rc1-2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus

ASoC: Fixes for v6.5

A few more fixes for v6.5, just small driver specific ones.

Merge tag 'v6.5-rc2' into sched/core, to pick up fixes

Sync with upstream fixes before applying EEVDF.

Signed-off-by: Ingo Molnar <mingo@kernel.org>

ASoC: Improve coverage in default KUnit runs

Merge series from Mark Brown <broonie@kernel.org>:

We have some KUnit tests for ASoC but they're not being run as much as
they should be since ASoC isn'

ASoC: Improve coverage in default KUnit runs

Merge series from Mark Brown <broonie@kernel.org>:

We have some KUnit tests for ASoC but they're not being run as much as
they should be since ASoC isn't enabled in the configs used by default
with KUnit and in the case of the topology tests there is no way to
enable them without enabling drivers that use them. This series
provides a Kconfig option which KUnit can use directly rather than worry
about drivers.

Further, since KUnit is typically run in UML but ALSA prevents build
with UML we need to remove that Kconfig conflict. As far as I can tell
the motiviation for this is that many ALSA drivers use iomem APIs which
are not available under UML and it's more trouble than it's worth to go
through and add per driver dependencies. In order to avoid these issues
we also provide stubs for these APIs so there are no build time issues
if a driver relies on iomem but does not depend on it. With these stubs
I am able to build all the sound drivers available in a UML defconfig
(UML allmodconfig appears to have substantial other issues in a quick
test).

With this series I am able to run the topology KUnit tests as part of a
kunit --alltests run.

show more ...

Merge branch 'topic/hda-pci-ids' into for-next

Pull cleanup of HD-audio PCI IDs.

Signed-off-by: Takashi Iwai <tiwai@suse.de>

Merge tag 'v6.4' into next

Sync up with mainline to bring in updates to shared infrastructure.