| /openbmc/linux/drivers/media/test-drivers/vivid/ |
| H A D | vivid-ctrls.c | 1070 if (dev->output_type[dev->output] != HDMI) in vivid_vid_out_s_ctrl()
1073 dev->display_present[dev->output] = ctrl->val; in vivid_vid_out_s_ctrl()
1088 bus_idx = dev->cec_output2bus_map[dev->output]; in vivid_vid_out_s_ctrl()
|
| /openbmc/linux/Documentation/admin-guide/pm/ |
| H A D | amd-pstate.rst | 427 be used to enable them and see their output (if the kernel is
476 about part of the output. ::
577 [-o <output-file-for-dump>]
|
| /openbmc/linux/Documentation/sound/designs/ |
| H A D | midi-2.0.rst | 143 Direction: output
234 proc output.
241 give you the output like::
|
| /openbmc/linux/include/net/ |
| H A D | xfrm.h | 396 int (*output)(struct net *net, struct sock *sk, struct sk_buff *skb); member
433 int (*output)(struct xfrm_state *, struct sk_buff *pskb); member
646 } output; member
|
| /openbmc/linux/Documentation/networking/ |
| H A D | bonding.rst | 1695 classes of traffic to certain physical interfaces on output to implement
1709 The output of the file /proc/net/bonding/bondX has changed so the output Queue
1754 ip of 192.168.1.100 have their output queue mapping value overwritten to 2.
1755 This value is then passed into the driver, causing the normal output path
1759 that normal output policy selection should take place. One benefit to simply
1763 a pass-through for selecting output queues on the slave device rather than
1764 output port selection.
1767 output slave selection was limited to round-robin and active-backup modes.
1854 devices will have the SLAVE flag set. The ifconfig output does not
2650 output from ping flags duplicates (typically one per slave).
[all …]
|
| /openbmc/openbmc/poky/bitbake/doc/bitbake-user-manual/ |
| H A D | bitbake-user-manual-execution.rst | 10 output such as a single installable package, a kernel, a software
439 the run file and the output in the log files is a useful debugging
476 changes because it should not affect the output for target packages. The
520 ``-DDD``), BitBake produces output when it discovers something for which
|
| /openbmc/linux/arch/arm64/boot/dts/rockchip/ |
| H A D | rk356x.dtsi | 228 clock-output-names = "xin24m";
235 clock-output-names = "xin32k";
1772 clock-output-names = "clk_usbphy0_480m";
1794 clock-output-names = "clk_usbphy1_480m";
|
| /openbmc/linux/arch/arm64/boot/dts/mediatek/ |
| H A D | mt8186.dtsi | 633 clock-output-names = "clk13m";
640 clock-output-names = "clk26m";
647 clock-output-names = "clk32k";
1691 clock-output-names = "mipi_tx0_pll";
|
| /openbmc/linux/Documentation/driver-api/ |
| H A D | pin-control.rst | 27 output line you want to control and these are denoted by unsigned integers
193 may be able to make an output pin high impedance (Hi-Z), or "tristate" meaning it is
733 GPIO pin shall be used for input or output you can implement the
832 such as setting a GPIO's output value, reading a GPIO's input value, or
867 this will configure the pin in output, use argument
933 How the registers are poked to attain the push or pull, and output low
|
| /openbmc/linux/Documentation/gpu/ |
| H A D | tegra.rst | 117 by the versatile SOR output, which supports eDP, DP and HDMI. The SOR is able
|
| /openbmc/linux/Documentation/userspace-api/media/drivers/ |
| H A D | omap3isp-uapi.rst | 173 module's data output depends on the requested configuration. Although the
|
| /openbmc/linux/Documentation/ABI/testing/ |
| H A D | sysfs-devices-edac | 118 the output can provide the DIMM label in the system log.
|
| /openbmc/linux/Documentation/core-api/ |
| H A D | debugging-via-ohci1394.rst | 139 ------> Press Ctrl-T now, the output should be similar to:
|
| /openbmc/linux/arch/m68k/ifpsp060/ |
| H A D | isp.doc | 54 then converting the resulting binary output image into an
|
| H A D | fpsp.doc | 46 then converting the resulting binary output image into an
|
| /openbmc/linux/Documentation/powerpc/ |
| H A D | bootwrapper.rst | 49 output image file can be either an elf file or a flat
|
| /openbmc/linux/drivers/video/fbdev/matrox/ |
| H A D | matroxfb_Ti3026.c | 701 minfo->outputs[0].output = &ti3026_output; in Ti3026_preinit()
|
| /openbmc/qemu/tests/qemu-iotests/ |
| H A D | 033.out | 1 QA output created by 033
|
| H A D | 097.out | 1 QA output created by 097
|
| /openbmc/u-boot/board/keymile/km_arm/ |
| H A D | kwbimage_256M8_1.cfg | 179 # bit 12: 0, DDR output buffer enabled
|
| H A D | kwbimage_128M16_1.cfg | 179 # bit 12: 0, DDR output buffer enabled
|
| /openbmc/linux/Documentation/userspace-api/media/v4l/ |
| H A D | v4l2.rst | 170 VIDIOC_ENUM_DV_PRESET. Remove the related v4l2_input/output
|
| /openbmc/linux/Documentation/leds/ |
| H A D | ledtrig-transient.rst | 160 - Use by any user space app that needs a transient GPIO output.
|
| /openbmc/linux/tools/testing/selftests/net/ |
| H A D | icmp_redirect.sh | 483 -v verbose mode (show commands and output)
|
| /openbmc/linux/Documentation/driver-api/surface_aggregator/clients/ |
| H A D | cdev.rst | 19 These IOCTLs and their respective input/output parameter structs are defined in
|