| /openbmc/linux/Documentation/devicetree/bindings/misc/ |
| H A D | xlnx,sd-fec.txt | 29 configures the DIN_WORDS to be block based, while a value of 2 configures the
32 configures a width of "1x128b", 2 a width of "2x128b" and 4 configures a width
36 configures the DOUT_WORDS to be block based, while a value of 2 configures the
39 configures a width of "1x128b", 2 a width of "2x128b" and 4 configures a width
|
| /openbmc/linux/Documentation/userspace-api/media/drivers/ |
| H A D | max2175.rst | 52 - This configures FM band with a sample rate of 0.512 million
55 - This configures VHF band with a sample rate of 2.048 million
60 - This configures FM band with a sample rate of 0.7441875 million
63 - This configures FM band with a sample rate of 0.372 million
|
| /openbmc/linux/drivers/thermal/mediatek/ |
| H A D | Kconfig | 18 This driver configures thermal controllers to collect
27 This driver configures LVTS (Low Voltage Thermal Sensor)
|
| /openbmc/linux/Documentation/devicetree/bindings/mmc/ |
| H A D | socionext,uniphier-sd.yaml | 62 - description: phandle to syscon that configures UHS mode
65 A phandle to syscon with one argument that configures UHS mode.
|
| /openbmc/linux/Documentation/devicetree/bindings/net/ |
| H A D | socionext,uniphier-ave4.yaml | 56 - description: phandle to syscon that configures phy mode
59 A phandle to syscon with one argument that configures phy mode.
|
| /openbmc/linux/Documentation/devicetree/bindings/pinctrl/ |
| H A D | fsl,imx27-pinctrl.txt | 32 gpio_oconf configures the gpio submodule output signal. This does not
43 gpio_iconfa/b configures the gpio submodule input to functionblocks A and
|
| H A D | nuvoton,wpcm450-pinctrl.yaml | 28 # 2. a pinmux node configures pin muxing for a group of pins (e.g. rmii2)
29 # 3. a pinconf node configures properties of a single pin
|
| /openbmc/openbmc/poky/meta/recipes-extended/parted/files/ |
| H A D | autoconf-2.73.patch | 17 # or configures them incorrectly in some cases.
|
| /openbmc/linux/Documentation/ABI/testing/ |
| H A D | sysfs-bus-iio-filter-admv8818 | 17 This attribute configures the filter mode.
|
| /openbmc/openbmc-test-automation/systest/ |
| H A D | test_boot_acceptance.robot | 29 # Script that configures every network port when connected to a loop. This
38 # This configures the cron to reboot the system and re-run the HTX profile.
|
| /openbmc/linux/Documentation/devicetree/bindings/usb/ |
| H A D | maxim,max3421.txt | 11 The driver configures MAX3421E for active low level triggered interrupts,
|
| /openbmc/openbmc/poky/meta/recipes-extended/gperf/ |
| H A D | gperf_3.1.bb | 17 # The nested configures don't find the parent aclocal.m4 out of the box, so tell
|
| /openbmc/openbmc/poky/meta/recipes-devtools/bison/bison/ |
| H A D | autoconf-2.73.patch | 19 # or configures them incorrectly in some cases.
|
| /openbmc/linux/Documentation/devicetree/bindings/display/ |
| H A D | intel,keembay-msscam.yaml | 15 MIPI DSI clocks. It also configures the interconnect between LCD and
|
| /openbmc/linux/Documentation/devicetree/bindings/net/can/ |
| H A D | ti_hecc.txt | 16 - ti,use-hecc1int: if provided configures HECC to produce all interrupts
|
| /openbmc/linux/Documentation/devicetree/bindings/hwmon/ |
| H A D | lm87.txt | 10 - has-temp3: This configures pins 18 and 19 to be used as a second
|
| /openbmc/linux/Documentation/devicetree/bindings/arm/hisilicon/controller/ |
| H A D | hi3798cv200-perictrl.yaml | 14 their status, and configures some functions of peripherals.
|
| /openbmc/linux/Documentation/devicetree/bindings/memory-controllers/ |
| H A D | canaan,k210-sram.yaml | 11 of SRAM. The controller is initialised by the bootloader, which configures
|
| /openbmc/linux/drivers/clk/xilinx/ |
| H A D | Kconfig | 10 register set. This driver also configures the frequency based on the
|
| /openbmc/linux/Documentation/devicetree/bindings/gpio/ |
| H A D | xlnx,gpio-xilinx.yaml | 109 description: This value configures the input or output mode
114 description: This value configures the input or output mode
|
| H A D | gpio-mm-lantiq.txt | 4 only gpios. This driver configures a special memory address, which when
|
| /openbmc/linux/Documentation/devicetree/bindings/sound/ |
| H A D | davinci-mcasp-audio.yaml | 82 configures WFIFO threshold
89 configures RFIFO threshold
|
| /openbmc/linux/arch/arm/boot/dts/marvell/ |
| H A D | armada-388-clearfog-base.dts | 49 * Annoyingly, the marvell phy driver configures the LED
|
| /openbmc/u-boot/board/toradex/apalis_imx6/ |
| H A D | Kconfig | 48 This option configures DCE mode unconditionally. Whithout this
|
| /openbmc/linux/Documentation/devicetree/bindings/clock/ |
| H A D | qcom,spmi-clkdiv.yaml | 14 Qualcomm SPMI PMIC clock divider configures the clock frequency of a set of
|