| /openbmc/linux/drivers/net/dsa/ocelot/ |
| H A D | felix.c | 1097 int speed, int duplex, in felix_phylink_mac_link_up() argument
1104 interface, speed, duplex, tx_pause, rx_pause, in felix_phylink_mac_link_up()
1108 felix->info->port_sched_speed_set(ocelot, port, speed); in felix_phylink_mac_link_up()
|
| /openbmc/linux/drivers/net/ethernet/freescale/ |
| H A D | ucc_geth.c | 1583 if (phydev->speed != ugeth->oldspeed) { in adjust_link()
1585 switch (phydev->speed) { in adjust_link()
1603 if (phydev->speed == SPEED_10) in adjust_link()
1613 dev->name, phydev->speed); in adjust_link()
1616 ugeth->oldspeed = phydev->speed; in adjust_link()
|
| /openbmc/linux/drivers/net/ethernet/microchip/ |
| H A D | lan743x_main.c | 1159 switch (phydev->speed) { in lan743x_sgmii_config()
1186 "Invalid speed %d\n", phydev->speed); in lan743x_sgmii_config()
1433 switch (phydev->speed) { in lan743x_phy_link_status_change()
1460 lan743x_ptp_update_latency(adapter, phydev->speed); in lan743x_phy_link_status_change()
1500 .speed = SPEED_1000, in lan743x_phy_open()
|
| /openbmc/u-boot/tools/buildman/ |
| H A D | README | 517 5cc29db lcd: Add CONFIG_CONSOLE_SCROLL_LINES option to speed console
576 16: lcd: Add CONFIG_CONSOLE_SCROLL_LINES option to speed console
605 16: lcd: Add CONFIG_CONSOLE_SCROLL_LINES option to speed console
937 work 'make' does, and hence speed up the build. This flag will speed up any
1187 the build speed by building all commits for a board instead of the other
|
| /openbmc/linux/Documentation/driver-api/usb/ |
| H A D | power-management.rst | 656 hi-speed peer::
662 peer ports are simply the hi-speed and superspeed interface pins that
667 connection and attempt to connect to the hi-speed pins. The
670 1. Port suspend is sequenced to guarantee that hi-speed ports are powered-off
|
| /openbmc/linux/drivers/usb/host/ |
| H A D | isp1362-hcd.c | 330 ptd->mps = PTD_MPS(ep->maxpacket) | PTD_SPD(urb->dev->speed == USB_SPEED_LOW) | in prepare_ptd()
1301 ep->load = usb_calc_bus_time(udev->speed, !is_out, in isp1362_urb_enqueue()
2137 (ep->udev->speed == USB_SPEED_FULL) ? "" : "ls ", in isp1362_show()
2150 (ep->udev->speed == USB_SPEED_FULL) ? "" : "ls ", in isp1362_show()
|
| /openbmc/linux/drivers/net/ethernet/marvell/ |
| H A D | mvneta.c | 3987 state->speed = in mvneta_pcs_get_state()
3991 state->speed = SPEED_100; in mvneta_pcs_get_state()
3993 state->speed = SPEED_10; in mvneta_pcs_get_state()
4243 int speed, int duplex, in mvneta_mac_link_up() argument
4259 if (speed == SPEED_1000 || speed == SPEED_2500) in mvneta_mac_link_up()
4261 else if (speed == SPEED_100) in mvneta_mac_link_up()
|
| /openbmc/linux/Documentation/netlabel/ |
| H A D | draft-ietf-cipso-ipsecurity-01.txt | 237 speed many implementations including router implementations.
334 speed many implementations including router implementations.
386 speed many implementations including router implementations.
|
| /openbmc/linux/net/ipv4/ |
| H A D | Kconfig | 524 congestion control for high speed network links. It uses a
608 YeAH-TCP is a sender-side high-speed enabled TCP congestion control
622 high speed long delay links. It uses round-trip-time to
|
| /openbmc/linux/Documentation/mhi/ |
| H A D | mhi.rst | 14 speed peripheral buses or shared memory. Even though MHI can be easily adapted
|
| /openbmc/linux/drivers/mtd/maps/ |
| H A D | pcmciamtd.c | 382 pr_debug("Region %d, speed = %u ns\n", i, t->dev[i].speed); in pcmciamtd_cistpl_device()
|
| /openbmc/linux/Documentation/networking/ |
| H A D | plip.rst | 83 mode as compared to IRQ mode as far as the data transfer speed is involved.
|
| /openbmc/u-boot/arch/arm/dts/ |
| H A D | imx6-logicpd-baseboard.dtsi | 384 /* fsl,max-link-speed = <2>; */
|
| H A D | rk3288-tinker.dtsi | 500 * high-speed mode on EVB board so bump up to 8ma.
|
| H A D | rk3288-phycore-som.dtsi | 416 * We run eMMC at max speed; bump up drive strength.
|
| H A D | rv1108.dtsi | 281 max-speed = <100>;
|
| /openbmc/u-boot/include/ |
| H A D | imx_lpi2c.h | 17 int speed; member
|
| /openbmc/u-boot/drivers/usb/host/ |
| H A D | xhci-ring.c | 779 if (udev->speed == USB_SPEED_FULL) { in xhci_ctrl_tx()
|
| /openbmc/u-boot/drivers/net/ |
| H A D | zynq_gem.c | 499 switch (priv->phydev->speed) { in zynq_gem_init()
|
| /openbmc/qemu/pc-bios/ |
| H A D | petalogix-ml605.dts | 203 current-speed = < 0x2580 >;
|
| /openbmc/u-boot/doc/ |
| H A D | README.falcon | 10 Falcon Mode is introduced to speed up the booting process, allowing
|
| /openbmc/qemu/docs/system/ |
| H A D | security.rst | 24 safely on the physical CPU at close-to-native speed.
|
| /openbmc/linux/sound/firewire/bebob/ |
| H A D | bebob_stream.c | 428 conn->resources.channel, conn->speed); in start_stream()
|
| /openbmc/phosphor-dbus-interfaces/yaml/org/freedesktop/UPower/ |
| H A D | Device.interface.yaml | 33 more accurate, at the expense of plotting speed."
|
| /openbmc/docs/designs/ |
| H A D | device-tree-gpio-naming.md | 126 supply fans run at full speed (Fans Full Speed). When toggled low, then high, it
|