Merge tag 'v6.6.57' into for/openbmc/dev-6.6

This is the 6.6.57 stable release

ata: ahci: Add mask_port_map module parameter

[ Upstream commit 24cfd86433c920188ac3f02df8aba6bc4c792f4b ]

Commits 0077a504e1a4 ("ahci: asm1166: correct count of reported ports")
and 9815e3961754 (

ata: ahci: Add mask_port_map module parameter

[ Upstream commit 24cfd86433c920188ac3f02df8aba6bc4c792f4b ]

Commits 0077a504e1a4 ("ahci: asm1166: correct count of reported ports")
and 9815e3961754 ("ahci: asm1064: correct count of reported ports")
attempted to limit the ports of the ASM1166 and ASM1064 AHCI controllers
to avoid long boot times caused by the fact that these adapters report
a port map larger than the number of physical ports. The excess ports
are "virtual" to hide port multiplier devices and probing these ports
takes time. However, these commits caused a regression for users that do
use PMP devices, as the ATA devices connected to the PMP cannot be
scanned. These commits have thus been reverted by commit 6cd8adc3e18
("ahci: asm1064: asm1166: don't limit reported ports") to allow the
discovery of devices connected through a port multiplier. But this
revert re-introduced the long boot times for users that do not use a
port multiplier setup.

This patch adds the mask_port_map ahci module parameter to allow users
to manually specify port map masks for controllers. In the case of the
ASMedia 1166 and 1064 controllers, users that do not have port
multiplier devices can mask the excess virtual ports exposed by the
controller to speedup port scanning, thus reducing boot time.

The mask_port_map parameter accepts 2 different formats:
- mask_port_map=<mask>
This applies the same mask to all AHCI controllers
present in the system. This format is convenient for small systems
that have only a single AHCI controller.
- mask_port_map=<pci_dev>=<mask>,<pci_dev>=mask,...
This applies the specified masks only to the PCI device listed. The
<pci_dev> field is a regular PCI device ID (domain:bus:dev.func).
This ID can be seen following "ahci" in the kernel messages. E.g.
for "ahci 0000:01:00.0: 2/2 ports implemented (port mask 0x3)", the
<pci_dev> field is "0000:01:00.0".

When used, the function ahci_save_initial_config() indicates that a
port map mask was applied with the message "masking port_map ...".
E.g.: without a mask:
modprobe ahci
dmesg | grep ahci
...
ahci 0000:00:17.0: AHCI vers 0001.0301, 32 command slots, 6 Gbps, SATA mode
ahci 0000:00:17.0: (0000:00:17.0) 8/8 ports implemented (port mask 0xff)

With a mask:
modprobe ahci mask_port_map=0000:00:17.0=0x1
dmesg | grep ahci
...
ahci 0000:00:17.0: masking port_map 0xff -> 0x1
ahci 0000:00:17.0: AHCI vers 0001.0301, 32 command slots, 6 Gbps, SATA mode
ahci 0000:00:17.0: (0000:00:17.0) 1/8 ports implemented (port mask 0x1)

Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

Merge tag 'v6.6.37' into dev-6.6

This is the 6.6.37 stable release

ata: ahci: Clean up sysfs file on error

commit eeb25a09c5e0805d92e4ebd12c4b0ad0df1b0295 upstream.

.probe() (ahci_init_one()) calls sysfs_add_file_to_group(), however,
if probe() fails after this ca

ata: ahci: Clean up sysfs file on error

commit eeb25a09c5e0805d92e4ebd12c4b0ad0df1b0295 upstream.

.probe() (ahci_init_one()) calls sysfs_add_file_to_group(), however,
if probe() fails after this call, we currently never call
sysfs_remove_file_from_group().

(The sysfs_remove_file_from_group() call in .remove() (ahci_remove_one())
does not help, as .remove() is not called on .probe() error.)

Thus, if probe() fails after the sysfs_add_file_to_group() call, the next
time we insmod the module we will get:

sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:04.0/remapped_nvme'
CPU: 11 PID: 954 Comm: modprobe Not tainted 6.10.0-rc5 #43
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-2.fc40 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x5d/0x80
sysfs_warn_dup.cold+0x17/0x23
sysfs_add_file_mode_ns+0x11a/0x130
sysfs_add_file_to_group+0x7e/0xc0
ahci_init_one+0x31f/0xd40 [ahci]

Fixes: 894fba7f434a ("ata: ahci: Add sysfs attribute to show remapped NVMe device count")
Cc: stable@vger.kernel.org
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240629124210.181537-10-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

Merge tag 'v6.6.24' into dev-6.6

This is the 6.6.24 stable release

ahci: asm1064: asm1166: don't limit reported ports

[ Upstream commit 6cd8adc3e18960f6e59d797285ed34ef473cc896 ]

Previously, patches have been added to limit the reported count of SATA
ports for asm

ahci: asm1064: asm1166: don't limit reported ports

[ Upstream commit 6cd8adc3e18960f6e59d797285ed34ef473cc896 ]

Previously, patches have been added to limit the reported count of SATA
ports for asm1064 and asm1166 SATA controllers, as those controllers do
report more ports than physically having.

While it is allowed to report more ports than physically having in CAP.NP,
it is not allowed to report more ports than physically having in the PI
(Ports Implemented) register, which is what these HBAs do.
(This is a AHCI spec violation.)

Unfortunately, it seems that the PMP implementation in these ASMedia HBAs
is also violating the AHCI and SATA-IO PMP specification.

What these HBAs do is that they do not report that they support PMP
(CAP.SPM (Supports Port Multiplier) is not set).

Instead, they have decided to add extra "virtual" ports in the PI register
that is used if a port multiplier is connected to any of the physical
ports of the HBA.

Enumerating the devices behind the PMP as specified in the AHCI and
SATA-IO specifications, by using PMP READ and PMP WRITE commands to the
physical ports of the HBA is not possible, you have to use the "virtual"
ports.

This is of course bad, because this gives us no way to detect the device
and vendor ID of the PMP actually connected to the HBA, which means that
we can not apply the proper PMP quirks for the PMP that is connected to
the HBA.

Limiting the port map will thus stop these controllers from working with
SATA Port Multipliers.

This patch reverts both patches for asm1064 and asm1166, so old behavior
is restored and SATA PMP will work again, but it will also reintroduce the
(minutes long) extra boot time for the ASMedia controllers that do not
have a PMP connected (either on the PCIe card itself, or an external PMP).

However, a longer boot time for some, is the lesser evil compared to some
other users not being able to detect their drives at all.

Fixes: 0077a504e1a4 ("ahci: asm1166: correct count of reported ports")
Fixes: 9815e3961754 ("ahci: asm1064: correct count of reported ports")
Cc: stable@vger.kernel.org
Reported-by: Matt <cryptearth@googlemail.com>
Signed-off-by: Conrad Kostecki <conikost@gentoo.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
[cassel: rewrote commit message]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

ahci: asm1064: correct count of reported ports

[ Upstream commit 9815e39617541ef52d0dfac4be274ad378c6dc09 ]

The ASM1064 SATA host controller always reports wrongly,
that it has 24 ports. But in rea

ahci: asm1064: correct count of reported ports

[ Upstream commit 9815e39617541ef52d0dfac4be274ad378c6dc09 ]

The ASM1064 SATA host controller always reports wrongly,
that it has 24 ports. But in reality, it only has four ports.

before:
ahci 0000:04:00.0: SSS flag set, parallel bus scan disabled
ahci 0000:04:00.0: AHCI 0001.0301 32 slots 24 ports 6 Gbps 0xffff0f impl SATA mode
ahci 0000:04:00.0: flags: 64bit ncq sntf stag pm led only pio sxs deso sadm sds apst

after:
ahci 0000:04:00.0: ASM1064 has only four ports
ahci 0000:04:00.0: forcing port_map 0xffff0f -> 0xf
ahci 0000:04:00.0: SSS flag set, parallel bus scan disabled
ahci 0000:04:00.0: AHCI 0001.0301 32 slots 24 ports 6 Gbps 0xf impl SATA mode
ahci 0000:04:00.0: flags: 64bit ncq sntf stag pm led only pio sxs deso sadm sds apst

Signed-off-by: "Andrey Jr. Melnikov" <temnota.am@gmail.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Stable-dep-of: 6cd8adc3e189 ("ahci: asm1064: asm1166: don't limit reported ports")
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

Merge tag 'v6.6.19' into dev-6.6

This is the 6.6.19 stable release

ahci: Extend ASM1061 43-bit DMA address quirk to other ASM106x parts

commit 51af8f255bdaca6d501afc0d085b808f67b44d91 upstream.

ASMedia have confirmed that all ASM106x parts currently listed in
ahci

ahci: Extend ASM1061 43-bit DMA address quirk to other ASM106x parts

commit 51af8f255bdaca6d501afc0d085b808f67b44d91 upstream.

ASMedia have confirmed that all ASM106x parts currently listed in
ahci_pci_tbl[] suffer from the 43-bit DMA address limitation that we ran
into on the ASM1061, and therefore, we need to apply the quirk added by
commit 20730e9b2778 ("ahci: add 43-bit DMA address quirk for ASMedia
ASM1061 controllers") to the other supported ASM106x parts as well.

Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-ide/ZbopwKZJAKQRA4Xv@x1-carbon/
Signed-off-by: Lennert Buytenhek <kernel@wantstofly.org>
[cassel: add link to ASMedia confirmation email]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

ata: ahci: add identifiers for ASM2116 series adapters

commit 3bf6141060948e27b62b13beb216887f2e54591e upstream.

Add support for PCIe SATA adapter cards based on Asmedia 2116 controllers.
These car

ata: ahci: add identifiers for ASM2116 series adapters

commit 3bf6141060948e27b62b13beb216887f2e54591e upstream.

Add support for PCIe SATA adapter cards based on Asmedia 2116 controllers.
These cards can provide up to 10 SATA ports on PCIe card.

Signed-off-by: Szuying Chen <Chloe_Chen@asmedia.com.tw>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

ahci: add 43-bit DMA address quirk for ASMedia ASM1061 controllers

[ Upstream commit 20730e9b277873deeb6637339edcba64468f3da3 ]

With one of the on-board ASM1061 AHCI controllers (1b21:0612) on an
A

ahci: add 43-bit DMA address quirk for ASMedia ASM1061 controllers

[ Upstream commit 20730e9b277873deeb6637339edcba64468f3da3 ]

With one of the on-board ASM1061 AHCI controllers (1b21:0612) on an
ASUSTeK Pro WS WRX80E-SAGE SE WIFI mainboard, a controller hang was
observed that was immediately preceded by the following kernel
messages:

ahci 0000:28:00.0: Using 64-bit DMA addresses
ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00000 flags=0x0000]
ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00300 flags=0x0000]
ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00380 flags=0x0000]
ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00400 flags=0x0000]
ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00680 flags=0x0000]
ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00700 flags=0x0000]

The first message is produced by code in drivers/iommu/dma-iommu.c
which is accompanied by the following comment that seems to apply:

/*
* Try to use all the 32-bit PCI addresses first. The original SAC vs.
* DAC reasoning loses relevance with PCIe, but enough hardware and
* firmware bugs are still lurking out there that it's safest not to
* venture into the 64-bit space until necessary.
*
* If your device goes wrong after seeing the notice then likely either
* its driver is not setting DMA masks accurately, the hardware has
* some inherent bug in handling >32-bit addresses, or not all the
* expected address bits are wired up between the device and the IOMMU.
*/

Asking the ASM1061 on a discrete PCIe card to DMA from I/O virtual
address 0xffffffff00000000 produces the following I/O page faults:

vfio-pci 0000:07:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0021 address=0x7ff00000000 flags=0x0010]
vfio-pci 0000:07:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0021 address=0x7ff00000500 flags=0x0010]

Note that the upper 21 bits of the logged DMA address are zero. (When
asking a different PCIe device in the same PCIe slot to DMA to the
same I/O virtual address, we do see all the upper 32 bits of the DMA
address as 1, so this is not an issue with the chipset or IOMMU
configuration on the test system.)

Also, hacking libahci to always set the upper 21 bits of all DMA
addresses to 1 produces no discernible effect on the behavior of the
ASM1061, and mkfs/mount/scrub/etc work as without this hack.

This all strongly suggests that the ASM1061 has a 43 bit DMA address
limit, and this commit therefore adds a quirk to deal with this limit.

This issue probably applies to (some of) the other supported ASMedia
parts as well, but we limit it to the PCI IDs known to refer to
ASM1061 parts, as that's the only part we know for sure to be affected
by this issue at this point.

Link: https://lore.kernel.org/linux-ide/ZaZ2PIpEId-rl6jv@wantstofly.org/
Signed-off-by: Lennert Buytenhek <kernel@wantstofly.org>
[cassel: drop date from error messages in commit log]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

ahci: asm1166: correct count of reported ports

[ Upstream commit 0077a504e1a4468669fd2e011108db49133db56e ]

The ASM1166 SATA host controller always reports wrongly,
that it has 32 ports. But in rea

ahci: asm1166: correct count of reported ports

[ Upstream commit 0077a504e1a4468669fd2e011108db49133db56e ]

The ASM1166 SATA host controller always reports wrongly,
that it has 32 ports. But in reality, it only has six ports.

This seems to be a hardware issue, as all tested ASM1166
SATA host controllers reports such high count of ports.

Example output: ahci 0000:09:00.0: AHCI 0001.0301
32 slots 32 ports 6 Gbps 0xffffff3f impl SATA mode.

By adjusting the port_map, the count is limited to six ports.

New output: ahci 0000:09:00.0: AHCI 0001.0301
32 slots 32 ports 6 Gbps 0x3f impl SATA mode.

Closes: https://bugzilla.kernel.org/show_bug.cgi?id=211873
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218346
Signed-off-by: Conrad Kostecki <conikost@gentoo.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

Merge tag 'kvm-riscv-fixes-6.6-1' of https://github.com/kvm-riscv/linux into HEAD

KVM/riscv fixes for 6.6, take #1

- Fix KVM_GET_REG_LIST API for ISA_EXT registers
- Fix reading ISA_EXT register of

Merge tag 'kvm-riscv-fixes-6.6-1' of https://github.com/kvm-riscv/linux into HEAD

KVM/riscv fixes for 6.6, take #1

- Fix KVM_GET_REG_LIST API for ISA_EXT registers
- Fix reading ISA_EXT register of a missing extension
- Fix ISA_EXT register handling in get-reg-list test
- Fix filtering of AIA registers in get-reg-list test

show more ...

Merge tag 'ata-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata

Pull ata fixes from Damien Le Moal:

- Fix link power management transitions to disallow unsupported states

Merge tag 'ata-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata

Pull ata fixes from Damien Le Moal:

- Fix link power management transitions to disallow unsupported states
(Niklas)

- A small string handling fix for the sata_mv driver (Christophe)

- Clear port pending interrupts before reset, as per AHCI
specifications (Szuying).

Followup fixes for this one are to not clear ATA_PFLAG_EH_PENDING in
ata_eh_reset() to allow EH to continue on with other actions recorded
with error interrupts triggered before EH completes. And an
additional fix to avoid thawing a port twice in EH (Niklas)

- Small code style fixes in the pata_parport driver to silence the
build bot as it keeps complaining about bad indentation (me)

- A fix for the recent CDL code to avoid fetching sense data for
successful commands when not necessary for correct operation (Niklas)

* tag 'ata-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: libata-core: fetch sense data for successful commands iff CDL enabled
ata: libata-eh: do not thaw the port twice in ata_eh_reset()
ata: libata-eh: do not clear ATA_PFLAG_EH_PENDING in ata_eh_reset()
ata: pata_parport: Fix code style issues
ata: libahci: clear pending interrupt status
ata: sata_mv: Fix incorrect string length computation in mv_dump_mem()
ata: libata: disallow dev-initiated LPM transitions to unsupported states

show more ...

Merge drm/drm-fixes into drm-misc-fixes

Forwarding to v6.6-rc1.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>

ata: libata: disallow dev-initiated LPM transitions to unsupported states

In AHCI 1.3.1, the register description for CAP.SSC:
"When cleared to ‘0’, software must not allow the HBA to initiate
trans

ata: libata: disallow dev-initiated LPM transitions to unsupported states

In AHCI 1.3.1, the register description for CAP.SSC:
"When cleared to ‘0’, software must not allow the HBA to initiate
transitions to the Slumber state via agressive link power management nor
the PxCMD.ICC field in each port, and the PxSCTL.IPM field in each port
must be programmed to disallow device initiated Slumber requests."

In AHCI 1.3.1, the register description for CAP.PSC:
"When cleared to ‘0’, software must not allow the HBA to initiate
transitions to the Partial state via agressive link power management nor
the PxCMD.ICC field in each port, and the PxSCTL.IPM field in each port
must be programmed to disallow device initiated Partial requests."

Ensure that we always set the corresponding bits in PxSCTL.IPM, such that
a device is not allowed to initiate transitions to power states which are
unsupported by the HBA.

DevSleep is always initiated by the HBA, however, for completeness, set the
corresponding bit in PxSCTL.IPM such that agressive link power management
cannot transition to DevSleep if DevSleep is not supported.

sata_link_scr_lpm() is used by libahci, ata_piix and libata-pmp.
However, only libahci has the ability to read the CAP/CAP2 register to see
if these features are supported. Therefore, in order to not introduce any
regressions on ata_piix or libata-pmp, create flags that indicate that the
respective feature is NOT supported. This way, the behavior for ata_piix
and libata-pmp should remain unchanged.

This change is based on a patch originally submitted by Runa Guo-oc.

Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Fixes: 1152b2617a6e ("libata: implement sata_link_scr_lpm() and make ata_dev_set_feature() global")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>

show more ...

Merge tag 'ata-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata

Pull ata updates from Damien Le Moal:

- Fix OF include file for ata platform drivers (Rob)

- Simplify vari

Merge tag 'ata-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata

Pull ata updates from Damien Le Moal:

- Fix OF include file for ata platform drivers (Rob)

- Simplify various ahci, sata and pata platform drivers using the
function devm_platform_ioremap_resource() (Yangtao)

- Cleanup libata time related argument types (e.g. timeouts values)
(Sergey)

- Cleanup libata code around error handling as all ata drivers now
define a error_handler operation (Hannes and Niklas)

- Remove functions intended for libsas that are in fact unused (Niklas)

- Change the remove device callback of platform drivers to a null
function (Uwe)

- Simplify the pata_imx driver using devm_clk_get_enabled() (Li)

- Remove old and uinused remnants of the ide code in arm, parisc,
powerpc, sparc and m68k architectures and associated drivers
(pata_buddha, pata_falcon and pata_gayle) (Geert)

- Add missing MODULE_DESCRIPTION() in the sata_gemini and pata_ftide010
drivers (me)

- Several fixes for the pata_ep93xx and pata_falcon drivers (Nikita,
Michael)

- Add Elkhart Lake AHCI controller support to the ahci driver (Werner)

- Disable NCQ trim on Micron 1100 drives (Pawel)

* tag 'ata-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata: (60 commits)
ata: libata-core: Disable NCQ_TRIM on Micron 1100 drives
ata: ahci: Add Elkhart Lake AHCI controller
ata: pata_falcon: add data_swab option to byte-swap disk data
ata: pata_falcon: fix IO base selection for Q40
ata: pata_ep93xx: use soc_device_match for UDMA modes
ata: pata_ep93xx: fix error return code in probe
ata: sata_gemini: Add missing MODULE_DESCRIPTION
ata: pata_ftide010: Add missing MODULE_DESCRIPTION
m68k: Remove <asm/ide.h>
ata: pata_gayle: Remove #include <asm/ide.h>
ata: pata_falcon: Remove #include <asm/ide.h>
ata: pata_buddha: Remove #include <asm/ide.h>
asm-generic: Remove ide_iops.h
sparc: Remove <asm/ide.h>
powerpc: Remove <asm/ide.h>
parisc: Remove <asm/ide.h>
ARM: Remove <asm/ide.h>
ata: pata_imx: Use helper function devm_clk_get_enabled()
ata: sata_rcar: Convert to platform remove callback returning void
ata: sata_mv: Convert to platform remove callback returning void
...

show more ...

ata: ahci: Add Elkhart Lake AHCI controller

Elkhart Lake is the successor of Apollo Lake and Gemini Lake. These
CPUs and their PCHs are used in mobile and embedded environments.

With this patch I s

ata: ahci: Add Elkhart Lake AHCI controller

Elkhart Lake is the successor of Apollo Lake and Gemini Lake. These
CPUs and their PCHs are used in mobile and embedded environments.

With this patch I suggest that Elkhart Lake SATA controllers [1] should
use the default LPM policy for mobile chipsets.
The disadvantage of missing hot-plug support with this setting should
not be an issue, as those CPUs are used in embedded environments and
not in servers with hot-plug backplanes.

We discovered that the Elkhart Lake SATA controllers have been missing
in ahci.c after a customer reported the throttling of his SATA SSD
after a short period of higher I/O. We determined the high temperature
of the SSD controller in idle mode as the root cause for that.

Depending on the used SSD, we have seen up to 1.8 Watt lower system
idle power usage and up to 30°C lower SSD controller temperatures in
our tests, when we set med_power_with_dipm manually. I have provided a
table showing seven different SATA SSDs from ATP, Intel/Solidigm and
Samsung [2].

Intel lists a total of 3 SATA controller IDs (4B60, 4B62, 4B63) in [1]
for those mobile PCHs.
This commit just adds 0x4b63 as I do not have test systems with 0x4b60
and 0x4b62 SATA controllers.
I have tested this patch with a system which uses 0x4b63 as SATA
controller.

[1] https://sata-io.org/product/8803
[2] https://www.thomas-krenn.com/en/wiki/SATA_Link_Power_Management#Example_LES_v4

Signed-off-by: Werner Fischer <devlists@wefi.net>
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>

show more ...

Merge branch 'next' into for-linus

Prepare input updates for 6.6 merge window.

ata: fix debounce timings type

sata_deb_timing_{hotplug|long|normal}[] store 'unsigned long' debounce
timeouts in ms, while sata_link_debounce() eventually uses those timeouts
by calling ata_{deadli

ata: fix debounce timings type

sata_deb_timing_{hotplug|long|normal}[] store 'unsigned long' debounce
timeouts in ms, while sata_link_debounce() eventually uses those timeouts
by calling ata_{deadline|msleep}( which take just 'unsigned int'. Change
the debounce timeout table element's type to 'unsigned int' -- all these
timeouts happily fit into 'unsigned int'...

Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>

show more ...

Merge tag 'v6.4' into next

Sync up with mainline to bring in updates to shared infrastructure.

Merge drm/drm-next into drm-misc-next-fixes

Backmerging to sync drm-misc-next-fixes with drm-misc-next.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>

Merge branch 'drm-next' of git://anongit.freedesktop.org/drm/drm into msm-next-lumag-base

Merge the drm-next tree to pick up the DRM DSC helpers (merged via
drm-intel-next tree). MSM DSC v1.2 patche

Merge branch 'drm-next' of git://anongit.freedesktop.org/drm/drm into msm-next-lumag-base

Merge the drm-next tree to pick up the DRM DSC helpers (merged via
drm-intel-next tree). MSM DSC v1.2 patches depend on these helpers.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

show more ...

Merge tag 'v6.4-rc4' into wpan-next/staging

Linux 6.4-rc4

Merge drm/drm-next into drm-intel-gt-next

For conflict avoidance we need the following commit:

c9a9f18d3ad8 drm/i915/huc: use const struct bus_type pointers

Signed-off-by: Tvrtko Ursulin <tvrtko

Merge drm/drm-next into drm-intel-gt-next

For conflict avoidance we need the following commit:

c9a9f18d3ad8 drm/i915/huc: use const struct bus_type pointers

Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

show more ...