/openbmc/linux/drivers/usb/host/ |
H A D | ehci-hub.c | 27 udev->bus->root_hub->speed < USB_SPEED_HIGH; in persist_enabled_on_companion()
|
H A D | ehci-sched.c | 1041 if (dev->speed == USB_SPEED_HIGH) { in iso_stream_init() 1085 dev->speed, is_input, 1, maxp)); in iso_stream_init()
|
/openbmc/linux/drivers/net/hyperv/ |
H A D | hyperv_net.h | 1045 u32 speed; member
|
/openbmc/linux/drivers/media/usb/go7007/ |
H A D | go7007-usb.c | 1266 usbdev->speed != USB_SPEED_HIGH) in go7007_usb_probe()
|
/openbmc/linux/drivers/net/ethernet/hisilicon/hns/ |
H A D | hns_dsaf_xgmac.c | 443 mac_info->speed = MAC_SPEED_10000; in hns_xgmac_get_info()
|
/openbmc/linux/Documentation/arch/ia64/ |
H A D | fsys.rst | 119 speed comes a set of restrictions:
|
/openbmc/linux/drivers/gpu/drm/amd/display/dc/link/ |
H A D | link_detection.c | 301 .speed = ddc->ctx->dc->caps.i2c_speed_in_khz }; in i2c_read()
|
/openbmc/linux/arch/arm/boot/dts/qcom/ |
H A D | qcom-sdx55.dtsi | 433 max-link-speed = <3>;
|
/openbmc/linux/arch/arm/boot/dts/st/ |
H A D | ste-ux500-samsung-codina-tmo.dts | 8 * - No CPU speed cap, full ~1GHz rate
|
/openbmc/linux/arch/m68k/ |
H A D | Kconfig.cpu | 393 purposes. This will save a few bytes kernel size and may speed up
|
/openbmc/linux/drivers/net/ethernet/sfc/siena/ |
H A D | efx_common.c | 267 link_state->speed, link_state->fd ? "full" : "half", in efx_siena_link_status_changed()
|
/openbmc/linux/drivers/pcmcia/ |
H A D | rsrc_nonstatic.c | 305 map.speed = 0; in checksum()
|
/openbmc/linux/arch/arm64/boot/dts/qcom/ |
H A D | msm8994-msft-lumia-octagon.dtsi | 862 * Set the speed to HS200 as a safety measure.
|
H A D | ipq6018.dtsi | 756 max-link-speed = <3>;
|
/openbmc/docs/designs/ |
H A D | external-sensor.md | 187 setting, or fan speed setting). In this case, the timeout feature would not only
|
/openbmc/linux/drivers/net/dsa/microchip/ |
H A D | ksz9477.c | 309 if (p->phydev.speed == SPEED_1000) in ksz9477_r_phy()
|
/openbmc/linux/sound/usb/ |
H A D | stream.c | 94 subs->speed = snd_usb_get_speed(subs->dev); in snd_usb_init_substream()
|
/openbmc/linux/Documentation/admin-guide/ |
H A D | ext4.rst | 307 used is designed to automatically tune for the speed of the disk, by 376 mutex, which improves scalability on high speed storages. However this
|
/openbmc/qemu/hw/usb/ |
H A D | trace-events | 209 usb_dwc2_attach_speed(const char *speed) "%s-speed device attached"
|
/openbmc/linux/Documentation/scsi/ |
H A D | ncr53c8xx.rst | 495 Maximum speed = 1000/(4*period factor) except for special 708 - set synchronous negotiation speed to 10 Mega-transfers / second. 1167 | * Synchronous transfer speed | Y | Y | 1179 In order to speed up the system boot, for each device configured without
|
/openbmc/linux/drivers/net/ethernet/intel/i40e/ |
H A D | i40e_common.c | 4480 hw->bus.speed = i40e_bus_speed_2500; in i40e_set_pci_config_data() 4483 hw->bus.speed = i40e_bus_speed_5000; in i40e_set_pci_config_data() 4486 hw->bus.speed = i40e_bus_speed_8000; in i40e_set_pci_config_data() 4489 hw->bus.speed = i40e_bus_speed_unknown; in i40e_set_pci_config_data()
|
/openbmc/u-boot/common/spl/ |
H A D | Kconfig | 491 ICs (PMICs) before raising the CPU clock speed, for example. 711 so that the clock speed can be increased. This enables the drivers 828 temperature sensors to permit warnings, speed throttling or even
|
/openbmc/linux/drivers/hwmon/ |
H A D | it87.c | 1313 int speed; in show_fan() local 1319 speed = has_16bit_fans(data) ? in show_fan() 1323 return sprintf(buf, "%d\n", speed); in show_fan()
|
/openbmc/linux/Documentation/admin-guide/device-mapper/ |
H A D | cache.rst | 220 bits in a separate btree, which improves speed of
|
/openbmc/u-boot/doc/ |
H A D | README.rockchip | 301 - Run CPU at full speed (code exists but we only see ~60 DMIPS maximum)
|