| /openbmc/openbmc/meta-openembedded/meta-oe/recipes-extended/mozjs/mozjs-115/ |
| H A D | armv5.patch | 15 // reloaded from the icache.
|
| /openbmc/u-boot/doc/ |
| H A D | README.fsl_iim | 37 this operation, the shadow registers are reloaded by the hardware (not
|
| H A D | README.mxc_ocotp | 41 Following this operation, the shadow registers are not reloaded by the
|
| /openbmc/linux/Documentation/ABI/testing/ |
| H A D | sysfs-class-ocxl | 44 Control whether the FPGA is reloaded on a link reset. Enabled
|
| H A D | sysfs-bus-counter | 112 counter is reloaded to the preset value, and the process
121 counter is reloaded to the preset value. The process
128 counter is reloaded to the preset value minus one.
131 counter is reloaded to the preset value minus one. The
|
| H A D | sysfs-class-cxl | 247 Trust that when an image is reloaded via PERST, it will not
|
| H A D | sysfs-bus-pci | 86 must be reloaded for the new setting to take effect.
|
| /openbmc/linux/arch/sh/kernel/ |
| H A D | entry-common.S | 377 ! below, so don't need to be reloaded here.)
|
| /openbmc/linux/Documentation/hwmon/ |
| H A D | nzxt-smart2.rst | 30 must be reloaded to detect configuration changes; otherwise, new fans can't
|
| /openbmc/linux/Documentation/w1/masters/ |
| H A D | ds2490.rst | 62 the ds2490 hardware, but if the module was unloaded, then reloaded
|
| /openbmc/linux/drivers/net/wireless/realtek/rtw89/ |
| H A D | rtw8852a_rfk.c | 2595 bool is_fail = true, reloaded[RTW8852A_DPK_RF_PATH] = {false}; in _dpk_cal_select() local
2602 reloaded[path] = _dpk_reload_check(rtwdev, phy, path); in _dpk_cal_select()
2603 if (!reloaded[path] && dpk->bp[path][0].ch != 0) in _dpk_cal_select()
2613 if ((kpath == RF_A && reloaded[RF_PATH_A]) || in _dpk_cal_select()
2614 (kpath == RF_B && reloaded[RF_PATH_B]) || in _dpk_cal_select()
2615 (kpath == RF_AB && reloaded[RF_PATH_A] && reloaded[RF_PATH_B])) in _dpk_cal_select()
2621 if (!(kpath & BIT(path)) || reloaded[path]) in _dpk_cal_select()
2633 if (!(kpath & BIT(path)) || reloaded[path]) in _dpk_cal_select()
2644 if (!(kpath & BIT(path)) || reloaded[path]) in _dpk_cal_select()
|
| H A D | rtw8852c_rfk.c | 2698 bool is_fail = true, reloaded[RTW8852C_DPK_RF_PATH] = {false}; in _dpk_cal_select() local
2707 reloaded[path] = _dpk_reload_check(rtwdev, phy, path); in _dpk_cal_select()
2708 if (!reloaded[path] && dpk->bp[path][0].ch != 0) in _dpk_cal_select()
|
| H A D | rtw8852b_rfk.c | 2500 bool is_fail = true, reloaded[RTW8852B_DPK_RF_PATH] = {}; in _dpk_cal_select() local
2505 reloaded[path] = _dpk_reload_check(rtwdev, phy, path); in _dpk_cal_select()
2506 if (!reloaded[path] && dpk->bp[path][0].ch) in _dpk_cal_select()
|
| /openbmc/linux/Documentation/networking/dsa/ |
| H A D | bcm_sf2.rst | 86 firmware gets reloaded. The SF2 driver relies on such events to properly set its
|
| /openbmc/linux/Documentation/virt/kvm/x86/ |
| H A D | timekeeping.rst | 98 is reloaded and the countdown automatically resumes. If the gate line goes
106 automatically reloaded on reaching zero. The count is decremented twice at
117 goes low for 1 clock cycle and returns high. The counter is not reloaded.
125 not reloaded.
|
| /openbmc/linux/arch/arm/kernel/ |
| H A D | entry-header.S | 88 @ reloaded.
|
| /openbmc/qemu/docs/system/ |
| H A D | authz.rst | 131 that can be reloaded automatically upon change.
|
| /openbmc/linux/Documentation/hid/ |
| H A D | uhid.rst | 149 reloaded/changed the device driver loaded on your HID device (or some other
|
| /openbmc/linux/drivers/staging/pi433/Documentation/ |
| H A D | pi433.txt | 35 started. Upon hardware fifo threshold interrupt it gets reloaded, thus enabling
|
| /openbmc/linux/Documentation/networking/device_drivers/ethernet/netronome/ |
| H A D | nfp.rst | 93 later reloaded manually everything works correctly.
|
| /openbmc/linux/Documentation/fb/ |
| H A D | fbcon.rst | 253 can be unloaded or reloaded at will. Reloading the drivers or fbcon will
|
| /openbmc/linux/kernel/power/ |
| H A D | Kconfig | 67 be reloaded, then use the 'noresume' kernel command line argument.
|
| /openbmc/linux/Documentation/networking/device_drivers/ethernet/intel/ |
| H A D | iavf.rst | 281 address may change each time the VF driver is reloaded. You can assign a static
|
| /openbmc/linux/Documentation/admin-guide/device-mapper/ |
| H A D | dm-integrity.rst | 214 data depend on them and the reloaded target would be non-functional.
|
| /openbmc/linux/Documentation/arch/arm/stm32/ |
| H A D | stm32-dma-mdma-chaining.rst | 52 counter is automatically reloaded. This allows the SW or the STM32 MDMA to
|