| ea3a6938 | 29-Jul-2024 |
Bryan O'Donoghue <bryan.odonoghue@linaro.org> |
media: qcom: camss: Fix ordering of pm_runtime_enable
commit a151766bd3688f6803e706c6433a7c8d3c6a6a94 upstream.
pm_runtime_enable() should happen prior to vfe_get() since vfe_get() calls
pm_runtime
media: qcom: camss: Fix ordering of pm_runtime_enable
commit a151766bd3688f6803e706c6433a7c8d3c6a6a94 upstream.
pm_runtime_enable() should happen prior to vfe_get() since vfe_get() calls
pm_runtime_resume_and_get().
This is a basic race condition that doesn't show up for most users so is
not widely reported. If you blacklist qcom-camss in modules.d and then
subsequently modprobe the module post-boot it is possible to reliably show
this error up.
The kernel log for this error looks like this:
qcom-camss ac5a000.camss: Failed to power up pipeline: -13
Fixes: 02afa816dbbf ("media: camss: Add basic runtime PM support")
Reported-by: Johan Hovold <johan+linaro@kernel.org>
Closes: https://lore.kernel.org/lkml/ZoVNHOTI0PKMNt4_@hovoldconsulting.com/
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Konrad Dybcio <konradybcio@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
show more ...
|
| 88a884de | 30-Aug-2023 |
Bryan O'Donoghue <bryan.odonoghue@linaro.org> |
media: qcom: camss: Fix genpd cleanup
[ Upstream commit f69791c39745e64621216fe8919cb73c0065002b ]
Right now we never release the power-domains properly on the error path.
Add a routine to be reuse
media: qcom: camss: Fix genpd cleanup
[ Upstream commit f69791c39745e64621216fe8919cb73c0065002b ]
Right now we never release the power-domains properly on the error path.
Add a routine to be reused for this purpose and appropriate jumps in
probe() to run that routine where necessary.
Fixes: 2f6f8af67203 ("media: camss: Refactor VFE power domain toggling")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
show more ...
|
| ed9f1ea9 | 30-Aug-2023 |
Andrey Konovalov <andrey.konovalov@linaro.org> |
media: qcom: camss: Fix csid-gen2 for test pattern generator
commit 87889f1b7ea40d2544b49c62092e6ef2792dced7 upstream.
In the current driver csid Test Pattern Generator (TPG) doesn't work.
This cha
media: qcom: camss: Fix csid-gen2 for test pattern generator
commit 87889f1b7ea40d2544b49c62092e6ef2792dced7 upstream.
In the current driver csid Test Pattern Generator (TPG) doesn't work.
This change:
- fixes writing frame width and height values into CSID_TPG_DT_n_CFG_0
- fixes the shift by one between test_pattern control value and the
actual pattern.
- drops fixed VC of 0x0a which testing showed prohibited some test
patterns in the CSID to produce output.
So that TPG starts working, but with the below limitations:
- only test_pattern=9 works as it should
- test_pattern=8 and test_pattern=7 produce black frame (all zeroes)
- the rest of test_pattern's don't work (yavta doesn't get the data)
- regardless of the CFA pattern set by 'media-ctl -V' the actual pixel
order is always the same (RGGB for any RAW8 or RAW10P format in
4608x2592 resolution).
Tested with:
RAW10P format, VC0:
media-ctl -V '"msm_csid0":0[fmt:SRGGB10/4608x2592 field:none]'
media-ctl -V '"msm_vfe0_rdi0":0[fmt:SRGGB10/4608x2592 field:none]'
media-ctl -l '"msm_csid0":1->"msm_vfe0_rdi0":0[1]'
v4l2-ctl -d /dev/v4l-subdev6 -c test_pattern=9
yavta -B capture-mplane --capture=3 -n 3 -f SRGGB10P -s 4608x2592 /dev/video0
RAW10P format, VC1:
media-ctl -V '"msm_csid0":2[fmt:SRGGB10/4608x2592 field:none]'
media-ctl -V '"msm_vfe0_rdi1":0[fmt:SRGGB10/4608x2592 field:none]'
media-ctl -l '"msm_csid0":2->"msm_vfe0_rdi1":0[1]'
v4l2-ctl -d /dev/v4l-subdev6 -c test_pattern=9
yavta -B capture-mplane --capture=3 -n 3 -f SRGGB10P -s 4608x2592 /dev/video1
RAW8 format, VC0:
media-ctl --reset
media-ctl -V '"msm_csid0":0[fmt:SRGGB8/4608x2592 field:none]'
media-ctl -V '"msm_vfe0_rdi0":0[fmt:SRGGB8/4608x2592 field:none]'
media-ctl -l '"msm_csid0":1->"msm_vfe0_rdi0":0[1]'
yavta -B capture-mplane --capture=3 -n 3 -f SRGGB8 -s 4608x2592 /dev/video0
Fixes: eebe6d00e9bf ("media: camss: Add support for CSID hardware version Titan 170")
Cc: stable@vger.kernel.org
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
show more ...
|
| e09e1ddc | 30-Aug-2023 |
Bryan O'Donoghue <bryan.odonoghue@linaro.org> |
media: qcom: camss: Fix invalid clock enable bit disjunction
commit d8f7e1a60d01739a1d78db2b08603089c6cf7c8e upstream.
define CSIPHY_3PH_CMN_CSI_COMMON_CTRL5_CLK_ENABLE BIT(7)
disjunction for gen2
media: qcom: camss: Fix invalid clock enable bit disjunction
commit d8f7e1a60d01739a1d78db2b08603089c6cf7c8e upstream.
define CSIPHY_3PH_CMN_CSI_COMMON_CTRL5_CLK_ENABLE BIT(7)
disjunction for gen2 ? BIT(7) : is a nop we are setting the same bit
either way.
Fixes: 4abb21309fda ("media: camss: csiphy: Move to hardcode CSI Clock Lane number")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
show more ...
|
| 5fbdccc9 | 30-Aug-2023 |
Bryan O'Donoghue <bryan.odonoghue@linaro.org> |
media: qcom: camss: Fix set CSI2_RX_CFG1_VC_MODE when VC is greater than 3
commit e655d1ae9703286cef7fda8675cad62f649dc183 upstream.
VC_MODE = 0 implies a two bit VC address.
VC_MODE = 1 is require
media: qcom: camss: Fix set CSI2_RX_CFG1_VC_MODE when VC is greater than 3
commit e655d1ae9703286cef7fda8675cad62f649dc183 upstream.
VC_MODE = 0 implies a two bit VC address.
VC_MODE = 1 is required for VCs with a larger address than two bits.
Fixes: eebe6d00e9bf ("media: camss: Add support for CSID hardware version Titan 170")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
show more ...
|
| f6cc8265 | 30-Aug-2023 |
Bryan O'Donoghue <bryan.odonoghue@linaro.org> |
media: qcom: camss: Fix missing vfe_lite clocks check
commit b6e1bdca463a932c1ac02caa7d3e14bf39288e0c upstream.
check_clock doesn't account for vfe_lite which means that vfe_lite will
never get val
media: qcom: camss: Fix missing vfe_lite clocks check
commit b6e1bdca463a932c1ac02caa7d3e14bf39288e0c upstream.
check_clock doesn't account for vfe_lite which means that vfe_lite will
never get validated by this routine. Add the clock name to the expected set
to remediate.
Fixes: 7319cdf189bb ("media: camss: Add support for VFE hardware version Titan 170")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
show more ...
|
| 4dac469b | 30-Aug-2023 |
Bryan O'Donoghue <bryan.odonoghue@linaro.org> |
media: qcom: camss: Fix VFE-480 vfe_disable_output()
commit 7f24d291350426d40b36dfbe6b3090617cdfd37a upstream.
vfe-480 is copied from vfe-17x and has the same racy idle timeout bug as in
17x.
Fix
media: qcom: camss: Fix VFE-480 vfe_disable_output()
commit 7f24d291350426d40b36dfbe6b3090617cdfd37a upstream.
vfe-480 is copied from vfe-17x and has the same racy idle timeout bug as in
17x.
Fix the vfe_disable_output() logic to no longer be racy and to conform
to the 17x way of quiescing and then resetting the VFE.
Fixes: 4edc8eae715c ("media: camss: Add initial support for VFE hardware version Titan 480")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
show more ...
|
| b1eaec00 | 30-Aug-2023 |
Bryan O'Donoghue <bryan.odonoghue@linaro.org> |
media: qcom: camss: Fix VFE-17x vfe_disable_output()
commit 3143ad282fc08bf995ee73e32a9e40c527bf265d upstream.
There are two problems with the current vfe_disable_output() routine.
Firstly we righ
media: qcom: camss: Fix VFE-17x vfe_disable_output()
commit 3143ad282fc08bf995ee73e32a9e40c527bf265d upstream.
There are two problems with the current vfe_disable_output() routine.
Firstly we rightly use a spinlock to protect output->gen2.active_num
everywhere except for in the IDLE timeout path of vfe_disable_output().
Even if that is not racy "in practice" somehow it is by happenstance not
by design.
Secondly we do not get consistent behaviour from this routine. On
sc8280xp 50% of the time I get "VFE idle timeout - resetting". In this
case the subsequent capture will succeed. The other 50% of the time, we
don't hit the idle timeout, never do the VFE reset and subsequent
captures stall indefinitely.
Rewrite the vfe_disable_output() routine to
- Quiesce write masters with vfe_wm_stop()
- Set active_num = 0
remembering to hold the spinlock when we do so followed by
- Reset the VFE
Testing on sc8280xp and sdm845 shows this to be a valid fix.
Fixes: 7319cdf189bb ("media: camss: Add support for VFE hardware version Titan 170")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
show more ...
|
| 816a4070 | 30-Aug-2023 |
Bryan O'Donoghue <bryan.odonoghue@linaro.org> |
media: qcom: camss: Fix vfe_get() error jump
commit 26bda3da00c3edef727a6acb00ed2eb4b22f8723 upstream.
Right now it is possible to do a vfe_get() with the internal reference
count at 1. If vfe_chec
media: qcom: camss: Fix vfe_get() error jump
commit 26bda3da00c3edef727a6acb00ed2eb4b22f8723 upstream.
Right now it is possible to do a vfe_get() with the internal reference
count at 1. If vfe_check_clock_rates() returns non-zero then we will
leave the reference count as-is and
run:
- pm_runtime_put_sync()
- vfe->ops->pm_domain_off()
skip:
- camss_disable_clocks()
Subsequent vfe_put() calls will when the ref-count is non-zero
unconditionally run:
- pm_runtime_put_sync()
- vfe->ops->pm_domain_off()
- camss_disable_clocks()
vfe_get() should not attempt to roll-back on error when the ref-count is
non-zero as the upper layers will still do their own vfe_put() operations.
vfe_put() will drop the reference count and do the necessary power
domain release, the cleanup jumps in vfe_get() should only be run when
the ref-count is zero.
[ 50.095796] CPU: 7 PID: 3075 Comm: cam Not tainted 6.3.2+ #80
[ 50.095798] Hardware name: LENOVO 21BXCTO1WW/21BXCTO1WW, BIOS N3HET82W (1.54 ) 05/26/2023
[ 50.095799] pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 50.095802] pc : refcount_warn_saturate+0xf4/0x148
[ 50.095804] lr : refcount_warn_saturate+0xf4/0x148
[ 50.095805] sp : ffff80000c7cb8b0
[ 50.095806] x29: ffff80000c7cb8b0 x28: ffff16ecc0e3fc10 x27: 0000000000000000
[ 50.095810] x26: 0000000000000000 x25: 0000000000020802 x24: 0000000000000000
[ 50.095813] x23: ffff16ecc7360640 x22: 00000000ffffffff x21: 0000000000000005
[ 50.095815] x20: ffff16ed175f4400 x19: ffffb4d9852942a8 x18: ffffffffffffffff
[ 50.095818] x17: ffffb4d9852d4a48 x16: ffffb4d983da5db8 x15: ffff80000c7cb320
[ 50.095821] x14: 0000000000000001 x13: 2e656572662d7265 x12: 7466612d65737520
[ 50.095823] x11: 00000000ffffefff x10: ffffb4d9850cebf0 x9 : ffffb4d9835cf954
[ 50.095826] x8 : 0000000000017fe8 x7 : c0000000ffffefff x6 : 0000000000057fa8
[ 50.095829] x5 : ffff16f813fe3d08 x4 : 0000000000000000 x3 : ffff621e8f4d2000
[ 50.095832] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff16ed32119040
[ 50.095835] Call trace:
[ 50.095836] refcount_warn_saturate+0xf4/0x148
[ 50.095838] device_link_put_kref+0x84/0xc8
[ 50.095843] device_link_del+0x38/0x58
[ 50.095846] vfe_pm_domain_off+0x3c/0x50 [qcom_camss]
[ 50.095860] vfe_put+0x114/0x140 [qcom_camss]
[ 50.095869] csid_set_power+0x2c8/0x408 [qcom_camss]
[ 50.095878] pipeline_pm_power_one+0x164/0x170 [videodev]
[ 50.095896] pipeline_pm_power+0xc4/0x110 [videodev]
[ 50.095909] v4l2_pipeline_pm_use+0x5c/0xa0 [videodev]
[ 50.095923] v4l2_pipeline_pm_get+0x1c/0x30 [videodev]
[ 50.095937] video_open+0x7c/0x100 [qcom_camss]
[ 50.095945] v4l2_open+0x84/0x130 [videodev]
[ 50.095960] chrdev_open+0xc8/0x250
[ 50.095964] do_dentry_open+0x1bc/0x498
[ 50.095966] vfs_open+0x34/0x40
[ 50.095968] path_openat+0xb44/0xf20
[ 50.095971] do_filp_open+0xa4/0x160
[ 50.095974] do_sys_openat2+0xc8/0x188
[ 50.095975] __arm64_sys_openat+0x6c/0xb8
[ 50.095977] invoke_syscall+0x50/0x128
[ 50.095982] el0_svc_common.constprop.0+0x4c/0x100
[ 50.095985] do_el0_svc+0x40/0xa8
[ 50.095988] el0_svc+0x2c/0x88
[ 50.095991] el0t_64_sync_handler+0xf4/0x120
[ 50.095994] el0t_64_sync+0x190/0x198
[ 50.095996] ---[ end trace 0000000000000000 ]---
Fixes: 779096916dae ("media: camss: vfe: Fix runtime PM imbalance on error")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
show more ...
|
| 89013969 | 09-Dec-2022 |
Milen Mitkov <quic_mmitkov@quicinc.com> |
media: camss: sm8250: Pipeline starting and stopping for multiple virtual channels
Use the multistream series function video_device_pipeline_alloc_start
to allows multiple clients of the same pipeli
media: camss: sm8250: Pipeline starting and stopping for multiple virtual channels
Use the multistream series function video_device_pipeline_alloc_start
to allows multiple clients of the same pipeline.
If the VFE entity is used by another instance of the pipeline,
the pipeline won't be stopped. This allows for stopping and starting
streams at any point without disrupting the other running streams.
To prepare and start multiple virtual channels each CSID source pad
corresponding to a virtual channel must be linked to the corresponding
IFE entity. CSID pad 1 (1st source pad) corresponds to virtual
channel 0, CSID pad 2 corresponds to virtual channel 1 and so on.
Each of these must be linked to corresponding IFE RDI port.
E.g. to enable vc 0 on CSID0:
media-ctl -l '"msm_csid0":1->"msm_vfe0_rdi0":0[1]'
To enable vc1 on CSID0:
media-ctl -l '"msm_csid0":2->"msm_vfe0_rdi1":0[1]'
And so on. Note that on SM8250 each CSID is connected, at the
hardware level, to only one IFE. Thus, you must link CSID0
with IFE0, you can't link it with IFE1.
Example: the following media controller setup expects multiplexed
sensor data on CSIPHY2. Data will be passed on to CSID0, which will
demux it to 2 streams - for RDI0 and RD1 ports of IFE0:
media-ctl -v -d /dev/media0 -V '"imx577 '22-001a'":0[fmt:SRGGB10/3840x2160 field:none]'
media-ctl -V '"msm_csiphy2":0[fmt:SRGGB10/3840x2160]'
media-ctl -V '"msm_csid0":0[fmt:SRGGB10/3840x2160]'
media-ctl -V '"msm_csid0":1[fmt:SRGGB10/3840x2160]'
media-ctl -V '"msm_csid0":2[fmt:SRGGB10/3840x2160]'
media-ctl -V '"msm_vfe0_rdi0":0[fmt:SRGGB10/3840x2160]'
media-ctl -V '"msm_vfe0_rdi1":0[fmt:SRGGB10/3840x2160]'
media-ctl -l '"msm_csiphy2":1->"msm_csid0":0[1]'
media-ctl -l '"msm_csid0":1->"msm_vfe0_rdi0":0[1]'
media-ctl -l '"msm_csid0":2->"msm_vfe0_rdi1":0[1]'
Note: CSID's entity pad 0 is a sink pad, pads 1..4 are source pads
To start streaming a v4l2 client must open the corresponding
/dev/videoN node. For example, with yavta:
yavta -B capture-mplane -c -I -n 5 -f SRGGB10P -s 3840x2160 -F /dev/video0
yavta -B capture-mplane -c -I -n 5 -f SRGGB10P -s 3840x2160 -F /dev/video1
Note that IFEs (vfe0, vfe1) on SM8250 have 3 RDI ports and a single
PIX port and IFELites (vfe2, vfe3) have 4 RDI ports and no PIX port.
Signed-off-by: Milen Mitkov <quic_mmitkov@quicinc.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
show more ...
|
| 1c4abf02 | 09-Dec-2022 |
Milen Mitkov <quic_mmitkov@quicinc.com> |
media: camss: vfe-480: Multiple outputs support for SM8250
On SM8250 each VFE supports at least 3 RDI channels, or 4
in case of VFE-Lite, so add appropriate IRQ setup and handling.
Signed-off-by: M
media: camss: vfe-480: Multiple outputs support for SM8250
On SM8250 each VFE supports at least 3 RDI channels, or 4
in case of VFE-Lite, so add appropriate IRQ setup and handling.
Signed-off-by: Milen Mitkov <quic_mmitkov@quicinc.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
show more ...
|
| 8ce158c1 | 09-Dec-2022 |
Milen Mitkov <quic_mmitkov@quicinc.com> |
media: camss: vfe: Reserve VFE lines on stream start and link to CSID
For multiple virtual channels support, each VFE line can be in either
ON, RESERVED or OFF states. This allows the starting and s
media: camss: vfe: Reserve VFE lines on stream start and link to CSID
For multiple virtual channels support, each VFE line can be in either
ON, RESERVED or OFF states. This allows the starting and stopping
of a VFE line independently of other active VFE lines (e.g. already-
running lines stay in ON state, and newly-added lines are RESERVED)
Also, link the CSID entity's source ports to corresponding VFE lines.
Signed-off-by: Milen Mitkov <quic_mmitkov@quicinc.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
show more ...
|